实用型深度光氧化设备对几种染料和多菌灵农药废水的处理

利用HFS-1型深度光氧化废水处理设备对活性艳蓝K3R、酸性红3B、活性黑KNB、酸性红A、直接耐酸大红4BS等5种染料的水溶液和多菌灵农药废水进行了深度光氧化处理。结果表明：（1）染料在处理5min后，脱色率都在90%以上；处理15min后，CODCr的去除率除活性艳蓝K3R较低外，其余的都在80%以上；BOD5/CODCr的值都有所增大。（2）多菌录农药废水（经稀释）处理40min后CODCr的去除率为57.0%，BOD5/CODCr的值由0.20增加到0.44。（3）采用深度光氧化-絮凝的工艺处理多菌灵农药废水，CODCr的去除率为57.5%。     

微电解与Fenton试剂预处理农药废水的试验研究

农药废水是一种典型的高浓度有机工业废水 ,有机污染物浓度高 (CODCr>10 0 0 0mg L) ,可生化性差 (氯苯农药废水BOD5 CODCr=0 .0 3 ,对邻硝基氯苯农药废水BOD5 CODCr=0 .0 5 )。采用微电解和Fenton试剂氧化两种物化手段对菊酯、氯苯和对邻硝氯苯 3种废水按比例配制而成的综合农药废水进行预处理 ,结果表明 :在废水pH为 2— 2 .5时 ,经微电解处理后 ,BOD5 CODCr比值在 0 .45以上 ,可生化性提高 ;Fenton试剂对综合农药废水CODCr去除率为 60 %左右 ,色度去除率接近 10 0 %     

高压电晕与臭氧联用对不同结构染料脱色效果的比较研究

比较研究了高压电晕与臭氧联用对活性艳红X-3B(单偶氮)、活性艳蓝X-BR(蒽醌)、活性黑KN-GRRC(双偶氮)、酸性红ARL(单偶氮)、酸性蓝BRL(蒽醌)、酸性橙AGT(双偶氮)和分散蓝2BLN(蒽醌)7种染料模拟废水的脱色效果.结果显示,酸性橙AGT模拟废水的脱色速度较慢,而其他6种染料在15 min内都能完全脱色,这表明染料结构本身的差异决定了脱色效果;活性染料模拟废水的脱色效果优于酸性染料;蒽醌染料和单偶氮染料模拟废水的脱色效果明显好于双偶氮染料.     

改进Fenton体系处理蒽醌染料的研究

以活性艳蓝KN-R作为研究对象,用UV/Fenton和solar/Fenton/草酸(H2C O4)体系对其进行处理,对反应体系的影响因素作综合的评价.得到处理蒽醌染料废水的最佳条件:dye(活性艳蓝KN-R):Fe2 :H2O2:H2C2O4为5:1:15:1.5,pH为3.0,反应时间为40 min.在最佳条件下,solar/Fenton/H2C2O4体系脱色率达到100%,COD和TOC去除率分别达到87%和66%以上.改进的Fenton方法能使难降解有机染料迅速脱色,矿化程度较高.并对此体系处理活性艳蓝KN-R废水的脱色过程进行动力学模拟,得到此反应为拟一级反应.     

青霉菌对印染废水吸附脱色及深度处理的研究

利用青霉菌P 1(Penicilliumsp )对 2种染浴废水中的染料进行吸附去除 ,研究结果表明 ,吸附处理 3h ,黑色和红色染浴废水色度基本被去除 ,去除率分别达 98 0 %和 74 5 % ,但去色处理后废水的CODCr值仍偏高。对去除色度的废水进一步用活性污泥进行深度处理 ,黑色和红色废水的CODCr去除率分别为 75 9%和 89 7%。青霉菌菌丝通过吸附作用从废水中抽提出的染料分子在有染料降解细菌L 1和L 2的降解池中脱色降解 ,菌丝吸附脱色能力得到再生。     

染料废水的脱色研究

模拟中温(35℃左右)厌氧消化条件,以葡萄糖为共基质,对模拟染料废水的厌氧生物脱色进行了研究.结果表明对可溶性的活性染料处理效果,脱色率和COD去除率可分别达到90%和70%左右.特别是对红、紫、橙三色染料处理效果好,如活性红KD-8B、活性艳兰KGL、活性金黄MG、活性红紫KN-2R、活性艳橙KGN等.当染料浓度在1.0 g/L以下,都没有抑制;脱色在22 h就可达90%的脱色率;污泥负荷在2～4 g/L时,处理效果最佳.实验亦证实,在厌氧处理过程中,染料分子结构发生了明显的变化.     

基于Ti/SnO_2阳极氧化法的典型染料废水电化学氧化规律

采用Ti/SnO2电极间接阳极氧化法处理直接深棕M和活性艳蓝KNR模拟染料废水,研究电解质种类、pH、电压、NaCl投加量及电解时间对其降解效果的影响;在最佳组合条件下,通过分析UV-Vis光谱以及降解过程中氮元素的存在形式,研究上述2种染料的降解规律。结果表明,在pH为3,电压20 V,NaCl投加量为2.5 g/L的条件下,电解30 min后,直接深棕M和活性艳蓝KNR的脱色率分别达到80%和95%,60 min后直接深棕M的COD去除率可达75%,活性艳蓝KNR的COD去除率达到90%;电解60 min后,直接深棕M的偶氮双键完全破坏,萘环和苯环结构被逐步降解,活性艳蓝KNR溶液电解2 min,其分子结构中的蒽醌共轭体系被破坏,随反应的进行,蒽醌结构逐渐被破坏,染料逐步降解。     

载Ni-Cu-K活性炭催化氧化法处理染料废水活性红X-3B

以载Ni活性炭为催化剂 ,用空气氧化模拟染料废水活性红X 3B。实验结果表明 ,负载在活性炭上的金属离子起到催化氧化的作用。活性炭对活性红X 3B的COD和色度的去除率能达到 98 74 %以上 ,较不加金属的活性炭去除率提高 30 % ,用活性炭处理浓度为 0 4g/L的模拟废水活性红X 3B ,投加量为 5g/L时 ,催化氧化效果最明显 ,催化氧化作用对色度的去除率达 2 5 33%。     

基于Ti/SnO2阳极氧化法的典型染料废水电化学氧化规律

采用Ti／SnO2电极间接阳极氧化法处理直接深棕M和活性艳蓝KNR模拟染料废水,研究电解质种类、pH、电压、NaCl投加量及电解时间对其降解效果的影响;在最佳组合条件下,通过分析uV—Vis光谱以及降解过程中氮元素的存在形式,研究上述2种染料的降解规律。结果表明,在pH为3,电压20V,NaCl投加量为2．5g／L的条件下,电解30min后,直接深棕M和活性艳蓝KNR的脱色率分别达到80％和95％,60min后直接深棕M的COD去除率可达75％,活性艳蓝KNR的COD去除率达到90％;电解60min后,直接深棕M的偶氮双键完全破坏,萘环和苯环结构被逐步降解,活性艳蓝KNR溶液电解2min,其分子结构中的蒽醌共轭体系被破坏,随反应的进行,蒽醌结构逐渐被破坏,染料逐步降解。     

臭氧催化氧化处理活性蓝染料废水及催化剂的研究

进行了臭氧化学氧化体系和臭氧催化氧化体系对活性蓝处理效果的比较。提出了常温常压下臭氧催化氧化预处理活性蓝染料废水的新方法。实验结果表明,臭氧催化氧化处理COD为13 800 mg/L的活性蓝染料废水时,最佳反应pH值为5～6,臭氧用量为80 mg/L时,反应时间约40 min,COD去除率大于80%,色度去除率大于90%,达到了预处理要求。     

Decolorization and biodegradability of photocatalytic treated azo dyes and wool textile wastewater

The photodegradation and biodegradability have been investigated for four non-biodegradable commercial azo dyes, Reactive YellowKD-3G, Reactive Red 15, Reactive Red 24, Cationic Blue X-GRL, an indicator. Methyl Orange, and one industrial wool textile wastewater, using TiO2 suspensions irradiated with a medium pressure mercury lamp. The color removal of dyes solution and dyeing wastewater reached to above 90% within 20-30 min. of photocatalytic treatment. Biochemical oxygen demand (BOD) was found to increase, while chemical oxygen demand (COD), total organic carbon (TOC) decreased, so that the ratio of BOD5/COD of the wastewater increased from original zero up to 0.75. The result implies that photocatalytic oxidation enhanced the biodegradability of the dye-containing wastewater and therefore relationship between decolorization and biodegradability exists. When the color disappeared completely, the wastewater biodegraded normally and could be discharged for further treatment. The experimental results demonstrate that it is possible to combine photocatalysis with conventional biological treatment for the remedy of wastewater containing generally non-biodegradable azo dyes.     

Decolorization and degradation of H-acid and other dyes using ferrous-hydrogen peroxide system

In this study, advanced oxidation process utilizing Fenton's reaction was investigated for the decolorization and degradation of two commercial dyes viz., Red M5B, Blue MR and H-acid, a dye intermediate used in chemical industries for the synthesis of direct, reactive and azo dyes. Effect of Fe2 +, H2O2, pH, and contact time on the degradation of the dyes was studied. Maximum color and COD removal was obtained for Red MSB, H-acid and Blue MR at 10-25 mg/l of Fe2+ dose and 400-500 mg/l of H2O2 dose at pH 3.0. The initial oxidation reaction was found to fit into first order rate kinetics and the rate of oxidation of H-acid was higher than the other dyes. Release of chloride and sulfate from the Fenton's treated Red M5B dye and sulfate from H-acid and Blue MR indicates that the dye degradation proceeds through cleavage of the substituent group.     

Semiconductor-assisted photocatalytic degradation of reactive dyes in aqueous solution

This work reports the semiconductor-assisted photochemical degradation of reactive dyes. In an oxygenated-UV-ZnO system almost total decolorization of Remazol Brilliant Blue R, Remazol Black B, Reactive Blue 221 and Reactive Blue 222 was observed in reaction times of about 60 min. Extending the photochemical treatment up to 120 min, mineralization higher than 80% for all the dyes was observed. During the same period, the residual acute toxicity was significantly reduced only for Remazol Black B. A systematic optimization study carried out by factorial design showed that for the reactive dyes tested, the ZnO semiconductor exhibits a better efficiency than that observed with anatase TiO2. A synergistic effect in the coupled TiO2-ZnO system was not observed.     

Comparative use of bacterial, algal and protozoan tests to study toxicity of azo- and anthraquinone dyes

Toxicity of two azo dyes (Reactive Orange 16 (RO16); Congo Red (CR)) and two anthraquinone dyes (Remazol Brilliant Blue R (RBBR); Disperse Blue 3 (DB3)) were compared using bacterium Vibrio fischeri, microalga Selenastrum capricornutum and ciliate Tetrahymena pyriformis. The following respective endpoints were involved: acute toxicity measured as bacterial luminescence inhibition, algal growth inhibition, and the effects on the protozoa including viability, growth inhibition, grazing effect and morphometric effects. In addition, mutagenicity of the dyes was determined using Ames test with bacterium Salmonella typhimurium His(-). DB3 dye was the most toxic of all dyes in the bacterial, algal and protozoan tests. In contrast to other dyes, DB3 exhibited mutagenic effects after metabolic activation in vitro in all S. typhimurium strains used. Of the methods applied, the algal test was the most sensitive to evaluate toxicity of the dyes tested.     

Fenton试剂和氨吹脱法处理苯唑醇废水的试验研究

采用Fenton试剂催化氧化和氨吹脱法对苯唑醇生产废水的处理进行了研究。实验结果表明 ,此方法对废水的CODCr和氨氮具有良好的去除效果 ,平均去除率分别达到 73 .5 %和 95 %以上。处理后废水的BOD5 CODCr>0 .45 ,其可生化性良好。该技术具有能耗低、操作简便等优点     

Fenton氧化-生化组合工艺处理染料中间体废水

针对染料中间体废水具有COD高、BOD5/COD低和具有生物毒性的特性,采用Fenton氧化-水解酸化-好氧组合工艺进行染料中间体生产废水的处理试验,试验结果表明:废水经Fenton氧化及水解酸化工序后,废水的BOD5/COD值由0.03升高至0.48,经好氧生化工序处理后的出水COD和BOD5浓度分别达122.6 mg/L和54.6 mg/L,符合《污水综合排放标准》(GB8978-1996)二级标准,该组合工艺COD总去除率达94%.     

Biological treatment of dye wastewaters using an anaerobic-oxic system

Three dye solutions, namely, C.I. Acid Yellow 17, C.I. Basic Blue 3, and C.I. Basic Red 2, were treated in an upflow anaerobic sludge blanket (UASB) reactor followed by a semi-continuous aerobic activated sludge tank. When hydraulic retention time was about 12 hours, no significant color removal was observed in the aerobic stage. In the anaerobic stage, Acid Yellow 17, Basic Blue 3, and Basic Red 2 were removed by 20%, 72%, and 78%, respectively. To treat wastewater from a dye manufacturing factory with COD concentration of 1200 mg/l and Color of 500 degree (dilution factor), an UASB reactor (4.5 liters) and an activated sludge tank (5 liters, adjustable), COD and color were removed by more than 83% and 90% at a COD loading rate of 5.3 kg COD/m³-day in the anaerobic stage, and at the hydraulic retention time of 6-10 hours for the anaerobic stage and 6.5 for the aerobic stage. The anaerobic stage of the A/O system removes both color and COD. In addition, it also improves biodegradability of dyes for further aerobic treatment.