Direct comparison of amphipod sensitivities to dredged sediments from Spanish ports

The sensitivity of the benthic amphipod species Ampelisca brevicornis and Corophium volutator to dredged sediments was compared through simultaneous testing on the standard 10 days sediment toxicity test. The results of mortality obtained for 22 harbor sediments sampled at several Spanish ports were studied together with the physico-chemical characteristics of the samples to obtain the incidence of toxicity in terms of dredged material categories and to identify possible differences in the amphipod mortality results when using one or another test species. The results showed a similar incidence of toxicity for medium-high and highly contaminated sediments for both amphipod species, similar to that obtained through the comparison of the chemical concentrations measured in sediments with the single limit values used in Spain for dredged material characterization and management. On the contrary, C. volutator presented a higher mortality and a higher incidence of toxicity when exposed to low and medium-low contaminated sediments, which may have been caused by the lower sensitivity of A. brevicornis when exposed to sediments from its natural environment. When compared to other amphipod species used for whole sediment toxicity assessment, both amphipod species used in this study reported slightly higher sensitivities although these differences could have been associated to the different set of chemical compounds considered when characterizing the sediment samples. In this sense, the amphipod mortality results were better predicted through the use of mean quotients than just by comparing the measured chemical concentrations with the single limit values used in Spain, which indicates that the toxic response of both species was caused by the cocktail of contaminants present in the sediments. Finally, the correlation analysis identified a higher association between A. brevicornis mortality and the metallic contaminants while C. volutator was more correlated with the organic micro-pollutants. Despite these differences, the results indicate that Ampelisca brevicornis can be used as test organism for dredged material characterization when enough individuals of other recommended species such as Corophium volutator are not available.     

Impact of dredged urban river sediment on a Saronikos Gulf dumping site (Eastern Mediterranean): sediment toxicity,contaminant levels,and biomarkers in caged mussels

Impacts of chemical contaminants associated with dumping of dredged urban river sediments at a coastal disposal area in Saronikos Gulf (Eastern Mediterranean) were investigated through a combined approach of sediment toxicity testing and active biomonitoring with caged mussels. Chemical analyses of aliphatic hydrocarbons (AHs), polycyclic aromatic hydrocarbons (PAHs), Cu, and Zn in combination with the solid phase Microtox® test were performed on sediments. Concentrations of PAHs, AHs, Cu, and Zn as well as multiple biomarkers of contaminant exposure and/or effects were measured in caged mussels. Sediments in the disposal and neighboring area showed elevated PAHs and AHs concentrations and were characterized as toxic by the solid-phase Microtox® test during and after dumping operations. Biomarker results in the caged mussels indicated sublethal effects mainly during dumping operations, concomitantly with high concentrations of PAHs and AHs in the caged mussel tissues. Cu and Zn concentrations in sediments and caged mussels were generally not elevated except for sediments at the site in the disposal area that received the major amount of dredges. High PAHs and AHs levels as well as sublethal effects in the caged mussels were not persistent after termination of operations. The combined bioassay–biomarker approach proved useful for detecting toxicological impacts of dredged river sediment disposal in sediments and the water column. Nevertheless, further research is needed to evaluate whether sediment toxicity will have long-term effects on benthic communities of the disposal area.     

Environmental impact and recovery at two dumping sites for dredged material in the North Sea

The environmental impact and recovery associated with the long and uninterrupted disposal of large volumes of moderately contaminated dredged material from the port of Rotterdam was studied at nearby dumping sites in the North Sea. Observations were made on sediment contamination, ecotoxicity, biomarker responses and benthic community changes shortly after dumping at the 'North' site had ceased and at the start of disposal at the new dumping site 'Northwest'. During the period of dumping, very few benthic invertebrates were found at the North site. Concentrations of cadmium, mercury, polychlorinated biphenyls (PCBs), polyaromatic hydrocarbons (PAHs) and tributyltin (TBT) in the fine sediment fraction (<63 microm) from this site were 2-3 times higher than at the reference site. In four different bioassays with marine invertebrates the sediments showed no acute toxic effects. In tissue (pyloric caeca) of resident starfish Asterias rubens, residual levels of mercury, zinc, PCBs and dioxin-like activity were never more than twice those at the reference site. Four different biomarkers (DNA integrity, cytochrome P450 content, benzo[a]pyrene hydroxylase activity and acetylcholinesterase inhibition) were used on the starfish tissues, but no significant differences were found between North and the reference site. Minor pathological effects were observed in resident dab Limanda limanda. One year after dumping had ceased at the North site, a significant increase in the species richness and abundance of benthic invertebrates and a concomitant decrease in the fine sediment fraction of the seabed were observed. After 8.2 million m3 of moderately contaminated dredged material had been dumped at the new dumping site Northwest, the species richness and abundance of benthic invertebrates declined over an area extending about 1-2 km eastwards. This correlated with a shift in sediment texture from sand to silt. The contamination of the fine sediment fraction at the Northwest location doubled. It is concluded that marine benthic resources at and around the dumping sites have been adversely affected by physical disturbance (burial, smothering). However, no causal link could be established with sediment-associated contaminants from the dredged spoils.     

Using Various Guidelines and Approaches for the Assessment of Marine Sediment Quality

The aim of the present study is to explore the implications of using different quality guidelines and approaches for marine sediment characterization. As a case study, the sediments of Souda Port, Crete, Greece, were examined in order to assess heavy metal contamination and to estimate anthropogenic contribution and potential adverse effects to aquatic environment, as well as to indicate feasible future management options. The concentration of six heavy metals (Co, Cr, Cu, Ni, Pb, and Zn) was determined and compared with different sediment quality guidelines (SQGs) and regional/national criteria established for dredged material characterization and management. In addition, the geo-accumulation index (I_geo) was calculated and the sediments toxicity and heavy metals bioavailability were determined. Based on the experimental data, it is deduced that Souda sediments are characterized as moderately polluted only in terms of Co, Ni, and Pb.     

Development and application of long-term sublethal whole sediment tests with Arenicola marina and Corophium volutator using Ivermectin as the test compound

Short-term whole sediment tests using the amphipod Corophium volutator and the polychaete Arenicola marina are now routinely used in Europe to assess the acute toxicity of marine sediments. However, there is still a need to develop longer-term assays which measure effects on sublethal endpoints that are more relevant to predicting impacts at the population level. The effect of increasing exposure times and measuring additional endpoints such as growth, on the sensitivity of these assays was investigated. The test compound used was the chemotherapeutant Ivermectin (IVM), used in aquaculture to treat sea lice infestations. IVM was found to be acutely toxic to both test organisms. Extending the lugworm test to 100 days increased sensitivity of survival by a factor of three; a significant reduction in casting rate was observed at concentrations an order of magnitude lower. This assay shows potential for detecting the sublethal effects of low concentrations of sediment contaminants. Increasing the exposure time did not seem to affect the sensitivity of the amphipod, but further method development is required.     

Metal solubility as a function of pH in a contaminated, dredged sediment affected by oxidation

The solubility as a function of pH for metals in a reduced dredged sediment, subjected to different redox conditions, was studied in a laboratory experiment. The redox conditions imposed simulated (i) the undisturbed sediment (flooded), (ii) a dredged material stored in a confined pond (aerated once and then flooded), (iii) an upland stored dredged material (drained and dried), and (iv) an upland stored sediment subjected to tillage (drained, dried and mixed). Minor differences in the solubility as a function of pH were observed between the treatments after two weeks. After three months, the solubility of Cd, Cu, Pb and Zn increased strongly in the oxidized sediments. Leachability of Fe decreased, while Mn, Ni and Co were mostly unaffected. Both short- and long-term mobility of metals (except Fe) is expected to be lowest when a reduced sediment remains in reduced conditions. Studying the solubility as a function of pH may provide additional information on the chemical association of metals in sediments.     

Genotoxic and teratogenic potential of marine sediment extracts investigated with comet assay and zebrafish test

Organic extracts of marine sediments from the North Sea and the Baltic Sea were investigated with two toxicity assays. The comet assay based on the fish cell line Epithelioma papulosum cyprini (EPC) was applied to determine the genotoxic potential; zebrafish embryos (Danio rerio) were used to quantify the teratogenic potential of the samples. EC(50) values were calculated from dose-response curves for both test systems. Highest teratogenic and genotoxic effects normalised to total organic carbon (TOC) content were detected in sediment samples of different origins. Polychlorinated biphenyls (PCBs) and polycyclic aromatic hydrocarbons (PAHs) are not likely to be the causes of the observed effects, as demonstrated by a two-step fractionation procedure of selected extracts. The toxic potential was more pronounced in fractions having polarity higher than those possessed by PAHs and PCBs. The suitability of the two in vitro test systems for assessing genotoxic and teratogenic effects of marine sediment extracts could be demonstrated.     

Batch and column studies of the stabilization of toxic heavy metals in dredged marine sediments by hematite after bioremediation

The management of dredged sediments is an important issue in coastal regions where the marine sediments are highly polluted by metals and organic pollutants. In this paper, mineral-based amendments (hematite, zero-valent iron and zeolite) were used to stabilize metallic pollutants (As, Cd, Cu, Mo, Ni, Pb, and Zn) in a contaminated marine sediment sample. Mineral-based amendments were tested at three application rates (5 %, 10 %, and 15 %) in batch experiments in order to select the best amendment to perform column experiments. Batch tests have shown that hematite was the most efficient amendment to stabilize inorganic pollutants (As, Cd, Cu, Mo, Ni, Pb, and Zn) in the studied sediment. Based on batch tests, hematite was used at one application rate equal to 5 % to conduct column experiments. Column tests confirmed that hematite was able to decrease metal concentrations in leachates from stabilized sediment. The stabilization rates were particularly high for Cd (67 %), Mo (80 %), and Pb (90 %). The Microtox solid phase test showed that hematite could decrease significantly the toxicity of stabilized sediment. Based on batch and column experiments, it emerged that hematite could be a suitable adsorbent to stabilize metals in dredged marine sediment.     

The SeKT joint research project: definition of reference conditions, control sediments and toxicity thresholds for limnic sediment contact tests

- In current biotest approaches, intact organisms or in vitro systems are exposed to sediments using different exposure scenarios. The most important issue in sediment toxicity testing protocols is the question which test phase (solid or liquid) should be used. Whole-sediment exposure protocols represent the most realistic scenario to simulate in situ exposure conditions in the laboratory. However, until now there is no agreement in how to acquire and to evaluate the data of the various available sediment contact assays. The SeKT joint research project was initiated with the aim to compare recently developed sediment contact assays by addressing reference conditions, control sediments and toxicity thresholds for limnic sediment contact tests.     

The toxicity of composted sediments from Mediterranean ports evaluated by several bioassays

This work investigates the ecotoxicological evaluation of contaminated dredged sediments from French Mediterranean navy harbour (A), commercial port (B) and two composite specimens (C) and (D) coming from the mixture of A and B with other port sediments. The toxicity of elutriates from these sediments is estimated using embryo-toxicity test, Microtox® solid phase test, LuminoTox, phytotoxicity tests and genotoxicity test. Bioassay responses are not clearly correlated with chemical contamination in the whole sediment and vary as a function of tested organisms. The highest contaminated samples (A and C) are almost always more toxic than the less contaminated samples (B and D). Among composite sediments, the mixture effect with other sediments is not efficient to decrease toxicity in sample C, suggesting that other parameters influence toxicity level such as particle size or organic matter content. These parameters should be taken into consideration in order to improve the efficiency of the mixture process and produce composite sediments with low toxicity.     

Extraction of organic contaminants from marine sediments and tissues using microwave energy.

In this study, we compared microwave solvent extraction (MSE) to conventional methods for extracting organic contaminants from marine sediments and tissues with high and varying moisture content. The organic contaminants measured were polychlorinated biphenyl (PCB) congeners, chlorinated pesticides, and polycyclic aromatic hydrocarbons (PAHs). Initial experiments were conducted on dry standard reference materials (SRMs) and field collected marine sediments. Moisture content in samples greatly influenced the recovery of the analytes of interest. When wet sediments were included in a sample batch, low recoveries were often encountered in other samples in the batch, including the dry SRM. Experiments were conducted to test the effect of standardizing the moisture content in all samples in a batch prior to extraction. SRM1941a (marine sediment). SRM1974a (mussel tissue), as well as QA96SED6 (marine sediment), and QA96TIS7 (marine tissue), both from 1996 NIST Intercalibration Exercise were extracted using microwave and conventional methods. Moisture levels were adjusted in SRMs to match those of marine sediment and tissue samples before microwave extraction. The results demonstrated that it is crucial to standardize the moisture content in all samples, including dry reference material to ensure good recovery of organic contaminants. MSE yielded equivalent or superior recoveries compared to conventional methods for the majority of the compounds evaluated. The advantages of MSE over conventional methods are reduced solvent usage, higher sample throughput and the elimination of halogenated solvent usage.     

Integrative assessment of marine pollution in Galician estuaries using sediment chemistry,mussel bioaccumulation,and embryo-larval toxicity bioassays

An integrative assessment of environmental quality was carried out in selected sites along the Galician coast (NW Iberian Peninsula) combining analytical chemistry of seawater and sediments, bioaccumulation in the marine mussel, and embryo-larval sediment toxicity bioassays, in order to link biological and chemical criteria for the assessment of coastal pollution. Maximum values of Hg and Cu in seawater, sediment and mussels, were found in the inner part of Ria of Pontevedra, while maximum levels of organics (polychlorinated biphenyls, hexachlorobenzene and aldrin) were found in mussels from A Coru?a. Outstanding values of Cu, Pb and Zn have been found in seawater and sediment from a single site, P3, which also was the most toxic in the embryo-larval bioassays performed with four different phyla of marine organisms: mollusks, echinoderms, arthropods and chordates. Sediment quality effects range-median values provided a valuable reference to predict biological effects from sediment chemistry data, while effects range-low values were too conservative. Sediment toxicity could also be predicted by using a toxic-unit model based on published EC50 values for trace metals and mobilization factors independently obtained from measurements of metal contents in sediments and their elutriates. When chemical and toxicological data are independently used to arrange sampling sites by using non-metric multidimensional scaling, a remarkable degree of concordance between both types of configurations could be observed.     

A model compound study: the ecotoxicological evaluation of five organic contaminants employing a battery of marine bioassays

This paper describes the ecotoxicological evaluation of five organic contaminants frequently detected in marine sediments (tributyltin, triphenyltin, benzo[a]pyrene, fluoranthene, and PCB 153) using three marine species (Vibrio fischeri, Tetraselmis suecica, and Tisbe battagliai). The sensitivity of each species varied for all compounds. The triorganotins were consistently the most toxic to all species. The applicability of each test system to assess the acute toxicity of environmental contaminants and their use in Toxicity Identification Evaluation (TIE) is discussed. Suitability of the Microtox and T. battagliai tests for employment in TIE studies were further assessed through spiking experiments with tributyltin. Results demonstrated that the most effective treatment to remove organotin toxicity from the sample was the C18 resin. The results of this study have important implications for risk assessment in estuarine and coastal waters in Ireland, where, at present the monitoring of sediment and water quality is predominantly reliant on chemical analysis alone.     

Comparing growth development of <Emphasis Type="Italic">Myriophyllum</Emphasis> spp. in laboratory and field experiments for ecotoxicological testing

BACKGROUND, GOALS AND SCOPE: Risk assessment of herbicides and the evaluation of contaminated sediments based on algae and the macrophyte Lemna sp. alone may underestimate the potential hazard of certain compounds. Therefore, various test systems with Myriophyllum spp. have been developed recently to assess the phytotoxicity in surface waters and natural sediments. In the present study, experiments investigating the growth development of Myriophyllum spp. were performed in the laboratory under defined conditions and in mesocosms under environmentally realistic exposure conditions to evaluate the suitability of these species as potential standard test organisms in ecotoxicological testing. This study provides data on the endpoints biomass, plant length and root development. MATERIALS AND METHODS: Six independent experiments were performed to investigate the plant development of Myriophyllum spp. under control conditions. The main difference in the experiments was the complexity of the test systems ranging from simple laboratory experiments to complex outdoor mesocosm studies. At the start of each experiment, uniform cuttings of Myriophyllum spp. were placed in vessels with or without sediments to reduce variability between replicates. The endpoints considered in this investigation were biomass (fresh weight of the whole plant), length of the main shoot, length of the side shoots, total length of the plant (calculated from the length of the main and side shoots) and root formation. Root to shoot ratios were calculated as a further measure for plant development. Relative growth rates (RGR) based on plant length (RG(L)R) and on biomass (RG(B)R) were calculated. RESULTS: Despite the various experimental conditions, comparable growth was obtained in all test systems and the variability of endpoints, such as total length and biomass of plants, was low. It was observed that the RGR of M. spicatum in the simple laboratory test system with sediment were comparable to growth data obtained for M. verticillatum and M. spicatum grown in indoor and outdoor mesocosms, thus indicating that Myriophyllum growth tends to increase by the addition of sediment. High variability was determined for the endpoints length of the side shoots, total root length and biomass of roots. DISCUSSION: One challenge for a test design to investigate phytotoxicity on aquatic plants is to obtain good growth of the plants. From the results, it can be concluded that the experimental conditions in the various test systems were suitable to study the plant development of Myriophyllum spp. because obtained growth rates were comparable between laboratory and field investigations. Another challenge for developing a plant biotest system is the definition of sensitive endpoints. Low variability is preferred to detect minor effects of chemicals or polluted sediments on plant development. In our studies, the variability of the endpoints biomass and total length of plant was low and, therefore, they have much potential as endpoints for assessing toxicity. CONCLUSIONS: The methodologies presented in this study have applications within the risk assessment for aquatic plants and have the advantage of assessing effects taking into account the relevant exposure pathways via water and/or sediment for compounds under investigation. RECOMMENDATIONS AND PERSPECTIVES: Setting safe quality criteria for surface water and sediments is one of the challenges authorities are facing today. Myriophyllum spp. is recommended as suitable test species to investigate phytotoxicity in surface water and sediments. These results, thus, might serve as a basis for the compilation of a new harmonised guideline for ecotoxicological testing with aquatic macrophytes.     

Phytoremediation as a management option for contaminated sediments in tidal marshes, flood control areas and dredged sediment landfill sites

Background, aim and scope  

Polluted sediments in rivers may be transported by the river to the sea, spread over river banks and tidal marshes or managed, i.e. actively dredged and disposed of on land. Once sedimented on tidal marshes, alluvial areas or control flood areas, the polluted sediments enter semi-terrestrial ecosystems or agro-ecosystems and may pose a risk. Disposal of polluted dredged sediments on land may also lead to certain risks. Up to a few years ago, contaminated dredged sediments were placed in confined disposal facilities. The European policy encourages sediment valorisation and this will be a technological challenge for the near future. Currently, contaminated dredged sediments are often not valorisable due to their high content of contaminants and their consequent hazardous properties. In addition, it is generally admitted that treatment and re-use of heavily contaminated dredged sediments is not a cost-effective alternative to confined disposal. For contaminated sediments and associated disposal facilities used in the past, a realistic, low cost, safe, ecologically sound and sustainable management option is required. In this context, phytoremediation is proposed in the literature as a management option. The aim of this paper is to review the current knowledge on management, (phyto)remediation and associated risks in the particular case of sediments contaminated with organic and inorganic pollutants.     

Effects of storage method and duration on the toxicity of marine sediments to embryos of Crassostrea gigas oysters

The objective of laboratory sediment bioassays is to estimate in situ toxicity. This goal is difficult to achieve, as one of the main limitations of sediment toxicity tests is disruption of sediment geochemistry during sampling, handling and preservation. The effects of storage on the estimation of marine sediment toxicity to Crassostrea gigas embryos and larvae were investigated. Three storage methods and four storage periods were compared with three different sediment types contaminated by heavy metals, polycyclic aromatic hydrocarbons (PAHs) and both contaminants. Freezing and freeze-drying considerably increased the toxicity of decanted sediments and their elutriates as compared to the toxicity obtained with fresh sediments. Concerning the elutriates, the toxicity found with frozen and freeze-dried sediments was correlated with DOC, ammonia and PAH contents. However, the toxicity of fresh sediments kept at 4 degrees C increased with increasing duration of storage and was also correlated with the amount of ammonia in the elutriates.     

Arsenic in marine sediments from French Mediterranean ports: Geochemical partitioning,bioavailability and ecotoxicology

This work investigates arsenic mobility, bioavailability and toxicity in marine port sediments using chemical sequential extraction and laboratory toxicity tests. Sediment samples were collected from two different Mediterranean ports, one highly polluted with arsenic and other inorganic and organic pollutants (Estaque port (EST)), and the other one, less polluted, with a low arsenic content (Saint Mandrier port (SM)). Arsenic distribution in the solid phase was studied using a sequential extraction procedure specifically developed for appraising arsenic mobility in sediments. Toxicity assessment was performed on sediment elutriates, solid phases and aqueous arsenic species as single substance using the embryo-toxicity test on oyster larvae (Crassostrea gigas) and the Microtox test with Vibrio fischeri. Toxicity results showed that all sediment samples presented acute and sub-chronic toxic effects on oyster larvae and bacteria, respectively. The Microtox solid phase test allow to discriminate As-contaminated samples from the less contaminated ones, suggesting that toxicity of whole sediment samples is related to arsenic content. Toxicity of dissolved arsenic species as single substance showed that Vibrio fischeri and oyster larvae are most sensitive to As(V) than As(III). The distribution coefficient (Kd) of arsenic in sediment samples was estimated using results obtained in chemical sequential extractions. The Kd value is greater in SM (450 L kg^?1) than in EST (55 L kg^?1), indicating that arsenic availability is higher for the most toxic sediment sample (Estaque port). This study demonstrates that arsenic speciation play an important role on arsenic mobility and its bioavailability in marine port sediments.     

SITE Demonstration of the CF Systems Organic Extraction Process

The CF Systems Organic Extraction Process was used to remove PCBs from contaminated sediment dredged from the New Bedford Harbor. This work was done as part of a field demonstration under EPA’s Superfund Innovative Technology Evaluation (SITE) program. The purpose of the SITE program is to provide an independent and objective evaluation of innovative waste remediation processes. The purpose of this paper is to present the results of the SITE demonstration of this technology. Results of the demonstration tests show that the system, which uses liquefied propane, successfully removed PCBs from contaminated sediments in New Bedford Harbor. Removal efficiencies for all test runs exceeded 70 percent. Some operational problems occurred during the demonstration which may have affected the efficiency with which PCBs were removed from the dredged sediment. Large amounts of residues were generated from this demonstration project. Costs for using this process are estimated to be between $150/ton and $450/ton.     

Development of models for predicting toxicity from sediment chemistry by partial least squares-discriminant analysis and counter-propagation artificial neural networks

There is strong interest in developing tools to link chemical concentrations of contaminants to the potential for observing sediment toxicity that can be used in initial screening-level sediment quality assessments. This paper presents new approaches for predicting toxicity in sediments, based on 10-day survival tests with marine amphipods, from sediment chemistry, by means of the application of Partial Least Squares-Discriminant Analysis (PLS-DA) and Counter-propagation Artificial Neural Networks (CP-ANNs) to large historical databases of chemical and toxicity data. The exploration of the internal structure of the developed models revealed inherent limitations of predicting toxicity from common chemical analyses of bulk contaminant concentrations. However, the results obtained in the validation of these models combined relevant values of non-error classification rate, sensitivity and specificity of, respectively, 76, 87 and 73% with PLS-DA and 92, 75 and 97% with CP-ANNs, outperforming the results reported for previous approaches.     

SITE demonstration of the CF systems organic extraction process

The CF Systems Organic Extraction Process was used to remove PCBs from contaminated sediment dredged from the New Bedford Harbor. This work was done as part of a field demonstration under EPA's Superfund Innovative Technology Evaluation (SITE) program. The purpose of the SITE program is to provide an independent and objective evaluation of innovative waste remediation processes. The purpose of this paper is to present the results of the SITE demonstration of this technology. Results of the demonstration tests show that the system, which uses liquefied propane, successfully removed PCBs from contaminated sediments in New Bedford Harbor. Removal efficiencies for all test runs exceeded 70 percent. Some operational problems occurred during the demonstration which may have affected the efficiency with which PCBs were removed from the dredged sediment. Large amounts of residues were generated from this demonstration project. Costs for using this process are estimated to be between $150/ton and $450/ton.