EFFECTS OF AN OIL SPILL ON SOIL PHYSICO-CHEMICAL PROPERTIES OF A SPILL SITE IN A TYPIC PALEUDULT OF MIDWESTERN NIGERIA

Physico-chemical analysis of soil samples at an oil spill sitein a Typic Paleudult of midwestern Nigeria showed that thetotal hydrocarbon content of top soil layers ranged from 0.6to 12.6 ppm in the heavy impact zone and the oil hadpenetrated to a depth of 9.2 m. Hydrocarbon concentration inthe medium impact zone ranged from 0.36 ppm while hydrocarbonswere not detected in 80% of samples from the unimpactedreference zone. Measurement of heavy metal concentrations inthe soil revealed a significant build-up (p< 0.05) of lead,iron and zinc in the heavy impact zone. Other parametersincluding electrical conductivity, exchangeable cations,available phosphorus and total nitrogen in impacted soils werecomparatively low while the total organic carbon was high,compared with the reference site. Textural class of soil fromthe different depths showed a predominantly brown sand at thetopsoil, loamy sand and grey fine sand at medium depths andred sandy clay at greater depths.     

Effects of an oil spill on soil physico-chemical properties of a spill site in the Niger Delta Area of Nigeria

Physico-chemical analysis of soil samples at an oil spill site in the Niger Delta Area of Nigeria showed that the total hydrocarbon content of top soil layers ranged from 0.8 to 12.4 ppm in the heavy impact zone and the oil had penetrated to a depth of 7.2 m. Hydrocarbon concentration in the medium impact zone ranged from 0.02 to 0.40 ppm while hydrocarbons were not detected in 75% of samples from the unimpacted reference zone. Measurement of heavy metal concentrations in the soils revealed a significant build-up (p<0.05) of lead, iron and zinc in the heavy impact zone. Other parameters including electrical conductivity, exchangeable cations, available phosphorus and total nitrogen in impacted soils were comparatively low while the total organic carbon was high, compared with the reference site. Textural class of soil from the different depths showed a predominantly brown sand at the top soil, loamy sand at medium depths and grey coarse sand at greater depths.     

Effects of an Oil Spill on Soil Physico-Chemical Properties of a Spill Site in a Typic Udipsamment of the Niger Delta Basin of Nigeria

Physico-chemical analysis of soil samples at an oil spill site in a Typic Udipsamment of the Niger Delta Basin of Nigeria showed that the total hydrocarbon content of top soil layers ranged from 18.6 to 23.6 ppm in the heavy impact zone and the oil had penetrated to a depth op 8.4 m. The concentration of hydrocarbons in the medium impact zone ranged from 10.04 to 10.38 ppm while hydrocarbons were not detected in 85% of samples from the unimpacted reference zone. Heavy metal concentration measurements in the soil revealed a significant build-up (P < 0.05) of lead, copper and zinc in the heavy impact zone. Other quality parameters including electrical conductity, exchangeable cations, total nitrogen and available phosphorus in impacted soils were relatively low, while the total organic carbon was high compared with the reference site. Textural class of soil from the different depths showed a predominantly brown sand at the topsoil, loamy sand and grey coarse sand at medium depths, and grey coarse sand and greyish sandy clay at greater depths.     

乌鲁木齐冬季气溶胶散射吸收特性

采用积分式浑浊度仪于2012年1月在乌鲁木齐市中区和市北区对气溶胶的散射系数和吸收系数进行连续观测,分析了市中区与市北区气溶胶散射系数和吸收系数的变化特征,结合同期的相关气象资料对变化特征进行了讨论。结果表明,市中区和市北区气溶胶的散射系数、吸收系数具有相同的变化趋势。总体上呈"W"型;峰值分别出现在0:00和12:00前后,谷值则出现在5:00和17:00前后。散射系数远大于吸收系数,说明大气气溶胶的消光作用主要由散射作用完成。相对湿度与散射系数、吸收系数不具有显著相关性,而风速对散射系数、吸收系数影响较大,且对市北区的影响大于市中区。     

Comparison of EC and BC and evaluation of dust aerosol contribution to light absorption in Xi'an, China

The concentrations of EC, BC and dust aerosols were determined for atmospheric samples collected from an observation station in Xi'an, China. The results show that the averaged correlation coefficient between EC and BC was founded to be 0.72 with 0.81 (n = 49) in autumn, 0.70 (n = 112) in winter and 0.69 (n = 57) in spring, respectively. Absorption coefficients of dust aerosol were estimated to be 2.7 m² g⁻¹ in autumn and 4.4 m² g⁻¹ in winter. The comparison of absorption coefficients of dust aerosol with those of BC implies that BC is the principal light-absorbing aerosol over Xi'an atmosphere. By combining thermal analysis of elemental carbon and dust contents in the aerosol samples, however, the fraction of dust absorption to total light absorption is estimated to be 19% in autumn and 31% in winter, respectively.     

Inter-relations between biological and physicochemical factors in a database for a shallow estuarine system

This paper examines data obtained since 1976 in Peel Inlet and the Harvey Estuary, a shallow estuarine system in Western Australia, which has nuisance growths of macroalgae and seasonal blooms of the cyanobacterium (blue-green alga)Nodularia spumigena. Data collected at the same sites at weekly or fortnightly intervals include phytoplankton (chlorophylla), water nutrients (nitrogen and phosphorus), salinity, temperature and light penetration. Seasonally, the biomass of macroalgae has been measured at a number of sites and used to estimate total biomass.The data are characterised by large season-to-season differences, attributable to the seasonality and volume of river flow. The information has been used to relate the magnitude of summer blue-green algal blooms to the winter loading of phosphorus from the surrounding catchment, and the magnitude of macroalgal biomass to light penetration through the water column.     

Accumulation of Tobacco mosaic virus (TMV) at different depths clay and loamy sand textural soils due to tobacco waste application

The effects of tobacco waste (TW) application to the soil surface on the accumulation of Tobacco mosaic virus (TMV) in clay and loamy sand textural soils at various depths were investigated in two different fields. The tobacco waste had been found to be infected with TMV. Eighteen months after TW application to the soil surface, soils were sampled at 20 cm intervals through to 80 cm depth. The DAS-ELISA method was performed to determine infection of soil with TMV. The viruses persisted in clay soil for a long period compared with loamy sand soil. There was no accumulation of TMV at any depth of loamy sand soil in Experimental Field 2. TMV adsorption to soil particles in 0-60 cm depth of clay soil was determined in all TW treatments in Experimental Field 1. The highest ELISA Absorbance (A405) values in all treatments were determined in the 20-40 cm soil depth that had the highest clay content. ELISA A405 values of TMV at different depths of clay soil gave significant correlations with clay content (r = 0.793**), EC values (r = 0.421**) and soil pH (r = -0.405**). Adsorption of TMV to net negatively charged clay particle surfaces increased with increasing EC values of soil solution. Decreasing soil pH and infiltration rate increased adsorption of TMV to clay particles. Higher infiltration rate and lower clay content in loamy sand soil caused leaching of TMV from the soil profile.     

Evaluation of a novel passive sampling technique for monitoring volcanogenic hydrogen sulfide

A novel, low-cost passive sampling procedure for monitoring of volcanogenic hydrogen sulfide is reported. The technique is based on absorption of H2S onto treated sections of photographic paper, which are housed in plastic film canisters during exposure. The H2S reacts with silver halide in the photographic paper, causing a colour-change reaction from white, through brown, to black, depending on concentration of atmospheric H2S. The sampler is sensitive to < 30 ppb to approximately 1000 ppb of H2S. Here we present results from a series of optimization and quantification experiments. An active sampling procedure for rapid H2S measurement is also reported, based on absorption of H2S onto Whatman No. 41 cellulose filters treated with silver nitrate, and was shown to be quantitative using a single filter at flow rates <1.0 L min(-1) for collection of <200 microg of sulfide (as H2S). Determination of sulfide collected on the substrates was performed using a rapid flow-injection technique based on the fluorescence quenching of fluorescein mercuric acetate (FMA) by sulfide. This was optimized at a FMA concentration of 8 mg L(-1), at which 100% quenching was obtained at a solution sulfide concentration of 3 mg L(-1).     

Comparison of soil solution sampling techniques to assess metal fluxes from contaminated soil to groundwater

The unsaturated zone plays a major role in elemental fluxes in terrestrial ecosystems. A representative chemical analysis of soil pore water is required for the interpretation of soil chemical phenomena and particularly to assess Trace Elements (TEs) mobility. This requires an optimal sampling system to avoid modification of the extracted soil water chemistry and allow for an accurate estimation of solute fluxes. In this paper, the chemical composition of soil solutions sampled by Rhizon® samplers connected to a standard syringe was compared to two other types of suction probes (Rhizon®?+?vacuum tube and Rhizon®?+?diverted flow system). We investigated the effects of different vacuum application procedures on concentrations of spiked elements (Cr, As, Zn) mixed as powder into the first 20 cm of 100-cm columns and non-spiked elements (Ca, Na, Mg) concentrations in two types of columns (SiO₂ sand and a mixture of kaolinite?+?SiO₂ sand substrates). Rhizon® was installed at different depths. The metals concentrations showed that (i) in sand, peak concentrations cannot be correctly sampled, thus the flux cannot be estimated, and the errors can easily reach a factor 2; (ii) in sand?+?clay columns, peak concentrations were larger, indicating that they could be sampled but, due to sorption on clay, it was not possible to compare fluxes at different depths. The different samplers tested were not able to reflect the elemental flux to groundwater and, although the Rhizon®?+?syringe device was more accurate, the best solution remains to be the use of a lysimeter, whose bottom is kept continuously at a suction close to the one existing in the soil.     

Occurrence and sorption properties of arsenicals in marine sediments

The content of total arsenic, the inorganic forms: arsenite (As(III)) and arsenate (As(V)), the methylated forms: monomethylarsonic acid and dimethylarsinic acid (DMA), trimethylarsenic oxide, tetramethylarsenonium ion and arsenobetaine was measured in 95 sediment samples and 11 pore water samples from the Baltic Sea near the island of Bornholm at depths of up to 100 m. As(III+V) and DMA were detected in the sediment and As(III+V) was detected in the sediment pore water. Average total As concentration of 10.6?±?7.4 mg/kg dry matter (DM) in the sediment corresponds to previously reported values in the Baltic Sea and other parts of the world. Existing data for on-site measurements of sorption coefficients (Kd) of arsenicals in marine and freshwater sediments show large variability from <1 to >1,000 L/kg. In this work, calculated sorption coefficients (Kd and Koc) for As(III+V) showed significant correlation with depth, dissolved oxygen (DO), salinity and sediment classification; for depths <70 m, salinity <11 %, DO >9 mg/L and sand/silt/clay sediments the Kd was 118?±?76 L/kg DM and for depths >70 m, salinity >11 %, DO?<?9 mg/L and muddy sediments the Kd was 513?±?233 L/kg DM. The authors recommend using the found Kd value for arsenic in marine sediments when conditions are similar to the Baltic Sea. At locations with significant anthropogenic point sources or where the local geology contains volcanic rock and sulphide mineral deposits, there may be significantly elevated arsenic concentrations, and it is recommended to determine on-site Kd values.     

Summer time haze characteristics of the urban atmosphere of Gwangju and the rural atmosphere of Anmyon, Korea

An extensive visibility monitoring was carried out simultaneously in the urban area of Gwangju and the rural area of Anmyon, Korea. This study examines patterns of visibility impairment and haze-forming pollutant concentrations on both sites resulting from natural and anthropogenic sources of gases and particles. Optical visibility measurements by a transmissometer, a nephelometer and an aethalometer provide aerosol light extinction, scattering, and absorption coefficients for both sites. In order to investigate the physico-chemical characteristics of atmospheric aerosols, aerosol samples were collected by various aerosol samplers at GJVMS (Gwangju Visibility Monitoring Station) and at KGAWO (Korea Global Atmosphere Watch Observatory), respectively. In addition, haze characteristics causing visibility impairment at those two sites were analyzed to obtain source contributions by regionally transported aerosols using grid analysis and display system (GrADS) from NECP reanalysis data. During the intensive monitoring period, ammonium sulfate was dominantly responsible for the fine particle mass loading at GJVMS, whereas organic carbon was the largest contributor at KGAWO. Light scattering by particles accounted for 52.8 to 81.3% of the range at the urban site, GJVMS and for 72.1 to 94.2% of the range at the rural site, KGAWO. Light absorption by the EC and NO₂ was between 14.5 and 34.8% at GJVMS, which was higher than the observed 1.1 ∼ 6.8% at KGAWO, respectively. Light scattering by aerosol was higher in the rural area than in the urban area. And organic carbon concentration was observed to be significantly higher than the concentration of elemental carbon at KGAWO. These haze-forming carbonaceous particles originate from anthropogenic pollutants at the urban atmosphere but they can be produced by natural environments such as marine and forest at the rural atmosphere.     

南京北郊气溶胶散射特性观测研究

南京北郊是重工业区,空气污染严重。该文利用浊度仪对大气气溶胶散射系数进行了四季观测,研究了该区气溶胶散射系数、后向散射比、质量散射系数及散射系数与能见度的关系,结果表明,观测期间散射系数波动较大,平均值为344.84 Mm^-1,标准差为215.99 Mm^-1,散射系数季节差异明显,主要受气象条件和外界污染排放的影响;后向散射比平均值为0.139,春季变化剧烈,夏、秋、冬季在波动中缓慢上升,大气中细粒子污染严重且含量有增加的趋势;散射系数与PM_2.5质量浓度相关系数达到0.91,质量散射系数平均值为1.87m²/g;散射系数与能见度之间存在-0.66的相关性,两者呈负幂函数关系。     

Statistical evaluation of photon count rate data for nanoscale particle measurement in wastewaters

The dynamic light scattering (DLS) technique can detect the concentration and size distribution of nanoscale particles in aqueous solutions by analyzing photon interactions. This study evaluated the applicability of using photon count rate data from DLS analyses for measuring levels of biogenic and manufactured nanoscale particles in wastewater. Statistical evaluations were performed using secondary wastewater effluent and a Malvern Zetasizer. Dynamic light scattering analyses were performed equally by two analysts over a period of two days using five dilutions and twelve replicates for each dilution. Linearity evaluation using the sixty sample analysis yielded a regression coefficient R(2) = 0.959. The accuracy analysis for various dilutions indicated a recovery of 100 ± 6%. Precision analyses indicated low variance coefficients for the impact of analysts, days, and within sample error. The variation by analysts was apparent only in the most diluted sample (intermediate precision ~12%), where the photon count rate was close to the instrument detection limit. The variation for different days was apparent in the two most concentrated samples, which indicated that wastewater samples must be analyzed for nanoscale particle measurement within the same day of collection. Upon addition of 10 mg l(-1) of nanosilica to wastewater effluent samples, the measured photon count rates were within 5% of the estimated values. The results indicated that photon count rate data can effectively complement various techniques currently available to detect nanoscale particles in wastewaters.     

210Po bioaccumulation in coastal sand dune wild legumes--Canavalia spp. of southwest coast of India

In view of considerable natural background radioactivity reported from southwest coast of India, the current study documents bioaccumulation of 210Po in two dominant coastal sand dune perennial mat-forming wild legumes, Canavalia cathartica and C. maritima. Root, stem, leaf, mature beans, dry seeds and rhizosphere sand were analyzed for 210Po concentration. 210Po activity decreased in the order of leaves > roots > seeds > stems > beans. The highest 210Po activity was recorded in rhizosphere sand samples (5.78-5.88 Bq kg(-1)) followed by the leaf samples (3.27-3.07 Bq kg(-1)), while it was lowest in mature beans (0.13-0.20 Bq kg(-1)). 210Po activities or tissue moisture between plant species were not significantly different (p > 0.05; t-test). But 210Po activity vs. moisture differed significantly in all tissues (p = 0.0001), vegetative tissues (root, stem and leaf) (p = 0.0016), seeds (p = 0.0393) and proteins in seeds (p = 2.355 x 10(-6)) indicating the importance of moisture and protein in 210Po accumulation. Although 210Po has affinity for proteins, it did not concentrate too much in seed proteins of Canavalia. Concentration of 210Po in mature beans is at safe levels as fisher folk only consume tender pods occasionally. 210Po activity in Canavalia is compared with other plant materials. As the landraces of C. cathartica and C. maritima are distributed throughout pantropical coastal areas, the current study emphasizes on considering them as bioindicators to monitor 210Po in coastal sand dune biomes and in turn the health of coastal population.     

Twenty-four Hour in situ Monitoring of Oxygen Production and Respiration of the Colonial Zoanthid Palythoa

The rates of oxygen production and respiration of the colonial zoanthid of the genus Palythoa were measured in situ at a depth of 3.4m (reef-edge) using an automated respirometer. The respirometer recorded changes in oxygen concentration of four samples of Palythoa enclosed in separate perspex chambers concurrently with light intensity (irradiance) readings every 20 seconds for 24 hours. Photosynthetic parameters (Pm(gross), Rd and Ik) were estimated from photosynthesis-irradiance (PI) curves generated for each of the four samples. Average instantaneous maximum gross photosynthetic (Pm(gross)) and respiration (Rd) rates obtained for Palythoa were 12.50µmo2l cm-2h-1 and - 4.24µmolO2cm-2h-1, giving a Pm(gross)/(-Rd) ratio of 2.92. The net 24 hour production (Pn24) at 3.4m, estimated by integrating the photokinetic parameters over 7 days of light data, was negative, resulting in a daily gross photosynthesis to respiration [Pg24/(-Rd24)] ratio of 0.77, while estimated 24 hour productivity at 1.4m gave a ratio of 1.13. This suggests that Palythoa would be able to sustain positive production at 1.4m but not at 3.4m.     

Spatial variability of salinity and alkalinity of a field having salination risk in semi-arid climate in northern Turkey

Spatial variability of salinity and alkalinity is important for site-specific management since they are the most important factors influencing soil quality and agricultural production. The objectives of this study were to analyze spatial variability in salinity and alkalinity and some soil properties affecting salinity and alkalinity, using classical statistics and geostatistical methods, in an irrigated field with low-quality irrigation water diverted from drainage canals. A field of 5 da was divided into 10 m x 10 m grids (5 lines in the east-west direction and 10 lines in the north-south direction). The soil samples were collected from three depths (0-30, 30-60 and 60-90 cm) at each grid corner. The variation coefficients of OM and sand contents were higher than other soil properties. OM had the maximum variability, with a mean of 1.63% at 0-30 cm depth and 0.71% at 30-60 cm depth. Significant correlations occurred between ESP, EC and each of Ca, Mg, K and CaCO(3) contents of the soils (p<0.01). Experimental semivariograms were fitted to spherical and gaussian models. All geostatistical range values were greater than 36 m. The soil properties had spatial variability at small distances at 60-90 cm depth. EC was variable within short distances at 30-60 cm depth. The nugget effect of ESP increased with soil depth. Kriged contour maps revealed that soils had a salinisation and alkalisation tendency at 60-90 cm depth based on spatial variance structure of the EC and ESP values. Spatial variability in EC and ESP can depend on ground water level, quality of irrigation water, and textural differences.     

Geotechnical assessment of road failure and slope monitoring along Nsukka-Adoru-Idah highway,Southeastern Nigeria

The quality of highway pavement is greatly influenced by the subgrade materials, the general geology of the area, and the materials used for construction. Investigation into the 75-km Nsukka-Adoru-Idah highway revealed that the pavement was underlain by three lithological units—Imo, Nsukka, and Ajali formations. The geotechnical evaluation carried out in the study includes the particle size distribution, Atterberg limit, specific gravity, compaction tests, and California bearing ratio (CBR). The base course has clay/silt (7–14%), fine sand (1–4%), medium sand (6–13%), and coarse sand (65–86%), while the subgrade presented clay/silt (74–82%), fine sand (6–9%), medium sand (10–17%), and coarse sand (1–3%). The average specific gravity results for the studied base course and subgrades are 2.58 and 2.52. Liquid limit (LL) result ranges from 27 to 60%, while plastic limit (PL) ranges between 17 and 24%, and plasticity index (PI) ranges from 5 to 39%. The maximum dry density (MDD) result ranges from 1.70 to 2.10 mg/m³, while the optimum moisture content (OMC) for the samples ranges between 14.1 and 18.0%. The CBR result for soaked and unsoaked samples ranges from 37 to 74 and 48 to 83%, respectively. The low unsoaked CBR (<80%) and high Atterberg limits (LL > 30% and PI > 12%) failed the stipulated Nigerian standard, signifying the need for stabilization. A geotechnical model of a highway road cut generated a factor of safety of 1.45, indicating possibility of slope failure.     

Comparability between PM2.5 and particle light scattering measurements

Particle light scattering and PM_2.5 (particles with aerodynamic diameters less than 2.5 m) concentration data from air quality studies conducted over the past ten years wereexamined. Fine particle scattering efficiencies were determinedfrom statistical relationships among measured light scattering and fine and coarse mass concentrations. The resulting fine particle scattering efficiencies ranged from 1.7 m² g^-1at Meadview in the Grand Canyon to over 5 m² g^-1 in Mexico City. Most of the derived fine scattering efficiencieswere centered around 2 m² g^-1, which is considerablylower than most values reported from previous studies.     

Assessment of the Heavy Metal Pollution Effects on the Soil Respiration in the Baix Llobregat (Catalonia, NE Spain)

A main goal of investigations is to determine could a soilrespiration be an indicator of the soil pollution. In this case a measured levelof the soil oxygen consumption depends of its pollution. It alsomeans that the pollution reduces biological processes in edaphon.Investigated soil samples were taken from polluted andnon-polluted places in the Baix Llobregat near Barcelona (Catalonia, NE Spain). Soil samples were taken from the top ofsoil (0–5 cm) without a litter. Soil analysis were done, determining percentage shares of coarsefragments, coarse sand, fine sand, coarse silt, fine silt, clay,CaCO₃, organic matter as well as water pH and conductivityCE (1:5 [mS cm^-1]). Also were determined (in mg kg^-1)quantities of heavy metals, as Fe, Al, Mn, Zn, Cr, Ni, V, Cu, Cd, Pb.The soil respiration was investigated in temperatures15 and 30 °C and with controlled humidity.The respiration in 30 °C is number of times greater thenin 15 °C both for polluted and non-polluted soils.Particularly high coefficients of correlation between the soilrespiration and soil pollution in polluted soils were obtainedfor Pb: r = 0.75 in 15 °C and r = 0.98 in30 °C; for Ba: 0.90 and 0.57; for V: 0.99 and 0.81. In non-polluted soils highest correlation coefficients are for Pb: r = 0.70 in 15 °C; Fe: 0.60 and 0.72; Al: 0.68 and0.64; Mn: 0.51 and 0.66; Ba: 0.63 and 0.61; Cr: 0.94 and0.70; Ni: 0.64 and 0.65; Cu: 0.69 and 0.48; as well as V: 0.62in 15 °C; and Cd: 0.69 in 15 °C.This way the soil respiration could be a good indicator of the soil pollution.     

Antimony speciation in soil samples along two Austrian motorways by HPLC-ID-ICP-MS

Distribution of antimony and its inorganic species in soil samples along two traffic routes (A14, Rankweil and S36, Knittelfeld) in Austria was determined, since vehicle emissions are an important anthropogenic source of Sb in soil. The samples were taken along three parallel lines at about 0.2, 2 and 10 m distances from the edge of the road and in two depths range (0-5 and 5-10 cm from the soil surface). The optimized extraction was carried out using 100 mmol L(-1) citric acid at pH 2.08 applying an ultrasonic bath for 45 min at room temperature. Speciation analyses were done using on-line isotope dilution after a chromatographic separation of Sb species. Results of the two traffic routes confirmed significant accumulations of Sb at surface (0-5 cm depth) exceeding the natural background values by more than ten times at the S36 or four times at the A14. Concentrations of the extractable inorganic species decreased to natural background levels within a few meters from the edge of the traffic lane. The predominant Sb species was Sb(V). The Sb(III) concentrations at 5-10 cm depths range are nearly constant with distance from the edges of the two roads. Magnetic susceptibility data of all soil samples show the same distribution pattern as Sb and Sb(V) concentrations along the two traffic roads with an excellent correlation. This is an evidence for an anthropogenic source of Sb such as abrasions of motor vehicles surfaces or braking linings. The input of Sb and its inorganic species at one of the sampling sites (Knittelfeld) in samples taken in 2002 and in those taken recently (2005) was monitored. An increase in Sb (>or=30%), Sb(v)(>or=51%) and Sb(iii)(>or=10%) concentrations was only observed near the edge (相似文献