Environmentally safe sewage sludge disposal: the impact of liming on the behaviour of Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Zn

Dewatered sewage sludge containing relatively high total concentrations of Cr (945 micrograms ml-1), Cu (523 micrograms ml-1), Ni (1186 micrograms ml-1) and Zn (2950 micrograms ml-1) was treated with quicklime and sawdust for sludge disinfection and post-stabilisation. The mobility of the heavy metals in the sludge samples was assessed by applying a modified five-step Tessier sequential extraction procedure. Water was added as a first step for estimation of the proportion of the easily soluble metal fractions. To check the precision of the analytical work the concentrations of heavy metals in steps 1-6 of the extraction procedure were summed and compared to the total metal concentrations. The mass balance agreed within +/- 3% for Cd, Cu, Cr, and Zn and within +/- 5% for Ni, Pb, Fe and Mn. Data from the partitioning study indicate that in the lime-treated sludge at a pH of 12 the mobility of Cu and Ni notably increased with the solubilisation of these metals from their organic and/or carbonate and Fe and Mn oxide and hydroxide fractions, respectively. Liming slightly decreased the proportion of other heavy metals in the easily soluble fractions while its impact on the partitioning between other sludge phases was almost insignificant. Due to the increased solubility of Ni and Cu as well as potential Cr oxidation at high pH, liming cannot be recommended for sludge disinfection. Addition of sawdust did not change the heavy metal partitioning.     

离子色谱法同时测定酸雨中的钠、铵、钾、镁、钙

阐述了离子色谱法测定酸雨中的钠、铵、钾、镁、钙含量的方法和步骤。结果表明,各元素的检出限均低于0.02 mg/L,加标回收率为90%~110%,相对标准偏差均低于1%,结果令人满意。该方法可同时测定酸雨中的5种阳离子,并且操作便捷,值得推广与应用。     

Characterization and Identification of the Sources of Chromium, Zinc, Lead, Cadmium, Nickel, Manganese and Iron in Pm10 Particulates at the Two Sites of Kolkata, India

Monitoring of ambient PM₁₀ (particulate matter which passes through a size selective impactor inlet with a 50% efficiency cut-off at 10 μm aerodynamic diameter) has been done at residential (Kasba) and industrial (Cossipore) sites of an urban region of Kolkata during November 2003 to November 2004. These sites were selected depending on the dominant anthropogenic activities. Metal constituents of atmospheric PM₁₀ deposited on glass fibre filter paper were estimated using Inductively Coupled Plasma Atomic Emission Spectrometer (ICP-AES). Chromium (Cr), zinc (Zn), lead (Pb), cadmium (Cd), nickel (Ni), manganese (Mn) and iron (Fe) are the seven toxic trace metals quantified from the measured PM₁₀ concentrations. The 24 h average concentrations of Cr, Zn, Pb, Cd, Ni, Mn and Fe from ninety PM₁₀ particulate samples of Kolkata were found to be 6.9, 506.1, 79.1, 3.3, 7.4, 2.4 and 103.6 ng/m³, respectively. The 24 h average PM₁₀ concentration exceeded national ambient air quality standard (NAAQS) as specified by central pollution control board, India at both residential (Kasba) and industrial (Cossipore) areas with mean concentration of 140.1 and 196.6 μg/m³, respectively. A simultaneous meteorology study was performed to assess the influence of air masses by wind speed, wind direction, rainfall, relative humidity and temperature. The measured toxic trace metals generally showed inverse relationship with wind speed, relative humidity and temperature. Factor analysis, a receptor modeling technique has been used for identification of the possible sources contributing to the PM₁₀. Varimax rotated factor analysis identified four possible sources of measured trace metals comprising solid waste dumping, vehicular traffic with the influence of road dust, road dust and soil dust at residential site (Kasba), while vehicular traffic with the influence of soil dust, road dust, galvanizing and electroplating industry, and tanning industry at industrial site (Cossipore).     

Prediction of the solubility of zinc, copper, nickel, cadmium, and lead in metal-contaminated soils

Risk assessment of metal-contaminated soil depends on how precisely one can predict the solubility of metals in soils. Responses of plants and soil organisms to metal toxicity are explained by the variation in free metal ion activity in soil pore water. This study was undertaken to predict the free ion activity of Zn, Cu, Ni, Cd, and Pb in metal-contaminated soil as a function of pH, soil organic carbon, and extractable metal content. For this purpose, 21 surface soil samples (0–15 cm) were collected from agricultural lands of various locations receiving sewage sludge and industrial effluents for a long period. One soil sample was also collected from agricultural land which has been under intensive cropping and receiving irrigation through tube well water. Soil samples were varied widely in respect of physicochemical properties including metal content. Total Zn, Cu, Ni, Cd, and Pb in experimental soils were 2,015?±?3,373, 236?±?286, 103?±?192, 29.8?±?6.04, and 141?±?270 mg kg^?1, respectively. Free metal ion activity, viz., pZn²⁺, pCu²⁺, pNi²⁺, pCd²⁺, and pPb²⁺, as estimated by the Baker soil test was 9.37?±?1.89, 13.1?±?1.96, 12.8?±?1.89, 11.9?±?2.00, and 11.6?±?1.52, respectively. Free metal ion activity was predicted by pH-dependent Freundlich equation (solubility model) as a function of pH, organic carbon, and extractable metal. Results indicate that solubility model as a function of pH, Walkley–Black carbon (WBC), and ethylenediaminetetraacetic acid (EDTA)-extractable metals could explain the variation in pZn²⁺, pCu²⁺, pNi²⁺, pCd²⁺, and pPb²⁺ to the extent of 59, 56, 46, 52, and 51 %, respectively. Predictability of the solubility model based on pH, KMnO₄-oxidizable carbon, and diethylenetriaminepentaacetic acid-extractable or CaCl₂-extractable metal was inferior compared to that based on EDTA-extractable metals and WBC.     

Quantifying the Effects of Forest Management Strategies on the Production of Forest Values: Timber,Carbon, Oxygen,Water, and Soil

Forest management practices alter forest structure quantified with ecosystem characteristics and values. In this paper, we utilized a forest management simulation model to assess the effects of three forest management strategies focusing on timber production, carbon sequestration, oxygen production, soil erosion, and water production of a forest management unit in Turkey. A forest simulation model “ETÇAPSimülasyon” was developed and used to project forest ecosystem development over 100 years under three forest management policies of timber-oriented forest management (TFM), multipurpose forest management (MFM), and no intervention (NI). The results showed that TFM strategy produced more timber and its net present value than MFM and NI strategies did. The amount of carbon sequestration and oxygen production potential was also found to be the highest with TFM strategy than with the MFM and NI strategies. Compared with the other strategies, however, NI strategy produced the highest amount of water production and soil losses over the planning horizon. The effects of a forest management strategy depend mainly on the initial forest structure, the rate of development and the level of forest management interventions. Therefore, forest dynamics under various management strategies should be explained before the final management decision. Understanding long-term effects of any management strategies on forest structure will provide the basis for better reaching the management objectives.     

Concentrations of Arsenic, Cadmium, Copper, Lead, Selenium, and Zinc in Fish from the Mississippi River Basin, 1995

Fish were collected in late 1995 from 34 National Contaminant Biomonitoring Program (NCBP) stations and 12 National Water Quality Assessment Program (NAWQA) stations in the Mississippi River basin (MRB), and in late 1996 from a reference site in West Virginia. The NCBP sites represented key points (dams, tributaries, etc.) in the largest rivers of the MRB. The NAWQA sites were typically on smaller rivers and were selected to represent dominant land uses in their watersheds. The West Virginia site, which is in an Eastern U.S. watershed adjacent to the MRB, was selected to document elemental concentrations in fish used for other aspects of a larger study and to provide additional contemporaneous data on background elemental concentrations. At each site four samples, each comprising (nominally) 10 adult common carp (Cyprinus carpio, 'carp') or black bass (Micropterus spp., 'bass') of the same sex, were collected. The whole fish were composited by station, species, and gender for analysis of arsenic (As), lead (Pb), and selenium (Se) by atomic absorption spectroscopy and for cadmium (Cd), copper (Cu), and zinc (Zn) by inductively-coupled plasma emission spectroscopy. Concentrations of most of the elements examined were lower in both carp and bass from the reference site, a small impoundment located in a rural area, than from the NCBP and NAWQA sites on rivers and larger impoundments. In contrast, there were few overall differences between NCBP sites NAWQA sites. The 1995 results generally confirmed the continued weathering and re-distribution of these elemental contaminants in the MRB; concentrations declined or were unchanged from 1984-1986 to 1995 at most NCBP sites, thus continuing two-decade trends. Exceptions were Se at Station 77 (Arkansas R. at John Martin Reservoir, CO), where concentrations have been elevated historically and increased slightly (to 3.8-4.7 microg g-(1) in bass and carp); and Pb, Cd, and Zn at Station 67 (Allegheny R. at Natrona, PA), where levels of these metals were high in the past and increased from 1986 to 1995.     

Monitoring the Conservation of Grassland Habitats, Prairie Ecozone, Canada

The Prairie Ecozone contains 5% of Canada's land area and represents 16% of the Great Plains of North America. Current estimates indicate that 25–30% of original Canadian grassland habitats remain, largely concentrated in southeastern Alberta and southwestern Saskatchewan with fragments distributed throughout southern Manitoba. The size, distribution and condition of native grasslands serve as valuable indicators of the ecological integrity and the sustainability of those landscape types. With so little native grasslands remaining, areas that conserve grasslands serve as core sites for indicators such as gaps in ecosystem and wildlife habitat protection, i.e. which ecosystems are well-represented, poorly represented or have no representation. Such gap analyses helps to determine where protection efforts need to be placed in the future. Overall, about 3.5% of the Prairie Ecozone of Canada is under some form of conservation area status. This paper reports, relative to the ecoregions and political jurisdictions of the Prairie Ecozone, on the amount and distribution of various types of conservation areas and native grasslands. Relationships between the occurrence of conservation areas and grasslands are presented. Implications for conservation area planning and management are discussed within regional, national and international contexts. The issue of which characteristics of conservation areas should be assessed and monitored to address conservation objectives for sustainability is also discussed.     

Mercury, cadmium, lead, and selenium in fish from a Norwegian fjord and off the coast, the importance of sampling locality

Hepatic levels of mercury, cadmium, lead, and selenium and levels of mercury and selenium in muscle tissue were analysed in tusk from the Nordfjord in Norway. With the exception of selenium in the muscle tissue, the metal levels were significantly higher in the fjord fish than in fish caught off the coast. No local source is known to explain the difference in levels, and this indicates that the fjord efficiently accumulates atmospheric contaminants. The present results demonstrate the importance of sampling area when determining levels of metals in marine organisms far from point sources. The liver was increasingly used as a storage compartment for mercury and selenium with increasing exposure.     

Assessment of the exposure of two fish species to metals pollution in the Ogun river catchments, Ketu, Lagos, Nigeria

The concentrations of metals (Ca, Cd, Fe, Mn, Pb and Zn) were determined by flame atomic absorption spectrophotometry in water, sediments and fish samples in the Ogun river catchments, Ketu, Lagos, which is an important bird nesting, fishing and drinking water source. The results show that the southern tip bothering the Lagos lagoon is where the highest metal concentrations are found in the fish species (Tilapia sp. and Chrysichthys sp.), whereas the Agboyi creek segment near the lagoon with higher surrounding human population density recorded higher levels of metals in sediments and water samples. The two fish species accumulated different amounts of metals. However, the differences were not statistically different at p < 0.05. There is a significant correlation (p < 0.05) for Cd concentration in water. The concentrations of Pb in sampling points 3 and 4 as well as Cd, Mn and Fe in all six sampling points exceeds the World Health Organization (WHO) limits for drinking water. Levels of metals obtained for sediments are within the range reported for Nigeria’s river sediments. Based on this study, the human risks for heavy metals in the harvested fish species from the Ogun river catchments, Ketu, are low for now as the concentrations were below the recommended Food and Agriculture Organization (FAO) maximum limits for Pb (0.5 mg/Kg), Cd (0.5 mg/Kg), and Zn (30 mg/Kg) in fish.     

Distribution, speciation, and risk assessment of selected metals in the gold and iron mine soils of the catchment area of Miyun Reservoir, Beijing, China

In order to investigate the metal distribution, speciation, correlation and origin, risk assessment, 86 surface soil samples from the catchment area around the Miyun Reservoir, Beijing, including samples from gold and iron mine areas, were monitored for fractions of heavy metal and total contents. Most of the metal concentrations in the gold and iron mine soil samples exceeded the metal background levels in Beijing. The contents of most elements in the gold mine tailings were noticeably higher than those in the iron mine tailings. Geochemical speciation data of the metals showed that the residual fraction dominated most of the heavy metals in both mines. In both mine areas, Mn had the greatest the acid-soluble fraction (F1) per portion. The high secondary-phase fraction portion of Cd in gold mine samples indicated that there was a direct potential hazard to organisms in the tested areas. Multivariate analysis coupled with the contents of selected metals, showed that Hg, Pb, Cr, and Ni in gold mine areas represented anthropogenic sources; Cd, Pb, and Cr in iron mine areas represented industrial sources. There was moderate to high contamination of a few metals in the gold and iron soil samples, the contamination levels were relatively higher in gold mine than in iron mine soils.     

Groundwater quality assessment in the village of Lutfullapur Nawada, Loni, District Ghaziabad, Uttar Pradesh, India

The groundwater quality for drinking, domestic and irrigation in the village Lutfullapur Nawada, Loni, district Ghaziabad, U.P., India, has been assessed. Groundwater samples were collected, processed and analyzed for temperature, pH, conductivity, salinity, total alkalinity, carbonate alkalinity, bicarbonate alkalinity, total hardness, calcium hardness, magnesium hardness, total solids, total dissolved solids, total suspended solids, nitrate-nitrogen, chloride, fluoride, sulfate, phosphate, silica, sodium, potassium, calcium, magnesium, total chromium, cadmium, copper, iron, nickel, lead and zinc. A number of groundwater samples showed levels of electrical conductivity (EC), alkalinity, chloride, calcium, sodium, potassium and iron exceeding their permissible limits. Except iron, the other metals (Cr, Cd, Cu, Ni, Pb, and Zn) were analyzed below the permissible limits. The correlation matrices for 28 variables were performed. EC, salinity, TS and TDS had significant positive correlations among themselves and also with NO (3) (-) , Cl(-), alkalinity, Na(+), K(+), and Ca(2+). Fluoride was not significantly correlated with any of the parameters. NO (3) (-) was significantly positively correlated with Cl(-), alkalinity, Na(+), K(+) and Ca(2+). Chloride also correlated significantly with alkalinity, Na(+), K(+) and Ca(2+). Sodium showed a strong and positive correlation with K(+) and Ca(2+). pH was negatively correlated with most of the physicochemical parameters. This groundwater is classified as a normal sulfate and chloride type. Base-exchange indices classified 73% of the groundwater sources as the Na(+)-SO (4) (2-) type. The meteoric genesis indices demonstrated that 67% of groundwater sources belong to a deep meteoric water percolation type. Hydrochemical groundwater evaluations revealed that most of the groundwaters belong to the Na(+)-K(+)-Cl(-)-SO (4) (2-) type followed by Na(+)-K(+)-HCO (3) (-) type. Salinity, chlorinity and SAR indices indicated that majority of groundwater samples can be considered suitable for irrigation purposes.     

Effect of a reservoir in the water quality of the Reconquista River, Buenos Aires, Argentina

The lower portion of the Reconquista River is highly polluted. However, little is known about the state of the high and middle basins. The aims of this work were to assess the water quality on the high and middle Reconquista River basins and to determinate if the presence of a reservoir in the river has a positive effect on the water quality. We conducted a seasonal study between August 2009 and November 2010 at the mouth of La Choza, Durazno, and La Horqueta streams at the Roggero reservoir—which receives the water from the former streams—at the origin of the Reconquista River and 17 km downstream from the reservoir. We measured 25 physical and chemical parameters, including six heavy metal concentrations, and performed a multivariate statistical analysis to summarize the information and allow the interpretation of the whole data set. We found that the Durazno and La Horqueta streams had better water quality than La Choza, and the presence of the reservoir contributed to the improvement of the water quality, allowing oxygenation of the water body and processing of organic matter and ammonia. The water quality of the Reconquista River at its origin is good and similar to the reservoir, but a few kilometers downstream, the water quality declines as a consequence of the presence of industries and human settlements. Therefore, the Roggero reservoir produces a significant improvement of water quality of the river, but the discharge of contaminants downstream quickly reverses this effect.     

Pollution levels of thiobencarb, propanil, and pretilachlor in rice fields of the muda irrigation scheme, Kedah, Malaysia

The purpose of this study was to investigate the potential risk of pretilachlor, thiobencarb, and propanil pollutants in the water system of the rice fields of the Muda area. The study included two areas that used different irrigation systems namely non-recycled (N-RCL) and recycled (RCL) water. Regular water sampling was carried out at the drainage canals during the weeding period from September to October 2006 in the main season of 2006/2007 and April-May 2007 in off season of 2007. The herbicides were extracted by the solid-phase extraction method and identified using a GC-ECD. Results showed that the procedure for identification of the three herbicides was acceptable based on the recovery test values, which ranged from 84.1% to 96.9%. A wide distribution pattern where more than 79% of the water samples contained the herbicide pollutants was observed at both the areas where N-RCL and RCL water was supplied for the two seasons. During September to October 2006, high weedicide residue concentration was observed at the N-RCL area and it ranged from 0.05 to 1.00 μg/L for pretilachlor and propanil and 10-25 μg/L for thiobencarb. In the case of the area with RCL water, the weedicide residue ranged from 1 to 5 μg/L for pretilachlor and propanil and 10-25 μg/L for thiobencarb. The highest residue level reached was 25-50, 50-100, and 100-200 μg/L for pretilachlor, propanil, and thiobencarb, respectively. During April to May 2007, high residue concentration frequently occurred at the area supplied with N-RCL irrigation water and it ranged from 0.05 to 1.00, 10 to 25, and 25 to 50 μg/L for pretilachlor, propanil, and thiobencarb, respectively. The highest residue level reached was 25-50 μg/L for pretilachlor and 100-200 μg/L for propanil and thiobencarb. There was an accelerated increase in the concentration of the herbicide residues, with the maximum levels reached at the early period of weedicide application, followed by a sharp decrease after the rice fields were completely covered with the rice crop. During the main season of 2006/2007, the concentration of propanil residue gradually rose, although that of the other herbicides declined.     

Lead, arsenic, fluoride, and iron contamination of drinking water in the tea garden belt of Darrang district, Assam, India

Drinking water quality with respect to lead, iron, fluoride, and arsenic has been carried out in and around tea gardens of Darrang district of Assam, India. The district lies between 26°25^′ and 26°55^′ northern latitude and 91°45^′ and 91°20^′ east longitude and covers an area of 3,465.30 km². Twenty-five different sampling stations were selected for the study. Iron, lead, and arsenic were analyzed by using an atomic absorption spectrometer, Perkin Elmer AA 200, while fluoride was measured by the SPADNS method using a UV–VIS spectrometer, Shimadzu 1240 model. The study revealed that the water sources in the area are heavily polluted with lead. Statistical analysis of the data is presented to determine the distribution pattern, localization of data, and other related information. Statistical observations imply non-uniform distribution of the studied parameters with a long asymmetric tail either on the right or left side of the median.     

Occurrence,sources, and ecological risks of PBDEs,PCBs, OCPs,and PAHs in surface sediments of the Yangtze River Delta city cluster,China

Polybrominated diphenyl ethers (PBDEs), organochlorine pesticides (OCPs), polychlorinated biphenyls (PCBs), and polycyclic aromatic hydrocarbons (PAHs) in 25 surface sediments in three cities (Nantong, Wuxi, and Suzhou) in the Yangtze River Delta, eastern China were measured. The mean concentrations were 378, 45.8, 1.98, 4,002 ng/g for PBDEs, OCPs, PCBs, and PAHs, respectively. Their levels in the sediments in the three cities were generally consistent with the city industrialization. PBDEs and OCPs were markedly dominated by deca-BDE (>90 %) and DDTs (>70 %). A principle component analysis of the analytes identified three major factors suggesting different sources of the contaminants in the sediments. PBDEs and the organic carbon in the sediments have common sources from industrial activities; whereas OCPs and PCBs, correlated with the second factor, were mainly from historical sources. The third factor with loadings of PAHs is indicative of various combustion sources. Ecological risk assessment indicated that the potential highest risk is from DDTs, for which 22 sites exceed the effects range low (ERL) values and three sites exceed the effects range median (ERM) value.     

Evaluation of the effects of ozone and acidic precipitation,alone and in combination,on the photosynthesis,nutrition, and growth of red spruce and sugar maple

Substantial and widespread morbidity and mortality of red spruce have been observed in high elevation forests of the northeast under circumstances indicative of a stress-related disease. Whether red spruce at lower elevations are experiencing a more subtle loss of growth and vigor is uncertain. In addition, sugar maple has exhibited decline of varying extent and intensity for several decades. Forests in the northeast are exposed to two air pollutants, ozone (O₃) and acidic precipitation, that are widespread in occurrence and have the potential, both individually and collectively, to produce impacts to forest trees. the roles, if any, of these two stress agents in the tree declines found in the northeast are not known.In 1986, a five-year study was initiated to evaluate the effects of O₃ and acidic precipitation on red spruce and sugar maple. The trees will be exposed to controlled levels of O₃ and acidic precipitation in the field using open-top chambers. The experiment is a 4×3 factorial conducted in split plots with O₃ treatments as whole plots and simulated rain treatments comprising the split plots. Broadly stated, the research will evaluate the effects of the pollutants on the processes, fluxes, and pools associated with carbon, water, and nutrients in the soil/tree/atmosphere system. These evaluations will be conducted on a systems level and will be integrated through the development of mechanistic simulation models.Assessment of the effects of the treatments on carbon fixation by photosynthesis, the loss of carbon through respiration, and the allocation of carbon in growth will be a central focus of the study. Whole-tree cuvettes will be used to assess net photosynthesis, respiration, transpiration, and stomatal conductance.Considerable emphasis will be placed on determining the influences of the treatments on the biogeochemistry of the system. These studies will focus on the leaching of nutrients from the tree canopy, the mobilization and loss of nutrients from the soil, soil solution chemistry, and the alteration of tree nutrition by the input of additional nitrogen in precipitation.Statistical and simulation modeling will be used to assess and describe the effects of the treatments. The modeling approaches are different in technique, but complementary. Statistical models will be used to describe the responses of growth and physiological variables to the ozone and acidic precipitation treatments. Simulation models will be built to describe the relationships between photosynthesis, respiration, nutrition, and water use, how these processes are affected by the treatments, and how these effects ultimately result in altered growth. The simulation models will initially provide a framework for the formulation of hypotheses regarding the interrelationships of plant components and processes and how they are affected by the treatments.Contribution from Fourth World Wilderness Congress—Acid Rain Symposium, Denver (Estes Park), Colorado, September 11–18, 1987.     

Conventional, microwave, and ultrasound sequential extractions for the fractionation of metals in sediments within the Petrochemical Industry, Serbia

In this paper, the main objective was fractionation of Cd, Cu, Ni, Pb, Zn, Ca, Fe, and K in certificate material and sediment samples gathered from and around the Petrochemical Industry using the conventional, microwave and ultrasonic sequential extraction. Microwave oven and ultrasound bath were used as an energy source for achieving faster extraction. Additional heating and boiling of samples were avoided by using lower power and shorter time for microwave and ultrasound extraction. Precision and accuracy of procedure were evaluated by using certificate material (BCR701). Acceptable accuracy of metals (87.0–111.3 %) was achieved for all three-step sequential of conventional extraction protocol. An accuracy of the fourth step has been verified with two certificate materials: BCR143R and 146R. The range of total extracted metal concentrations from sediments was similar for all three extraction techniques. A significant high percentage of Cd, Cu, and Zn were obtained after extraction of the exchangeable and acid soluble sediment fraction. Principal component analysis of values obtained after determination of risk assessment code using conventional and ultrasound sequential extraction show similarity of these values. Accuracy, recovery, and risk assessment code values imply that ultrasound sequential extraction is a more suitable, accelerated sequential extraction procedure (30 min per extraction step) than microwave extraction in applied conditions.     

Heavy Metal Contents of the Karasu Creek Sediments, Nigde, Turkey

Heavy metal contamination in sediments of the Karasu spring was investigated in the presented study. In this respect, sediment samples were collected from contaminant sites along the spring starting from the spring water manifestation site, base of the Akkaya dam to the dam exit site. Heavy metal concentrations were determined by X-ray Fluorescence Spectrometer. Cobalt, copper, arsenic, tin, nickel, zinc, cadmium, lead, aluminum, iron, titan, chromium and manganese contents of the Karasu creek sediments are found as 18.30–69.00, 12.40–595.0 5.50–345.3, 5.80–15.1, 10.9–64.1, 28.90–103,300, 4.1–356.2, 7.70–37,840, 13,460–109,400, 11,740–62,900, 22.18–59.04, 41.70–369 and 12.09–3,480 mg/kg, respectively. Results indicate the presence of a contamination in the Karasu creek. All the metal concentrations were found to be exceeding their acceptable limit values. Eutrophication is developed in the Karasu creek and the Akkaya dam. It is thought that heavy metal accumulation in the creek is originated from discharge from mine quarries, industrial and domestic wastes. Protection zones should be defined and all necessary measures must be taken along the Karasu creek.