Kinetic and equilibrium isotherm studies for the adsorptive removal of Brilliant Green dye from aqueous solution by rice husk ash

The present study deals with the adsorption of Brilliant Green (BG) on rice husk ash (RHA). RHA is a solid waste obtained from the particulate collection equipment attached to the flue gas lines of rice husk fired boilers. Batch studies were performed to evaluate the influences of various experimental parameters like initial pH (pH0), contact time, adsorbent dose and initial concentration (C0) on the removal of BG. Optimum conditions for BG removal were found to be pH0 approximately 3.0, adsorbent dose approximately 6 g L(-1) of solution and equilibrium time approximately 5 h for the C0 range of 50-300 mg L(-1). Adsorption of BG followed pseudo-second-order kinetics. Intra-particle diffusion does not seem to control the BG removal process. Equilibrium isotherms for the adsorption of BG on RHA were analyzed by Freundlich, Langmuir, Redlich-Peterson (R-P), Dubnin-Radushkevich (D-R), and Temkin isotherm models using a non-linear regression technique. Langmuir and R-P isotherms were found to best represent the data for BG adsorption onto RHA. Adsorption of BG on RHA is favourably influenced by an increase in the temperature of the operation. Values of the change in entropy (DeltaS0) and heat of adsorption (DeltaH0) for BG adsorption on RHA were positive. The high negative value of change in Gibbs free energy (DeltaG0) indicates the feasible and spontaneous adsorption of BG on RHA.     

Application of surface molecular imprinting adsorbent in expanded bed for the adsorption of Ni(2+) and adsorption model

A new surface molecular imprinting adsorbent (SMIA) was used in an expanded bed. The expansion ratio and adsorption performance were studied at different volumetric rates, inlet concentrations, and pH values. A model based on the Adams-Bohart adsorption model of breakthrough curves was established. The predicted curves had good agreement with the experimental curves. The breakthrough time (T(1/2)) decreased with increasing inlet concentration when the outlet concentration was half the initial concentration (C/C(0)=0.5). The inlet concentration had little effect on the adsorption rate constant (k(1)) value when the initial concentration (C(0)) was above 150 mg/L. However, T(1/2) values increased with increasing initial pH of the inlet solution, and the k(1) value decreased due to the competition between H(+) and Ni(2+).     

Removal of copper (II) from aqueous solution by adsorption onto low-cost adsorbents

The use of low-cost adsorbents was investigated as a replacement for current costly methods of removing metals from aqueous solution. Removal of copper (II) from aqueous solution by different adsorbents such as shells of lentil (LS), wheat (WS), and rice (RS) was investigated. The equilibrium adsorption level was determined as a function of the solution pH, temperature, contact time, initial adsorbate concentration and adsorbent doses. Adsorption isotherms of Cu (II) on adsorbents were determined and correlated with common isotherm equations such as Langmuir and Freundlich models. The maximum adsorption capacities for Cu (II) on LS, WS and RS adsorbents at 293, 313 and 333 K temperature were found to be 8.977, 9.510, and 9.588; 7.391, 16.077, and 17.422; 1.854, 2.314, and 2.954 mg g(-1), respectively. The thermodynamic parameters such as free energy (delta G0), enthalpy (delta H0) and entropy changes (delta S0) for the adsorption of Cu (II) were computed to predict the nature of adsorption process. The kinetics and the factors controlling the adsorption process were also studied. Locally available adsorbents were found to be low-cost and promising for the removal of Cu (II) from aqueous solution.     

Adsorption of Pb and Cd on the natural surface coatings (NSCs) in the presence of organochlorine pesticides: a preliminary investigation

Adsorption of Pb and Cd in the presence and absence of organochlorine pesticides (OCPs) on natural surface coatings (NSCs), which were collected in the Nanhu Lake in Changchun, China, was measured in order to investigate the effect of the OCPs on the adsorption of heavy metals on the NSCs. Adsorption of Pb/Cd was carried out under controlled laboratory conditions (mineral salt solution with defined species, ionic strength 0.05 mol/l, 25 degrees C and pH 6.0) with initial Pb and Cd concentrations ranging from 0.2 to 2.5 mol/l. The classical Langmuir adsorption isotherm was applied to estimate the equilibrium coefficients of the adsorption of Pb and Cd on the NSCs. Adsorption interference between Pb/Cd and the OCPs on the NSCs indicated that the adsorption of Pb/Cd on the NSCs was influenced by the OCPs, and competitive adsorption between Pb and the OCPs was observed while adsorption of Cd was enhanced by addition of the OCPs. Adsorption data fit the Langmuir isotherm well for the NSCs treated with the OCPs at different equilibrium concentrations. The results showed that the amount of adsorbed Pb decreased by more than 40% while the amount of adsorbed Cd increased by over 60% with an increase in the initial concentrations of the OCPs ranging from 0 to 5.0 microg/l and that adsorption of Pb/Cd on the NSCs was strongly affected by the OCPs. This preliminary study highlights the importance of the OCPs on the NSCs in controlling the transport, fate, biogeochemistry, bioavailability and toxicity of trace metals in aquatic environments.     

Kinetic and equilibrium characterization of uranium(VI) adsorption onto carboxylate-functionalized poly(hydroxyethylmethacrylate)-grafted lignocellulosics

This study investigated the feasibility of using a new adsorbent prepared from coconut coir pith, CP (a coir industry-based lignocellulosic residue), for the removal of uranium [U(VI)] from aqueous solutions. The adsorbent (PGCP-COOH) having a carboxylate functional group at the chain end was synthesized by grafting poly(hydroxyethylmethacrylate) onto CP using potassium peroxydisulphate-sodium thiosulphite as a redox initiator and in the presence of N,N'-methylenebisacrylamide as a crosslinking agent. IR spectroscopy results confirm the graft copolymer formation and carboxylate functionalization. XRD studies confirm the decrease of crystallinity in PGCP-COOH compared to CP, and it favors the protrusion of the functional group into the aqueous medium. The thermal stability of the samples was studied using thermogravimetry (TG). Surface charge density of the samples as a function of pH was determined using potentiometric titration. The ability of PGCP-COOH to remove U(VI) from aqueous solutions was assessed using a batch adsorption technique. The maximum adsorption capacity was observed at the pH range 4.0-6.0. Maximum removal of 99.2% was observed for an initial concentration of 25mg/L at pH 6.0 and an adsorbent dose of 2g/L. Equilibrium was achieved in approximately 3h. The experimental kinetic data were analyzed using a first-order kinetic model. The temperature dependence indicates an endothermic process. U(VI) adsorption was found to decrease with an increase in ionic strength due to the formation of outer-sphere surface complexes on PGCP-COOH. Equilibrium data were best modeled by the Langmuir isotherm. The thermodynamic parameters such as DeltaG(0), DeltaH(0) and DeltaS(0) were derived to predict the nature of adsorption. Adsorption experiments were also conducted using a commercial cation exchanger, Ceralite IRC-50, with carboxylate functionality for comparison. Utility of the adsorbent was tested by removing U(VI) from simulated nuclear industry wastewater. Adsorbed U(VI) ions were desorbed effectively (about 96.2+/-3.3%) by 0.1M HCl. The adsorbent was suitable for repeated use (more than four cycles) without any noticeable loss of capacity.     

Removal of basic dye (Astrazon Blue FGRL) using macroalga Caulerpa lentillifera

The macroalga Caulerpa lentillifera was found to have adsorption capacity for a basic dye, Astrazon Blue FGRL. For the whole range of concentrations employed in this work (20-1280 mgl(-1)), the adsorption reached equilibrium within the first hour. The kinetic data corresponded well with the pseudo second-order kinetic model where the rate constants decreased as initial dye concentrations increased. At low dye concentrations (20-80 mgl(-1)), an increase in the adsorbent dosage resulted in a higher removal percentage of the dye, but a lower amount of dye adsorbed per unit mass (q). The adsorption isotherm followed both the Langmuir and Freundlich models within the temperature range employed in this work (18-70 degrees C). The highest maximum adsorption capacity (q(m)) was obtained at 50 degrees C. The enthalpy of adsorption was estimated at 14.87 kJmol(-1) suggesting a chemical adsorption mechanism.     

Adsorption of methylene blue from aqueous solution by jackfruit (Artocarpus heteropyllus) leaf powder: A fixed-bed column study

Continuous fixed-bed studies were undertaken to evaluate the efficiency of jackfruit leaf powder (JLP) as an adsorbent for the removal of methylene blue (MB) from aqueous solution under the effect of various process parameters like bed depth (5–10 cm), flow rate (30–50 mL/min) and initial MB concentrations (100–300 mg/L). The pH at point of zero charge (pH_PZC) of the adsorbent was determined by the titration method and a value of 3.9 was obtained. A FTIR of the adsorbent was done before and after the adsorption to find the potential adsorption sites for interaction with methylene blue molecules. The results showed that the total adsorbed quantities and equilibrium uptake decreased with increasing flow rate and increased with increasing initial MB concentration. The longest breakthrough time and maximum MB adsorption were obtained at pH 10. The results showed that the column performed well at low flow rate. Also, breakthrough time and exhaustion time increased with increasing bed depth. The bed-depth service time (BDST) model and the Thomas model were applied to the adsorption of MB at different bed depths, flow rates, influent concentrations and pH to predict the breakthrough curves and to determine the characteristic parameters of the column that are useful for process design. The two model predictions were in very good agreement with the experimental results at all the process parameters studied indicating that they were very suitable for JLP column design.     

Adsorptive removal of Cd(II) and Pb(II) ions from aqueous solutions by using Turkish illitic clay

The ability of Turkish illitic clay (TIC) in removal of Cd(II) and Pb(II) ions from aqueous solutions has been examined in a batch adsorption process with respect to several experimental conditions including initial solution pH, contact time, initial metal ions concentration, temperature, ionic strength, and TIC concentration, etc. The characterization of TIC was performed by using FTIR, XRD and XRF techniques. The maximum uptake of Cd(II) (11.25 mg g⁻¹) and Pb(II) (238.98 mg g⁻¹) was observed when used 1.0 g L⁻¹ of TIC suspension, 50 mg L⁻¹ of initial Cd(II) and 250 mg L⁻¹ of initial Pb(II) concentration at initial pH 4.0 and contact time of 240 min at room temperature. The experimental data were analyzed by the Langmuir, Freundlich, Temkin and Dubinin Radushkevich (D-R) isotherm models. The monolayer adsorption capacity of TIC was found to be 13.09 mg g⁻¹ and 53.76 mg g⁻¹ for Cd(II) and Pb(II) ions, respectively. The kinetics of the adsorption was tested using pseudo-first-order, pseudo-second-order, Elovich and intraparticle diffusion models. The results showed that the adsorption of Cd(II) and Pb(II) ions onto TIC proceeds according to the pseudo-second-order model. Thermodynamic parameters including the Gibbs free energy (ΔG), enthalpy (ΔH), and entropy (ΔS) changes indicated that the present adsorption process was feasible, spontaneous and endothermic in the temperature range of 5–40 °C.     

Adsorption characteristics of Cu and Ni on Irish peat moss

Peat has been widely used as a low cost adsorbent to remove a variety of materials including organic compounds and heavy metals from water. Various functional groups in lignin allow such compounds to bind on active sites of peat. The adsorption of Cu(2+) and Ni(2+) from aqueous solutions on Irish peat moss was studied both as a pure ion and from their binary mixtures under both equilibrium and dynamic conditions in the concentration range of 5-100mg/L. The pH of the solutions containing either Cu(2+) or Ni(2+) was varied over a range of 2-8. The adsorption of Cu(2+) and Ni(+2) on peat was found to be pH dependent. The adsorption data could be fitted to a two-site Langmuir adsorption isotherm and the maximum adsorption capacity of peat was determined to be 17.6 mg/g for Cu(2+) and 14.5mg/g for Ni(2+) at 298 K when the initial concentration for both Cu(2+) and Ni(2+) was 100mg/L, and the pH of the solution was 4.0 and 4.5, respectively. Column studies were conducted to generate breakthrough data for both pure component and binary mixtures of copper and nickel. Desorption experiments showed that 2mM EDTA solution could be used to remove all of the adsorbed copper and nickel from the bed.     

Removal of Pb(II) ions from aqueous solution using activated tea waste: Adsorption on a fixed-bed column

An inexpensive and effective adsorbent was developed from waste tea leaves for the dynamic uptake of Pb(II). Characterization of the adsorbents showed a clear change between physico-chemical properties of activated tea waste and simply tea waste. The purpose of this work was to evaluate the potential of activated tea waste in continuous flow removal of Pb(II) ions from synthetic aqueous effluents. The performance of the system was evaluated to assess the effect of various process variables, viz., of bed height, hydraulic loading rate and initial feed concentration on breakthrough time and adsorption capacity. The shape of the breakthrough curves was determined for the adsorption of Pb(II) by varying different operating parameters like hydraulic loading rate (2.3–9.17 m³/h m²), bed height (0.3–0.5 m) and feed concentration (2–10 mg/l). An attempt has also been made to model the data generated from column studies using the empirical relationship based on the Bohart–Adams model. There was an acceptable degree of agreement between the data for breakthrough time calculated from the Bohart–Adams model and the present experimental study with average absolute deviation of less than 5.0%. The activated tea waste in this study showed very good promise as compared with the other adsorbents available in the literature. The adsorbent could be suitable for repeated use (for more than four cycles) without noticeable loss of capacity.     

Adsorption and degradation of triazophos, chlorpyrifos and their main hydrolytic metabolites in paddy soil from Chaohu Lake, China

Triazophos and chlorpyrifos are organophosphorus pesticides (OPs), and their primary hydrolytic metabolites are 1-phenyl-3-hydroxy-1,2,4-triazole (BZC) and 3,5,6-trichloro-2-pyridinol (TCP). In this study, the adsorption and degradation of triazophos, chlorpyrifos, BZC and TCP were investigated in paddy soil from Chaohu Lake, China. Adsorption tests demonstrated that the adsorption of these compounds to soils could be described by the Freundlich equation. Moreover, chlorpyrifos displayed the highest affinity for adsorption, followed by triazophos, BZC and TCP. Degradation of these compounds in non-sterile soil followed first-order exponential decay kinetics, and the half-life (t(1/2)) of these contaminants ranged from 8.40 to 44.34 d. Sterilization of soil decreased the degradation rate, indicating that microorganisms played a significant role in the degradation of these compounds. The values of t(1/2) and K(oc) were fitted to obtain models that could predict the leaching potential of the contaminants from soil. Compared to their parent compounds, BZC and TCP showed high potential for leaching into groundwater. The inoculation of OPs-degrading bacterium (Diaphorobacter sp. GS-1) removed 95.38%, 100% and 100% of triazophos, chlorpyrifos and BZC in paddy soil after 21 d, respectively. The pollution risk of triazophos, chlorpyrifos and BZC could be greatly decreased by inoculating soil with Diaphorobacter sp. GS-1, which decreases the t(1/2) of the contaminants.     

Lead removal from contaminated water using mineral adsorbents

This study records experiments undertaken to determine the suitable conditions for the use of naturally occurring minerals (talc, chalcopyrite and barite) as an adsorbent for the removal of lead ions from liquid wastes. The adsorption of lead ions from solutions containing different initial lead concentrations (50, 100, 200, 400, 600, 800 and 1000 mg l^–1 Pb as lead nitrate) using different size fractions (<63 m, 63–150 m) of talc, chalcopyrite and barite at different pH (3, 5, 7 and 9) and different adsorption times (24, 48, 72 and 96 hr) was examined. The results revealed that of the studied minerals, the chalcopyrite fraction at 63–150 m showed the highest adsorption capacity. The adsorption data of Pb ions was also analyzed with the help of the Langmuir and Freundlich models to evaluate the mechanistic parameters associated with the adsorption process. The adsorption isotherms obtained from the Langmuir and Freundlich equations were generally linear and the adsorption of Pb by the studied minerals was correlated with the adsorption maximum and binding energy constant of the Langmuir equation and equilibrium partition constant and binding partition coefficient of the Freundlich equation. It was concluded that the equilibrium time of adsorption was 72 hr at an optimum pH from 7 to 9. This technique might be successfully used for the removal of lead ions from liquid industrial wastes and wastewater.     

Removal of the hazardous dye rhodamine B through photocatalytic and adsorption treatments

This paper reports on photocatalytic and adsorptive treatment of a hazardous xanthene dye, Rohdamine B, in wastewater. The photocatalytic degradation was carried out in the presence of the catalyst TiO(2) and the effects of pH, concentration of the dye, amount of TiO(2), temperature and electron acceptor H(2)O(2) on the degradation process were observed. It was found that photocatalytic degradation by TiO(2) is an effective, economical and faster mode of removing Rohdamine B from aqueous solutions. Attempts were also made to utilize activated carbon and rice husk as potential adsorbents to remove Rhodamine B from wastewater. The adsorption studies were carried out at 40, 50 and 60 degrees C, and the effects of pH, temperature, amount of adsorbents, concentration of adsorbate, etc., on the adsorption were measured. On the basis of adsorption data the Langmuir and Freundlich adsorption isotherm models were also confirmed. The adsorption isotherm constants thus obtained were employed to calculate thermodynamic parameters like Gibb's free energy, change in enthalpy and entropy. In order to observe the quality of wastewater COD measurements were also carried out before and after the treatments. A significant decrease in the COD values was observed, which clearly indicates that both photocatalytic and adsorption methods offer good potential to remove Rhodamine B from industrial effluents.     

Utilization of waste product (tamarind seeds) for the removal of Cr(VI) from aqueous solutions: Equilibrium, kinetics, and regeneration studies

In the present study, an adsorbent was prepared from tamarind seeds and used after activation for the removal of Cr(VI) from aqueous solutions. The tamarind seeds were activated by treating them with concentrated sulfuric acid (98% w/w) at a temperature of 150 °C. The adsorption of Cr(VI) was found to be maximum at low values of initial pH in the range of 1–3. The adsorption process of Cr(VI) was tested with Langmuir, Freundlich, Redlich–Peterson, Koble–Corrigan, Tempkin, Dubinin–Radushkevich and Generalized isotherm models. Application of the Langmuir isotherm to the system yielded a maximum adsorption capacity of 29.7 mg/g at an equilibrium pH value ranging from 1.12 to 1.46. The adsorption process followed second-order kinetics and the corresponding rate constants obtained were 2.605 × 10⁻³, 0.818 × 10⁻³, 0.557 × 10⁻³ and 0.811 × 10⁻³ g/mg min⁻¹ for 50, 200, 300 and 400 mg/L of initial Cr(VI) concentration, respectively. The regenerated activated tamarind seeds showed more than 95% Cr(VI) removal of that obtained using the fresh activated tamarind seeds. A feasible solution is proposed for the disposal of the contaminants (acid and base solutions) containing high concentrations of Cr(VI) obtained during the regeneration (desorption) process.     

Determination of model parameters for zinc (II) ion biosorption onto powdered waste sludge (PWS) in a fed-batch system

Biosorption of zinc (II) ions onto pre-treated powdered waste sludge (PWS) was investigated using a completely mixed tank operating in fed-batch mode instead of an adsorption column. Experiments with variable feed flow rate (0.05-0.5 L h(-1)), feed Zn(II) ion concentrations (37.5-275 mg L(-1)) and amount of adsorbent (1-6 g PWS) were performed using fed-batch operation at pH 5 and room temperature (20-25 degrees C). Break-through curves describing variations of aqueous (effluent) zinc ion concentrations with time were determined for different operating conditions. Percent zinc removal from the aqueous phase decreased, but the biosorbed (solid phase) zinc ion concentration increased with increasing feed flow rate and zinc concentration. A modified Bohart-Adams equation was used to determine the biosorption capacity of PWS (q'(s)) and the rate constant (K) for zinc ion biosorption. Biosorption capacity (q'(s)=57.7 g Zn kg(-1) PWS) of PWS in fed-batch operation was found to be comparable with powdered activated carbon (PAC) in column operations. However, the adsorption rate constant (K=9.17 m(3) kg(-1) h(-1)) in fed-batch operation was an order of magnitude larger than those obtained in adsorption columns because of elimination of mass transfer limitations encountered in the column operations. Therefore, a completely mixed tank operated in fed-batch mode was proven to be more advantageous as compared to adsorption columns due to better contact between the phases yielding faster adsorption rates.     

Effect of liquid cow manure on andisol properties and atrazine adsorption

Application of animal manure amendments to agricultural soils is a common practice to improve soil fertility through the addition of essential plant nutrients. This practice may increase the potential for atrazine (2-chloro-4-ethylamino-6-isopropylamino-1, 3, 5-triazine) leaching due to competition for adsorption sites between the pesticide and dissolved organic carbon (DOC) added through manure. We evaluated the influence of liquid cow manure (LCM) application on soil properties, atrazine adsorption, and the physicochemical controlling mechanisms in an Andisol. The LCM was applied at rates equivalent to 0, 100,000, 200,000, and 300,000 L ha(-1), resulting in treatments S-0, S-100, S-200, and S-300, respectively. The LCM application increased DOC and pH of the soils immediately on addition, but pH returned to S-0 values 30 d after application. The LCM application did not modify atrazine adsorption with the two lowest application rates (S-100 and S-200), but atrazine adsorption was decreased in S-300 (K(f) = 0.96) compared with the control (S-0) (K(f) = 1.19), possibly due to the competitive adsorption of DOC with the pesticide. The Fourier-transformed infrared analysis showed that LCM increased aliphaticity and presence of N-containing groups and polysaccharide-like groups in amended soils; however, these properties did not modify the atrazine interaction in the studied amended soils. Interestingly the addition of DOC to soil at the high application rate (S-300) reduced atrazine adsorption in this rich OM Andisol despite the LCM not raising the concentration of stable organic matter. The application of high rates of liquid manure containing DOC incurs an increased risk of pesticide leaching.     

Application of 'waste' wood-shaving bottom ash for adsorption of azo reactive dye

The utilization of wood-shaving bottom ash (WBA) for the removal of Red Reactive 141 (RR141), an azo reactive dye, was investigated. WBA/H(2)O and WBA/H(2)SO(4) were made by treating WBA with water and 0.1M H(2)SO(4), respectively, to increase adsorption capacity. Adsorption of RR141 from reactive dye solution (RDS) and reactive dye wastewater (RDW) by WBA/H(2)O and WBA/H(2)SO(4) involved the BET surface area and pore size diameter. Properties of adsorbents, effect of contact time, initial pH of solution, dissolved metals and elution studies indicated that the decolorisation mechanism involved both chemical adsorption and precipitation with calcium ions. In addition, the WBA/H(2)SO(4) surface might contain sulphate-cation complexes that were specific to enhancing dye adsorption from RDW. The adsorption isotherm had a best fit by the Freundlich model. Freundlich parameters showed that WBA/H(2)O used more heterogeneous surface than WBA/H(2)SO(4) and activated carbon for RDW adsorption. A thermodynamic study indicated that RDW adsorption was an endothermic process. The maximum dye adsorption capacities of WBA/H(2)O, WBA/H(2)SO(4) and activated carbon obtained from a Langmuir model at 30 degrees C were 24.3, 29.9, and 41.5mgl(-1), respectively. In addition, WBA/H(2)O and WBA/H(2)SO(4) could reduce colour and high chemical oxygen demand (COD) of real textile wastewater. According to the difficulty in the elution study, it was an environmentally safe disposal of this waste. Therefore, WBA, a waste from combustion of wood shavings, was suitable to be used as an effective adsorbent for azo reactive dye removal.     

Adsorption of eosin dye on activated carbon and its surfactant based desorption

The performance of activated carbon has been investigated for the adsorption of eosin dye dissolved in water. Eosin is anionic in nature and highly toxic. The effects of initial dye concentration, contact time, pH and temperature on adsorption of eosin by a fixed amount of activated carbon (1.0 g/L) have been studied in batch and column mode. The equilibrium data are successfully fitted to the Freundlich adsorption isotherm. The adsorption rate data are successfully explained by a pseudo second-order kinetic model. Breakthrough curves for column adsorption have also been studied. The regeneration of spent carbon by desorbing the dye has been experimentally investigated applying a surfactant enhanced carbon regeneration (SECR) technique using both cationic and anionic surfactants. An empirical kinetic model for dye desorption from the commercial activated carbon (CAC) using different surfactant and desorption techniques, viz. change in pH, has been proposed. The comparison between the model and the experimental results is found to be satisfactory.     

Highly siliceous MCM-48 from rice husk ash for CO2 adsorption

Mesoporous MCM-48 silica was synthesized using a cationic-neutral surfactant mixture as the structure-directing template and rice husk ash (RHA) as the silica source. The MCM-48 samples were characterized by X-ray powder diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), N₂ physisorption and SEM. X-ray diffraction pattern of the resulting MCM-48 revealed typical pattern of cubic Ia3d mesophase. BET results showed the MCM-48 to have a surface area of 1024 m²/g and FT-IR revealed a silanol functional group at about 3460 cm⁻¹. Breakthrough experiments in the presence of MCM-48 were also carried out to test the material's CO₂ adsorption capacity. The breakthrough time for CO₂ was found to decrease as the temperature increased from 298 K to 348 K. The steep slopes observed shows the CO₂ adsorption occurred very quickly, with only a minimal mass transfer effect and very fast kinetics. In addition, amine grafted MCM-48, APTS-MCM-48 (RHA), was prepared with the 3-aminopropyltriethoxysilane (APTS) to investigate the effect of amine functional group in CO₂ separation. An order of magnitude higher CO₂ adsorption capacity was obtained in the presence of APTS-MCM-48 (RHA) compared to that with MCM-48 (RHA). These results suggest that MCM-48 synthesized from rice husk ash could be usefully applied for CO₂ removal.     

Application of cupuassu shell as biosorbent for the removal of textile dyes from aqueous solution

The cupuassu shell (Theobroma grandiflorum) which is a food residue was used in its natural form as biosorbent for the removal of C.I. Reactive Red 194 and C.I. Direct Blue 53 dyes from aqueous solutions. This biosorbent was characterized by infrared spectroscopy, scanning electron microscopy, and nitrogen adsorption/desorption curves. The effects of pH, biosorbent dosage and shaking time on biosorption capacities were studied. In acidic pH region (pH 2.0) the biosorption of the dyes were favorable. The contact time required to obtain the equilibrium was 8 and 18 h at 298 K, for Reactive Red 194 and Direct Blue 53, respectively. The Avrami fractionary-order kinetic model provided the best fit to experimental data compared with pseudo-first-order, pseudo-second-order and chemisorption kinetic adsorption models. The equilibrium data were fitted to Langmuir, Freundlich, Sips and Radke-Prausnitz isotherm models. For both dyes the equilibrium data were best fitted to the Sips isotherm model.