Alkaline Degradation of Cellulose: Mechanisms and Kinetics

Cellulose powder and softwood sawdust were subjected to alkaline degradation under conditions representative of a cementitious environment for periods of 7 and 3 years, respectively. During the first 3 years, sampling was frequent, and data on the degradation of cellulose and production of isosaccharinic acid was used for establishing long-term prediction models. Samples after an additional period of 4 years were compared to the predicted values. The total rate of degradation was measured as the increase in total organic carbon (TOC) in corresponding solutions. A previously published theoretical model of degradation kinetics gave a good approximation of the present experimental data. Peeling-off, stopping, and alkaline hydrolysis reaction rate constants were obtained as model parameters, and the results suggested that the transformation of the glucose end group is the rate-limiting step in the cellulose peeling-off reaction and also determines the pH dependence of that reaction. After 3 years, isosaccharinic (ISA) acid represented 70–85% of all degradation products as quantified by capillary zone electrophoresis. The long-term prediction model indicated that all of the cellulose would be degraded after only 150–550 years. The control sampling after 7 years points toward a lower degradation of cellulose and production of ISA than predicted by the model, reflecting either a degradation of ISA that was faster than the production or a termination of the ISA production.     

Rheology of Lyocell Solutions from Different Cellulose Sources

Rheological measurements were used to characterize the behavior of lyocell solutions, i.e., cellulose dissolved in N-methymorpholine-N-oxide. Cellulose sources included dissolving pulp, kraft pulp, sugar cane fibers, and kenaf fibers. The dominance of viscous behavior, G values, over elastic behavior, G values, is affected by cellulose concentration and molecular weight. At lower concentrations and degrees of polymerization (DP), dissolving pulp solutions show viscous, inelastic behavior at low frequencies. At higher concentration and DP, dissolving pulp solutions are more elastic at higher frequencies. Solutions prepared with kenaf and sugar cane fibers show similar properties to those using pure dissolving pulp, and comparisons suggest the molecular weight and/or the presence of other substances such as lignin in the cellulose from these alternative sources affect the rheology.     

Preparation of Cellulose Nanocrystals Using an Ionic Liquid

In this paper cellulose nanocrystals were prepared by treating microcrystalline cellulose with 1-butyl-3-methylimidazolium hydrogen sulphate ionic liquid. Cellulose nanocrystals, after separation from ionic liquid, were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR), Field emission scanning electron microscopy (FESEM) Transmission Electron Microscope (TEM) and Thermogravimetric analysis. XRD results showed no changes in type of cellulose after the treatment with ionic liquid, however, high crystallinity index was observed in the ionic liquid treated sample. Cellulose nanocrystals, having length around 50–300 nm and diameter around 14–22 nm were observed in the ionic liquid treated sample under FESEM and TEM, and similar patterns of peaks as that of microcrystalline cellulose were observed for cellulose nanocrystals in the FTIR spectra. The thermal stability of the cellulose nanocrystals was measured low as compare to microcrystalline cellulose.     

Properties of Regenerated Cellulose Short Fibers/Cellulose Green Composite Films

Green composites of regenerated cellulose short fibers/cellulose were prepared by dissolving cellulose in a green solvent of 7% NaOH/12% Urea aqueous solution that was pre cooled at ?12?°C. The effect of fiber loading on the tensile, optical, thermal degradation and cell viability was studied. The tensile properties of cellulose were improved by the regenerated cellulose fiber reinforcement. The interfacial bonding between the fibers and matrix was assessed using the fractographs and found it to be good.     

Effect of Sequential Mixing and Compounding Conditions on Cellulose Acetate/Layered Silicate Nanocomposites

Injection molded nanocomposites have been successfully fabricated from cellulose acetate (CA), eco-friendly triethyl citrate (TEC) plasticizer, and organically modified clay with and without maleic anhydride grafted cellulose acetate butyrate (CAB-g-MA) as a compatibilizer. The effects of processing conditions such as mixing methods, pre-plasticizing times, extruder retention times (RT) and addition of compatibilizer on the performance of these nanocomposites have been evaluated. The cellulosic plastic with CA/TEC (80/20 wt%) was used as the polymer matrix for nanocomposite fabrication. The morphologies of these nanocomposites were evaluated through X-ray diffraction (XRD) and transmission electron microscopy (TEM) studies. The mechanical properties of the nanocomposites were measured and have been correlated with the XRD and TEM observations. From all of the sequential mixing methods used, powder–powder mixing leads to the most transparent nanocomposites. Cellulosic plastic-based nanocomposites obtained using increased pre-plasticizing times and RT showed better exfoliated structures. In the system containing compatibilizer, the minimum retention time required for obtaining almost completely exfoliated hybrid nanocomposites was shorter than in the system without compatibilizer.     

All-Cellulose Composite Fibers Obtained by Electrospinning Dispersions of Cellulose Acetate and Cellulose Nanocrystals

All-cellulose composite fibers were produced by electrospinning dispersions containing cellulose acetate (CA) and cellulose nanocrystals (CNCs). Precursor polymer matrices were obtained after dispersion of CA with different degrees of substitution in a binary mixture of organic solvents. The obtained fibers of CA loaded with CNCs had typical widths in the nano- and micro-scale and presented a glass transition temperature of 145?°C. The CA component was converted to cellulose by using alkaline hydrolysis to yield all-cellulose composite fibers that preserved the original morphology of the precursor system. Together with Fourier Transform Infrared Spectroscopy fingerprints the thermal behavior of the all-cellulose composite fibers indicated complete conversion of cellulose acetate to regenerated cellulose. Noticeable changes in the thermal, surface and chemical properties were observed upon deacetylation. Not only the thermal transitions of cellulose acetate disappeared but the initial water contact angle of the web was reduced drastically. Overall, we propose a simple method to produce all-cellulose composite fibers which are expected to display improved thermo-mechanical properties while keeping the unique features of the cellulose polymer.     

Polyhydroxybutyrate-Based Nanocomposites with Cellulose Nanocrystals and Bacterial Cellulose

Polyhydroxybutyrate (PHB) films nanoreinforced with hydrolyzed cellulose nanocrystals (CNC) and bacterial cellulose (BC) were prepared by solvent casting. The influence of different cellulose nanoparticles content (2, 4 and 6 wt% of CNC and 2 wt% of BC) on the PHB properties was studied. CNC nanocomposites presented good dispersion of the nanocrystals, improving transparency, mechanical and barrier properties of the PHB films. On the other hand, reduced thermal stability and mechanical properties were yielded by BC addition due to the intrinsic lower degradation temperature and higher length of the BC nanofibrils compared to CNC. Nanocomposites performance variation is mainly caused by the marked difference in nanoparticles structure. It was demonstrated that PHB–CNC films exhibited higher performance enhancement without detrimental effect of the pristine PHB properties.     

Extraction of Cellulose Nanocrystals from Phormium tenax Fibres

Cellulose nanocrystals with an acicular structure ranged from 100 to 200 nm in length and 15 nm in width were extracted from Phormium tenax leaf fibres by acid hydrolysis. A two-step procedure for the extraction of nano-sized cellulose was studied and the obtained nanocrystals were characterized using morphological investigations (optical, scanning electron and atomic force microscopy), as well as physico-chemical characterization by Wide Angle X-ray Scattering, infrared spectroscopy and thermogravimetric analysis. A study of birefringence properties was also performed. The first chemical treatment leads to the production of holocellulose by the gradual removal of lignin, while the subsequent sulphuric acid hydrolysis process allows obtaining cellulose nanocrystals in an aqueous suspension. The results reported support the repeatability and the effectiveness of the procedure performed. Moreover, the high cellulose content of P. tenax fibre and their declining market interest, suggest the interest of this investigation and the possibility to use natural fibres for the production of a reinforcement phase to involve in the nanocomposite approach for industrial applications.     

球形纤维素吸附剂对Cr3+吸附和解吸的研究

用静态法和动态法研究了球形纤维素吸附剂对水中 Cr3+的吸附和解吸 ,包括静态等温吸附以及各种因素对吸附的影响等 ,并探讨了吸附机理。 Cr3+的吸附容量为 2 8mg/ g,采用浓度为 1.2 mol/ L 的 HCl溶液作解吸液回收 Cr3+的综合效果较好。静态法和动态法的吸附率均达 90 %左右 ,解吸率均达 85 %以上 ,且静态法的吸附率和解吸率分别略高于动态法的吸附率和解吸率 ,但动态法耗时短 ,更符合工业化要求。     

Evaluation of the Biodegradation of Starch and Cellulose Under Controlled Composting Conditions

In order to verify the response of the controlled composting test method (i.e., the ISO/DIS 14855:1997, the ASTM D 5338-92, or the CEN counterpart) to starch at different concentrations, the maximum amount prescribed by the test method (100 g) and lower amounts (60 and 30 g), as if starch were a coingredient in a blend, were tested. After 44 days of incubation (at a constant temperature of 58°C) the biodegradation curves were in a plateau phase, displaying the following final values (referred to a nominal starch initial amount of 100 g): starch 100 g, 97.5%; starch 60 g, 63.7%; and starch 30 g, 32.5%. The data show a CO₂ evolution roughly equal, in each case, to the theoretical maximum, indicating a complete starch mineralization. We cannot discern whether the deviations found at lower concentrations are caused by a priming effect. In any case, the extent of the deviations is not high and is acceptable in biodegradation studies. The average biodegradation of cellulose, obtained gathering four independent experiments with 11 biodegradation curves, turned out to be 96.8 ± 6.7% (SD) after 47 ± 1 days. The data indicate that the controlled composting is a reliable test method also for starch and cellulose and, consequently, for starch-based and cellulose-based materials.     

Cellulose and Nanocellulose from Maize Straw: An Insight on the Crystal Properties

In this work cellulose was extracted from corn/maize straw (Zea mays) by means of an environmental-friendly multistep procedure involving alkaline treatment and a totally chlorine-free bleaching. This multistep procedure efficiently removed lignin and hemicelluloses. The pulp resulting from each step was characterized by attenuated total reflectance fourier transform infrared spectroscopy (ATR-FTIR). The optimum pulping time (time of alkaline treatment) was determined by means of thermogravimetric analysis. The extracted cellulose is highly crystalline as verified by X-ray diffraction. The partial acid hydrolysis with sulfuric acid led to the isolation of cellulose whiskers in aqueous suspension as confirmed by light scattering and transmission electron microscopy. The depolarization ratio value of these nanocrystals is the same as that determined for cotton whiskers, showing that this ratio does not depend on the cellulose source. The maize whiskers are arranged laterally in bundles with average thickness around five times that of the crystallite.     

Lyotropic Liquid Crystal Phases in Cellulose Acetate Phthalate/Hydroxypropyl Cellulose Blends

Cellulose and some of its derivatives form liquid crystalline solutions in a variety of solvents. The present work investigates cellulose acetate phthalate/hydroxypropyl cellulose blends in N,N-dimethylacetamide, in function of concentration and composition, by rheology, considering dynamic viscometry and oscillatory shear tests. The effects of composition, concentration, shear rate, and oscillatory deformation on the rheological functions determines the orientation or mobility of the chain segments in the shear field. Atomic force microscopy and polarized light microscopy studies on corresponding films show that specific interactions, such as the hydrogen bonds between cellulose acetate phthalate and the liquid crystalline component—hydroxypropyl cellulose, stabilizes the morphology, leading to the emergence of different formations typical for lyotropic liquid crystal phases. These studies contribute to a better knowledge of the specific interactions that generate and modify the liquid crystalline properties of cellulose derivatives, required by the applications in electronic domains.     

Cellulose Fiber Isolation and Characterization from Sweet Blue Lupin Hull and Canola Straw

In this study, cellulose fibers were removed from crop by-products using a combination of sodium hydroxide treatment followed by acidified sodium chlorite treatment. The objective was to obtain high recovery of cellulose by optimizing treatment conditions with sodium hydroxide (5–20%, 25–75 °C and 2–10 h) followed by acidified sodium chlorite (1.7%, 75 °C for 2–6 h) to remove maximum lignin and hemicellulose, as well as to investigate the effect of lignin content of the starting materials on the treatment efficiency. Samples were characterized for their chemical composition, crystallinity, thermal behavior and morphology to evaluate the effects of treatments on the fibers’ structure. The optimum sodium hydroxide treatment conditions for maximum cellulose recovery was at 15% NaOH concentration, 99 °C and 6 h. Subsequent acidified sodium chlorite treatment at 75 °C was found to be effective in removing both hemicellulose and lignin, resulting in higher recovery of cellulose in lupin hull (~?95%) and canola straw (~?93%). The resultant cellulose fibers of both crop by-products had increased crystallinity without changing cellulose I structure (~?68–73%). Improved thermal stabilities were observed with increased onset of degradation temperatures up to 307–318 °C. Morphological investigations validated the effectiveness of treatments, revealing disrupted cell wall matrix and increased surface area due to the removal of non-cellulosics. The results suggest that the optimized combination of sodium hydroxide and acidified sodium chlorite treatments could be effectively used for the isolation of cellulose fibers from sweet blue lupin hull and canola straw, which find a great number of uses in a wide range of industrial applications.     

Bacterial Cellulose from Simple and Low Cost Production Media by Gluconacetobacter xylinus

Bacterial cellulose pellicles were produced by Gluconacetobacter xylinus using non conventional low-cost carbon sources, such as glycerol remaining from biodiesel production and grape bagasse, a residue of wine production. The carbon sources assayed showed their suitability for microbial cellulose production, with relatively high production values such as 10.0 g/l for the culture medium with glycerol from biodiesel as carbon source and corn steep liquor as nitrogen source; and 8.0 g/l for the culture medium containing grape bagasse and corn steep liquor. Glucose, commercial glycerol and cane molasses were also assayed as carbon sources for comparison. The bacterial celluloses produced were characterized by means of scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy and thermogravimetric analysis. Morphological analysis showed that bacterial cellulose microfibrils produced from the non-conventional media used were several micrometers long and had rectangular cross-sections with widths and thicknesses in the range of 35–70 and 13–24 nm, respectively. X-ray patterns showed crystallinity levels in the range of 74–79 % (area method), whereas both X-ray patterns and infrared spectroscopy evidenced the presence of peaks characteristic of Cellulose I polymorph. Besides thermal properties were similar to those found for the pellicle obtained from glucose. The study performed showed the suitability of using wine residues or glycerol remaining from increasing biodiesel production as cheap carbon sources for production of bacterial cellulose microfibrils, with similar characteristics as those obtained by use of more expensive carbon sources such as glucose or commercial glycerol. On the other hand, the low cost nitrogen sources used (corn steep liquor or diammonium phosphate) also contributed to the economy of the bioprocess.     

Preparation and Characterization of Cellulose/Polypropylene Composite Using an Oxidatively Degraded Polypropylene

In this work, an oxidatively degraded polypropylene (DgPP) was studied as a novel coupling agent for fibrous cellulose (FC)/polypropylene (PP) composite. An optimal preparation time of PP thermal oxidative degradation was 18 h at 130 °C, and the DgPP had functional groups such as γ-lactone and acid groups. The spherulite observation of the DgPP suggested miscibility for the undegraded PP. The addition of the DgPP presented the transparency improvement of FC/PP composite, and this behavior was found to be originated from the grafted DgPP, which was produced by the esterification reaction between the of FC and the DgPP. The scanning electron microscope (SEM) observation showed that the grafted DgPP coated the FC surface, and the tensile strength of the FC/PP composite increased by an appropriate amount of the DgPP addition. These results suggested that the DgPP was suitable for the coupling agent of FC/PP composite.     

Experimental Investigation of Cellulose/Silver Nanocomposites Using In Situ Generation Method

Cellulose gel films were prepared by regeneration process using pre-cooled aq.(8 wt% LiOH + 15 wt% urea) mixture as solvent and ethyl alcohol as non solvent. The Terminus cattapa leaf extract diffused wet cellulose films were then dipped in 1–5 mM aq.AgNO₃ solutions to allow in situ generation of silver nanoparticles (AgNPs). Besides the in situ generation, some AgNPs were also formed outside the wet films in the solution. The AgNPs formed outside the films were observed under transmission electron microscope and scanning electron microscope. The nanocomposite films were also characterized by Fourier transform infrared spectroscopy, X-ray diffraction and thermogravimetric analysis and tensile test. The thermal stability of the composite films was lower than that of the matrix up to a temperature of ~300 °C and afterwards showed a reverse trend. The tensile strength of the nanocomposite films was found to be higher than the matrix but decreased with increasing concentration of aq.AgNO₃. The cellulose/AgNPs composite films showed good antibacterial activity against E. coli (gram positive) and Bacillus sp. (gram negative). Based on the aforementioned properties, the cellulose/AgNPs composite films can be considered for antibacterial packaging and medical applications.     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

A Simple Assay for Monitoring Cellulose in Paper-Spiked Soil

We describe a simple method for measuring cellulose in soil. We used this method to measure the recovery of shredded office paper and pure medium fiber cellulose added to a Helvetia silt loam clay soil. This method consists of solvating cellulose from soil with 77% H₂SO₄ and analysis of the cellulose recovered by the phenol-sulfuric acid carbohydrate assay. Unlike previous related methods the modifications we propose allow good recovery of cellulose (~99%) and eliminate the need to autoclave the samples. We verified this method on soil spiked with up to 12% cellulose and found a good linear relationship between the amounts of cellulose added relative to that recovered. With proper fragmentation and dilution of the acid-treated soil samples, higher concentrations can be easily measured. We propose this technique as a robust and high throughput means to monitor the degradation of cellulose in paper spiked soil.     

Preparation of Cellulose/Xanthan Gum Composite Films and Hydrogels Using Ionic Liquid

This paper reports the preparation of cellulose/xanthan gum composite films and hydrogels through gelation with an ionic liquid. Mixtures of cellulose and xanthan gum in desired weight ratios with an ionic liquid, 1-butyl-3-methylimidazolium chloride (BMIMCl), were thinly placed on a Petri dish and heated at 100 °C for 9 h to obtain the solutions. Then, the solutions were left standing at room temperature for 1 day for the progress of gelation. The resulting ion gels were subjected to Soxhlet extraction with ethanol to remove BMIMCl, followed by drying under ambient conditions to obtain the composite films. The crystalline structures of the polysaccharides and the mechanical properties were evaluated by powder X-ray diffraction measurement and tensile testing of the films, respectively. The ion gels in various cellulose/xanthan gum weight ratios, which were prepared in a test tube by the same procedure, were immersed in water for the exchange of disperse media to obtain the cellulose/xanthan gum composite hydrogels. Water contents of all the materials were higher than 90 %. The mechanical properties of the hydrogels were evaluated by compressive testing.     

Preparation of Chitin/Cellulose Films Compatibilized with Polymeric Ionic Liquids

This paper reports the preparation of chitin/cellulose films compatibilized with polymeric ionic liquids. In-situ (co)polymerization of polymerizable ionic liquids, 1-(3-methacryloyloxypropyl)-3-vinylimidazolium bromide (1) and 1-methyl-3-vinylbenzylimidazolium chloride (3), was carried out in the presence of a radical initiator, AIBN, in the chitin/cellulose solution with ionic liquid solvents (1-butyl-3-methylimidazolium acetate and chloride, BMIMOAc and BMIMCl, respectively), followed by the appropriate procedure to give the desired films. The presence of the polymeric ionic liquid in the film was confirmed by the IR measurement. The powder X-ray diffraction analysis suggested that crystalline structures of the polysaccharides were largely disrupted in the film, as same as that of a chitin/cellulose film prepared by the AMIMOAc/BMIMCl system. These results were different from the XRD result of a chitin/cellulose film prepared by the 1-allyl-3-methylimidazolium bromide/BMIMCl system reported in our previous study, in which some crystalline structures were still remained in the film. Furthermore, the mechanical properties of the present films were evaluated by tensile testing, which were affected by the molar ratios of the polymeric ionic liquids to the polysaccharides and the compositional ratios of the two units 1 and 3.