共查询到20条相似文献,搜索用时 437 毫秒
1.
石油泄漏对海洋生态造成极大威胁。通过实验室模拟重油在海水中悬浮与扩散的情况,考察了膨润土在模拟海水中促进油滴分散的作用机制,以及振荡时间、膨润土表面特性和膨润土投加量对重油分散效率的影响。实验结果表明,2种膨润土颗粒均可以通过与重油形成聚结物(OMA)将油分散。改性膨润土(CTAB-B)与重油形成稳定OMA所需的时间远远小于未改性钠基膨润土(Na-B),形成时间分别为40、180min;CTAB-B与重油生成OMA的效率高于Na-B,在低膨润土投加量(为重油质量的10%)条件下,CTAB-B、Na-B与重油形成OMA的效率分别是70%和36%;Na-B参与形成的OMA结构单一,CTAB-B与重油形成多种OMA结构,油滴粒径有所增大,但油滴颗粒在水中的稳定性增强。研究结果对于海洋石油泄露的防治具有一定指导意义。 相似文献
2.
旋流分离器油水分离效率的模拟研究 总被引:1,自引:0,他引:1
采用计算流体力学的方法,探讨了操作条件和物料特性对旋流分离器分离油水效率的影响。旋流器为单锥双入口,其主直径为50 mm,锥角为5.5°。模拟过程中,采用商业用软件‘Fluent 6.3’中的雷诺应力模型和欧拉多相流模型来模拟不同条件下油水旋流分离器的分离性能。模拟结果表明,对于本研究的油水旋流分离器,最佳的分流比是10%,最佳的油滴浓度是0.5%(V/V)。在最佳的分流比和油滴浓度下,当进口流速为10.46 m/s时,油水旋流分离器可将15μm的油滴去除80%以上,油滴的分离界限粒径d50(50%的分离效率)为9.2μm。在模拟的基础上,用统计软件STATISTICA6.0对分离效率与操作条件和物料特性之间的关系进行拟合。通过拟合式预测的分离效率与实测值相吻合,误差小于15%。 相似文献
3.
4.
5.
6.
7.
电选法回收利用废印刷线路板 总被引:10,自引:0,他引:10
废印刷线路板含有多种有价值的物质,随意丢弃或处理处置方法不当既污染环境,又造成资源流失。采用剪切式破碎和电力分选技术对废印刷线路板的机械分离进行了研究。结果表明,电选法可以实现废印刷线路板中金属和玻璃纤维、树脂的分离;在实验的粒径范围内(-14+20目到-120+200目分为5个粒径级别),金属主要集中在-20+120目粒级范围内,且该粒级范围分选效果最好。 相似文献
8.
《环境工程学报》2015,(9)
改性粉煤灰基吸附剂作为烟气脱汞吸附剂,具有成本低的特点。为进一步研究改性粉煤灰基吸附剂脱汞的工业运行状况,设计了最大烟气流量为2 000 Nm3/h的中试实验。首先通过数值模拟方法研究燃煤烟气过程中吸附剂脱汞性能,分别研究了吸附剂粒径、烟气流量以及吸附剂料层厚度对脱汞效率的影响。研究发现,随着烟气流量的增加脱汞效率降低,烟气流量为2 000 Nm3/h时脱汞效率为74.26%。在中试实验中采用三段式脱汞工艺,脱汞吸附剂为卤素元素浸渍改性的粉煤灰基吸附剂,根据模拟结果设计了吸附剂粒径为25 mm,料层厚度为400 mm的实验参数。实验结果表明,三段式脱汞工艺在烟气流量为2 000 Nm3/h,其脱汞效率为78.8%,其中吸附剂的脱汞效率为68.90%,证明了改性粉煤灰基吸附剂在工业烟气脱汞工艺中具有良好作用。 相似文献
9.
10.
废印刷电路板的静电分选实验研究 总被引:1,自引:0,他引:1
金属与非金属材料的分离是回收利用废印刷电路板的关键环节。对废印刷电路板物料的静电分选进行了实验研究。实验以电压、辊筒转速、电晕电极与辊筒之间的距离、静电极位置、电晕电极位置、电晕电极数量等为考察因素,研究各因素对电选效果的影响规律。结果表明,影响金属与非金属材料分离的主要因素是电压、辊筒转速和电晕电极与辊筒之间的距离,对于-0.9 0.45mm的破碎物料,当电压为24kV,辊筒转速为15Hz(54.6r/min),电晕电极与辊筒之间的距离为5.2cm时,得到最大静电分选综合效率67.37%。 相似文献
11.
Árpád Ambrus 《Journal of environmental science and health. Part. B》2013,48(3):435-442
Abstract A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits. 相似文献
12.
造纸废水混凝处理中SFT助凝替代性研究 总被引:1,自引:0,他引:1
中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染 相似文献
13.
Janusz A. Pudykiewicz Anna S. Koziol 《Atmospheric environment (Oxford, England : 1994)》1998,32(24):5541
The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing. 相似文献
14.
介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠 相似文献
15.
不同泥源对厌氧氨氧化反应器启动的影响 总被引:2,自引:1,他引:1
采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。 相似文献
16.
活性炭三维电极法对印染废水的处理研究 总被引:4,自引:0,他引:4
对三维电极方法处理印染废水进行了实验研究,初步探讨了活性炭三维电极法处理印染废水的机理,对影响处理效果的各种要素,如反应时间、槽电压和pH值等进行了条件实验,得出了活性炭三维电极法处理印染废水的最佳运行条件为:停留时间120-180 min,槽电压25~30 V,进水pH值6.5~7.5。结果表明,该反应器能有效地降低废水色度,有较高的COD去除效率,并能提高印染废水的可生化性。 相似文献
17.
18.
以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径<1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径. 相似文献
19.
Volker Berding Stefan Schwartz Michael Matthies 《Environmental science and pollution research international》1999,6(1):37-43
The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters
(inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation,
on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency.
The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity
was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters),
and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity
to 961, and the maximal dimension is 21. 相似文献