Auto shredder residue recycling: Mechanical separation and pyrolysis

Directive 2000/53/EC sets a goal of 85% material recycling from end-of-life vehicles (ELVs) by the end of 2015. The current ELV recycling rate is around 80%, while the remaining waste is called automotive shredder residue (ASR), or car fluff. In Europe, this is mainly landfilled because it is extremely heterogeneous and often polluted with car fluids. Despite technical difficulties, in the coming years it will be necessary to recover materials from car fluff in order to meet the ELV Directive requirement. This study deals with ASR pretreatment and pyrolysis, and aims to determine whether the ELV material recycling target may be achieved by car fluff mechanical separation followed by pyrolysis with a bench scale reactor. Results show that flotation followed by pyrolysis of the light, organic fraction may be a suitable ASR recycling technique if the oil can be further refined and used as a chemical. Moreover, metals are liberated during thermal cracking and can be easily separated from the pyrolysis char, amounting to roughly 5% in mass. Lastly, pyrolysis can be a good starting point from a "waste-to-chemicals" perspective, but further research should be done with a focus on oil and gas refining, in order both to make products suitable for the chemical industry and to render the whole recycling process economically feasible.     

On the ASR and ASR thermal residues characterization of full scale treatment plant

In order to obtain 85% recycling, several procedures on Automotive Shredder Residue (ASR) could be implemented, such as advanced metal and polymer recovery, mechanical recycling, pyrolysis, the direct use of ASR in the cement industry, and/or the direct use of ASR as a secondary raw material. However, many of these recovery options appear to be limited, due to the possible low acceptability of ASR based products on the market. The recovery of bottom ash and slag after an ASR thermal treatment is an option that is not usually considered in most countries (e.g. Italy) due to the excessive amount of contaminants, especially metals. The purpose of this paper is to provide information on the characteristics of ASR and its full-scale incineration residues. Experiments have been carried out, in two different experimental campaigns, in a full-scale tyre incineration plant specifically modified to treat ASR waste.Detailed analysis of ASR samples and combustion residues were carried out and compared with literature data. On the basis of the analytical results, the slag and bottom ash from the combustion process have been classified as non-hazardous wastes, according to the EU waste acceptance criteria (WAC), and therefore after further tests could be used in future in the construction industry. It has also been concluded that ASR bottom ash (EWC – European Waste Catalogue – code 19 01 12) could be landfilled in SNRHW (stabilized non-reactive hazardous waste) cells or used as raw material for road construction, with or without further treatment for the removal of heavy metals. In the case of fly ash from boiler or Air Pollution Control (APC) residues, it has been found that the Cd, Pb and Zn concentrations exceeded regulatory leaching test limits therefore their removal, or a stabilization process, would be essential prior to landfilling the use of these residues as construction material.     

On-field investigation and process modelling of End-of-Life Vehicles treatment in the context of Italian craft-type Authorized Treatment Facilities

The present article analyses the current situation of End-of-Life-of-Vehicles (ELVs) management in Europe, with particular attention on Italian condition. Similarly to other European countries, metal recycling is the main activity of the whole system, but such situation is evolving due to the 2000/53/EC Directive, which sets out targets for Reuse, Recycling and Recovery of ELVs. Due to the relevance of the ELVs problem, in 2008 Italian Ministry of Environment subscribed a framework agreement with competent stakeholders as carmakers, dismantlers, shredders. The main result is an industrial plan to promote (amongst other objectives) technological progress for residual waste (Automotive Shredder Residue – ASR) treatment. According with Italian Trial 2006 analysis about ELVs, Reuse and Recycling rate is currently estimated to be about 81%.At the present time, dismantling plants constitute the first collection points for ELVs; for this reason, during 2009 an investigation has been done over a number of ten Authorized Treatment Facilities (ATFs) operating in Italy. The first step of the analysis was aimed to find out major practices and methods through observations of ATFs activities and interviews to operators. Furthermore, the depollution and dismantling treatments of about 70 different ELVs have been observed and timed in detail over a period of three months. The results included the identification of most relevant critical issues in ELVs treatment, such as distortions between scrapping activities and Directive’s regulation, and the assessment of the time and of the resources needed to perform each operation.In the second step of the survey, a process simulation model has been built on the basis of such data. The model was aimed to include the real variability and all the uncertainties that are typical of dismantling activities; it is intended as a tool for process layout planning and for its management. Some control parameters have been introduced; these are able to dynamically modify process path depending on ELVs queues and priorities. The model can also be used for the economic assessments of single operations or of the whole treatment activity.     

Review of Italian experience on automotive shredder residue characterization and management

Automotive Shredder Residue (ASR) is a special waste that can be classified as either hazardous or non hazardous depending on the amount of hazardous substances and on the features of leachate gathered from EN12457/2 test. However both the strict regulation concerning landfills and the EU targets related to End-of-Life Vehicles (ELVs) recovery and recycling rate to achieve by 2015 (Directive 2000/53/EC), will limit current landfilling practice and will impose an increased efficiency of ELVs valorization. The present paper considers ELVs context in Italy, taking into account ASRs physical–chemical features and current processing practice, focusing on the enhancement of secondary materials recovery. The application in waste-to-energy plants, cement kilns or metallurgical processes is also analyzed, with a particular attention to the possible connected environmental impacts. Pyrolysis and gasification are considered as emerging technologies although the only use of ASR is debatable; its mixing with other waste streams is gradually being applied in commercial processes. The environmental impacts of the processes are acceptable, but more supporting data are needed and the advantage over (co-)incineration remains to be proven.     

End-of-Life Vehicles management: Italian material and energy recovery efficiency

Each European Member State must comply with Directive 2000/53/EC recycling and recovery targets by 2015, set to 85% and 95%, respectively. This paper reports a shredder campaign trial developed and performed in Italy at the beginning of 2008. It turns out to be the first assessment about the critical aspects belonging to the Italian End-of-Life Vehicles (ELVs) reverse supply chain involving 18 dismantling plants, a shredder plant and 630 ELV representatives of different categories of vehicles treated in Italy during 2006. This trial aims at improving the experimental knowledge related to ELVs added waste, pre-treatment, part reuse, recycling and final metal separation and car fluff disposal. Finally, the study also focuses on the calculation of the effective Italian ELV recycling rate, which results equal to 80.8%, and auto shredder residue (ASR) characterization. According to the results obtained in this work, ASR still contains up to 8% of metals and 40% of polymers that could be recovered. Moreover, physical-chemical analysis showed a Lower Heat Value of almost 20,000 kJ/kg and revealed the presence of pollutants such as heavy metals, mineral oils, PCBs and hydrocarbons.     

Strategies for the enhancement of automobile shredder residues (ASRs) recycling: Results and cost assessment

With reference to the European regulation about the management of End-of-Life Vehicles (ELVs), Directive 2000/53/EC imposes the achievement of a recycling target of 85%, and 95% of total recovery by 2015. Over the last few years many efforts have been made to find solutions to properly manage the waste coming from ELVs with the aim of complying with the targets fixed by the Directive.This paper focuses on the economical evaluation of a treatment process, that includes physical (size and density), magnetic and electrical separations, performed on the light fraction of the automobile shredder residue (ASR) with the aim of reducing the amount of waste to dispose of in a landfill and enhancing the recovery of valuable fractions as stated by the EU Directive. The afore mentioned process is able to enhance the recovery of ferrous and non-ferrous metals of an amount equal to about 1% b.w. (by weight) of the ELV weight, and to separate a high energetic-content product suitable for thermal valorization for an amount close to (but not higher than) 10% b.w. of the ELV weight.The results of the economical assessment led to annual operating costs of the treatment ranging from 300,000 €/y to 350,000 €/y. Since the considered plant treats about 13,500 metric tons of ASR per year, this would correspond to an operating cost of approximately 20–25 €/t. Taking into account the amount and the selling price of the scrap iron and of the non magnetic metal recovered by the process, thus leading to a gain of about 30 €/t per ton of light ASR treated, the cost of the recovery process is balanced by the profit from the selling of the recovered metals. On the other hand, the proposed treatment is able to achieve the fulfillment of the targets stated by Directive 2000/53/EC concerning thermal valorization and reduce the amount of waste generated from ELV shredding to landfill.     

Dynamic flow analysis of current and future end-of-life vehicles generation and lead content in automobile shredder residue

Since end-of-life vehicles (ELVs) contain toxic substances, they have to be treated properly. The purpose of this study was to obtain useful information for ELV management from the viewpoint of toxicity. We focused on lead as a representative toxic substance contained in vehicles and investigated the dynamic substance flow of lead contained in ELVs and its content in automobile shredder residue (ASR). A population balance model was used to estimate the number of ELVs generated between FYs (fiscal year) 1990–2020, employing a Weibull distribution for the lifespan distribution. Sixteen lead-containing components of the vehicle were considered. It was estimated that the annual number of ELVs generated would be 2.9 million as of FY2020. The results implied that it is hard to remove Pb completely. This is because 5,000–11,000 t-Pb will still remain in vehicles in use in FY2020 even though most components in new model vehicles could be replaced by lead-free alternatives. As of FY2010, the substance flow showed that Pb contained in ELVs amounted to 4,600–5,700 t-Pb. Of this, 13.2–14.0 % was contained in ASR. The Pb content in ASR could be dramatically decreased by FY2020, but it will continue to contain 240–420 mg-Pb/kg if the treatment system is not improved.     

End-of-life vehicle recycling and automobile shredder residue management in Japan

The Japanese Government introduced the Law on Recycling of End-of-Life Vehicles (ELV Recycling Law) in 2002. This law requires manufacturers to retrieve chlorofluorocarbons (CFCs), airbags, and automobile shredder residue (ASR) from ELVs and to properly recycle the remaining materials. This framework is compared with European ELV directives. Pilot-scale incineration plant testing has revealed a greater formation of by-product persistent organic pollutants (POPs) during the primary combustion of ASR compared to normal municipal solid waste. This may be attributed to the abundance of chlorine, Cu, and Fe in ASR, as Cu and Fe have been found to catalyze the formation of POPs under certain conditions. However, most by-product POPs were destroyed by the secondary combustion, and almost all were removed after flue gas treatment. The direct melting system is a shaft-type gasification and melting technology that has proved effective in many municipal solid waste applications. This system can be applied to ASR recycling for effective decomposition of brominated flame retardants and polybrominated dioxins.     

Aluminium flows in vehicles: enhancing the recovery at end-of-life

The transportation sector constitutes the major end-use market for aluminium-containing products and expectations for the future do indicate that aluminium will increase at 140 kg per vehicle. Moreover, up to 75 % aluminium recycled in Europe is used in transportation: thus, metal scrap recovered from ELVs is a key lever to act for closing material cycles. However, although the management chain of ELVs has an established procedure and aluminium scrap is usually recovered in shredding plants, a considerable fraction of the metal particles ends up in the light fraction called car fluff and is then landfilled. In this study we investigated potential of enhancing the recovery of aluminium scrap from the light fluff treatment. With this goal, the quantity of aluminium embedded in the Italian transport sector in the last 62 years was estimated, and a campaign of characterization in size and shape distribution of aluminium particles in the light fluff output has been carried out. The results estimated up to about 560,000 tons of metal are potentially recoverable from the treatment of light fluff at current operating conditions, but relevant improvements may be achieve when size and shape distribution criteria are adopt to implement eddy currents separation for a quantitative metal recovery.     

The development and prospects of the end-of-life vehicle recycling system in Taiwan

Automobiles usually contain toxic substances, such as lubricants, acid solutions and coolants. Therefore, inappropriate handling of end-of-life vehicles (ELVs) will result in environmental pollution. ELV parts, which include metallic and non-metallic substances, are increasingly gaining recycling value due to the recent global shortage of raw materials. Hence, the establishment of a proper recycling system for ELVs will not only reduce the impact on the environment during the recycling process, but it will also facilitate the effective reuse of recycled resources. Prior to 1994, the recycling of ELVs in Taiwan was performed by related operators in the industry. Since the publishing of the “End-of-life vehicle recycling guidelines” under the authority of the Waste Disposal Act by the Environmental Protection Administration (EPA) in 1994, the recycling of ELVs in Taiwan has gradually become systematic. Subsequently, the Recycling Fund Management Board (RFMB) of the EPA was established in 1998 to collect a Collection–Disposal–Treatment Fee (recycling fee) from responsible enterprises for recycling and related tasks. Since then, the recycling channels, processing equipment, and techniques for ELVs in Taiwan have gradually become established. This paper reviews the establishment of the ELV recycling system, analyzes the current system and its performance, and provides some recommendations for future development. The reduction of auto shredder residue (ASR) is a key factor in maximizing the resource recovery rate and recycling efficiency. The RFMB needs to provide strong economic incentives to further increase the recycling rate and to encourage the automobile industry to design and market greener cars.     

Management status of end-of-life vehicles and characteristics of automobile shredder residues in Korea

An end-of-life vehicle (ELV) is dismantled to recover and recycle any re-usable parts, then shipped to the shredding facility for further recovery of iron with any remaining Automobile Shredder Residue (ASR) to be considered as wastes and to be disposed of by either thermal treatment or landfill. Overall ELVs management status in Korea, including recycling resulting from the dismantling processes, was surveyed using some questionnaires given to dismantlers and other available information to provide some feasible means for future treatment. The averaged recycle rate in the dismantling stage showed a value of 44% and the rest of an ELV was then compressed and transported to shredding companies to recover mainly the iron content which averaged 38.7% of the mass of a new vehicle. The non-ferrous metals such as copper, antimony, zinc and aluminum accounted for only 1.5%. The Shredder dusts (SDs) were found to be composed of light and heavy fluffs and soil/dust and amounted to 15.8% based on the mass of a new vehicle. Dumping of fluff and inorganic residues into a landfill site, however, will be restricted when new regulations are implemented to reduce the disposal amount to less than 5% of a new car as done in European countries and Japan. The detailed characteristics of SDs were investigated to provide an idea of how to treat them in order to meet a future expected enforcement.     

Automotive shredder residue (ASR) characterization for a valuable management

Car fluff is the waste produced after end-of-life-vehicles (ELVs) shredding and metal recovery. It is made of plastics, rubber, glass, textiles and residual metals and it accounts for almost one-third of a vehicle mass. Due to the approaching of Directive 2000/53/EC recycling targets, 85% recycling rate and 95% recovery rate in 2015, the implementation of automotive shredder residue (ASR) sorting and recycling technologies appears strategic. The present work deals with the characterization of the shredder residue coming from an industrial plant, representative of the Italian situation, as for annual fluxes and technologies involved. The aim of this study is to characterize ASR in order to study and develop a cost effective and environmentally sustainable recycling system. Results show that almost half of the residue is made of fines and the remaining part is mainly composed of polymers. Fine fraction is the most contaminated by mineral oils and heavy metals. This fraction produces also up to 40% ashes and its LHV is lower than the plastic-rich one. Foam rubber represents around half of the polymers share in car fluff. Moreover, some chemical–physical parameters exceed the limits of some parameters fixed by law to be considered refuse derived fuel (RDF). As a consequence, ASR needs to be pre-treated in order to follow the energy recovery route.     

Washing treatment of automotive shredder residue (ASR)

Worldwide, the amount of end-of-life vehicles (ELVs) reaches 50 million units per year. Once the ELV has been processed, it may then be shredded and sorted to recover valuable metals that are recycled in iron and steelmaking processes. The residual fraction, called automotive shredder residue (ASR), represents 25% of the ELV and is usually landfilled. In order to deal with the leachable fraction of ASR that poses a potential threat to the environment, a washing treatment before landfilling was applied. To assess the potential for full-scale application of washing treatment, tests were carried out in different conditions (L/S = 3 and 5 L/kg_TS; t = 3 and 6 h). Moreover, to understand whether the grain size of waste could affect the washing efficiency, the treatment was applied to ground (<4 mm) and not-ground samples. The findings obtained revealed that, on average, washing treatment achieved removal rates of more than 60% for dissolved organic carbon (DOC), chemical oxygen demand (COD) and total Kjeldahl nitrogen (TKN). With regard to metals and chlorides, sulphates and fluoride leachable fraction, a removal efficiency of approximately 60% was obtained, as confirmed also by EC values. The comparison between the results for ground and not-ground samples did not highlight significant differences.     

Scenario analysis for recovery of rare earth elements from end-of-life vehicles

End-of-life vehicles (ELVs) are increasingly being recognized as a possible future resource pool for rare earth elements (REEs). This study provides the amount of REEs that can be recovered from ELVs in Japan based on dismantling survey, chemical identification and substance flow analysis. The REEs were quantified from common passenger vehicles and hybrid electric vehicles. We targeted 17 REEs in estimation of REE contents in ELVs. Four scenarios were developed to explore the recovery of REEs from ELVs. In these scenarios, NiMH batteries and motors containing NdFeB magnets were identified as target components due to they are main REEs carriers; we focused on interpretation of neodymium (Nd) and dysprosium (Dy) owing to they are two of the most critical REEs. The results suggest that 2700 (±500) tons of REEs can be recovered, of which 520 (±100) tons and 31 (±7) tons will be contributed by Nd and Dy in 2030. Meanwhile, the Dy recovered from ELVs can satisfy 23 % (±6 %) of the demand for NdFeB magnets and NiMH battery cells in automobile production of Japan; the Nd recovered from ELVs can satisfy 49 % (±9 %) of the production demands.     

Status of recycling end-of-life vehicles and efforts to reduce automobile shredder residues in Korea

The present end-of-life vehicle (ELV) recycle rate and management status during the dismantling stage were investigated to aid the establishment of policies for the management of ELVs by surveying information and using the results gained from questionnaires given to dismantlers. The average recycle rate at the dismantling stage was 44% of the mass of a new vehicle and the rest of the ELV was then compressed and transported to shredding companies to recover mainly the iron content, which averaged 38.7% of the mass of a new vehicle. Nonferrous metals such as copper, antimony, zinc, and aluminum accounted for only 1.5%. The automobile shredder residues (ASRs) were composed of light and heavy fluffs and soil/dust and amounted to 15.8% based on the mass of a new vehicle. The dumping of fluff and inorganic residues in landfill sites, however, will be restricted when new regulations are implemented to reduce the disposal amount to less than 5% of a new car, as has been done in European countries and in Japan. The detailed characteristics of ASR were investigated to suggest appropriate means of treatment such as volume reduction or the utilization of thermal technologies to meet future expected enforcement. Also, some concerns on hazardous pollutant release such as that of dioxins while utilizing such thermal treatment methods were considered. The present on-going research and development projects to meet such future management targets are also introduced.     

Sustainable design for automotive products: Dismantling and recycling of end-of-life vehicles

The growth in automotive production has increased the number of end-of-life vehicles (ELVs) annually. The traditional approach ELV processing involves dismantling, shredding, and landfill disposal. The “3R” (i.e., reduce, reuse, and recycle) principle has been increasingly employed in processing ELVs, particularly ELV parts, to promote sustainable development. The first step in processing ELVs is dismantling. However, certain parts of the vehicle are difficult to disassemble and use in practice. The extended producer responsibility policy requires carmakers to contribute in the processing of scrap cars either for their own developmental needs or for social responsibility. The design for dismantling approach can be an effective solution to the existing difficulties in dismantling ELVs. This approach can also provide guidelines in the design of automotive products. This paper illustrates the difficulty of handling polymers in dashboards. The physical properties of polymers prevent easy separation and recycling by using mechanical methods. Thus, dealers have to rely on chemical methods such as pyrolysis. Therefore, car designers should use a single material to benefit dealers. The use of materials for effective end-of-life processing without sacrificing the original performance requirements of the vehicle should be explored.     

Recycling plastics from automotive shredder residues: a review

Automotive shredder residue (ASR) is an inevitable by-product of car recycling, i.e. removal of all liquids and hazardous or valuable components from the car and shredding of the hulk, followed by the recovery of steel, iron, and non-ferrous scrap. The European Union (EU) ELV Directive requires attaining higher recovery and recycling rates, resulting in a reduction of the amount of ASR going to landfill. The most plausible methods to achieve a considerable reduction of ASR are as follows: either recycling of separated materials and dismantled bulky parts, such as bumpers, dashboards, cushions, and front and rear windows, or else systematic sorting of the commingled and size-reduced materials, resulting from shredding. After a brief comparison of the actual situation in the EU, the USA, and Japan, the characteristics of actual ASR are reviewed, as well as some of the most prominent efforts made to separate and recycle specific fractions, such as polyolefins, ABS, or polyurethane. Attention is paid to some major players in the EU and to some of the pitfalls that besiege these ventures.     

Integrated municipal solid waste treatment using a grate furnace incinerator: the Indaver case

An integrated installation for treatment of municipal solid waste and comparable waste from industrial origin is described. It consists of three grate furnace lines with flue gas treatment by half-wet scrubbing followed by wet scrubbing, and an installation for wet treatment of bottom ash. It is demonstrated that this integrated installation combines high recovery of energy (40.8% net) with high materials recovery. The following fractions were obtained after wet treatment of the bottom ash: ferrous metals, non-ferrous metals, three granulate fractions with different particle sizes, and sludge. The ferrous and non-ferrous metal fractions can both be recycled as high quality raw materials; the two larger particle size particle fractions can be applied as secondary raw materials in building applications; the sand fraction can be used for applications on a landfill; and the sludge is landfilled. For all components of interest, emissions to air are below the limit values. The integrated grate furnace installation is characterised by zero wastewater discharge and high occupational safety. Moreover, with the considered installation, major pollutants, such as PCDD/PCDF, Hg and iodine-136 are to a large extent removed from the environment and concentrated in a small residual waste stream (flue gas cleaning residue), which can be landfilled after stabilisation.     

Brominated flame retardants and heavy metals in automobile shredder residue (ASR) and their behavior in the melting process

The End-of-life Vehicles Recycling Act went into effect on January 1, 2005, in Japan and requires the proper treatment of airbags, chlorofluorocarbons (CFCs), and automobile shredder residue (ASR). The need for optimal treatment and recycling of ASR, in particular, has been increasing year after year because ASR is regarded as being difficult to treat. Dioxin-related compounds, brominated flame retardants (BFRs), heavy metals, chlorine and organotin compounds are all present in high concentrations in ASR. The authors conducted ASR melting treatment tests using a 10-tons/day-scale direct melting system (DMS), which employs shaft-type gasification and melting technology. The results obtained showed that dioxin-related compounds and BFRs were decomposed by this melting treatment. The high-temperature reducing atmosphere in the melting furnace moved volatile heavy metals such as lead and zinc into the fly ash where they were distributed at a rate of more than 90% of the input amount. This treatment was also found to be effective in the decomposition of organotin, with a rate of decomposition higher than 99.996% of the input amount. Via the recovery of heavy metals concentrated in the fly ash, all the products discharged from this treatment system were utilized effectively for the complete realization of an ASR recycling system that requires no final disposal sites.     

Mobility of organic carbon from incineration residues

Dissolved organic carbon (DOC) may affect the transport of pollutants from incineration residues when landfilled or used in geotechnical construction. The leaching of dissolved organic carbon (DOC) from municipal solid waste incineration (MSWI) bottom ash and air pollution control residue (APC) from the incineration of waste wood was investigated. Factors affecting the mobility of DOC were studied in a reduced 2(6-1) experimental design. Controlled factors were treatment with ultrasonic radiation, full carbonation (addition of CO2 until the pH was stable for 2.5h), liquid-to-solid (L/S) ratio, pH, leaching temperature and time. Full carbonation, pH and the L/S ratio were the main factors controlling the mobility of DOC in the bottom ash. Approximately 60 weight-% of the total organic carbon (TOC) in the bottom ash was available for leaching in aqueous solutions. The L/S ratio and pH mainly controlled the mobilization of DOC from the APC residue. About 93 weight-% of TOC in the APC residue was, however, not mobilized at all, which might be due to a high content of elemental carbon. Using the European standard EN 13 137 for determination of total organic carbon (TOC) in MSWI residues is inappropriate. The results might be biased due to elemental carbon. It is recommended to develop a TOC method distinguishing between organic and elemental carbon.