超声辐射法降解废水中的二甲苯、苯酚和丙烯腈

采用频率为20kHz的超声波处理二甲苯、丙稀腈、苯酚溶液。实验结果表明,在二甲苯初始质量浓度为27．6mg／L、H2O2质量浓度为1．68g／L、溶液温度为25℃、声强为141．32W／cm^2、辐射全程时间为60min的条件下,二甲苯降解率可达99．20％;在丙烯腈初始质量浓度为100．0mg／L、通氧量为15mL／rain、溶液温度为28℃、声强为141．32W／cm^2、辐射全程时间为30rain的条件下,丙烯腈降解率可达98．20％;在苯酚初始质量浓度为20．0mg／L、H202质量浓度为1．50g／L、FeSO4质量浓度为0．22g／L、溶液温度为28℃、声强为48．92W／cm^2、辐射全程时间为40rain的条件下,苯酚降解率可达99．81％。     

Ti/MnO2/PbO2电极的制备及电催化降解罗丹明B

采用电沉积法制备了Ti／MnO2／PbO2电极,并用其对质量浓度为20mg／L的罗丹明B模拟废水进行了电催化降解实验。实验结果表明：原水pH为4．95,无须调节废水的pH;最佳电解实验条件为：支持电解质NazSO4浓度0．09mol／L,电解电流密度40mA／cm^2,处理时间40min,在此条件下罗丹明B的去除率接近100％。     

改进铁氧体共沉淀法去除污泥浸出液中的铜锌

采用改进铁氧体共沉淀法,用石灰乳溶液作中和剂,从污泥浸出液中去除铜、锌。实验结果表明,在混合液．pH为8．9、反应温度为室温、反应时间为1h、FeCl3和FeSO4初始浓度分别为0．1068mol／L和0．0534mol／L、n（Fe^3＋）：[n（Cu^2＋）＋n（Zn^2＋）]=10的最佳工艺条件下,浸出液中铜去除率为94．5％,锌去除率为98．0％。     

三维电极法处理氯苯废水

采用三维电极法处理氯苯废水。研究了外加槽电流、停留时间、氯苯初始质量浓度、废水初始pH等对氯苯去除率的影响。实验结果表明：外加槽电流增大,氯苯去除率明显提高;停留时间延长,氯苯去除率提高;而废水初始pH和氯苯初始质量浓度的变化对氯苯去除率影响不大。在外加槽电流为2．0A、氯苯初始质量浓度为1～200mg／L、停留时间为40～60min、废水初始pH为7的条件下,氯苯去除率达83％以上。并探讨了氯苯的电化学降解机理。     

Fenton试剂降解选矿废水中残余黄药

采用Fenton试剂处理选矿废水中残余的黄药,分别考察了氧化时间、反应初始pH、Fe^2 浓度及H2O2用量对黄药降解效果的影响;用正交实验确定了4个因素的最佳条件。结果表明,反应初始pH和H2O2用量是影响黄药去除效果的主要因素。氧化时间为60min、反应初始pH为4、Fe^2 质量浓度为20mg／L、H2O2质量浓度为20mg／L、黄药质量浓度为：125mg/L时,黄药的去除率达到99．5％,COD去除率为87．5％。     

UV/Fenton氧化-混凝联合工艺处理含酚废水

采用UV／Fenton氧化-混凝联合工艺对模拟苯酚废水进行处理,探讨了UV／Fenton预氧化程度和混凝处理条件对模拟苯酚废水处理效果的影响。结果表明,采用混凝处理,COD去除率仅为14．1％;当UV／Fenton预氧化处理过程中H2O2的质量浓度为150～300mg／L时,废水的混凝性能可提高1．5倍以上;当H2O2质量浓度为450mg／L、光反应时间为30min时,采用UV／Fenton氧化一混凝工艺联合处理后COD去除率达82．7％。苯酚废水采用UV／Fenton预氧化处理后,进行混凝处理过程的适宜pH为6．5,混凝剂Fe^3 的适宜质量浓度为500mg／L.     

聚合氯化铝锌絮凝剂的制备及其性能

用在AlCl,与ZnCl2溶液中加NaOH溶液的方法制备无机高分子絮凝剂聚合氯化铝锌（PAZC）,通过正交实验确定的最佳制备条件为：反应时间10min、碱化度2．2、氯化铝浓度0．5mol／L、NaOH溶液浓度0．5mol／L。在n（Zn）：n（Al）=0．6、水样pH=7．8、PAZC加入量为5mg／L的条件下,浊度和COD去除率分别为98．9％和88．2％。PAZC与聚合氯化铝对各种工业废水的处理效果比较结果表明,PAZC对各种工业废水的处理效果较好。从废水处理成本来看,PAZC具有较好的经济效益。     

污泥活性炭的制备及其对溶液中Cr6+的吸附

以城市污水厂剩余污泥为原料,采用ZnCl2作活化剂,热解制备污泥活性炭。实验结果表明,制备污泥活性炭的最佳条件热解温度为550℃,ZnCl2溶液浓度为3mol／L,ZnCl2溶液体积与污泥质量比（mL／g）为2．5：1,热解时间为25min。用所制备的污泥活性炭吸附溶液中的Cr6＋最佳吸附条件为：吸附时间90min,Cr6＋初始质量浓度50mg／L,污泥活性炭加入量0．2g,溶液pH2,在此条件下,Cr6＋去除率达99．9％。污泥活性炭对溶液中Cr6＋的吸附等温线属于I型,等温吸附方程可用Langmuir模型和Freundlich模型来拟合。     

催化臭氧氧化法处理甲醛废水

用异丙醇钛盐表面改性法制备TiO2／SiO2催化剂，对甲醛废水进行催化臭氧氧化处理。通过比表面积的BET测定法、X射线衍射和拉曼光谱等分析方法对TiO2／SiO2催化剂进行了表征，考察了TiO2／SiO2催化剂加入量、臭氧流量及溶液pH等因素对甲醛催化臭氧氧化效果的影响。实验结果表明，在SiO2表面，TiO2微晶粒子以锐钛矿型高度分散；在甲醛质量浓度700mg／L、COD1000mg／L、TiO2／SiO2催化剂加入量2．0g、臭氧流量2．5mg／min、溶液pH8．5的条件下，催化臭氧氧化反应30min后，甲醛质量浓度由700mg／L降至39mg／L，COD去除率认到87．5％．     

交联阳离子淀粉的合成及其对重金属离子的吸附

通过正交实验合成了取代度为0．568的交联阳离子淀粉。考察了溶液pH、螯合剂用量、重金属离子初始浓度对交联阳离子淀粉去除重金属离子效果的影响。当重金属离子初始质量浓度为50mg／L、螯合剂投加量为0．5g／U时,Pb^2 ,Cu^2 ,Cr^3 在溶液pH为6时的去除率达到最高,分别为97．94％,99．46％,84．30％,而Cd^ 在溶液pH为7时的去除率达到最高,为99．36％。实验结果表明,交联阳离子淀粉是一种有效去除废水中重金属的处理剂。     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

四氮唑废水处理工艺设计

高浓度、高盐分的四氮唑生产废水通过三效蒸发浓缩,馏出液经铁炭氧微电解和混凝预处理,再采用水解酸化一接触氧化一反应二沉主体组合工艺进行处理。研究了该工艺所需构筑物和设备的设计与选型。该工艺在正常运行条件下,处理后出水pH6～9,COD 302mg／L,BOD5 108mg／L,SS30mg／L,色度36倍,水质达到GB8978--1996（污水综合排放标准》三级标准。     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Does Soil Acidification Affect Spruce Needle Chemical Composition and Tree Growth?

In 1994, a large survey of soil chemistry was undertaken in thecounty of Värmland in central Sweden (Lundström et al., 1998).The southern part of the county was affected by soilacidification whereas there were no such indications in thenorthern part. To investigate the influence of soil chemistryon the trees at the specific sites, the survey was continued byan analysis of needle chemistry (Norway spruce) which wasundertaken at 150 of the 180 sites, and of tree growth at 65 ofthe 180 sites. Growth was expressed as a ratio between expectedgrowth, estimated with a national, empirical growth model, andthe growth observed in the field. In statistical analyses,using rank correlation, PCA and PLS, there were only weakindications of an influence of soil chemistry on needlechemistry and on tree growth. A moderate correlation betweennitrogen and sulphur in needles was found, which wasinterpreted as an effect of deposition and of processes in thetree canopy. No obvious regional pattern of the growth ratiowas found, in contrast to the clear pattern of soilacidification. The statistical analysis could not with anycertainty point out any of the soil chemistry variables asespecially important for the tree growth ratio.     

Solubility and Potential Mobility of Heavy Metals in Two Contaminated Urban Soils from Stockholm,Sweden

The solubility and potential mobility of heavy metals (Cd, Cu,Hg, Pb and Zn) in two urban soils were studied by sequential andleaching extractions (rainwater). Compared to rural (arable) soils on similar parent material, the urban soils were highlycontaminated with Hg and Pb and to a lesser extent also with Cd,Cu and Zn. Metal concentrations in rainwater leachates were related to sequential extractions and metal levels reported fromStockholm groundwater. Cadmium and Zn in the soils were mainly recovered in easily extractable fractions, whereas Cu and Pb were complex bound. Concentrations of Pb in the residual fractionwere between two- and eightfold those in arable soils, indicatingthat the sequential extraction scheme did not reflect the solidphases affected by anthropogenic inputs. Cadmium and Zn conc. inthe rainwater leachates were within the range detected in Stockholm groundwater, while Cu and Pb conc. were higher, whichsuggests that Cu and Pb released from the surface soil were immobilised in deeper soil layers. In a soil highly contaminatedwith Hg, the Hg conc. in the leachate was above the median concentration, but still 50 times lower than the max concentration found in groundwater, indicating the possibilityof other sources. In conclusion, it proved difficult to quantitatively predict the mobility of metals in soils by sequential extractions.     

High Immobilization of NH4+ in Danish Heath Soil Related to Succession,Soil and Nutrients: Implications for Critical Loads of N

During recent decades heathlands havechanged into grasslands in regions with high atmosphericnitrogen deposition. In regions with intermediatedeposition level (e.g., Denmark) changes have been lesspronounced which may be due to delay or decrease inresponse of the ecosystem. The mor layer (O horizon) mayplay an important role for this delay due to high sinkstrength for N. In this study, the capacity for netNH₄ ⁺ immobilization and mineralization wasstudied during short- and long-term incubations (2–36 days)of mor samples from Danish dry inland heaths. High short-term capacity for net NH₄ ⁺ immobilization wasfound to be a general characteristic of Danish heath morlayers both under heather (Calluna vulgaris) andcrowberry (Empetrum nigrum ssp nigrum), the latterdominating late stages in heathland succession. The netNH₄ ⁺ immobilization was higher under youngcompared to old or dead vegetation, and higher on lessnutrient poor soils than on extremely nutrient poor soils.The addition of N, P and C stimulated CO₂ productionand net NH₄ ⁺ immobilization, but not net Nmineralization. The immobilization of ¹⁵NH₄ ⁺caused release of dissolved organic N, increased N anddecreased C/N ratio in the microbial biomass, and indicatedgrowth of microorganisms with other metabolic abilitiesthan the indigenous population. No evidence was obtained ofstabilization of immobilized ¹⁵NH₄ ⁺ intosoil organic matter during the experiment. On background ofthe results and current knowledge it was concluded that therecognition of the high capacity for net NH₄ ⁺immobilization in mor layers does not allow for a raiseof critical loads for N for northern dry inland heaths.     

Biodegradation of Injection Molded Starch-Poly (3-hydroxybutyrate-co-3-hydroxyvalerate) Blends in a Natural Compost Environment

Injection molded specimens were prepared by blending poly (hydroxybutyrate-co-valerate) (PHBV) with cornstarch. Blended formulations incorporated 30% or 50% starch in the presence or absence of poly-(ethylene oxide) (PEO), which enhances the adherence of starch granules to PHBV. These formulations were evaluated for their biodegradability in natural compost by measuring changes in physical and chemical properties over a period of 125 days. The degradation of plastic material, as evidenced by weight loss and deterioration in tensile properties, correlated with the amount of starch present in the blends (neat PHBV < 30% starch < 50% starch). Incorporation of PEO into starch-PHBV blends had little or no effect on the rate of weight loss. Starch in blends degraded faster than PHBV and it accelerated PHBV degradation. Also, PHBV did not retard starch degradation. After 125 days of exposure to compost, neat PHBV lost 7% of its weight (0.056% weight loss/day), while the PHBV component of a 50% starch blend lost 41% of its weight (0.328% weight loss/day). PHB and PHV moieties within the copolymer degraded at similar rates, regardless of the presence of starch, as determined by ¹H-NMR spectroscopy. GPC analyses revealed that, while the number average molecular weight (Mn) of PHBV in all exposed samples decreased, there was no significant difference in this decrease between neat PHBV as opposed to PHBV blended with starch. SEM showed homogeneously distributed starch granules embedded in a PHBV matrix, typical of a filler material. Starch granules were rapidly depleted during exposure to compost, increasing the surface area of the PHBV matrix.