Oxidative treatment of simulated dyehouse effluent by uv and near-UV light assisted Fenton's reagent

UV/Fenton, near-UV-visible/Fenton, dark Fenton, and H₂O₂/UV reactions have been used to treat simulated dyehouse effluents representing wastewater from the textile dyeing and rinsing process. Experiments were carried out in a lab - scale photochemical reactor using concentrations of 0.5–25 mM H₂O₂, 0.04-0.5 mM Fe²⁺-ion and different dilutions of textile wastewater. To assess the extent of mineralization, decolourization kinetics and the effect of different fight sources on treatment efficiency, DOC, optical density at 254 nm and 600 nm wavelength and residual H₂O₂ concentrations were measured during the course of the advanced oxidation reactions. Comparative evaluation of the obtained results revealed that the decolourization rate increased with applied H₂O₂ and Fe²⁺-ion dose as well as the strength of the synthetic textile wastewater. The best results were obtained by the near - UV/visible/Fenton process with a decolourization rate constant of 1.57 min⁻¹, a UV_254nm reduction of 97% and a DOC removal of 41% at relatively low doses of the H₂O₂ oxidant and Fe²⁺-ion catalyst within 60 min treatment time.     

Comparative studies of the Fe3+/2+-UV, H2O2-UV, TiO2-UV/vis systems for the decolorization of a textile dye X-3B in water

The degradation of a common textile dye, Reactive-brilliant red X-3B, by several advanced oxidation technologies was studied in an air-saturated aqueous solution. The dye was resistant to the UV illumination (wavelength λ  320 nm), but was decolorized when one of Fe³⁺, H₂O₂ and TiO₂ components was present. The decolorization rate was observed to be quite different for each system, and the relative order evaluated under comparable conditions followed the order of Fe²⁺–H₂O₂–UV  Fe²⁺–H₂O₂ > Fe³⁺–H₂O₂–UV > Fe³⁺–H₂O₂ > Fe³⁺–TiO₂–UV > TiO₂–UV > Fe³⁺–UV > TiO₂–visible light (λ  450 nm) > H₂O₂–UV > Fe²⁺–UV. The mechanism for each process is discussed, and linked together for understanding the observed differences in reactivity.     

硝基苯类废水的全混态零价铁-芬顿组合预处理工艺优化与工程验证

针对企业硝基氯苯装置产生的高毒性、难降解的硝基苯类废水,开发出全混态零价铁-芬顿组合预处理工艺,并分别优化了零价铁还原和芬顿氧化的工艺条件。结果表明,pH为2.0、零价铁投加量为220 mg/L时,废水中硝基苯类物质的去除率可达98.5%以上。出水pH约为3.0,继续投加3000 mg/L的H₂O₂,Fe²⁺投加比按C(Fe²⁺,mg/L):C(H₂O₂,mg/L)=1:10,1 h内COD去除率可达90%以上,且B/C由0.08提高到0.45。可见该组合预处理工艺可大幅削减废水毒性、改善可生化性,且直接运行成本仅为26.28元/吨,具有良好的环境和经济效益。     

A hybrid fenton oxidation-microbial treatment for soil highly contaminated with benz(a)anthracene

In order to mitigate the strong microbial resistance of benz(a)anthracene [B(a)A] in soil, a hybrid treatment of Fenton oxidation followed microbial culture was carried out. Based on optimal Fenton oxidation, i.e., 1.0 ml of ethanol, 0.2 ml of 0.5 M Fe²⁺, and 0.3 ml of 30% H₂O₂ per 1 g of 500 mg B(a)A/kg soil, about 43% of B(a)A-7,12-dione was generated during oxidation of 97% B(a)A. When the comparative biodegradability between B(a)A-contaminated soil and B(a)A-contaminated soil after Fenton oxidation was examined, it was found that 98% of B(a)A-7,12-dione degraded after 63 d in comparison with only 12% of B(a)A over the same period; results demonstrating that Fenton oxidation enhances biodegradability of B(a)A through B(a)A-7,12-dione.     

Sequential photochemical-biological degradation of chlorophenols

UV/TiO₂/H₂O₂, UV/TiO₂ and UV/H₂O₂ were compared as pre-treatment processes for the detoxification of mixtures of 4-chlorophenol (4CP), 2,4-dichlorophenol (DCP), 2,4,6-trichlorophenol (TCP) and pentachlorophenol (PCP) prior to their biological treatment. When each chlorophenol was initially supplied at 50 mg l⁻¹, UV/TiO₂/H₂O₂ treatment supported the highest pollutant removal, COD removal, and dechlorination efficiencies followed by UV/TiO₂ and UV/H₂O₂. The remaining toxicity to Lipedium sativum was similar after all pre-treatments. Chlorophenol photodegradation was always well described by a first order model kinetic (r² > 0.94) and the shortest 4CP, DCP, TCP and PCP half-lives of 8.7, 7.1, 4.5 and 3.3 h, respectively, were achieved during UV/TiO₂/H₂O₂ treatment. No pollutant removal was observed in the controls conducted with H₂O₂ or TiO₂ only. Inoculation of all the photochemically pre-treated mixtures with activated sludge microflora was followed by complete removal of the remaining pollutants. Combined UV/TiO₂/H₂O₂-biological supported the highest detoxification, dechlorination (99%) and COD removal (88%) efficiencies. Similar results were achieved when each chlorophenol was supplied at 100 mg l⁻¹. COD and Cl mass balances indicated UV, UV/H₂O₂, and UV/TiO₂ treatments lead to the formation of recalcitrant photoproducts, some of which were chlorinated.     

Photocatalytic bacterial inactivation by polyoxometalates

The photocatalytic inactivation (PCI) of Escherichia coli (Gram-negative) and Bacillus subtilis (Gram-positive) was performed using polyoxometalate (POM) as a homogeneous photocatalyst and compared with that of heterogeneous TiO₂ photocatalyst. Aqueous suspensions of the microorganisms (10⁷–10⁸ cfu ml⁻¹) and POM (or TiO₂) were irradiated with black light lamps. The POM-PCI was faster than (or comparable to) TiO₂-PCI under the experimental conditions employed in this study. The relative efficiency of POM-PCI was species-dependent. Among three POMs (H₃PW₁₂O₄₀, H₃PMo₁₂O₄₀, and H₄SiW₁₂O₄₀) tested in this study, the inactivation of E. coli was fastest with H₄SiW₁₂O₄₀ while that of B. subtilis was the most efficient with H₃PW₁₂O₄₀. Although the biocidal action of TiO₂ photocatalyst has been commonly ascribed to the role of photogenerated reactive oxygen species such as hydroxyl radicals and superoxides, the cell death mechanism with POM seems to be different from TiO₂-PCI. While TiO₂ caused the cell membrane disruption, POM did not induce the cell lysis. When methanol was added to the POM solution, not only the PCI of E. coli was enhanced (contrary to the case of TiO₂-PCI) but also the dark inactivation was observed. This was ascribed to the in situ production of formaldehyde from the oxidation of methanol. The interesting biocidal property of POM photocatalyst might be utilized as a potential disinfectant technology.     

Comparative study of the oxidation of atrazine and acetone by H2O2/UV, Fe(III)/UV, Fe(iii)/H2O2/UV and Fe(II) or Fe(III)/H2O2

In this study, the rates of degradation of organic compounds by several AOPs (H₂O₂/UV, Fe(III)/UV, Fe(III)/H₂O₂/UV, Fe(II)/H₂O₂ and Fe(III)/H₂O₂) have been compared. Experiments were carried out at pH ≈ 3 (perchloric acid / sodium perchlorate solutions) and with UV reactors equipped with a low-pressure mercury vapour lamp (emission at 253.7 run). The data obtained with atrazine ([Atrazine]_o = 100 μg/L) showed that the rate of degradation of atrazine in very dilute aqueous solution is much more rapid with Fe(III)/UV than with H₂O₂/UV. Photo-Fenton process (Fe(III)/H₂O₂/UV) was found to be more efficient than H₂O₂/UV and Fe(II)/H₂O₂ for the mineralization of acetone ([Acetone]_o = 1 mM).     

Fe and UV-enhanced ozonation of chlorophenolic compounds in aqueous medium

Mono-, di- and trichlorophenol including different isomers were degraded by O₃, O₃ + UV and O₃ + UV + Fe³⁺. Disappearance rates are nearly identical among three ozonations. Whereas TOC elimination was not completed by ozone alone. UV illumination accelerated TOC elimination rate and the addition of Fe³⁺ (O₃ + UV + Fe³⁺) further accelerated it. TOC elimination rates among different chlorophenols were in the order of mono > di > tri. The effect of Fe³⁺ was largest on the degradation of trichlorophenol. Hydroxylated aromatics, organic acids, formaldehyde and acetone were detected as intermediates.     

Optimizing electron spin resonance detection of hydroxyl radical in water

The parameters affecting the electron spin resonance (ESR) detection of hydroxyl free radical in water are studied and optimized. The hydroxyl radical is generated by the Fenton reaction with iron (II) ammonium sulfate and hydrogen peroxide reacting in a phosphate buffer using N-tert-butyl-alpha-phenylnitron as the spin trap. The concentrations of Fe²⁺, H₂O₂, and phosphate buffer are the parameters studied. The Taguchi method and the orthogonal experiment design were used to evaluate the effects of these parameters on the ESR signal intensity. By the analysis of the signal-to-noise ratio and the analysis of variance, the order of importance of the various parameters on the hydroxyl radical formation is determined for optimal ESR detection of hydroxyl radical. The results will help the development of water purification technologies using hydroxyl free radical as a green oxidant.     

不同老化条件对聚酰胺6微塑料吸附磺胺噻唑的影响

聚酰胺类微塑料(PA-MPs)和磺胺类抗生素(SAs)均为新兴污染物且已广泛检出,其中聚酰胺6微塑料由常用的聚酰胺6塑料产生,磺胺噻唑(ST)是典型的SAs.由于微塑料在环境暴露中普遍易老化,因此探究了聚酰胺6微塑料在未老化、紫外老化、紫外和H2 O2老化(分别记为PA6、PA6-UV、PA6-UV+H2 O2)下对S...     

Pulsed discharge plasma induced Fenton-like reactions for the enhancement of the degradation of 4-chlorophenol in water

To sufficiently utilize chemically active species and enhance the degradation rate and removal efficiency of toxic and biorefractory organic pollutant para-chlorophenol (para-CP), the introductions of iron metal ions (Fe²⁺/Fe³⁺) into either pulsed discharge plasma (PDP) process or the PDP process with TiO₂ photo-catalyst were tentatively performed. The experimental results showed that under the same experimental condition, the degradation rate and removal efficiency of para-CP were greatly enhanced by the introduction of iron ions (Fe²⁺/Fe³⁺) into the PDP process. Moreover, when iron ions and TiO₂ were added together in the PDP process, the degradation rate and removal energy of para-CP further improved. The possible mechanism was discussed that the obvious promoting effects were attributed to ferrous ions via plasma induced Fenton-like reactions by UV light irradiation excited and hydrogen peroxide formed in pulsed electrical discharge, resulting in a larger amount of hydroxyl radicals produced from the residual hydrogen peroxide. In addition, the regeneration of ferric ions to ferrous ions facilitates the progress of plasma induced Fenton-like reactions by photo-catalytic reduction of UV light, photo-catalytic reduction on TiO₂ surface and electron transfer of quinone intermediates, i.e. 1,4-hydroquinone and 1,4-benzoquinone.     

UV-H2O2 based AOP and its integration with biological activated carbon treatment for DBP reduction in drinking water

The presence of disinfection byproducts (DBPs) such as trihalomethanes (THMs) and haloacetic acids (HAAs) in drinking water is of great concern due to their adverse effects on human health. Emerging regulation limiting the concentration of DBPs in drinking water has increased demands for technologies and processes which reduce the formation of DBPs in drinking water. In this study, UV-H₂O₂ based advance oxidation process (AOP) was used to treat raw surface water. Experiments were conducted using low pressure mercury vapor UV lamps in collimated beam and flow-through annular photoreactors. The effect of UV fluence (0–3500 mJ cm⁻²) and hydrogen peroxide concentration (0–23 mg l⁻¹) in reducing the concentration of THMs and HAAs was examined. The UV-H₂O₂ AOP was then coupled with a downstream biological activated carbon (BAC) treatment to assess the synergetic benefits of combining the two treatments. It was observed that UV-H₂O₂ AOP was only effective at reducing DBPs at UV fluences of more than 1000 mJ cm⁻²and initial H₂O₂ concentrations of about or greater than 23 mg l⁻¹. However, the combined AOP–BAC treatment showed significant reductions of 43%, 52%, and 59% relative to untreated raw water for DBPs, TOC, and UV₂₅₄, respectively.     

Kinetics of nitromusk compounds degradation in water by ultraviolet radiation and hydrogen peroxide

The photodegradation of five representative nitromusk compounds in water has been performed in a stirred batch photoreactor with a UV low-pressure immersed mercury lamp, at constant temperature and different doses of hydrogen peroxide. The rate constants have been calculated on the basis of experimental data and a postulated first-order kinetic model. The rate constants, at 298 K and a dose of 1.1746 μmol l⁻¹ H₂O₂ ranges from 0.3567 × 10⁻³ s⁻¹ for musk tibetene, to 1.785 × 10⁻³ s⁻¹ for musk ambrette.     

Azo-dyes photocatalytic degradation in aqueous suspension of TiO2 under solar irradiation

The photodegradation of two common and very stable azo-dyes, i.e. methyl-orange (C₁₄H₁₄N₃SO₃Na) and orange II (C₁₆H₁₁N₂SO₄Na), is reported. The photocatalytic oxidation was carried out in aqueous suspensions of polycrystalline TiO₂ irradiated by sunlight. Compound parabolic collectors, installed at the “Plataforma Solar de Almería” (PSA, Spain) were used as the photoreactors and two identical reacting systems allowed to perform photoreactivity runs for the two dyes at the same time and under the same irradiation conditions. The disappearance of colour and substrates together with the abatement of total organic carbon content was monitored. The main sulfonate-containing intermediates were found to be in lower number in respect to those obtained under artificial irradiation. In particular there were no more evidence of the presence of hydroxylated transients. The dependence of dye photooxidation rate on: (i) substrate concentration; (ii) catalyst amount; and (iii) initial pH was investigated. The influence of the presence of strong oxidant species (H₂O₂, S₂O₈²⁻) and some ions (Cl⁻, SO₄²⁻) on the process was also studied.     

Degradation of aquatic humic material by ultraviolet light

Natural humic water was treated with ultraviolet (UV) light and UV + hydrogen peroxide (UV/H₂O₂. The effects on the dissolved organic carbon content (DOC), the UV-absorbance at 254 nm (UV-abs.), the molecular size distribution, pH, and mutagenic activity were monitored, and the identity and concentrations of the most abundant gas chromatographable organic degradation products were determined.

The DOC content and the UV-abs. of the water decreased substantially during treatment with UV/H₂O₂. The decreases were dependent on the time of irradiation (UV dose) as well as on the H₂O₂ dose applied. The humus macromolecules were degraded to smaller fragments during irradiation. At higher UV doses, however, part of the dissolved organic matter (DOM) was found to precipitate, probably as a result of polymerization. Oxalic acid, acetic acid, malonic acid, and n-butanoic acid were the most abundant degradation products detected. These acids were found to account for up to 20% and 80% of the DOM in UV- and UV/H₂O₂-treated waters, respectively. No mutagenic activity was generated by the UV irradiation or the UV/H₂O₂ treatment. It is further concluded that the substantial mutagenic activity formed during chlorination of humic waters cannot be decreased by using UV irradiation as a pretreatment step.     

Decomposition of chlorinated dioxins, odourous compounds and NOx from MSW incineraton plant by oxidizing catalyst

An experiment was carried out to decompose chlorinated dioxins (PCDDs, PCDFs) Chlorobenzenes, NOx and odourous compounds (H₂S, CH₄S, C₂H₆S₂, C₈H₈, C₂H₆S, C₂H₄O, NH₃) simultaneously using a catalyst in the MSW incineration plant. The experiments were conducted at temperatures from 200°C to 400°C and from 3000h⁻¹ to 6000h⁻¹ at space velocity. A catalyst containing V₂O₅ and WO₃ on the basis of TiO₂ is used, an oxidizing catalyst of the honeycomb type. The average decomposition efficiencis were 95%, 98%, 92% for PCDDs(48CDDs), PCDFs(48CDFs) and Chlorobenzenes(36CLBs) at a reaction temperature of 350°C and a space velocity of 3000h⁻¹, more than 90% for NOx at a reactiont temperature of 300°C and more than 80% for odourous compounds at the reaction temperature of 300°C and a space velocity of 6000h⁻¹. All those compounds were decomposed successfully with increasing contact time and surface. The rate-determing step was the chemical reaction of catalyst surface.     

The binding of three PCB congeners to dissolved organic carbon in freshwaters

The binding of three polychlorinated biphenyl (PCB) congeners to natural levels of dissolved organic carbon (DOC) was measured in 12 lakes and streams using Sep-Pak C₁₈ columns. The association coefficients calculated on the basis of DOC (i.e. K_DOC mL/g C), varied by over an order of magnitude among the different freshwaters and ranged between 2.05 × 10² and 8.86 × 10³ mL/g C for PCB 52 and 1.03 × 10⁴ and 1.70 × 10⁵ mL/g C for PCB 153. In general, there were no significant correlations (p > 0.05) between the K_DOC values and various chemical parameters in the study lakes and streams.

A relationship was derived between the fraction of bound PCB and the octanol-water partition coefficient. While this relationship explained almost 50% of the variation in the observed data, it is apparent that other factors influence K_DOC values and that in natural freshwaters, only a small fraction of the DOC is involved in the binding of PCBs and other hydrophobic pollutants.     

Modified Fenton reaction for trichlorophenol dechlorination by enzymatically generated H2O2 and gluconic acid chelate

Glucose oxidase is a well-known enzyme that catalyzes the oxidation of β-d-glucose to produce gluconic acid and hydrogen peroxide. Fenton reaction is a powerful oxidation technology used for the oxidation of groundwater pollutants. For the application of Fenton reaction in groundwater remediation, successful operation of Fenton reaction near neutral pH, and on-site generation of both H₂O₂ and chelate will be beneficial. The focus of this experimental study was to couple the glucose oxidation reaction with chelate-based Fenton reaction. The idea was to use the hydrogen peroxide and chelate gluconic acid generated during glucose oxidation for the dechlorination of 2,4,6-trichlorophenol (TCP) by Fenton reaction. The oxidation of glucose was achieved using the enzyme in free and immobilized forms. The rate of production of hydrogen peroxide was determined for each system, and was used to estimate the time required for complete consumption of glucose during the process, thus avoiding any traces of glucose in the Fenton reaction. In the case of free enzyme reaction, separation of the enzyme was achieved using an ultrafiltration membrane before initiating the Fenton reaction. The oxidation of TCP by Fenton reaction was performed at varying ratios of gluconic acid/Fe, and its effect on the decomposition of TCP and H₂O₂ was studied. TCP degradation was studied both in terms of parent compound degradation and free chloride generation.     

The effect of terpenes on the biodegradation of polychlorinated biphenyls by Pseudomonas stutzeri.

The effect of two terpenes, carvone and limonene, on the biodegradation of DELOR 103, a commercial mixture of polychlorinated biphenyls (PCBs), by Pseudomonas stutzeri, an isolate from long-term PCB-contaminated soil, was studied in detail. The addition of both carvone and limonene as potential inducers of the dioxygenase metabolic pathway exerted an enhancing effect on PCB biodegradation when glycerol and xylose were used as carbon sources, whereas no such effect could be determined with biphenyl and glucose as substrates. Promising biodegradation values were determined with xylose as carbon source and carvone as terpene inducer. In this system, 30-70% of the congeners were degraded in the presence of 10 mg l(-1) and 20 mg l(-1) carvone, respectively, irrespective of the used concentration, whereas only 7-37% of individual PCB congeners were eliminated from the system without terpene addition.     

Photocatalytic degradation of phenol by visible light-responsive iron-doped TiO2 and spontaneous sedimentation of the TiO2 particles

Fe-doped TiO₂ was prepared by the calcination of Fe_xTiS₂ (x = 0, 0.002, 0.005, 0.008, 0.01) and characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and UV–visible diffuse reflectance spectra. All the Fe-doped TiO₂ were composed of an anatase crystal form and showed red shifts to a longer wavelength. The activity of the Fe-doped TiO₂ for the degradation of phenol was investigated by varying the iron content during UV (365 nm) and visible light (405 nm and 436 nm) irradiation. The degradation rate depended on the Fe content and the Fe-doped TiO₂ was responsive to the visible light as well as the elevated activity toward UV light. The molar ratio of 0.005 was the optimum for both the UV and visible light irradiations. The result was discussed on the basis of the balance of the excited electron–hole trap by the doped Fe³⁺ and their charge recombination on the doped Fe³⁺ level. The Fe-doped TiO₂ (x = 0.005) was more active than P25 TiO₂ under solar light irradiation. The suspended Fe-doped TiO₂ spontaneously precipitated once the stirring of the reaction mixture was terminated.