Studies in the Biodegradation of 5 PAHs (Phenanthrene,Pyrene, Fluoranthene,Chrysene und Benzo(a)pyrene) in the Presence of Rooted Poplar Cuttings

Cuttings of Populus nigra L. cv. Loenen were cultivated in sand treated with one of the following PAHs: phenanthrene (Phen), fluoranthene (Flt), pyrene (Pyr), chrysene (Chr) and benzo[a]pyrene (BaP). The PAHs were applied at varying levels of concentration to each test series. After 6 weeks the concentration and the distribution of the PAHs in the substrate of the various sets of tests were compared with the concentration in the substrate of the control. Additionally the substrate and the plant roots were tested for evidence of degradation products of PAHs. The results revealed that the levels of concentration of Phen and Pyr detected in the substrate surrounding the roots was in some cases significantly lower than in the corresponding section of substrate in the unplanted set (= control). This phenomenon did not occur for Flt and BaP and in the case of Chr only in those substrates, which had been treated with the highest levels of concentration. As the presence of lesser amounts of Phen and Pyr in the plant pots cannot only be attributed to their accumulation and metabolism in the roots, it is fair to assume that the chemical transformation of these three PAHs took place outside the roots. The set of tests treated with Phen revealed the presence of 2- or 3-hydroxy-Phen (main components), a hydroxy-methoxy-Phen, 9,10-Phenanthrenequinone and one unidentified compound in metabolite form. Altogether eleven metabolites of Pyr were identified in the root extracts, which can be divided into three groups: 1-Hydroxy-Pyr and derivatives, dihydroxy-Pyr and derivatives and ring fission products (4-Hydroxy-Pyr and a derivative of the 4-Phen-carbonic acid). However, the metabolite mass detected for Phen and Pyr represents only an insignificant percentage in comparison with the lesser amounts of PAHs observed in the planted set of tests. This indicates that the three PAHs were reduced to lower molecular compounds, which are methodically impossible to record, and subsequently translocated to other parts of the plant and integrated into the biomass. Although no lesser amount for Flt and BaP was found in the plant pots, 1-Hydroxy-Flt, an unidentified compound of Flt and 1-Methoxy-BaP were detected. These are presumably end products which were enhanced in the roots. It was not possible to identify any transformation products of Chr. It can be assumed that the majority of metabolites were not synthesised in the roots but are a result of microbial degradation in the rhizosphere. The test plants improved the conditions for the biotransformation of Phen and Pyr significantly and accumulated Flt, Pyr, Chr and BaP in their roots. It can therefore be concluded that the use of plants in the bioremediation of contaminated soils is a promising option.     

Identification of various laccases induced by anthracene and contribution to its degradation in a Mediterranean coastal pine litter

Mediterranean coastal ecosystems are known to be highly subject to natural and anthropic environmental stress. In this study, we examine the effects of anthracene as a common pollutant on the total microbial communities from a Pinus halepensis litter of a typical Mediterranean coastal site (Les Calanques, Marseille). The main objective was to identify the microbial factors leading the resilience of this ecosystem. Two questions were addressed: (i) how lignin-degrading enzymes (Laccase, Lignin-peroxidase and Mn-peroxidase) are affected by the presence of this molecule, (ii) whether the indigenous consortia are involved in its degradation in mesocosms under favorable incubation conditions (25 °C, 60% WHC) and after different time intervals (1 and 3 month(s)). We found a strong increase in laccase production in the presence of anthracene after 3 months, together with anthracene degradation (28% ± 5). Moreover 9,10-anthraquinone is detected as the product of anthracene oxidation after 3 months. However neither lignin-peroxidase activity nor Mn-peroxidase activity is detected. Laccase proteins directly extracted from litter were sequenced via Nano-LC-MS/MS and reveal twelve different peptide sequences induced by the presence of anthracene in the mesocoms. Our study confirms the major detoxification role of this enzymatic system and highlights the high degradation potential of fungal species inhabiting P. halepensis litter, a factor in the resilience of Mediterranean ecosystems.     

A convenient test method for photochemical transformation of pollutants in the aquatic environment

A test method, based on a modified Xenotest 1200, is described, and has been proved to be convenient for determination of the rate of photolytical degradation and by that it can make a valuable contribution to the evaluation of environmental stability of organic compounds. The test method was applied to testing of photochemical degradation of organic chemicals in aquatic media. Solutions of six chlorinated phenolic substances, 8-quinolinol and 9,10-anthraquinone were illuminated with filtered light, simulating daylight at controlled conditions. Quantum yields of photochemical degradation and half lifetimes (of conversion) were calculated using a sun spectrum at 60°N. Chlorophenols absorbing light at 295 – 350 nm were converted and theoretical half lifetimes of 0.75 –2.6 hours were obtained. The photochemical conversion of 8-quinolinol was slow. Anthraquinone was studied in ethanol/water and the degradation corresponded to a half lifetime of 2.8 hours.     

Determination photostability of selected agrochemicals in water and soil.

The photolysis of selected pesticides in aqueous solutions has been investigated. The photolysis produced different intermediate substances, which were also found to be soil and microbial degradation products. The phototransformation in the presence of TiO2 and humic substances leads to a disappearance of these compounds. The reaction rate is dependent on the semiconductor oxide and concentration. Photoproducts were isolated and characterized by different spectroscopic methods. Results from this study indicate that degradation products of isoproturon are more toxic on Daphnia magna than on the parent compound.     

废水生物处理出水中溶解性微生物产物的形成机制与特征

废水生物处理出水中的溶解性微生物产物(SMP)主要产生于基质降解和微生物的内源呼吸过程,它的存在是影响生物处理出水水质和有机物去除率的一个重要因素,已引起人们的普遍关注.简单阐述了SMP的定义,详细探讨了废水生物处理出水中溶解性微生物产物的形成机制与特征.     

Transformation of PAHs during ethanol-Fenton treatment of an aged gasworks' soil

PAH-contaminated soil from a former gasworks site was treated with Fenton's reagent in a number of lab-scale slurry reactors. The degradation result obtained by traditional Fenton oxidation and Fenton oxidation preceded by ethanol treatment were compared. The ethanol pre-treatment enhanced the depletion of all PAHs in the soil by facilitating their desorption from the soil matrix. However, some PAHs, especially anthracene, benzo[a]pyrene and perylene, were more extensively depleted than other PAHs with fewer or equal numbers of fused rings, indicating that the hydroxyl radicals react faster with these PAHs than with other kinds. The ethanol present in the slurry also appeared to influence the relative reactivity of the PAHs. Furthermore, the enhanced oxidation that occurred in the ethanol pre-treated soil resulted in the accumulation of oxidation products. For example, 1-indanone, anthracene-9,10-dione, 1-methylanthracenedione, 2-methylanthracenedione, 1,8-naphthalic anhydride, benz[a]anthracene-7,12-dione and two compounds tentatively identified as hydroxy-9-fluorenones were found at higher concentrations after the treatment than before it. The accumulation was most evident for the quinones, and in many cases it could be attributed to extensive oxidation of their parent PAHs, although the total oxidation efficiency in this study was relatively poor.     

Emission of biocides from treated materials test procedures for water and air

Methods for the determination of biocide emissions from treated materials into water and air were developed and tested in order to support a comparative ecological assessment of biocidal products. Leaching tests, experiments with simulated rain, extraction cleaning of carpets and emission chamber tests were performed with a series of treated materials. The experiments focused on the effect of changes in the procedure as well as characteristics of the specimens and demonstrate the suitability of the proposed methods for biocides of different product types. It was demonstrated that emissions of biocides into water can be compared on the basis of leaching tests in which the emission kinetics of the active ingredients are recorded. However, the water volume per surface area and the timetable for water changes have to be defined in such tests. Functions of flux rates related to time can be well described for inorganic compounds, whereas modelling of the data is more complicated for organic substances. Emission chamber tests using 20-litre and 23-litre glass exsiccators, originally developed to study volatile organic compounds, were successfully adapted for the investigation of the emission of biocides from treated materials which are usually semi volatile organic compounds. However test parameters and the method of analysis have to be adapted to the substances to be determined. Generally, it was found that the emission curves for the semi volatile organic compounds investigated differ from those of volatile organic compounds.     

An oxygenated metabolite of benzo[a]pyrene increases hepatic β-oxidation of fatty acids in chick embryos

Polycyclic aromatic hydrocarbons (PAHs) are well-known carcinogens to humans and ecotoxicological effects have been shown in several studies. However, PAHs can also be oxidized into more water soluble-oxygenated metabolites (Oxy-PAHs). The first purpose of the present project was to (1) assess the effects of a mixture containing three parent PAHs: anthracene, benz[a]anthracene, and benzo[a]pyrene versus a mixture of their oxygenated metabolites, namely: anthracene-9,10-dione, benz[a]anthracene-7,12-dione, and 9,10-dihydrobenzo[a]pyrene-7-(8H)-one on the hepatic fatty acid β-oxidation in chicken embryos (Gallus gallus domesticus) exposed in ovo. The second and also main purpose of the project was to (2) assess the effects of the parent PAHs versus their oxy-PAHs analogues when injected individually, followed by (3) additional testing of the individual oxy-PAHs. The hepatic β-oxidation was measured using a tritium release assay with [9,10-³H]-palmitic acid (16:0) as substrate. The result from the first part (1) showed reduced hepatic β-oxidation after exposure in ovo to a mixture of three PAHs, however, increased after exposure to the mixture of three oxy-PAHs compared to control. The result from the second part (2) and also the follow-up experiment (3) showed that 9,10-dihydrobenzo[a]pyrene-7-(8H)-one was the causative oxy-PAH. The implication of this finding on the risk assessment of PAH metabolite exposure in avian wildlife remains to be determined. To the best of our knowledge, no similar studies have been reported.     

Aerobic biodegradability of the calcium channel antagonist verapamil and identification of a microbial dead-end transformation product studied by LC-MS/MS

In recent years pharmaceuticals and personal care products have been detected in increasing concentrations in hospital effluents, sewage treatment plants (STP) as well as in different environmental compartments such as surface water, groundwater and soil. Little is known about the elimination of these substances during sewage treatment or about the formation of potential metabolites in the environment caused by bacterial biotransformation. To assess the biodegradability of the popular cardiovascular drug verapamil and the possible formation of potential microbial degradation products, two tests from the OECD series were used in the present study: the widely used Closed Bottle test (OECD 301 D) and the modified Zahn-Wellens test (OECD 302 B). In the Closed Bottle test, a screening test that simulates the conditions of an environmental surface water compartment, no biological degradation was observed for verapamil at concentrations of 2.33mgl(-1). In the Zahn-Wellens test, a test for inherent biodegradability which allows evaluation of aerobic degradation at high bacterial density, only a partial biological degradation was found. Analysis of test samples by high performance liquid chromatography coupled to multiple stage mass spectrometry (HPLC-MSn) revealed 2-(3,4-dimethoxyphenyl)-2-isopropyl-5-(methylamino)pentane nitrile, already known as D617 (Knoll nomenclature), a metabolite of mammalian metabolism, which is the major degradation product and dead-end transformation product of aerobic degradation of verapamil.     

Anaerobic degradation of five polycyclic aromatic hydrocarbons from river sediment in Taiwan

This study investigated the anaerobic degradation of five polycyclic aromatic hydrocarbons (PAHs) from Erren River sediment in southern Taiwan. The degradation rates of PAH were in the order: acenaphthene > fluorene > phenanthrene > anthracene > pyrene. The degradation rate was enhanced when the five compounds were present simultaneously in river sediment. Comparison of the PAH degradation rates under three reducing conditions showed the following order: sulfate-reducing conditions > methanogenic conditions > nitrate-reducing conditions. The addition of electron donors (acetate, lactate and pyruvate) enhanced PAH degradation under methanogenic and sulfate-reducing conditions. However, the addition of acetate, lactate or pyruvate inhibited PAH degradation under nitrate-reducing conditions. The addition of heavy metals, nonylphenol and phthalate esters (PAEs) inhibited PAH degradation. Our results show that sulfate-reducing bacteria, methanogen and eubacteria are involved in the degradation of PAH; sulfate-reducing bacteria constitute a major microbial component in PAH degradation. Of the microorganism strains isolated from the sediment samples, we found that strain ER9 expressed the greatest biodegrading ability.     

Fate of pharmaceutical compounds and steroid hormones in soil: study of transfer and degradation in soil columns

Numerous chemical products are dispersed into the environment, and the consequences can be sometimes harmful to humans and ecosystems. Pharmaceutical compounds and hormone steroids are among these substances that concern the scientific community. Currently, little data are available on the presence and fate of these compounds in the environment and, in particular, for solid matrices. Therefore, the aim of this work was to perform soil column experiments to evaluate the accumulation, transfer and degradation of these substances in soil. The analyses were based on efficient sample preparation followed by sensitive and selective liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS). For this purpose, 23 compounds were chosen including both pharmaceutical compounds as well as steroid hormones. In addition, this experiment was performed on two soils with different properties (% clay, pH, etc.). To the best of our knowledge, no soil column experiments have been performed previously on a large number of pharmaceutical compounds and steroid hormones. Significant transfer was observed only for sulphonamides that can be justified by their polarity (log K _ow ?相似文献   

GC/MS analysis of polynuclear aromatic hydrocarbons in sediment samples from the Niger Delta region

Thirteen sediment samples from different locations in the Niger Delta region of Nigeria were analyzed for the presence of 16 polynuclear aromatic hydrocarbons (PAHs) via gas chromatography/mass spectrometry. The specific target compounds for this study included naphthalene, acenaphthylene, acenaphthene, flourene, phenanthrene, anthracene, flouranthene, pyrene, benz[a]anthracene, chrysene, benzo[b]fluoranthene, benzo[k]flouranthene, benzo[a]pyrene, benzo[ghi]perylene, dibenz[a,h]anthracene, and indeno[1,2,3-cd]pyrene. Four isotopically labeled polynuclear aromatic hydrocarbons (acanaphthene-d10, phenanthrene-d10, chrysene-d12 and perylene-d12) were used for internal standardization. All 16 PAHs were found in most of the thirteen samples with concentration ranging from 0.1 microg/kg to 28 microg/kg. It was also found that the 5 and 6-ring PAHs were present in higher concentrations than all the other compounds, indicating their high resistance to microbial degradation.     

Tracing the transformation of labelled [1-13C]phenanthrene in a soil bioreactor

[1-(13)C]-labelled phenanthrene was incubated in a closed bioreactor to study the flux and biotransformation of polycyclic aromatic hydrocarbon (PAH) in contaminated soils on a bulk and molecular level. The degradation of extractable phenanthrene was observed by GC-MS measurements and the mineralisation was monitored by (13)CO(2) production. The transformation of the (13)C-label into non-extractable soil-bound residues was determined by carbon isotopic measurements. With these data we were able to calculate a carbon budget of the (13)C-label. Moreover, the chemical structure of non-extractable bound residues was characterised by applying selective chemical degradation reactions to cleave xenobiotic subunits from the macromolecular organic soil matrix. The obtained low molecular weight products yielded (13)C-labelled compounds which were identified using IRM (isotope ratio monitoring)-GC-MS and structurally characterised with GC-MS. Most of the (13)C-labelled products obtained by chemical degradation of non-extractable bound residues are well-known metabolites of phenanthrene. Thus, metabolites of [1-(13)C]phenanthrene formed during biodegradation appear to be reactive components which are subsequently involved in the bound residue formation. Hydrolysable amino acids of the soil residues were significantly labelled with (13)C as confirmed by IRM-GC-MS measurements. Therefore, phenanthrene-derived carbon was transformed by anabolic microbial processes into typical biologically derived compounds. These substances are likely to be incorporated into humic-like material after cell death.     

Reductive hydrogenation of polycyclic aromatic hydrocarbons catalyzed by metalloporphyrins

The hydrogenation of polycyclic aromatic hydrocarbons (PAHs) (naphthalene, anthracene, and phenanthrene) catalyzed by metalloporphyrins based on cobalt, nickel or iron was studied in aqueous solutions at room temperature and ambient pressure. Nickel porphyrin (P1) activated by nanosized zero-valent iron (nano-ZVI) and cobalt porphyrins (P2) and (P4) activated by titanium(III) citrate as the electron donor were demonstrated to be promising catalysts for the reductive hydrogenation of PAHs. In particular, partially saturated di-, tetra-, and octahydrogenated products were obtained for anthracene or phenanthrene using a nickel porphyrin activated by nano-ZVI, while naphthalene was transformed to tetralin. Systems containing cobalt porphyrins activated by titanium(III) citrate exhibited a high selectivity and activity toward hydrogenation of anthracene, producing 9,10-dihydroanthracene. However, no formation of hydrogenated hydrocarbons was observed from naphthalene or phenanthrene using cobalt porphyrins.     

Toxic effect of surfactants and probable products of their biodegradation on methanogenesis in an anaerobic microbial community.

Surfactants used in household and various industries, are rather toxic; therefore, the accumulation of these compounds in the environment through wastewaters has challenged the problem of their biodegradation. In this research, an attempt was made to assess the toxic effect of various surfactants and the likely products of their biodegradation on the acetoclastic methanogens of an anaerobic microbial community. Among the substances investigated, cationic surfactants were found to be most toxic to methanogens: 154 mg/l alkamon DS and 345 mg/l catamin AB induced a 50% inhibition of methanogenesis. Toxicity studies of some aromatic and cyclic compounds, as the probable products of biodegradation of alkylbenzene sulfonate surfactants, showed that methanogenesis in the microbial community under study are rather tolerant to high concentrations of these compounds.     

The use of anthracene as a model compound in a comparative study of hydrous pyrolysis methods for industrial waste remediation

Polycyclic aromatic hydrocarbons are very stable compounds and tend to bioaccumulate in the environment due to their high degree of conjugation and aromaticity. Hydrous pyrolysis is explored as a technique for the treatment of industrial water containing PAH, using anthracene as a model compound. The reactivity of anthracene under a range of temperatures and durations are studied in this paper. Aliquots of 1.0-10.0 mg of anthracene in a range of 1.0-5.0 mL of H₂O are subjected to hydrous pyrolysis under varied conditions of temperature, reagents and duration. The conditions include oxidising systems comprising distilled water, hydrogen peroxide and Nafion-SiO₂ solid catalyst in water; and reducing systems of formic acid and formic acid/Nafion-SiO₂/Pd-C catalysts to assess a range of redox reaction conditions. Oxygen in air played a role in some of the reaction conditions. Pyrolysed products were identified and quantified by the use of Gas Chromatography-Mass Spectrometry (GC-MS). The major products were anthrone, anthraquinone, xanthone from oxidation; and multiple hydro-anthracene derivatives from reductive hydogenation. The nature of reaction conditions influenced the extent of anthracene degradation. The products formed are more reactive (less stable) as compared to anthracene the starting material and will therefore be less persistent in the environment.     

Including degradation products of persistent organic pollutants in a global multi-media box model

GOAL, SCOPE AND BACKGROUND: Global multi-media box models are used to calculate the fate of persistent organic chemicals in a global environment and assess long-range transport or arctic contamination. Currently, such models assume substances to degrade in one single step. In reality, however, intermediate degradation products are formed. If those degradation products have a high persistence, bioaccumulation potential and / or toxicity, they should be included in environmental fate models. The goal of this project was to gain an overview of the general importance of degradation products for environmental fate models, and to expand existing, exposure-based hazard indicators to take degradation products into account. METHODS: The environmental fate model CliMoChem was modified to simultaneously calculate a parent compound and several degradation products. The three established hazard indicators of persistence, spatial range and arctic contamination potential were extended to include degradation products. Five well-known pesticides were selected as example chemicals. For those substances, degradation pathways were calculated with CATABOL, and partition coefficients and half-lives were compiled from literature. RESULTS: Including degradation products yields a joint persistence value that is significantly higher than the persistence of the parent compound alone: in the case of heptachlor an increase of the persistence by a factor of 58 can be observed. For other substances, the increase is much smaller (4% for alpha-HCH). The spatial range and the arctic contamination potential (ACP) can increase significantly, too: for 2,4-D and heptachlor, an increase by a factor of 2.4 and 3.5 is seen for the spatial range. However, an important increase of the persistence does not always lead to a corresponding increase in the spatial range: the spatial range of aldrin increases by less than 50%, although the persistence increases by a factor of 20 if the degradation products are included in the assessment. Finally, the arctic contamination potential can increase by a factor of more than 100 in some cases. DISCUSSION: Influences of parent compounds and degradation products on persistence, spatial range and ACP are discussed. Joint persistence and joint ACP reflect similar characteristics of the total environmental exposure of a substance family (i.e., parent compound and all its degradation products). CONCLUSIONS: The present work emphasizes the importance of degradation products for exposure-based hazard indicators. It shows that the hazard of some substances is underestimated if the degradation products of these substances are not included in the assessment. The selected hazard indicators are useful to assess the importance of degradation products. RECOMMENDATIONS AND PERSPECTIVES: It is suggested that degradation products be included in hazard assessments to gain a more accurate insight into the environmental hazard of chemicals. The findings of this project could also be combined with information on the toxicity of degradation products. This would provide further insight into the importance of degradation products for environmental risk assessments.     

Anaerobic nonylphenol ethoxylate degradation coupled to nitrate reduction in a modified biodegradability batch test

The aim of this work was to elucidate the role of nitrate as a terminal electron acceptor on the biodegradation of NPEO. We have characterized the products of NPEO degradation by mixed microbial communities in anaerobic batch tests by means of HPLC, ¹H NMR and GC–MS. Anaerobic degradation of NPEO was strictly dependent on the presence of nitrate. Within seven days of anoxic incubation, NP2EO appeared as the major degradation product. After 21 days, NP was the main species detected, and was not degraded further even after 35 days. Nitrate concentration decreased in parallel with NPEO de-ethoxylation. A transient accumulation of nitrite was observed within the time period in which NP formation reached its maximum production. The observed generation of nonylphenol coupled to nitrate reduction suggests that the microbial consortium possessed an alternate pathway for the degradation of NPEO, which was not accessible under aerobic conditions.     

Temperature dependence of the infinite dilution activity coefficient and Henry's law constant of polycyclic aromatic hydrocarbons in water

The water solubility of 9,10-dihydroanthracene was experimentally determined between 278.12 and 313.17 K. Determinations were carried out by an experimental procedure developed in our laboratory, which is a modification of the dynamic coupled column liquid chromatographic technique. The uncertainty of the experimental determinations ranged from +/- 0.50% to +/- 3.10%. These data, as well as the water solubility data of other five polycyclic aromatic hydrocarbons (PAHs) previously studied, were used to calculate the temperature dependence of the infinite dilution activity coefficient of 9,10-dihydroanthracene, anthracene, pyrene, 9,10-dihydrophenanthrene, m-terphenyl, and guaiazulene in water. Molar excess enthalpies and entropies at infinite dilution, at 298.15 K, were also derived. The temperature dependence of the infinite dilution activity coefficients was used, together with literature values of the vapor pressures of supercooled liquid PAHs (p(B)(sc)), to estimate their Henry's law constants (HLC). Only HLC for anthracene, pyrene, and 9,10-dihydrophenanthrene were calculated, since no p(B)(sc) data were available in the literature for 9,10-dihydroanthracene, m-terphenyl, and guaiazulene. From the observed temperature dependence of the Henry's law constants the enthalpy and entropy of the phase change from the dissolved phase to the gas phase were also derived for anthracene, pyrene, and 9,10-dihydrophenanthrene.     

Microbial community responses to bioremediation treatments for the mitigation of low-dose anthracene in marine coastal sediments of Bizerte lagoon (Tunisia)

Purpose

The main goals of this study were to investigate (1) the behavior of microbial communities in response to low-dose bioavailable anthracene addition in lightly contaminated sediment from Bizerte Lagoon and (2) the effects of bioremediation treatments on microbial biomass, activity, and community structure.

Methods

Sediment microcosms amended with 1 ppm anthracene were incubated in triplicate during 30 days. Biostimulation (addition of nitrogen and phosphorus fertilizer) and bioaugmentation (inoculation of a hydrocarbonoclastic bacterium) were used as bioremediation treatments. Bacterial biomass was estimated using flow cytometry. Sediment oxygen consumption was measured with oxygen microelectrodes. Bacterial community structure was assessed by molecular fingerprints (terminal restriction fragment length polymorphism; T-RFLP) analysis.

Results

Anthracene contamination resulted in a significant reduction of bacterial abundance with an impact on cell integrity. Concomitantly, sediment oxygen consumption was strongly inhibited. Correspondence analysis on T-RFLP data indicated that bacterial community structures from anthracene-contaminated microcosms were different from that of the control. Interestingly, the changes observed in microbial biomass, structure, and activities as a result of anthracene contamination were not alleviated even with the use of biostimulation and combination of biostimulation and bioaugmentation strategy for anthracene bioremediation. Nevertheless, both treatment methods resulted in different community structures relative to the contaminated and control microcosms with the appearance of distinct populations.

Conclusion

Anthracene spiking severely affected microbial communities, suggesting dominance of nontolerant populations in this lightly-contaminated sediment. Although biostimulation and/or bioaugmentation treatments did not alleviate the anthracene toxic effects, the changes observed in microbial population and structure suggest that the proposed treatments might be promising to promote bacterial growth. Further works are still required to propose a more efficient strategy to stimulate biodegradation that takes into account the complex interactions between species for resource access.