超声-Fenton高级氧化降解染料工业废水的研究

采用超声与Fenton高级氧化技术联合处理染料废水,取得了满意的效果。同时考察了初始浓度、初始pH值、超声时间、超声频率、超声功率、H2O2和FeSO4初始浓度等因素对其COD去除效果的影响,当超声波频率为45 kHz,功率为200 W,初始pH值为2.63,超声时间为150 min,H2O2浓度为60 mmol/L,FeSO4浓度为12 mmol/L时,染料废水COD去除率达到91.8%。     

粉煤灰负载铁离子催化氧化活性黄染料废水

以粉煤灰为载体,制备铁/粉煤灰负载型催化剂,并利用该催化剂催化H2O2氧化降解活性黄染料废水,探讨了H2O2投加量、催化剂投加量、染料初始浓度和初始pH值等因素对染料废水COD去除率和脱色率的影响。结果表明,当染料废水COD初始浓度为200 mg/L,初始pH值为1.7,投加0.5 g/100 mL催化剂及加入1.0 mL浓度为1.13 mol/L的H2O2溶液时,处理效果最好,此时染料废水的COD去除率和脱色率分别达到63%和99%,并且废水的可生化性得到很大的提高。利用该负载催化剂能够有效地减少活性黄染料废水中Fe3+的残留量。     

生化法处理乳链菌肽发酵废水研究

根据乳链菌肽发酵废水氮源丰富、碳源缺乏,不利于酵母菌生长和废水处理,利用色拉油加工废水做碳源,研究了初始pH、接种量、初始C/N比、溶解氧、水力停留时间对生化法处理乳链菌肽发酵废水的影响。结果表明,最佳条件为：初始pH 4.5、溶氧浓度2～3 mg/L、接种量12%、C/N 20∶1～30∶1、水力停留时间56 h,进水COD浓度27 100 mg/L。处理后的乳链菌肽发酵废水COD去除率达91.3%、出水pH 6.0～8.0。     

O3氧化工艺处理黄连素制药废水研究

采用臭氧（O3）氧化法处理含高浓度黄连素和COD的制药废水,探讨了废水初始pH、O3投加量及初始黄连素浓度等因素对O3氧化过程的影响,确定了O3氧化技术处理黄连素制药废水的最佳操作条件。结果表明,O3能够有效分解废水中的黄连素,降低其COD浓度;黄连素浓度为700mg／L、COD为3500mg／L、pH为0．88的废水,进气O3浓度为14．05mg／（L·min）,处理时间为180rain（即投加量为2529mg／L）时,黄连素和COD的降解率分别可达77．46％和41．28％,BOD,／COD比（B／C比）从0．06提高到0．34,增加了4．7倍;随着废水中初始黄连素浓度的升高,废水COD降解率逐渐降低。O3氧化法是一种有效的黄连素制药废水预处理技术,可以大大提高废水的可生化性。     

O3氧化工艺处理黄连素制药废水研究

采用臭氧(O₃)氧化法处理含高浓度黄连素和COD的制药废水,探讨了废水初始pH、O₃投加量及初始黄连素浓度等因素对O₃氧化过程的影响,确定了O₃氧化技术处理黄连素制药废水的最佳操作条件。结果表明,O₃能够有效分解废水中的黄连素,降低其COD浓度;黄连素浓度为700 mg/L、COD为3 500 mg/L、pH为0.88的废水,进气O₃浓度为14.05 mg/（L?min）,处理时间为180 min（即投加量为2 529 mg/L）时,黄连素和COD的降解率分别可达77.46%和41.28%,BOD₅/COD比（B/C比）从0.06提高到0.34,增加了4.7倍;随着废水中初始黄连素浓度的升高,废水COD降解率逐渐降低。O₃氧化法是一种有效的黄连素制药废水预处理技术,可以大大提高废水的可生化性。     

UV/Fenton法处理间-甲酚废水

利用UV/Fenton工艺对模拟间-甲苯酚废水进行了处理,研究了H2O2加入量、FeSO4加入量、pH、原水初始COD值、环境温度、反应时间等因素对COD去除率的影响.实验表明:间-甲苯酚浓度为100mg/L、初始COD值251 mg/L的废水,在30℃下,pH为4.Q,[H2O2]/[Fe2 ]=15(质量浓度比),紫外灯照射3 h后,COD去除率达86.3%,若再经Ca(OH)2絮凝沉降,则COD去除率提高到92.6%.同时,对Fenton及UV/Fenton的处理效果进行了比较,实验表明:UV/Fenton的处理效果明显优于Fenton法.     

UV/Fenton法处理间-甲酚废水

利用UV/Fenton工艺对模拟间-甲苯酚废水进行了处理,研究了H2O2加入量、FeSO4加入量、pH、原水初始COD值、环境温度、反应时间等因素对COD去除率的影响.实验表明：间-甲苯酚浓度为100mg/L、初始COD值251 mg/L的废水,在30℃下,pH为4.Q,[H2O2]/[Fe^2＋]=15（质量浓度比）,紫外灯照射3 h后,COD去除率达86.3%,若再经Ca（OH）2絮凝沉降,则COD去除率提高到92.6%.同时,对Fenton及UV/Fenton的处理效果进行了比较,实验表明：UV/Fenton的处理效果明显优于Fenton法.     

响应面法优化Fenton预处理干法腈纶废水

采用Fenton法预处理难降解干法腈纶废水,选取H2O2用量、Fe2+用量、初始pH和反应温度4个因素为变量,COD去除率为响应值进行中心组合设计。利用响应面法对实验结果进行分析,建立了以COD去除率为响应值的二次多项式模型并进行了显著性检验,分析了各因素单独及交互作用对COD去除率的影响,确定了最佳反应条件,并考察了最佳条件下处理前后废水可生化性和毒性变化。结果表明,所选取的4个因素影响COD去除率的主次顺序依次为:H2O2用量、Fe2+用量、初始pH和反应温度;在H2O2浓度为90.0 mmol/L、Fe2+浓度为23.9 mmol/L、初始pH值为3.4、温度为38.5℃的最佳条件下,COD去除率为53.8%,与模型预测值51.9%吻合度较高,偏差仅为3.66%;最佳条件下处理后废水可生化性显著提高,生物毒性明显降低,适宜于后续的生化处理。     

活性炭-微波辐照处理丁腈胶乳生产废水的研究

以活性炭-微波辐照工艺处理丁腈胶乳生产废水,考察了催化剂的种类及用量、废水初始浓度、废水初始pH值、微波辐照时间和微波功率等对废水COD去除率的影响.结果表明,采用3 g粉末活性炭处理100 mL COD浓度为3500 mg/L左右的丁腈胶乳废水,在微波辐照功率为200 W,辐照时间4 min的条件下,废水COD去除率最高可达96.6%.动力学研究表明,在最佳操作条件下的反应表观过程近似符合一级反应规律,动力学方程为In(C0/C)=0.6034t 0.9247(R=0.9926),反应速率常数k=0.6034 min-1,半衰期t1/2=1.15 min.     

改性碳纤维阴极电Fenton法处理电镀废水中的有机物

采用改性碳纤维(ACF)阴极电Fenton法处理电镀废水中的有机物,研究pH、Fe2+浓度、电流密度和曝气量对电镀废水COD去除率的影响。结果表明,改性ACF电Fenton法对电镀废水COD去除效果明显,在最佳反应条件(pH为3.0,Fe2+初始摩尔浓度为2.0mmol/L,电流密度为3.0mA/cm2,曝气量为0.9L/min)下反应90min,COD去除率为90.7%。     

Chloroaromatic pollutants in mussels incubated in two finnish watercourses polluted by industry

Concentrations of different chlorinated compounds were measured in mussels incubated in two polluted watercourses, a river (the River Kymijoki) and a lake (Lake Vanaja) for four weeks in summer 1995. The sum concentrations of polychlorinated phenols (PCP) and biphenyls (PCB) were both about 1 μg/g lipid weight (lw) in Lake Vanaja mussels, while in the River Kymijoki mussels PCPs were non-detectable and PCBs were measured 120 ng/g lIw. The concentrations of toxic polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners ranged between <17 and 370 pg/g Iw in Lake Vanaja mussels and between <38 and 11,000 pg/g lw in the River Kymijoki mussels. Polychlorinated diphenyl ethers (PCDE) were detected in the mussels incubated in the River Kymijoki (0.4–1.1 ng/g Iw), but not in those incubated in Lake Vanaja. Polychlorinated phenoxyanisoles (PCPA) were measured 33 ng/g lw and polychlorinated phenoxyphenols (PCPP) 300 ng/g lw in the mussels incubated in the River Kymijoki. PCPAs were also detected in reference samples, which were sediment and pike from the River Kymijoki and Baltic salmon, seal and white-tailed sea eagle.     

Book review

The Pesticide Manual ‐ A World Compendium, 8th Edition, C.R. Worthing, Editor and S.B. Walker, Assistant Editor, British Crop Protection Council, BCPC Publications Sales, Bear Farm, Binfield, Bracknell, Berkshire RG12 5QE, England. 1987, 1100 pp., UK £50; Overseas £56. ISBN 0–948404–01–9.     

Organochlorine compounds in a three-step terrestrial food chain

The concentrations of 15 organochlorine chemicals (PCBs and pesticides) were studied in a Central European oak wood food chain system: Great tit (Parus major), caterpillars (Tortrix viridana, Operophtera brumata, Erannis defoliaria), and oak-leaves (Quercus robur). Juvenile tits receive organochlorines from the mother via egg transfer and, eventually to a greater extent, from the caterpillar food source during nestling period. The concentrations of PCB 153 (2,2′,4,4′,5,5′-hexachlorobiphenyl, the most abundant in this study) was found in leaf material at ca. 1 ng/g, in caterpillars 10 ng/g, and in bird eggs 170 ng/g on an average and on a dry mass basis.     

The chemical stability of formulations of some hydrolyzable insecticides in aqueous mixtures with hydrolysis catalysts

Abstract

The active ingredients in commercial formulations of malathion, oxamyl, carbaryl, diazinon, and chlorpyrifos diluted to “spray tank”; concentrations with buffered distilled or natural water of pH 4–9 were stable for at least 24 hr. Formulations of trichlorfon were not stable at pH 7 or above but disappearance rates were slower than for the pure chemical in homogeneous solution. Cupric ion was observed to be an effective catalyst for the hydrolysis of a variety of pure organophosphorus insecticides but did not catalyze hydrolysis of the active ingredients of the formulations examined. Increasing the dilution of the formulation increased the susceptibility of malathion, oxamyl, and carbaryl to hydrolysis.     

Radionuclides in pinon pine (Pinus edulis) nuts from los alamos national laboratory lands and the dose from consumption

Abstract

One of the dominant tree species growing within and around the eastern portion of Los Alamos National Laboratory (LANL), Los Alamos, NM, lands is the pinon pine (Pinus edulis). Pinon pine is used for firewood, fence posts, and building materials and is a source of nuts for food—the seeds are consumed by a wide variety of animals and are also gathered by people in the area and eaten raw or roasted. This study investigated the (1) concentration of ³H, ¹³⁷Cs, ⁹⁰Sr, ^totU, ²³⁸Pu, ^{239, 240}Pu, and²⁴¹ Am in soils (0‐ to 12‐in. [31 cm] depth underneath the tree), pinon pine shoots (PPS), and pinon pine nuts (PPN) collected from LANL lands and regional background (BG) locations, (2) committed effective dose equivalent (CEDE) from the ingestion of nuts, and (3) soil to PPS to PPN concentration ratios (CRs). Most radionuclides, with the exception of ³H in soils, were not significantly higher (p < 0.10) in soils, PPS, and PPN collected from LANL as compared to BG locations, and concentrations of most radionuclides in PPN from LANL have decreased over time. The maximum net CEDE (the CEDE plus two sigma minus BG) at the most conservative ingestion rate (10 lb [4.5 kg]) was 0.0018 mrem (0.018 μSv); this is far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem (1000 μSv). Soil‐to‐nut CRs for most radionuclides were within the range of default values in the literature for common fruits and vegetables.     

Degradation and sorption of imidacloprid in dissimilar surface and subsurface soils

Degradation and sorption/desorption are important processes affecting the leaching of pesticides through soil. This research characterized the degradation and sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine) in Drummer (silty clay loam) and Exeter (sandy loam) surface soils and their corresponding subsurface soils using sequential extraction methods over 400 days. By the end of the incubation, approximately 55% of imidacloprid applied at a rate of 1.0 mg kg^?1 degraded in the Exeter sandy loam surface and subsurface soils, compared to 40% of applied imidacloprid within 300 days in Drummer surface and subsurface soils. At the 0.1 mg kg^?1 application rate, dissipation was slower for all four soils. Water-extractable imidacloprid in Exeter surface soil decreased from 98% of applied at day 1 to > 70% of the imidacloprid remaining after 400 d, as compared to 55% in the Drummer surface soil at day 1 and 12% at day 400. These data suggest that imidacloprid was bioavailable to degrading soil microorganisms and sorption/desorption was not the limiting factor for biodegradation. In subsurface soils > 40% of ¹⁴C-benzoic acid was mineralized over 21 days, demonstrating an active microbial community. In contrast, cumulative ¹⁴CO₂ was less than 1.5% of applied ¹⁴C-imidacloprid in all soils over 400 d. Qualitative differences in the microbial communities appear to limit the degradation of imidacloprid in the subsurface soils.     

Biochemical interaction of six op delayed neurotoxicants with several neurotargets

Abstract

Five organophosphorous insecticides: Leptophos, EPN, Cyano‐fenphos, trichloronate and salithion proved to cause irreversible ataxia not only to chicken but also to mice and sheep. TOCP was included as a reference. Cyanofenphos blocked the catecholamine B‐receptor binding activity with ³H‐norepinephrine at a level similar to that of the specific inhibitor propranolol in the mouse heart preparation. In the lamb heart preparation, the B‐receptor was more sensitive to Leptophos, salithion and TOCP than to propranolol. The six compounds and their oxons were screened for their in‐vitro inhibition to monamine oxidase (MAO), acetyl cholinesterase (AChE) and neurotoxic esterase (NTE) in the brain of either mouse, lamb or chicken. It is believed that their AChE inhibition stands for their acute toxicity, while NTE inhibition is responsible for their paralytic ataxia.     

土壤中砷的化学平衡

本文比较详细地综述了砷的化学特性,环境背景值及来源和循环,土壤中砷的三大化学平衡即沉淀溶解平衡,氧化还原平衡,吸附解吸平衡,以及微生物对砷的转化。     

Elemental uptake by edible herbs and lettuce (Latuca sativa)

The total concentration of toxic elements (aluminum, cadmium, chromium and lead) and selected macro and micro elements (iron, manganese, copper and zinc) are reported in six leafy edible vegetation species, namely lettuce, spinach, cabbage, chards and green and red types of Amaranth herbs. Although spinach and chards had greater than 125 mv of iron, both the amaranthus herbs recorded > than 320 μ g g^{? 1} dry weight. In both the spinach and chard species, the Mn and Zn levels were appreciable recording > 225 μ g g^{? 1} and 150 μ g g^{? 1} dry weight, respectively. Aluminum concentrations were (in μ g g^{? 1} dry weight) lettuce (10), cabbage (11), spinach (167), chards (65), amaranthus green (293) and amaranthus red (233). All the micro and macro elements and the toxic elements (Ni, Cr, Cd and Pb) elements analyzed, were below the recommended maximum permitted levels (RMI) in vegetables. Further the elemental uptake and distribution of the nine elements, at three growth stages of the lettuce plant grown on soil bed under controlled conditions are detailed. In the soil, except for iron (16%), greater than 33% of the other cations were in exchangeable form. Generally in the lettuce plant, roots retained much of the iron (> 224 μ g g^{? 1}) and aluminum (> 360 μ g g^{? 1}), while leaves had less than 200 μ g g^{? 1} of iron and 165 μ g g^{? 1} of Al. Although the concentrations of elements marginally decreased with growth, the lettuce leaves had significant amounts of Mn (30 μ g g^{? 1}), Zn (50 μ g g^{? 1}) and Cu (3.6 μ g g^{? 1}). Some presence of lead in leaves (2.0 μ g g^{? 1}) was noticed, but all the toxic and other elements analyzed were well below the RMI values for the vegetables.     

The dissipation of nonlyphenol in stream and pond water under simulated field conditions

Abstract

The dissipation of 1.0 ppm nonylphenol in stream and pond water, incubated in flasks at 16°C under simulated field conditions up to 44 days indicated that the half‐life was 2.5 days if the flasks were open, and 16 days if they were closed. A transformed product was detected in the closed flasks.

Translocation of nonylphenol in water occurred when treated water samples were incubated in the presence of sediment. After 10 days, nonylphenol was detected only in the sediment, but not in water (detection limit = 10 ppb). About 80% of the nonylphenol was degraded in 71 days, but no degradation occurred if the water and the sediment were autoclaved prior to incubation.