Characterization of activated carbons prepared from sugarcane bagasse by ZnCl2 activation.

Activated carbons were prepared from the agricultural waste of sugarcane bagasse by the chemical activation with zinc chloride (ZnCl2) at the activation temperature of 500 degrees C with soaking time of 0.5 hour. The influence of activation parameters on the final carbon products was examined by varying the impregnation ratio (i.e., mass ratio of added ZnCl2 to bagasse) and bagasse size. The physical properties of carbon products were characterized by nitrogen adsorption/desorption isotherms (at 77 K) and helium displacement method. The surface area and pore volume of carbons were thus obtained by the BET equation and t-plot method. Also, the particle density and porosity of carbons were estimated by the total pore volume and true density. The increases of the values of surface area and pore volume are approximately proportional to the impregnation ratio. The microporous carbon product with the BET surface area of 905 m2/g and total pore volume of 0.44 cm3/g was obtained in the present study. Further, the adsorption isotherms of two acid dyes from aqueous solutions onto the carbon products were performed at 30 degrees C. The results show that the adsorption isotherms of acid dyes with high molecular weight or large molecular size on the microporous adsorbents of activated carbons are plateau forms, indicating multilayer adsorptions, which may be attributed to the steric hindrance of the adsorbate molecules.     

Roles of physical and chemical properties of activated carbon in the adsorption of lead ions

Elucidation of the roles of chemical and physical properties of activated carbons is an important basis for the systematic development of adsorbents with optimal properties specific for certain applications. Such an understanding has challenged most researchers and this has been attributed with the difficulty in decoupling the effect of chemical and physical properties that characterize activated carbons. This study proposed empirical modeling in resolving the effects of individual carbon properties in lead adsorption. A model based on lead adsorption and carbon properties including total surface area, mean pore size and heteroatom concentrations has been shown to adequately describe the lead adsorption onto activated carbons prepared from bagasse. To support this investigation a series of activated carbons were prepared from bagasse by physical and by chemical activation techniques. The surface chemical properties of the carbons were inferred from carbon pH and heteroatom concentrations. The physical characterizations of the carbons included total surface area by the BET technique and mean pore size measured using the Horvath-Kawazoe equation. Adsorption tests were conducted using a low concentration of lead (5 ppm) and the solution pH was maintained at 1.0 to maintain lead speciation to the un-complexed Pb(2+) ion. The adequacy of the proposed empirical models was statistically assessed. This form of analysis was shown to provide valuable information in tailor making adsorbents and selecting appropriate adsorbents for lead adsorption.     

Adsorption of acid dye onto activated carbons prepared from agricultural waste bagasse by ZnCl2 activation

A series of activated carbons were prepared from agricultural waste sugarcane bagasse by chemical activation with zinc chloride (ZnCl2) as an activating agent at 500 degrees C and 0.5 h soaking time. The Langmuir surface area and total pore volume were used to estimate the average pore diameter of the carbon products. The values of the surface area and pore volume increased linearly with increase in the impregnation ratio (IR) up to 100 wt%. The adsorption capacities of the derived adsorbents for Acid Orange 10 were measured at 20 degrees C and 40 degrees C to gain further insights into the acidic surface oxides of the adsorbent from the results of Fourier transform infrared (FTIR) spectroscopy analysis and pH measurement. Adsorption isotherms of the acid dye on adsorbents prepared were determined and correlated with common isotherm equations. It was found that the Langmuir model appears to fit the isotherm data better than the Freundlich model. The physical properties of these adsorbents were consistent with the parameters obtained from the isotherm equations.     

A comparative study of anaerobically digested and undigested sewage sludges in preparation of activated carbons.

Disposal of sewage sludge is an increasingly expensive and environmentally sensitive problem throughout the world. Preparation of activated carbon from sewage sludge offers an attractive re-use alternative to the traditional disposal routes. The objective of this research work was to compare anaerobically digested sewage sludge (DS) and undigested sewage sludge (US) as source materials in the preparation of activated carbons. Prior to the preparation the properties of the two types of sewage sludges were determined and compared. Subsequently the sludge samples were activated with 5 M ZnCl2 solution and thereafter pyrolysed at heating temperature of 650 degrees C for 2 h with the heating rate of 15 degrees C/min under a nitrogen atmosphere. The produced activated carbons were characterised by surface area and porosity analysis, CHN elemental composition and ash contents determination, and aqueous phase phenol adsorption tests. The results indicate that in comparison with the DS, the US had a higher carbon content and lower ash content, and accordingly yielded a better activated carbon with a higher BET surface area, pore volume, carbon content and phenol adsorption capacity.     

磷酸微波活化多孔生物质炭对亚甲基蓝的吸附特性

以甘蔗渣为原料,采用微波辅助H3PO4活化法制备富含含氧酸官能团的中孔生物质炭。通过扫描电子显微镜SEM、傅立叶变换红外光谱FT-IR等技术对生物质炭物理化学性质进行表征,并通过静态实验法,探讨炭样对亚甲基蓝的吸附行为及热力学性质。结果表明,H3PO4活化制备蔗渣生物质炭的适宜条件为浸渍比1：1,烘干时间10h,活化功率900W,活化时间22min,在此条件下制得的生物质炭得率为39．2％,碘值为817mg／g,亚甲基蓝值为229mg／g,为国家一级品标准的1．7倍。红外光谱分析表明,炭样表面以羟基、羰基、羧基等酸性官能团为主。静态吸附实验表明,Freundlich方程与Redlich—Peterson方程能较好地描述等温吸附行为,表现为优惠吸附。热力学研究表明,吸附吉布斯自由能（△G0）〈0,说明吸附反应是自发过程,而吸附标准焓变（△H0）〉70KJ／mol,表明亚甲基蓝在制备炭样上的吸附是吸热反应,升温有利于吸附,且化学反应在吸附过程中发挥了重要作用。     

Production of activated carbons from pyrolysis of waste tires impregnated with potassium hydroxide

Activated carbons were produced from waste tires using a chemical activation method. The carbon production process consisted of potassium hydroxide (KOH) impregnation followed by pyrolysis in N2 at 600-900 degrees C for 0-2 hr. The activation method can produce carbons with a surface area (SA) and total pore volume as high as 470 m2/g and 0.57 cm3/g, respectively. The influence of different parameters during chemical activation, such as pyrolysis temperature, holding time, and KOH/tire ratio, on the carbon yield and the surface characteristics was explored, and the optimum preparation conditions were recommended. The pore volume of the resulting carbons generally increases with the extent of carbon gasified by KOH and its derivatives, whereas the SA increases with degree of gasification to reach a maximum value, and then decreases upon further gasification.     

Production of sugarcane bagasse-based activated carbon for formaldehyde gas removal from potted plants exposure chamber

Agricultural wastes such as rice straw, sugar beet, and sugarcane bagasse have become a critical environmental issue due to growing agriculture demand. This study aimed to investigate the valorization possibility of sugarcane bagasse waste for activated carbon preparation. It also aimed to fully characterize the prepared activated carbon (BET surface area) via scanning electron microscope (SEM) and in terms of surface functional groups to give a basic understanding of its structure and to study the adsorption capacity of the sugarcane bagasse-based activated carbon using aqueous methylene blue (MB). The second main objective was to evaluate the performance of sugarcane bagasse-based activated carbon for indoor volatile organic compounds removal using the formaldehyde gas (HCHO) as reference model in two potted plants chambers. The first chamber was labeled the polluted chamber (containing formaldehyde gas without activated carbon) and the second was taken as the treated chamber (containing formaldehyde gas with activated carbon). The results indicated that the sugarcane bagasse-based activated carbon has a moderate BET surface area (557 m²/g) with total mesoporous volume and microporous volume of 0.310 and 0.273 cm³/g, respectively. The prepared activated carbon had remarkable adsorption capacity for MB. Formaldehyde removal rate was then found to be more than 67% in the treated chamber with the sugarcane bagasse-based activated carbon. The plants’ responses for this application as dry weight, chlorophyll contents, and protein concentration were also investigated.

Implications: Preparation of activated carbon from sugarcane bagasse (SCBAC) is a promising approach to produce cheap and efficient adsorbent for gas pollutants removal. It may be also a solution for the agricultural wastes problems in big cities, particularly in Egypt. MB adsorption tests suggest that the SCBAC have high adsorption capacity. Formaldehyde gas removal in the plant chambers indicates that the SCBAC have potential to recover volatile gases. The results confirmed that the activated carbon produced from sugarcane bagasse waste raw materials can be used as an applicable adsorbent for treating a variety of gas pollutants from the indoor environment.     

Removal of congo red from aqueous solution by bagasse fly ash and activated carbon: kinetic study and equilibrium isotherm analyses

Present investigation deals with the utilisation of bagasse fly ash (BFA) (generated as a waste material from bagasse fired boilers) and the use of activated carbons-commercial grade (ACC) and laboratory grade (ACL), as adsorbents for the removal of congo red (CR) from aqueous solutions. Batch studies were conducted to evaluate the adsorption capacity of BFA, ACC and ACL and the effects of initial pH (pH(0)), contact time and initial dye concentration on adsorption. The pH(0) of the dye solution strongly affected the chemistry of both the dye molecules and BFA in an aqueous solution. The effective pH(0) was 7.0 for adsorption on BFA. Kinetic studies showed that the adsorption of CR on all the adsorbents was a gradual process. Equilibrium reached in about 4h contact time. Optimum BFA, ACC and ACL dosages were found to be 1, 20 and 2 g l(-1), respectively. CR uptake by the adsorbents followed pseudo-second-order kinetics. Equilibrium isotherms for the adsorption of CR on BFA, ACC and ACL were analysed by the Freundlich, Langmuir, Redlich-Peterson, and Temkin isotherm equations. Error analysis showed that the R-P isotherm best-fits the CR adsorption isotherm data on all adsorbents. The Freundlich isotherm also shows comparable fit. Thermodynamics showed that the adsorption of CR on BFA was most favourable in comparison to activated carbons.     

污泥活性炭对次甲基蓝废水的吸附

立足于污泥的资源化,利用化学活化法制得的污泥基活性炭,处理次甲基蓝染料废水.考察了污泥活性炭的粒径以及染料废水的pH值对染料脱色效果以及活性炭的吸附量的影响,并对吸附过程进行等温吸附线和吸附动力学分析.结果表明,在本研究的范围内,污泥活性炭的粒径越小、染料废水的pH值越高,则污泥活性炭对染料废水的吸附效果越好.当粒径在200目以上时,去除率及吸附量分别为88.2％和136.7 mg/g;当pH值为11时,去除率和吸附量分别为90.4％和91.9 mg/g.污泥活性炭对次甲基蓝染料的吸附脱除符合Langmuir吸附等温线和Lagergren准二级动力学方程.     

Preparation of activated carbons from raw and biotreated agricultural residues for removal of volatile organic compounds

Activated carbons with diverse physical and chemical properties were produced from four agriculture residues, including raw barley husk, biotreated barley husk, rice husk, and pistachio shell. Results showed that with adequate steam activation (30-90 min, 50% H2O(g),/50% N2), activated carbons with surface areas between 360 and 950 m2 g(-1) were developed. Further increases in the activation time destroyed the pore structure of activated carbons, which resulted in a decrease in the surface area and pore volume. Biotreated agricultural residues were found to be suitable precursors for producing mesoporous activated carbons. The oxygen content of activated carbons increased with increasing activation time. Results from X-ray photoelectron spectroscopy examination further suggested that H2O molecules react with the carbon surface, enhancing the deconvoluted peak area of carbonyl and carboxyl groups. Equilibrium adsorption of toluene indicated that the adsorption capacities increased with an increase in the inlet toluene concentration and a decrease in temperature. The adsorption isotherms were successfully fitted with Freundlich, Langmuir, and Dubinin-Radushkevich equations. Activated carbons derived from agricultural residues appear to be more applicable to adsorb volatile organic compounds at a low concentration and high-temperature environment.     

Properties of pyrolytic chars and activated carbons derived from pilot-scale pyrolysis of used tires

Used tires were pyrolyzed in a pilot-scale quasi-inert rotary kiln. Influences of variables, such as time, temperature, and agent flow, on the activation of obtained char were subsequently investigated in a laboratory-scale fixed bed. Mesoporous pores are found to be dominant in the pore structures of raw char. Brunauer-Emmett-Teller (BET) surfaces of activated chars increased linearly with carbon burnoff. The carbon burnoff of tire char achieved by carbon dioxide (CO2) under otherwise identical conditions was on average 75% of that achieved by steam, but their BET surfaces are almost the same. The proper activation greatly improved the aqueous adsorption of raw char, especially for small molecular adsorbates, for example, phenol from 6 to 51 mg/g. With increasing burnoff, phenol adsorption exhibited a first-stage linear increase followed by a rapid drop after 30% burnoff. Similarly, iodine adsorption first increased linearly, but it held as the burnoff exceeded 40%, which implied that the reduction of iodine adsorption due to decreasing micropores was partially made up by increasing mesopores. Both raw chars and activated chars showed appreciable adsorption capacity of methylene-blue comparable with that of commercial carbons. Thus, tire-derived activated carbons can be used as an excellent mesoporous adsorbent for larger molecular species.     

Adsorption of mercury by activated carbon prepared from dried sewage sludge in simulated flue gas

Conversion of sewage sludge to activated carbon is attractive as an alternative method to ocean dumping for the disposal of sewage sludge. Injection of activated carbon upstream of particulate matter control devices has been suggested as a method to remove elemental mercury from flue gas. Activated carbon was prepared using various activation temperatures and times and was tested for their mercury adsorption efficiency using lab-scale systems. To understand the effect of the physical property of the activated carbon, its mercury adsorption efficiency was investigated as a function of its Brunauer–Emmett–Teller (BET) surface area. Two simulated flue gas conditions, (1) without hydrogen chloride (HCl) and (2) with 20 ppm HCl, were used to investigate the effect of flue gas composition on the mercury adsorption capacity of activated carbon. Despite very low BET surface area of the prepared sewage sludge activated carbons, their mercury adsorption efficiencies were comparable under both simulated flue gas conditions to those of pinewood and coal activated carbons. After injecting HCl into the simulated flue gas, all sewage sludge activated carbons demonstrated high adsorption efficiencies, that is, more than 87%, regardless of their BET surface area.

Implications: We tested activated carbons prepared from dried sewage sludge to investigate the effect of their physical properties on their mercury adsorption efficiency. Using two simulated flue gas conditions, we conducted mercury speciation for the outlet gas. We found that the sewage sludge activated carbon had mercury adsorption efficiency comparable to pinewood and coal activated carbons, and the presence of HCl minimized the effect of physical property of the activated carbon on its mercury adsorption efficiency.     

高温载硫活性炭的制备及脱汞能力研究

研究了载硫温度、硫炭比(简称S/C),吸附温度等因素对载硫活性炭的硫含量、脱汞能力以及硫损失的影响,探讨载硫活性炭制备的工艺条件优化。结果表明,不同载硫温度下制备的载硫活性炭的气态Hg0吸附能力远强于原料活性炭;载硫温度不同时,负载到活性炭孔隙或表面上的硫的形态不同,导致了脱汞能力的差异,较合适的载硫温度为350℃;S/C为5%(质量分数,下同)时,随着吸附温度的升高,载硫活性炭的气态Hg0吸附量降低;在一定的载硫温度下,原料中S/C越高时,制备的载硫活性炭的硫含量越高、气态Hg0吸附能力越强,但其硫损失率也越高,从实际的使用效果来看,较合适的S/C为10%。     

TiO2/活性炭复合纳米纤维膜对亚甲基蓝的吸附研究

摘要以自制的TiO2/活性炭复合纳米纤维膜作为吸附剂,以亚甲基蓝为目标污染物,研究了亚甲基蓝初始浓度、温度、TiO2/活性炭复合纳米纤维膜投加量、pH等对TiO2/活性炭复合纳米纤维膜吸附去除亚甲基蓝的影响,并研究了TiO2/活性炭复合纳米纤维膜的Zeta电位、接触角、光催化再生性能.结果表明:(1)静态吸附时,随着亚...     

Properties of Pyrolytic Chars and Activated Carbons Derived from Pilot-Scale Pyrolysis of Used Tires

Abstract

Used tires were pyrolyzed in a pilot-scale quasi-inert rotary kiln. Influences of variables, such as time, temperature, and agent flow, on the activation of obtained char were subsequently investigated in a laboratory-scale fixed bed. Meso-porous pores are found to be dominant in the pore structures of raw char. Brunauer-Emmett-Teller (BET) surfaces of activated chars increased linearly with carbon burnoff. The carbon burnoff of tire char achieved by carbon dioxide (CO₂) under otherwise identical conditions was on average 75% of that achieved by steam, but their BET surfaces are almost the same. The proper activation greatly improved the aqueous adsorption of raw char, especially for small molecular adsorbates, for example, phenol from 6 to 51 mg/g. With increasing burnoff, phenol adsorption exhibited a first-stage linear increase followed by a rapid drop after 30% burnoff. Similarly, iodine adsorption first increased linearly, but it held as the burnoff exceeded 40%, which implied that the reduction of iodine adsorption due to decreasing micro-pores was partially made up by increasing mesopores. Both raw chars and activated chars showed appreciable adsorption capacity of methylene-blue comparable with that of commercial carbons. Thus, tire-derived activated carbons can be used as an excellent mesoporous adsorbent for larger molecular species.     

Low-cost adsorbents from bio-waste for the removal of dyes from aqueous solution

Activated carbons (ACs) were developed from bio-waste materials like rice husk and peanut shell (PS) by various physicochemical activation methods. PS char digested in nitric acid followed by treatment at 673 K resulted in high surface area up to ～585 m²/g. The novelty of the present study is the identification of oxygen functional groups formed on the surface of activated carbons by infrared and X-ray photoelectron spectroscopy and quantification by using temperature programmed decomposition (TPD). Typical TPD data indicated that each activation method may lead to varying amounts of acidic and basic functional groups on the surface of the adsorbent, which may be a crucial factor in determining the adsorption capacity. It was shown that ACs developed during the present study are good adsorbents, especially for the removal of a model textile dye methylene blue (MB) from aqueous solution. As MB is a basic dye, H₂O₂-treated rice husk showed the best adsorption capacity, which is in agreement with the acidic groups present on the surface. Removal of the dye followed Langmuir isotherm model, whereas MB adsorption on ACs followed pseudo-second-order kinetics.     

Enhanced mercuric chloride adsorption onto sulfur-modified activated carbons derived from waste tires

A number of activated carbons derived from waste tires were further impregnated by gaseous elemental sulfur at temperatures of 400 and 650 degrees C, with a carbon and sulfur mass ratio of 1:3. The capabilities of sulfur diffusing into the micropores of the activated carbons were significantly different between 400 and 650 degrees C, resulting in obvious dissimilarities in the sulfur content of the activated carbons. The sulfur-impregnated activated carbons were examined for the adsorptive capacity of gas-phase mercuric chloride (HgC1) by thermogravimetric analysis (TGA). The analytical precision of TGA was up to 10(-6) g at the inlet HgCl2 concentrations of 100, 300, and 500 microg/m3, for an adsorption time of 3 hr and an adsorption temperature of 150 degrees C, simulating the flue gas emitted from municipal solid waste (MSW) incinerators. Experimental results showed that sulfur modification can slightly reduce the specific surface area of activated carbons. High-surface-area activated carbons after sulfur modification had abundant mesopores and micropores, whereas low-surface-area activated carbons had abundant macropores and mesopores. Sulfur molecules were evenly distributed on the surface of the inner pores after sulfur modification, and the sulfur content of the activated carbons increased from 2-2.5% to 5-11%. After sulfur modification, the adsorptive capacity of HgCl2 for high-surface-area sulfurized activated carbons reached 1.557 mg/g (22 times higher than the virgin activated carbons). The injection of activated carbons was followed by fabric filtration, which is commonly used to remove HgCl2 from MSW incinerators. The residence time of activated carbons collected in the fabric filter is commonly about 1 hr, but the time required to achieve equilibrium is less than 10 min. Consequently, it is worthwhile to compare the adsorption rates of HgCl2 in the time intervals of < 10 and 10-60 min.     

Adsorption of Cu2+ and methyl orange from aqueous solutions by activated carbons of corncob-derived char wastes

Corncob-derived char wastes (CCW) obtained from biomass conversion to syngas production through corncob steam gasification, which were often discarded, were utilized for preparation of activated carbon by calcination, and KOH and HNO₃ activation treatments, on the view of environment protection and waste recycling. Their adsorption performance in the removal of heavy metal ions and dye molecules from wastewater was evaluated by using Cu²⁺ and methyl orange (MO) as the model pollutant. The surface and structure characteristics of the CCW-based activated carbons (CACs) were investigated by N₂ adsorption, CO₂ adsorption, FT-IR, and He-TPD. The adsorption capacity varied with the activation methods of CACs and different initial solution concentrations, indicating that the adsorption behavior was influenced by not only the surface area and porosity but also the oxygen functional groups on the surface of the CACs. The equilibrium adsorption data were analyzed with the Langmuir, Freundlich, and Temkin isotherm models, and the adsorption kinetics was evaluated by the pseudo-first-order and pseudo-second-order models.     

孔结构和表面化学性质对活性炭吸附性能的影响

测定了室温下3种活性炭(GAC-C、GAC-P和GAC-T)对CO2、CH4和N2的吸附性能,并对颗粒活性炭孔结构和表面化学性质进行了表征,探讨了孔结构和表面化学性质对活性炭吸附性能的影响。结果表明:由于吸附机理、孔结构、表面含氧官能团和分子极性的差异,CO2、CH4和N2在活性炭上的饱和吸附量和吸附常数的关系为CO2>CH4>N2;CH4和N2的饱和吸附量主要受活性炭微孔孔容的影响,N2和CO2饱和吸附量的差异分别是由0.572～2.0 nm的微孔和0.4～6 nm的孔引起的;CH4吸附常数主要受较大中孔和大孔影响,N2吸附常数与微孔密切相关,大孔对CO2的吸附常数影响最大。     

Kinetic, equilibrium isotherm and thermodynamic studies of Cr(VI) adsorption onto low-cost adsorbent developed from peanut shell activated with phosphoric acid

A particular agricultural waste, peanut shell, has been used as precursor for activated carbon production by chemical activation with H₃PO₄. Unoxidized activated carbon was prepared in nitrogen atmosphere which was then heated in air at a desired temperature to get oxidized activated carbon. The prepared carbons were characterized for surface area, surface morphology, and pore volume and utilized for the removal of Cr(VI) from aqueous solution. Batch mode experiments were conducted to study the effects of pH, contact time, particle size, adsorbent dose, initial concentration of adsorbate, and temperature on the adsorption of Cr(VI). Cr(VI) adsorption was significantly dependent on solution pH, and the optimum adsorption was observed at pH 2. Pseudo-first-order, pseudo-second-order, and intraparticle diffusion models were used to analyze the kinetic data obtained at different initial Cr(VI) concentrations. The adsorption kinetic data were described very well by the pseudo-second-order model. Equilibrium isotherm data were analyzed by the Langmuir, Freundlich, and Temkin models. The results showed that the Langmuir adsorption isotherm model fitted the data better in the temperature range studied. The adsorption capacity which was found to increase with temperature showed the endothermic nature of Cr(VI) adsorption. The thermodynamic parameters, such as Gibb’s Free energy change (ΔG°), standard enthalpy change (ΔH°), and standard entropy change (ΔS°) were evaluated.