Careers in Air Pollution Control Plant Pathology

ABSTRACT

Profiles of the sources of nonmethane organic compounds (NMOCs) were developed for emissions from vehicles, petroleum fuels (gasoline, liquefied petroleum gas [LPG], and natural gas), a petroleum refinery, a smelter, and a cast iron factory in Cairo, Egypt. More than 100 hydrocarbons and oxygenated hydrocarbons were tentatively identified and quantified. Gasoline-vapor and whole-gasoline profiles could be distinguished from the other profiles by high concentrations of the C₅ and C₆ saturated hydrocarbons. The vehicle emission profile was similar to the whole-gasoline profile, with the exception of the unsaturated and aromatic hydrocarbons, which were present at higher concentrations in the vehicle emission profile. High levels of the C₂-C₄ saturated hydrocarbons, particularly n-butane, were characteristic features of the petroleum refinery emissions. The smelter and cast iron factory emissions were similar to the refinery emissions; however, the levels of benzene and toluene were greater in the former two sources. The LPG and natural gas emissions contained high concentrations of n-butane and ethane, respectively. The NMOC source profiles for Cairo were distinctly different from profiles for U.S. sources, indicating that NMOC source profiles are sensitive to the particular composition of petroleum fuels that are used in a location.     

Particulate matter speciation profiles for light-duty gasoline vehicles in the United States

Representative profiles for particulate matter particles less than or equal to 2.5 µm (PM_2.5) are developed from the Kansas City Light-Duty Vehicle Emissions Study for use in the U.S. Environmental Protection Agency (EPA) vehicle emission model, the Motor Vehicle Emission Simulator (MOVES), and for inclusion in the EPA SPECIATE database for speciation profiles. The profiles are compatible with the inputs of current photochemical air quality models, including the Community Multiscale Air Quality Aerosol Module Version 6 (AE6). The composition of light-duty gasoline PM_2.5 emissions differs significantly between cold start and hot stabilized running emissions, and between older and newer vehicles, reflecting both impacts of aging/deterioration and changes in vehicle technology. Fleet-average PM_2.5 profiles are estimated for cold start and hot stabilized running emission processes. Fleet-average profiles are calculated to include emissions from deteriorated high-emitting vehicles that are expected to continue to contribute disproportionately to the fleet-wide PM_2.5 emissions into the future. The profiles are calculated using a weighted average of the PM_2.5 composition according to the contribution of PM_2.5 emissions from each class of vehicles in the on-road gasoline fleet in the Kansas City Metropolitan Statistical Area. The paper introduces methods to exclude insignificant measurements, correct for organic carbon positive artifact, and control for contamination from the testing infrastructure in developing speciation profiles. The uncertainty of the PM_2.5 species fraction in each profile is quantified using sampling survey analysis methods. The primary use of the profiles is to develop PM_2.5 emissions inventories for the United States, but the profiles may also be used in source apportionment, atmospheric modeling, and exposure assessment, and as a basis for light-duty gasoline emission profiles for countries with limited data.

Implications: PM_2.5 speciation profiles were developed from a large sample of light-duty gasoline vehicles tested in the Kansas City area. Separate PM_2.5 profiles represent cold start and hot stabilized running emission processes to distinguish important differences in chemical composition. Statistical analysis was used to construct profiles that represent PM_2.5 emissions from the U.S. vehicle fleet based on vehicles tested from the 2005 calendar year Kansas City metropolitan area. The profiles have been incorporated into the EPA MOVES emissions model, as well as the EPA SPECIATE database, to improve emission inventories and provide the PM_2.5 chemical characterization needed by CMAQv5.0 for atmospheric chemistry modeling.     

Speciated non-methane organic compounds emissions from food cooking in Mexico

Non-methane organic compound (NMOC) emissions from different sorts of food preparation sites, were quantified for the first time in Mexico, in order to develop emission profiles for further application in the chemical mass balance receptor model (CMB). Restaurants using charcoal grills and LP gas stoves, “tortillerı́as”, food frying places and rotisseries were sampled using SUMMA^® stainless-steel canisters to analyse NMOC by high-resolution gas chromatography. The results obtained show that profiles determined from food cooking processes have similarities to those found in LP gas combustion, which is the most common fuel in Mexico used for this purpose, although there were differences in the relative composition of propane and butane in both cases. This suggests that, the rates of combustion of propane and butane are different. It has also been detected that propene, a reactive olefin is produced during the combustion process. The obtained profiles of restaurants, rotisseries and fried food show an important contribution of two carbon compounds (ethane, ethylene and acetylene) that can be attributed to the complex process of grease and meat cooking. The presence of these compounds cannot be attributed to vehicular sources since the concentrations are higher than in ambient air. These were also determined from aromatic compounds such as benzene, toluene and xylene in the combustion of vegetal charcoal. The measured concentrations indicate that NMOC emissions from cooking may become an important indoor source of NMOC under crowded conditions in closed places.     

Development of Instrumentation for Continuous On-line Monitoring of Non-Methane Organic Carbon in Air Emissions

ABSTRACT

Non-methane organic carbon (NMOC) is a measure of total organic carbon in an air emission, excluding that from methane. Thus, it measures the total amount of carbon, irrespective of the structure and functional groups in the molecule. The U.S. Environmental Protection Agency (EPA) Method 25 is used for quantification of NMOC in emission sources and in ambient air. This method involves laboratory analysis of collected air samples and cannot be used for real-time measurements. It is prone to interferences from CO₂, CH₄, and CO, as well as moisture. In this paper, a novel method for continuous, on-line monitoring of NMOC in air emissions and ambient air is presented. Detection limits are at ppb levels, and interference of permanent gases have been eliminated.     

Summer and winter nonmethane hydrocarbon emissions from on-road motor vehicles in the Midwestern United States

On-road vehicle emission rates of nonmethane hydrocarbons (NMHCs) were measured in two tunnels in Milwaukee, WI, in summer 2000 and winter 2001. Seasonal ambient temperatures in the Midwestern United States vary more widely than in locations where most studies of NMHC emissions from vehicle fleets have been conducted. Ethanol is the added fuel oxygenate in the area, and, thus, emissions measured here are of interest as other regions phase out methyl tertiary butyl ether and increase the use of ethanol. Total emissions of NMHCs in three types of tunnel tests averaged 4560 +/- 800 mg L(-1) fuel burned (average +/- standard error). To investigate the impact of cold start on vehicle emissions, samples were collected as vehicles exited a parking structure in subzero temperatures. NMHC emissions in the subzero cold-start test were 8830 +/- 190 mg L(-1) fuel-nearly double the tunnel emissions. Comparison of ambient data for the Milwaukee area with tunnel emissions showed the impact of seasonal differences in fuels and emissions on the urban atmosphere. Composition of fuel samples collected from area gas stations in both seasons was correlated with vehicle emissions; the predominant difference was increased winter emissions of lighter hydrocarbons present in winter gasoline. A chemical mass balance model was used to determine the contributions of whole gasoline and gasoline headspace vapors to vehicle emissions in the tunnel and cold-start tests, which were found to vary with season. Results of the mass balance model also indicate that partially combusted components of gasoline are a major contributor to emissions of aromatic compounds and air toxic compounds, including benzene, toluene, xylenes, napthalene, and 1,3-butadiene, whereas air toxics hexane and 2,2,4-trimethylpentane are largely attributed to gasoline and headspace vapors.     

A Characterization of Emissions from an Early Model Flexible-Fuel Vehicle

An emission study was conducted on a 1987 Ford Crown Victoria flexible-fuel vehicle, an early prototype which had been driven about 25,000 miles. The vehicle was run on both gasoline and a blend of 85 percent methanol and 15 percent gasoline. Emission rates of regulated pollutants (hydrocarbons, carbon monoxide, nitrogen oxides, formaldehyde, and methanol) and nonregulated pollutants (speciated organic materials) were determined for both exhaust and evaporative emissions. Tests were run varying the driving cycle, ambient temperature and catalytic converter. In general, hydrocarbon composition of exhaust emissions was significantly affected by catalyst replacement and cold starts, slightly affected by driving schedule, and unaffected by ambient temperature and test fuel. Hydrocarbon composition of evaporative emissions was only sensitive to the type of evaporative test being performed: diurnal tests typically had larger fractions of lower molecular weight paraffins than hot soak tests.     

NMOC,ozone, and organic aerosol in the southeastern United States, 1999–2007: 1. Spatial and temporal variations of NMOC concentrations and composition in Atlanta,Georgia

Volatile organic compounds (VOCs) are emitted from anthropogenic and natural (biogenic) sources into the atmosphere. Characterizing their ambient mixing ratios or concentrations is a challenge because VOCs comprise hundreds of species, and accurate measurements are difficult. Long-term hourly and daily-resolution data have been collected in the metropolitan area of Atlanta, Georgia, a major city dominated by motor vehicle emissions. A series of observations of daily, speciated C₂–C₁₀ non-methane organic compounds (NMOC) and oxygenated hydrocarbons (OVOC) in mid-town Atlanta (Jefferson Street, JST) are compared with data from three urban-suburban sites and a nearby non-urban site. Annual-average mixing ratios of NMOC and OVOC at JST declined from 1999 through 2007. Downward trends in NMOC, CO, and NO_y corroborate expected emission changes as reflected in emission inventories for Atlanta’s Fulton County. Comparison of the JST NMOC composition with data from roadside and tunnel sampling reveals similarities to motor vehicle dominated samples. The JST annual average VOC-OH reactivities from 1999 to 2007 were relatively constant compared with the decline in annual-average NMOC mixing ratios. Mean reactivity at JST, in terms of concentration*k_OH, was approximately 40% alkenes, 22% aromatics, 16% isoprene and 6% other biogenics, 13% C₇–C₁₀ alkanes and 3% C₂-C₆ alkanes, indicating that biogenic NMOCs are important but not dominant contributors to the urban reactive NMOC mix. In contrast, isoprene constituted ～50% of the VOC-OH reactivities at two non-urban sites. Ratios of 24-hour average CO/benzene, CO/isopentane, and CO/acetylene concentrations indicate that such species are relatively conserved, consistent with their low reactivity. Ratios of more-reactive to less-reactive species show diurnal variability largely consistent with expected emission patterns, transport and mixing of air, and chemical processing.     

Sensitivity of Source Apportionment of Urban Particulate Matter to Uncertainty in Motor Vehicle Emissions Profiles

Abstract

A sensitivity analysis was conducted to characterize sources of uncertainty in results of a molecular marker source apportionment model of ambient particulate matter using mobile source emissions profiles obtained as part of the Gasoline/Diesel PM Split Study. A chemical mass balance (CMB) model was used to determine source contributions to samples of fine particulate matter (PM_2.5) collected over 3 weeks at two sites in the Los Angeles area in July 2001. The ambient samples were composited for organic compound analysis by the day of the week to investigate weekly trends in source contributions. The sensitivity analysis specifically examined the impact of the uncertainty in mobile source emissions profiles on the CMB model results. The key parameter impacting model sensitivity was the source profile for gasoline smoker vehicles. High-emitting gasoline smoker vehicles with visible plumes were seen to be a significant source of PM in the area, but use of different measured profiles for smoker vehicles in the model gave very different results for apportionment of gasoline, diesel, and smoker vehicle tailpipe emissions. In addition, the contributions of gasoline and diesel emissions to total ambient PM varied as a function of the site and the day of the week.     

An examination of the 6:00 a.m.-9:00 a.m. measurements of ozone precursors in the New York City metropolitan area

In recent years, ambient measurements of hourly ozone precursor concentrations, namely speciated and total nonmethane organic compounds (NMOCs), have become available through the Photochemical Assessment Monitoring Stations (PAMS) program. Prior to this, NMOCs were measured in the central business district using a canister to obtain the 3-hr integrated sample for the 6:00 a.m.-9:00 a.m. period. Such sampling had been carried out annually for nearly a decade at three locations in the New York City metropolitan area. The intent of these measurements, along with measurements of the other ozone precursor, NO(x), was to provide an understanding of ozone formation and the emissions loading and mix in the urban area. The analysis of NMOC and NO(x) measurements shows a downward trend in the case of NMOC. In addition, we compared the canister-based NMOC concentrations with data obtained from the PAMS program for the 6:00 a.m.-9:00 a.m. period. Analysis of the NMOC concentrations reveals poor spatial correlation between the various monitors, reflecting the effect of localized emissions. This suggests that NMOC measurements made at a single location cannot be viewed as representative of the entire region. On the other hand, correlations were found to be higher among the NO(x) monitors, indicating the commonality of emission     

Comparison of the MOVES2010a,MOBILE6.2, and EMFAC2007 mobile source emission models with on-road traffic tunnel and remote sensing measurements

The Desert Research Institute conducted an on-road mobile source emission study at a traffic tunnel in Van Nuys, California, in August 2010 to measure fleet-averaged, fuel-based emission factors. The study also included remote sensing device (RSD) measurements by the University of Denver of 13,000 vehicles near the tunnel. The tunnel and RSD fleet-averaged emission factors were compared in blind fashion with the corresponding modeled factors calculated by ENVIRON International Corporation using U.S. Environmental Protection Agency's (EPA's) MOVES2010a (Motor Vehicle Emissions Simulator) and MOBILE6.2 mobile source emission models, and California Air Resources Board's (CARB's) EMFAC2007 (EMission FACtors) emission model. With some exceptions, the fleet-averaged tunnel, RSD, and modeled carbon monoxide (CO) and oxide of nitrogen (NO_x) emission factors were in reasonable agreement (±25%). The nonmethane hydrocarbon (NMHC) emission factors (specifically the running evaporative emissions) predicted by MOVES were insensitive to ambient temperature as compared with the tunnel measurements and the MOBILE- and EMFAC-predicted emission factors, resulting in underestimation of the measured NMHC/NO_x ratios at higher ambient temperatures. Although predicted NMHC/NO_x ratios are in good agreement with the measured ratios during cooler sampling periods, the measured NMHC/NO_x ratios are 3.1, 1.7, and 1.4 times higher than those predicted by the MOVES, MOBILE, and EMFAC models, respectively, during high-temperature periods. Although the MOVES NO_x emission factors were generally higher than the measured factors, most differences were not significant considering the variations in the modeled factors using alternative vehicle operating cycles to represent the driving conditions in the tunnel. The three models predicted large differences in NO_x and particle emissions and in the relative contributions of diesel and gasoline vehicles to total NO_x and particulate carbon (TC) emissions in the tunnel.

Implications: Although advances have been made to mobile source emission models over the past two decades, the evidence that mobile source emissions of carbon monoxide and hydrocarbons in urban areas were underestimated by as much as a factor of 2–3 in past inventories underscores the need for on-going verification of emission inventories. Results suggest that there is an overall increase in motor vehicle NMHC emissions on hot days that is not fully accounted for by the emission models. Hot temperatures and concomitant higher ratios of NMHC emissions relative to NO_x both contribute to more rapid and efficient formation of ozone. Also, the ability of EPA's MOVES model to simulate varying vehicle operating modes places increased importance on the choice of operating modes to evaluate project-level emissions.     

Real-world and type-approval emission evolution of passenger cars

The investigation of several passenger car generations with gasoline engines shows that the emissions depend very strongly on the driving cycle. Official type approval cycles allow just very inaccurate predications about their real-world emissions. The measured gasoline vehicles have up to factor 11 higher real-life emissions than in type approval cycles. However, a clear reduction of real-world emissions can be seen over the different investigated generations of gasoline cars. In addition, it can be seen that the cold start emissions depend strongly on ambient temperature levels for all generations of cars and that the cold start accounts for an increasing part of the total pollutant emissions. As an extreme example, the cold start hydrocarbon emissions of Euro-3 cars at –20°C ambient temperature correspond approximately to those of 1,000 km driving with warm engines.     

Sensitivity of source apportionment of urban particulate matter to uncertainty in motor vehicle emissions profiles

A sensitivity analysis was conducted to characterize sources of uncertainty in results of a molecular marker source apportionment model of ambient particulate matter using mobile source emissions profiles obtained as part of the Gasoline/Diesel PM Split Study. A chemical mass balance (CMB) model was used to determine source contributions to samples of fine particulate matter (PM2.5) collected over 3 weeks at two sites in the Los Angeles area in July 2001. The ambient samples were composited for organic compound analysis by the day of the week to investigate weekly trends in source contributions. The sensitivity analysis specifically examined the impact of the uncertainty in mobile source emissions profiles on the CMB model results. The key parameter impacting model sensitivity was the source profile for gasoline smoker vehicles. High-emitting gasoline smoker vehicles with visible plumes were seen to be a significant source of PM in the area, but use of different measured profiles for smoker vehicles in the model gave very different results for apportionment of gasoline, diesel, and smoker vehicle tailpipe emissions. In addition, the contributions of gasoline and diesel emissions to total ambient PM varied as a function of the site and the day of the week.     

Receptor Model Evaluation of the Southeast Michigan Ozone Study Ambient NMOC Measurements

Abstract

Large-scale studies like the Southeast Michigan Ozone Study (SEMOS) have focused attention on quantifying and spedating inventories for volatile organic compounds (VOCs). One approach for evaluating the accuracy of a VOC emission inventory is the development of a chemical mass balance (CMB) receptor model for ambient non-methane organic compound (NMOC) measurements. CMB evaluations of ambient hydrocarbon data provide a sample-specific allocation of emissions to individual source categories. This study summarizes the results of an application of the CMB model to the NMOC data from the SEMOS study. Comparison of CMB results with emission inventory values for the Detroit area show that vehicle emissions are well represented by the inventory, as are architectural coatings and coke ovens. Estimated emissions from petroleum refineries and graphic arts industries are much lower in the inventory than determined from the receptor allocation. Under-reporting of fugitive VOC emissions from petroleum refineries is an ongoing problem. Emissions from graphic arts industries are underestimated in the inventory partly because of the broad characterization of the emission factor (i.e., mass emitted/capita), which may be less useful when specific locations and days are under consideration. This study also demonstrates the effectiveness of the CMB approach when used prospectively to track the implementation of emission control strategies. While vehicle emission concentrations were unchanged from 1988 to 1993, measurement-based CMB results suggest a decrease in evaporative emissions during this time period resulting from Reid vapor pressure (RVP) reductions (from 11.0 psi in 1988 to 8.6 psi in 1993) and fleet turnover. Changes in emissions from coke plants and petroleum refineries were also seen in the CMB allocations for these sources.     

On-road measurement of fine particle and nitrogen oxide emissions from light- and heavy-duty motor vehicles

An updated assessment of fine particle emissions from light- and heavy-duty vehicles is needed due to recent changes to the composition of gasoline and diesel fuel, more stringent emission standards applying to new vehicles sold in the 1990s, and the adoption of a new ambient air quality standard for fine particulate matter (PM_2.5) in the United States. This paper reports the measurement of emissions from vehicles in a northern California roadway tunnel during summer 1997. Separate measurements were made of uphill traffic in two tunnel bores: one bore carried both light-duty vehicles and heavy-duty diesel trucks, and the second bore was reserved for light-duty vehicles. Ninety-eight percent of the light-duty vehicles were gasoline-powered. In the tunnel, heavy-duty diesel trucks emitted 24, 37, and 21 times more fine particle, black carbon, and sulfate mass per unit mass of fuel burned than light-duty vehicles. Heavy-duty diesel trucks also emitted 15–20 times the number of particles per unit mass of fuel burned compared to light-duty vehicles. Fine particle emissions from both vehicle classes were composed mostly of carbon; diesel-derived particulate matter contained more black carbon (51±11% of PM_2.5 mass) than did light-duty fine particle emissions (33±4%). Sulfate comprised only 2% of total fine particle emissions for both vehicle classes. Sulfate emissions measured in this study for heavy-duty diesel trucks are significantly lower than values reported in earlier studies conducted before the introduction of low-sulfur diesel fuel. This study suggests that heavy-duty diesel vehicles in California are responsible for nearly half of oxides of nitrogen emissions and greater than three-quarters of exhaust fine particle emissions from on-road motor vehicles.     

The benzene problem: impact of three-way catalyst technology: potential for further improvement

Chemical ionisation mass spectrometry (CI-MS) was applied to study the benzene emission characteristics of a TWC-vehicle at a time resolution of one Hertz. Three important operating conditions with increased emissions were identified: at vehicle start; at extended stop-and-go situations; and whenever a catalyst-induced benzene formation occurs. The cold start influence was detectable for about 200 seconds of driving corresponding to a distance of 1.2 km. At hot engine/catalyst mean pre- and post-catalyst emission rates of 25–150 mg km^-1 and 0.1–135 mg km^-1 were determined. Catalyst conversion varied from 0.07 to >0.99. Even negative conversion efficiencies were observed at several occasions, indicating that benzene can be formed de novo in a TWC. It is of importance to lower benzene emissions at these critical operating conditions to further reduce ambient air levels in cities and with it the cancer risk for large proportions of our population.     

Temperature effects on particulate emissions from DPF-equipped diesel trucks operating on conventional and biodiesel fuels

Emissions tests were conducted on two medium heavy-duty diesel trucks equipped with a particulate filter (DPF), with one vehicle using a NOx absorber and the other a selective catalytic reduction (SCR) system for control of nitrogen oxides (NOx). Both vehicles were tested with two different fuels (ultra-low-sulfur diesel [ULSD] and biodiesel [B20]) and ambient temperatures (70ºF and 20ºF), while the truck with the NOx absorber was also operated at two loads (a heavy weight and a light weight). The test procedure included three driving cycles, a cold start with low transients (CSLT), the federal heavy-duty urban dynamometer driving schedule (UDDS), and a warm start with low transients (WSLT). Particulate matter (PM) emissions were measured second-by-second using an Aethalometer for black carbon (BC) concentrations and an engine exhaust particle sizer (EEPS) for particle count measurements between 5.6 and 560 nm. The DPF/NOx absorber vehicle experienced increased BC and particle number concentrations during cold starts under cold ambient conditions, with concentrations two to three times higher than under warm starts at higher ambient temperatures. The average particle count for the UDDS showed an opposite trend, with an approximately 27% decrease when ambient temperatures decreased from 70ºF to 20ºF. This vehicle experienced decreased emissions when going from ULSD to B20. The DPF/SCR vehicle tested had much lower emissions, with many of the BC and particle number measurements below detectable limits. However, both vehicles did experience elevated emissions caused by DPF regeneration. All regeneration events occurred during the UDDS cycle. Slight increases in emissions were measured during the WSLT cycles after the regeneration. However, the day after a regeneration occurred, both vehicles showed significant increases in particle number and BC for the CSLT drive cycle, with increases from 93 to 1380% for PM number emissions compared with tests following a day with no regeneration.

Implications:?The use of diesel particulate filters (DPFs) on trucks is becoming more common throughout the world. Understanding how DPFs affect air pollution emissions under varying operating conditions will be critical in implementing effective air quality standards. This study evaluated particulate matter (PM) and black carbon (BC) emissions with two DPF-equipped heavy-duty diesel trucks operating on conventional fuel and a biodiesel fuel blend at varying ambient temperatures, loads, and drive cycles.     

Nonmethane Organic Compound to Nitrogen Oxide Ratios and Organic Composition in Cities and Rural Areas

The observed ranges in nonmethane organic compound (NMOC) concentrations, NMOC composition and nitrogen oxides (NO_X) concentrations have been evaluated for urban and nonurban areas at ground level and aloft of the contiguous United States. The ranges in NMOC to NO_X ratios also are considered. The NMOC composition consistently shifts towards less reactive compounds, especially the alkanes, in air parcels over nonurban areas compared to the NMOC composition near ground level within urban areas. The values for the NMOC to NO_X ratios, 1.2 to 4.2, in air aloft over nonurban areas are lower than in air at ground level urban sites, ≥8, and much lower than in air at ground level nonurban sites, ≥20.

The layers of air aloft over a number of nonurban areas of the United States tend to accumulate NO_X emissions from the tall stacks of large fossil fuel power plants located at nonurban sites. During the night into the morning hours, the air aloft is isolated from any fresh NMOC emissions predominately coming from near surface sources. Conversely, during this extended period of restricted vertical mixing, air near the surface accumulates NMOC emissions while this air is isolated from the major NO_X sources emitting aloft. These differences in the distribution of NMOC and NO_X sources appear to account for the much larger NMOC to NO_X ratios reported near ground level compared to aloft over nonurban areas.

Two types of experimental results are consistent with these conclusions: (1) observed increases in surface rural NO_X concentrations during the morning hours during which the mixing depth increases to reach the altitude at which NO_X from the stacks of fossil fuel power plants is being transported downwind; (2) high correlations of total nitrate at rural locations with Se, which is a tracer for coal-fired power plant NO_X emissions.

The implications of these conclusions from the standpoint of air quality strategies are suggested by use of appropriate scenarios applied to both urban and regional scale photochemical air quality models. The predictions from urban model scenarios with NMOC to NO_X ratios up to 20 are that NO_X control will result in the need for the control of more NMOC emissions than necessary in the absence of NO_X control, in order to meet the O₃ standard. On a regional scale, control of NO_X emissions from fossil fuel power plants has little overall effect regionally but does result on a more local scale in both small decreases and increases in O₃ concentrations compared to the baseline scenario without NO_X control. The regional modeling results obtained to date suggest that NO_X control may be effective in reducing O₃ concentrations only for a very limited set of conditions in rural areas.     

Fine particulate matter emissions inventories: comparisons of emissions estimates with observations from recent field programs

Emissions inventories of fine particulate matter (PM2.5) were compared with estimates of emissions based on data emerging from U.S. Environment Protection Agency Particulate Matter Supersites and other field programs. Six source categories for PM2.5 emissions were reviewed: on-road mobile sources, nonroad mobile sources, cooking, biomass combustion, fugitive dust, and stationary sources. Ammonia emissions from all of the source categories were also examined. Regional emissions inventories of PM in the exhaust from on-road and nonroad sources were generally consistent with ambient observations, though uncertainties in some emission factors were twice as large as the emission factors. In contrast, emissions inventories of road dust were up to an order of magnitude larger than ambient observations, and estimated brake wear and tire dust emissions were half as large as ambient observations in urban areas. Although comprehensive nationwide emissions inventories of PM2.5 from cooking sources and biomass burning are not yet available, observational data in urban areas suggest that cooking sources account for approximately 5-20% of total primary emissions (excluding dust), and biomass burning sources are highly dependent on region. Finally, relatively few observational data were available to assess the accuracy of emission estimates for stationary sources. Overall, the uncertainties in primary emissions for PM2.s are substantial. Similar uncertainties exist for ammonia emissions. Because of these uncertainties, the design of PM2.5 control strategies should be based on inventories that have been refined by a combination of bottom-up and top-down methods.     

Fine Particulate Matter Emissions Inventories: Comparisons of Emissions Estimates with Observations from Recent Field Programs

Abstract

Emissions inventories of fine particulate matter (PM_2.5) were compared with estimates of emissions based on data emerging from U.S. Environment Protection Agency Particulate Matter Supersites and other field programs. Six source categories for PM_2.5 emissions were reviewed: on-road mobile sources, nonroad mobile sources, cooking, biomass combustion, fugitive dust, and stationary sources. Ammonia emissions from all of the source categories were also examined. Regional emissions inventories of PM in the exhaust from on-road and nonroad sources were generally consistent with ambient observations, though uncertainties in some emission factors were twice as large as the emission factors. In contrast, emissions inventories of road dust were up to an order of magnitude larger than ambient observations, and estimated brake wear and tire dust emissions were half as large as ambient observations in urban areas. Although comprehensive nationwide emissions inventories of PM_2.5 from cooking sources and biomass burning are not yet available, observational data in urban areas suggest that cooking sources account for approximately 5–20% of total primary emissions (excluding dust), and biomass burning sources are highly dependent on region. Finally, relatively few observational data were available to assess the accuracy of emission estimates for stationary sources. Overall, the uncertainties in primary emissions for PM_2.5 are substantial. Similar uncertainties exist for ammonia emissions. Because of these uncertainties, the design of PM_2.5 control strategies should be based on inventories that have been refined by a combination of bottom-up and top-down methods.     

Quantification of highway vehicle emissions hot spots based upon on-board measurements

The purpose of this study is to demonstrate a methodology for quantification of high emissions hot spots along roadways based upon real-world, on-road vehicle emissions measurements. An emissions hot spot is defined as a fixed location along a corridor in which the peak emissions are statistically significantly greater by more than a factor of 2 than the average emissions for free-flow or near free-flow conditions on the corridor. A portable instrument was used to measure on-road tailpipe emissions of carbon monoxide, nitric oxide, hydrocarbons, and carbon dioxide on a second-by-second basis during actual driving. Measurements were made for seven vehicles deployed on two primary arterial corridors. The ratio of average emissions at hot spots to the average emissions observed during a trip was as high as 25 for carbon monoxide, 5 for nitric oxide, and 3 for hydrocarbons. The relationships between hot spots and explanatory variables were investigated using graphical and statistical methods. Average speed, average acceleration, standard deviation of speed, percent of time spent in cruise mode, minimum speed, maximum acceleration, and maximum power have statistically significant associations with vehicle emissions and influence emissions hot spots. For example, stop-and-go traffic conditions that result in sudden changes in speed, and traffic patterns with high accelerations, are shown to generate hot spots. The implications of this work for future model development and applications to environmental management are discussed.