城市干污泥热解气化

针对包头市南郊污水处理厂污水污泥,采用先热解后对热解残渣进行气化的方法探讨城市污泥的有效利用方式。污泥热解实验取升温速率（20~60℃·min-1）和终温（400~600℃）作为影响因素,得出各热解产物产率的变化规律。结果表明,污泥热解在终温为600℃时失重率达到57.53%,焦油产率在450℃达到峰值。污泥残渣的气化分别以水蒸气和CO2作为气化剂,探讨了800~1 000℃范围内的气化产品气组分变化规律。以水蒸气为气化剂时,污泥热解残渣的可制备富氢产品气,产品气中H2体积分数随着反应温度的增加而增加,1 000℃时H2含量可达68.83%,H2+CO含量达到81.36%,低位热值为9.18 MJ·Nm-3。以CO2作为气化剂时,产品气中富含CO,温度越高CO含量越高,1 000℃时到达最大值53.84%,产品气低位热值为7.25 MJ·Nm-3。     

Community Odours in the Vicinity of a Petrochemical Industrial Complex

Community odours in the vicinity of an oil refinery and petrochemical industrial area were studied by an observer network throughout an entire year. Odour episodes occurred during 0.86 percent of the time of the study. Odour reports increased closer to the refinery. Within a range of 12.5 km, more than 50 percent of the odours were estimated to originate from the refinery. The most typical odour was that of reduced sulphur compounds (35.2 percent of all observations). Odour episodes occurred during low wind velocities and high humidity. Odours were most frequent during January-April, and were usually reported early in the morning. The odours were evidently due to the general operation of the plants, as no single activity or in-plant factor could be identified as the source of the odours.     

Seasonal Source-Receptor Relationships in a Petrochemical Industrial District over Northern Taiwan

Abstract

This study investigated the relationships between meteorological data, pollution sources, and receptors over northern Taiwan. During the intensive sampling period in summer 1992, the weather was controlled predominantly by a Pacific subtropical high and by Typhoon Mark. During the other intensive sampling period in winter 1993, while a cold frontal system approached Taiwan, the northeasterly winds prevailed most of the time. The local circulation such as land-sea breeze only developed under weak synoptic environment. Particle concentrations and element composition in winter were higher than in summer. This can be attributed to the high convection of air mass, which leads to the vertical dispersion of pollutants in summer. In addition to the subtropical high pressure, typhoons are frequently accompanied with high-wind speeds and unstable weather conditions that also dilute and eliminate the pollutants. In winter, the prevailing northeasterlies might carry pollutants from Midland China. Furthermore, the anticyclone system develops a stagnant condition that easily leads to pollutant accumulation. In this case, the wind direction affected the source contribution of the receptor and the PM₁₀ displays a higher correlation with coarse and fine particulate than meteorological parameters in summer. In addition, the mixing height shows a high correlation with PM₁₀ in winter.     

Emission Characteristics of Granulated Fuel Produced from Sewage Sludge and Coal Slime

Abstract

The neutralization of wastewater treatment residues is an issue for many countries. The European Union (EU) legal regulations have limited the use of the residues in agriculture and implemented a ban for their disposal. Therefore, urgent action should be taken to find solutions for the safe disposal of sewage sludge. The problem refers in particular to the new EU member countries, including Poland, where one can now observe an intensive development of sewage system networks and new sewage treatment plants. At the same time, these countries have few installations for thermal sewage sludge utilization (e.g., there is only one installation of that type in Poland). Simultaneously, there are many coal-fired mechanical stoker-fired boilers in some of these countries. This paper presents suggestions for the production of granulated fuel from sewage sludge and coal slime. Additionally, among others, lime was added to the fuel to decrease the sulfur compounds emission. Results are presented of research on fuel with two average grain diameters (～15 and 35 mm). The fuel with such diameters is adapted to the requirements of the combustion process taking place in a stokerfired boiler. The research was aimed at identifying the behavior of the burning fuel, with special attention paid to its emission properties (e.g., to the emissions of oxides of nitrogen [NO_x], sulfur dioxide [SO₂], and carbon mon-oxide [CO], among others). The concentration and emission values were compared with similar results obtained while burning hard coal. The combustion process was carried out in a laboratory stand where realization of the large-scale tests is possible. The laboratory stand used made simulation possible for a wide range of burning processes in mechanical stoker-fired boilers.     

Combustion Characteristics of Spent Catalyst and Paper Sludge in an Internally Circulating Fluidized-Bed Combustor

Abstract

Combustion of spent vacuum residue hydrodesulfurization catalyst and incineration of paper sludge were carried out in thermo-gravimetric analyzer and an internally circulating fluidized-bed (ICFB) reactor. From the thermogravimetric analyzer-differential thermo-gravimetric curves, the pre-exponential factors and activation energies are determined at the divided temperature regions, and the thermo-gravimetric analysis patterns can be predicted by the kinetic equations. The effects of bed temperature, gas velocity in the draft tube and annulus, solid circulation rate, and waste feed rate on combustion efficiency of the wastes have been determined in an ICFB from the experiments and the model studies. The ICFB combustor exhibits uniform temperature distribution along the bed height with high combustion efficiency (>90%). The combustion efficiency increases with increasing reaction temperature, gas velocity in the annulus region, and solid circulation rate and decreases with increasing waste feed rate and gas velocity in the draft tube. The simulated data from the kinetic equation and the hydrodynamic models predict the experimental data reasonably well.     

Combustion Kinetics and Emission Characteristics of Polycyclic Aromatic Hydrocarbons from Polylactic Acid Combustion

Abstract

This study investigates the combustion kinetics and emission factors of 16 U.S. Environmental Protection Agency priority polycyclic aromatic hydrocarbons (PAHs) in polylactic acid (PLA) combustion. Experimentally, two reactions are involved in the PLA combustion process that potentially result in the release of lactide, acetaldehyde, and n-hexaldehyde. The products may continuously be oxidized to form carbon dioxide (CO₂) and some PAHs produced because of incomplete combustion. The analytical results indicate that the emission factors for PAHs are in the range of not detectable to 98.04 μg/g. The emission factors are much lower than those of poly(ethylene terephalate) (PET) and other combustion of plastics. Results from this work suggest that combustion is a good choice for waste PLA disposal.     

固体废弃物轮胎的热解技术

综述了国内外对废轮胎的处理状况，并详细地讨论了废轮胎热解技术的发展、分类以及典型工艺流程。热解技术主要包括油化技术、气化技术和炭化技术三种，并可制得衍生油、燃料气、碳黑等产品。分析了废轮胎热解工艺存在的问题，指出了如何开发环境友好的集成工艺是废轮胎热解工艺的发展方向。     

含油岩屑热解特性与资源化

采用热红联用技术（TG-FTIR）对含油钻井岩屑进行热重实验研究,通过失重率（TG）曲线、失重速率（dTG）曲线获得其相关热解参数,通过FTIR图谱定性分析热解产物;进一步通过热解实验,对含油岩屑热解产物进行定量分析。实验结果表明,根据热解产物的不同可将含油岩屑热解过程分为3个阶段：低温段（25~350℃）、中温段（350~650℃）以及高温段（650~800℃）。其热解气体产物以一氧化碳和甲烷为主,冷凝液体产物主要为烃类与芳香族化合物。并探讨了含油岩屑经热解处理后产物资源化利用的方法。     

The Autothermal Pyrolysis of Waste Tires

Abstract

The growing amount of rubber waste, such as that from tires and cables, has resulted in serious environmental problems. Since rubber waste is not easily biodegradable even after a long period of landfill treatment, material and energy recovery is the preferable alternative to disposal. The potential offered by waste tire pyrolysis for solving both energy and waste treatment problems is widely recognized. Pyrolysis is one method of inducing thermal decomposition without using any oxidizing agent, or using such a limited supply of the agent that oxidization does not proceed to an appreciable extent. The latter may be described as autothermal pyrolysis and will be studied in the present work.

The main objective of this research was to study the operating parameters of autothermal pyrolysis of scrap tires in a laboratory-scale fluidized bed reactor with a 100-cm bed height (10 cm I.D.) and a 100-cm freeboard (25 cm I.D.). Scrap tires were pyrolyzed in a limited oxygen supply, so that the heat for pyrolysis of the scrap tires was provided by combustion of some portion of the scrap tires. The operating parameters evaluated included the effect on the pyrolysis oil products and their relative proportions of (1) the air factor (O.O7–O35); (2) the pyrolysis temperature (370–570 °C); and (3) the catalyst added (zeolite and calcium carbonate). The results show that: (1) the composition of the liquid hydrocarbon obtained is affected significantly by the air factor; (2) the higher operating temperature caused a higher yield of gasoline and diesel; (3) the yield of gasoline increased due to the catalyst zeolite added, and the yield of diesel increased due to the addition of the catalyst calcium carbonate; (4) the principal constituents of gasoline included dipentene and diprene.     

茉莉花茶废弃物的热解特性及其产物

为了探讨茉莉花茶废弃物的热解过程及温度对产物的影响,采用固定热解反应器和热重红外联用仪（TG-FTIR）对其进行了研究,结果表明,茉莉花茶废弃物解产生的固体量随温度升高而降低,气体产量随温度升高而增加,热解得到的液体量比例随热解温度不同而不同,表明茉莉花茶热解产物随热解温度不同而不同。热解产物主要有CO2、水、醇及含CC 的有机物和生物焦固体。500 ℃下制得的生物焦比表面积较低,仅为0.720 9 m2·g-1,经活化处理后的生物焦比表面积明显增大。经CO2和H2O活化后得到的生物焦的BET比表面积分别升至139.503 3 m2·g-1和122.527 6 m2·g-1。茉莉花茶热解的质量损失主要由于有机物挥发,用Coats-Redfern法对茉莉花茶废弃物热解过程进行模拟,得热解过程符合气体扩散模型,热解活化能约为60 kJ·mol-1;因此,气体扩散是茉莉花茶废弃物热解过程中主要的限制因素。     

污水污泥裂解及其性能的研究

以碘吸附值为裂解残渣吸附性能的指标,通过单因素实验和正交实验,确定了制备裂解残渣的最佳工艺条件,并对残渣的表面元素组成、孔结构组成、晶相组成和吸附性能等性质进行了表征。结果显示：以浓度均为5 mol/L的ZnCl₂和H₂SO₄作活化剂、复配比2∶1、活化温度600℃、活化时间1 h、固液比1∶2.5,制得的裂解残渣酸洗后碘值平均值可达892.8 mg/g;用制备的裂解残渣对苯酚废水进行处理,室温下振荡5 min,苯酚去除率即可达到87.9%,且符合Langmuir吸附等温线方程和Freundlich吸附等温线方程。     

Pyrolysis kinetics and residue characteristics of petrochemical industrial sludge

This study investigated the pyrolysis characteristics of sludge from wastewater treatment plants in the petrochemical industry and focused on the pyrolysis kinetics, elemental composition of residue, and volatile organic compounds (VOCs) of exhaust gas. As pyrolysis temperature increased to 773 K, the increasing rate of crude oil production tended to a stable condition. The result indicated that the optimal temperature of crude oil and water mixed production was 773 K. When pyrolysis temperature increased from 673 to 973 K, carbon, oxygen, nitrogen, and hydrogen concentrations of residue decreased and the sulfur concentration of residue increased. The concentrations of benzene, toluene,ethylbenzene, and styrene increased by the increasing pyrolysis temperature. We found that the reaction order of sludge pyrolysis was 2.5 and the activation energy of the reaction was 11.06 kJ/mol. We believe that our pyrolysis system is transitional between devolatilization and combustion.     

废聚氨酯的热解及产物分析

利用热重分析仪和管式炉对废聚氨酯进行热解实验,研究了废聚氨酯的热解特性及热解产物.结果表明,废聚氨酯热解有3个失重阶段,热失重主要发生在200～440℃,600℃热失重趋于稳定.红外光谱图分析发现,热解过程中有大量CO和CO2产生.气质联用检测结果分析显示,热解产物复杂,液体产物中检出苯胺、p-苯胺、苯甲腈等多种芳香类化合物,气体产物以低碳的烷烃和烯烃为主,还检测出有机氯化合物,这是废聚氨酯中氟利昂类发泡剂所致.     

Pyrolysis and combustion of Aroclor 1254 contaminated dielectric fluids

Pyrolysis and combustion products were determined for several levels of PCB contamination in mineral oil and other dielectric fluids. Yields of PCDFs were roughly proportional to the quantity of PCB in the feed.     

有机固体废弃物的热解处理研究

通过对锯末、稻壳、纸屑、橱芥、塑料和橡胶6种具有代表性的有机固体废弃物原料的热解实验,测量了它们三相产物收率,并分析了它们固体、液体和气体三相产物的组成.特别对液体产物,针对它们的特殊性分别采用了层析、模拟蒸馏和全烃气相色谱分析,详细探讨了热解焦油的具体组分,得到了热解法处理有机固体废弃物的一些有意义的数据.     

Pyrolysis of humic acids from digested and composted sewage sludge

Humic acids (HAs) were extracted from four digested sewage sludge samples composted for four months, one, two and four years. HAs were pyrolyzed at three different temperatures applying both conventional and in situ methylation (ISM) pyrolysis. The pyrolysates were analyzed using gas chromatography-mass spectrometry (GC/MS). Derivatization (ISM) and pyrolysis temperature had dramatic effects on the composition and relative amounts of the pyrolysates. Among the derivatized HA fragments aliphatic compounds prevailed under all the pyrolysis conditions tested. Aromatic substances consisting mainly of guaiacyl-type compounds were detected in higher abundances only at elevated temperatures. Without ISM the contribution of aromatic structures to the total pyrogram was considerably greater than that of the aliphatics. Increase of the pyrolysis temperature from 450 degrees C to 600 degrees C had smaller effect on the proportions and composition of the compounds studied than increase from 350 degrees C to 450 degrees C.     

船舶塑料垃圾热解特性及动力学分析

利用热重分析(TGA)研究船舶塑料垃圾在不同升温速率和不同气氛下的热解特性,并得到了热解动力学参数。结果表明,船舶塑料垃圾的热解过程主要有3个阶段,比一般塑料热解复杂;随着升温速率增大,最大热解速率和最大热解速率温度等热解特性参数也增大,反应变得更剧烈;N2/CO2比为4∶1时,热解反应进行得最完全,固体残留率最少。动力学分析表明,采用3个连续一级反应模型能很好地拟合实验数据;不同的升温速率和气氛比对反应各阶段活化能均有不同程度的影响。     

工业废水污泥的热解及升温速率对热解的影响

利用热重分析法对印染、中药和废水处理厂3种典型工业废水污泥进行了热解动力学实验研究。结果表明,工业污泥是一种高挥发分、低固定碳和低热值的劣质燃料。经过消化处理的污泥灰分含量较高,挥发分含量变小。热解过程中有3个失重速率较高的阶段,以挥发分的析出为主。升温速率对热解的最终失重率有重要影响。升温速率增加,热解更剧烈,但最终失重率的变化趋势与污泥种类有关;为使热解效果更好,不同种类的污泥应选择不同的升温速率。不同种类的污泥具有不同的热解特性,印染污泥挥发分析出阶段有2次热解。中药污泥活化能最小,印染污泥挥发分第2次热解的活化能比第1次大幅增加。     

食用菌废菌棒热解的产物分布与机理解析

我国食用菌废菌棒产生量大,利用率低,对环境污染严重,需要妥善处理。为制备高品质能源,在500~800 ℃温度范围内快速热解废菌棒,分析产物特征,解析热解机理。热解温度从500 ℃上升到800 ℃时,废菌棒的热解气质量分数从18.44%上升到50.45%,焦油的质量分数从49.06%下降到23.72%,生物炭的质量分数维持在30%左右,废菌棒的质量减量化率超过2/3;同时,热解气中H2、CO、CH4含量均有上升,CO2含量下降;焦油组分向更稳定的苯系物转变;生物炭炭化效果增强。研究结果表明,700 ℃为最佳热解温度,经过120 s即可反应完全。高温可以破坏羟基的结构,使其发生脱氢反应,碳氢键较早断裂,伯碳和仲碳大量裂解并迁移至焦油和热解气中,羰基在高温下迅速断链。     

不同油田油泥热裂解的特性分析及动力学研究

油泥是石油行业的产物,具有产量大、污染严重、处理困难等特点。运用热处理方法进行实验,通过对两个不同油田油泥的热裂解实验,发现不同来源的油泥,其组分与形态差异十分明显,从而导致热解结果也有一定的差异。经热解处理后,油泥质量减少50%~80%,减量化明显;通过释放气体的分析,对热解的反应历程以及反应机理做出了初步推测。最后通过动力学分析,得到了一定的动力学参数,为实际操作中的问题解决提供实践依据,从而提高该技术的适用性与实用性。