Analysis of long-term settlement of municipal solid waste landfills as determined by various settlement estimation methods

In this study, several existing municipal solid waste (MSW) settlement estimation methods are reviewed and applied to analyze the settlement data of nine MSW landfills. Because a biodegradation-related settlement contributes differently to a long-term total settlement depending on the age of landfills, the actual MSW landfill sites are classified into three groups to specifically address the validity of each method in its prediction of a long-term settlement for each age category. Results demonstrate that there are considerable decreases in predicted settlement potentials as fill age increases. Comparisons indicate that the individual estimation methods display a considerable variation in predicting settlements in the fresh MSW landfills. On the other hand, for the old refuse landfills, all of the estimation methods, except the extended soil model, predict low settlement potentials.     

Methane Emissions from Domestic Waste Management Facilities in Jordan—Applicability of IPCC Methodology

ABSTRACT

In this paper, methane emissions from municipal wastewater treatment plants and municipal solid waste (MSW) landfills in Jordan for 1994 have been estimated using the methodology developed by the Intergovernmental Panel on Climate Change (IPCC). For this purpose, the 14 domestic wastewater treatment plants in the country were surveyed. Generation rates and characterization of MSW components as well as dumping and landfilling practices were surveyed in order to estimate 1994 CH₄ emissions from these sites. Locally available waste statistics were used in cases where those of the IPCC guidelines were not representative of Jordan's statistics.

Methane emissions from domestic wastewater in Jordan were estimated at 4.66 gigagrams (Gg). Total 1994 CH₄ emissions from MSW management facilities in Jordan are estimated at 371.76 Gg—351.12 Gg (94.45%) from sanitary landfills, 19.83 Gg (5.33%) from MSW open dumps, and 0.81 Gg (0.22%) from raw sewage-water dumping ponds. Uncertainties associated with these estimations are presented.     

A survey of municipal solid waste landfills in Beijing during 2009–2011

The investigation of municipal solid waste (MSW) treatment in China is rare due to its sensitivity and difficulty in terms of access. We chose Beijing, the capital of China, as an example to identify the characteristics of MSW landfill treatments using a 2-month investigation with 20 participants. MSW landfill treatments account for nearly 70% of the annual MSW disposal in Beijing; the landfill processes are equipped with many kinds of technologies and consume a large amount of energy and produce a variety of contaminants. The cover method (the most obvious difference in landfill tamping) mainly includes high-density polyethylene (HDPE) geomembranes with loess and soil alone (i.e., loess or sandy soil). We investigated the actual conditions of landfills and collected data on leachate and landfill gas (LFG) emissions and energy consumption during 2009–2011. The results indicated that the cover method employed by landfills was related to treatment quantity, operation, and especially landfill location. Early large-scale landfills located in plains were covered with HDPE geomembranes, and newly built landfills covered with soil tended to be equipped with HDPE covers. Using HDPE cover also contributed greatly to LFG production due to its impermeability but had no remarkable effect on leachate yield reduction due to the dry climate in Beijing. The potential was reinforced by the potentials of decrement and reuse. The disposal method of LFG can be optimized, and the power generated by the LFG process can meet the landfill demand. The gray water recycled from the leachate could be used in the landfill process.

     

Evaluation of Solid Waste Management Strategies in the Taipei Metropolitan Area of Taiwan

Abstract

Chenfang Lin is with the Department of Soil and Environmental Science at National Chung Hsing University.Municipal solid waste (MSW) management is a major concern for highly urbanized societies. Among proposed MSW management systems, regionalization programs generally have received considerable attention. This study analyzes real-world operational data to assess different MSW management policies, especially regionalization strategies, and their impact on MSW management systems in the Taipei metropolitan area. Linear programming is also used to identify the minimum costs sustained by each policy. The linear programming results show that regionalization programs are more economical and also improve incinerator operation efficiency. Sensitivity analysis indicates that the minimum treatment requirement of incinerators is a very sensitive influence on the MSW flows distributed through the entire region. The MSW of several “sensitive” administrative districts will be allocated to different treatment facilities according to different management strategies. A list of preferential sequences of MSW treatment and disposal facilities can also be identified by the model presented in this study. The results of this study may provide a useful tool for aiding decision-making related to real-world MSW management problems.     

Municipal solid waste management planning for Xiamen City,China: a stochastic fractional inventory-theory-based approach

In this study, a stochastic fractional inventory-theory-based waste management planning (SFIWP) model was developed and applied for supporting long-term planning of the municipal solid waste (MSW) management in Xiamen City, the special economic zone of Fujian Province, China. In the SFIWP model, the techniques of inventory model, stochastic linear fractional programming, and mixed-integer linear programming were integrated in a framework. Issues of waste inventory in MSW management system were solved, and the system efficiency was maximized through considering maximum net-diverted wastes under various constraint-violation risks. Decision alternatives for waste allocation and capacity expansion were also provided for MSW management planning in Xiamen. The obtained results showed that about 4.24 × 10⁶ t of waste would be diverted from landfills when p _i is 0.01, which accounted for 93% of waste in Xiamen City, and the waste diversion per unit of cost would be 26.327 × 10³ t per $10⁶. The capacities of MSW management facilities including incinerators, composting facility, and landfills would be expanded due to increasing waste generation rate.     

Remedial Strategies for Municipal Solid Waste Management in China

ABSTRACT

The purpose of this investigation is to evaluate the current status and to identify the problems of municipal solid waste (MSW) management in China to determine appropriate remedial strategies. This is the second of two papers proposed on this topic. Major problems or difficulties identified in MSW management in China include MSW land, air, and water pollution, commingled collection, poor administration, shortage of funds, lack of facilities, and problems of training and public awareness.

In order to solve these problems and to improve MSW management in China, remedial strategies in three areas are recommended: institutional reform, technology development, and legislation and administrative improvement. The primary principle involved in institutional reform is unifying legislative responsibilities into one body and developing a market mechanism for handling MSW. Composting, landfills, and incineration should be equally developed in accordance with China's needs. The feasibility of developing technology to handle MSW in China is discussed. Also recommended is the establishment of sound regulatory systems, including a service fee system, a source separation system, and a training program. China is presently undergoing economic and institutional reform at the national and local levels. Results of this study will provide useful information on MSW management in China.     

Factors Influencing Regional Municipal Solid Waste Management Strategies

Abstract

Although regionalization policies have been proven as good strategies for municipal solid waste (MSW) management in previous studies, the optimal allocation of the waste stream is significantly affected by several influential factors, thus further investigation of the impacts of these factors on regional MSW management strategies is necessary. This study demonstrated the impacts of waste-to-electricity transformation coefficient (WETC) of incinerators and the fluctuation of unit tipping fees on the regional MSW flow/allocation of the Taipei metropolitan area from practical and economic perspectives. Real-world data and linear programming were used to obtain the least-cost alternatives under different scenarios. Analytical results indicated some treatment facilities had geographic superiority and their priorities changed when actual WETCs of incinerators were considered. Treatment facilities located at weighted centers were identified. The allocation of MSW among incinerators and landfills is affected by fluctuation of unit tipping fees within a certain range. Treatment facilities sensitive to the changes in unit tipping fees were also identified. Regression equations were also established that can estimate the cost items of MSW management scenarios with different unit tipping fees. The results of this study are very useful for daily basis regulation of MSW administration.     

Comparison of Aerobic and Anaerobic Biotreatment of Municipal Solid Waste

Abstract

To increase the operating lifetime of landfills and to lower leachate treatment costs, an increasing number of municipal solid waste (MSW) landfills are being managed as either aerobic or anaerobic bioreactors. Landfill gas composition, respiration rates, and subsidence were measured for 400 days in 200-L tanks filled with fresh waste materials to compare the relative effectiveness of the two treatments. Tanks were prepared to provide the following conditions: (1) air injection and leachate recirculation (aerobic), (2) leachate recirculation (anaerobic), and (3) no treatment (anaerobic). Respiration tests on the aerobic wet tank showed a steady decrease in oxygen consumption rates from 1.3 mol/day at 20 days to 0.1 mol/day at 400 days. Aerobic wet tanks produced, on average, 6 mol of carbon dioxide (CO₂)/kg of MSW as compared with anaerobic wet tanks, which produced 2.2 mol methane/kg of MSW and 2.0 mol CO₂/kg methane. Over the test period, the aerobic tanks settled on average 35%, anaerobic tanks settled 21.7%, and the no-treatment tank settled 7.5%, equivalent to overall mass loss in the corresponding reactors. Aerobic tanks reduced stabilization time and produced negligible odor compared with anaerobic tanks, possibly because of the 2 orders of magnitude lower leachate ammonia levels in the aerobic tank. Both treatment regimes provide the opportunity for disposal and remediation of liquid waste.     

An economic evaluation and assessment of environmental impact of the municipal solid waste management system for Taichung City in Taiwan

Municipal solid waste management (MSWM) is an important environmental challenge and subject in urban planning. For sustainable MSWM strategies, the critical management factors to be considered include not only economic efficiency of MSW treatment but also life-cycle assessment of the environmental impact. This paper employed linear programming technique to establish optimal MSWM strategies considering economic efficiency and the air pollutant emissions during the life cycle of a MSWM system, and investigated the correlations between the economical optimization and pollutant emissions. A case study based on real-world MSW operating parameters in Taichung City is also presented. The results showed that the costs, benefits, streams of MSW, and throughputs of incinerators and landfills will be affected if pollution emission reductions are implemented in the MSWM strategies. In addition, the quantity of particulate matter is the best pollutant indicator for the MSWM system performance of emission reduction. In particular, this model will assist the decision maker in drawing up a friendly MSWM strategy for Taichung City in Taiwan.

Implications: Recently, life-cycle assessments of municipal solid waste management (MSWM) strategies have been given more considerations. However, what seems to be lacking is the consideration of economic factors and environmental impacts simultaneously. This work analyzed real-world data to establish optimal MSWM strategies considering economic efficiency and the air pollutant emissions during the life cycle of the MSWM system. The results indicated that the consideration of environmental impacts will affect the costs, benefits, streams of MSW, and throughputs of incinerators and landfills. This work is relevant to public discussion and may establish useful guidelines for the MSWM policies.     

Compressibility of municipal solid waste codisposed with fly ash

If a municipal solid waste (MSW) landfill is used as the foundation for a construction site, the change in the loading conditions may cause considerable compression of the landfill. Therefore, reinforcement to compensate for the loose compression nature of a MSW landfill is a very important design factor for geotechnical engineers when considering the end-use of the landfill. In this study, we discuss a possible technique for stabilizing MSW landfills through the codisposal of municipal solid waste and fly ash. To estimate the stabilization based on the compression characteristics of the codisposed landfill, we performed tests using a large compression set and experimental cells. According to the test results, if the proportion of fly ash is increased, initial and long-term compression could be reduced.     

Effect of biogas generation on radon emissions from landfills receiving radium-bearing waste from shale gas development

Dramatic increases in the development of oil and natural gas from shale formations will result in large quantities of drill cuttings, flowback water, and produced water. These organic-rich shale gas formations often contain elevated concentrations of naturally occurring radioactive materials (NORM), such as uranium, thorium, and radium. Production of oil and gas from these formations will also lead to the development of technologically enhanced NORM (TENORM) in production equipment. Disposal of these potentially radium-bearing materials in municipal solid waste (MSW) landfills could release radon to the atmosphere. Risk analyses of disposal of radium-bearing TENORM in MSW landfills sponsored by the Department of Energy did not consider the effect of landfill gas (LFG) generation or LFG control systems on radon emissions. Simulation of radon emissions from landfills with LFG generation indicates that LFG generation can significantly increase radon emissions relative to emissions without LFG generation, where the radon emissions are largely controlled by vapor-phase diffusion. Although the operation of LFG control systems at landfills with radon source materials can result in point-source atmospheric radon plumes, the LFG control systems tend to reduce overall radon emissions by reducing advective gas flow through the landfill surface, and increasing the radon residence time in the subsurface, thus allowing more time for radon to decay. In some of the disposal scenarios considered, the radon flux from the landfill and off-site atmospheric activities exceed levels that would be allowed for radon emissions from uranium mill tailings.

Implications: Increased development of hydrocarbons from organic-rich shale formations has raised public concern that wastes from these activities containing naturally occurring radioactive materials, particularly radium, may be disposed in municipal solid waste landfills and endanger public health by releasing radon to the atmosphere. This paper analyses the processes by which radon may be emitted from a landfill to the atmosphere. The analyses indicate that landfill gas generation can significantly increase radon emissions, but that the actual level of radon emissions depend on the place of the waste, construction of the landfill cover, and nature of the landfill gas control system.     

Real-time measurements of landfill atmospheric ammonia using mobile white cell differential optical absorption spectroscopy system and engineering applications

ABSTRACT

The real-time measurement of atmospheric ammonia at municipal solid waste (MSW) landfills and adjacent areas is necessary for landfill management and the health of nearby residence. Continuous, fast, and real-time monitoring of landfill odor gases is a challenge, especially for ammonia. To our knowledge, this was the first study for the characteristics and seasonal variabilities of atmospheric ammonia at a whole landfill using a Mobile White cell Differential Optical Absorption Spectroscopy (MW-DOAS) system, which also simultaneously offers high sensitivity and fast response. Results show that atmospheric ammonia levels at various landfill areas were significantly dependent on the characteristics of areas, such as municipal solid waste-related areas, leachate-related areas, sludge-related areas, and fly ash-related area, the atmospheric ammonia peak or average level at the active leachate pool of the active MSW site was the highest among all areas of the whole landfill, and the ammonia concentrations at the closed MSW landfill sites were low and dependent on the ages. Moreover, it was found that the seasonal variabilities of ammonia concentrations at most of those areas were significantly dependent on the ambient temperature, and ambient temperature variation caused the atmospheric ammonia level at the active leachate pool and active MSW landfill site in the summer survey to raise 3.5 times and 5.58 times than in the winter survey, respectively.

Implications: Continuous, fast, and real-time monitoring ambient ammonia at or nearby a landfill is critical for landfill operators and local EPAs. This study demonstrates that the mobile White cell Differential Optical Absorption Spectroscopy (MW-DOAS) system is an effective tool for real-time monitoring ambient ammonia of a whole landfill. The results in this article provided a guideline to the characteristics and seasonal changes of ambient ammonia at various types of areas of a whole landfill as well as the impact of age to ambient ammonia at the closed landfill areas.     

An Optimal Model and Its Application for the Management of Municipal Solid Waste from Regional Small Cities in China

Abstract

Based on the basic characteristics of municipal solid waste (MSW) from regional small cities in China, some optimal management principles have been put forward: regional optimization, long-term optimization, and integrated treatment/disposal optimization. According to these principles, an optimal MSW management model for regional small cities is developed and provides a useful method to manage MSW from regional small cities. A case study application of the optimal model is described and shows that the optimal management scenarios in the controlling region can be gained, adequately validating and accounting for the advantages of the optimal model.     

Minimax Regret Analysis for Municipal Solid Waste Management: An Interval-Stochastic Programming Approach

Abstract

In this study, an interval minimax regret programming (IMMRP) method is developed for the planning of municipal solid waste (MSW) management under uncertainty. It improves on the existing interval programming and minimax regret analysis methods by allowing uncertainties presented as both intervals and random variables to be effectively communicated into the optimization process. The IMMRP can account for economic consequences under all possible scenarios without any assumption on their probabilities. The developed method is applied to a case study of long-term MSW management planning under uncertainty. Multiple scenarios associated with different cost and risk levels are analyzed. Reasonable solutions are generated, demonstrating complex tradeoffs among system cost, regret level, and system-failure risk. The method can also facilitate examination of the difference between the cost incurred with identified strategy and the least cost under an ideal condition. The results can help determine desired plans and policies for waste management under a variety of uncertainties.     

A Sampling Protocol for Composting,Recycling, and Re-use of Municipal Solid Waste

Abstract

This article reports on development of a protocol for characterizing municipal solid waste (MSW). This protocol is similar to that recommended by the American Society for Testing and Materials but includes a distinction between pure and mixed loads of MSW. Thirteen component categories were used with a focus on material feed stock for composting, recycling, and reuse. The required number of samples was determined to achieve a 80%, 90%, and 95% statistical accuracy for characterizing MSW categories at 1% and 2% sampling error. This study found that a maximum of 25 randomly collected samples of 200 pounds will reflect each component category of mixed load MSW with at least a 95% confidence level and 2% error. This protocol was successfully tested in Monongalia County, West Virginia, to provide a “snapshot” MSW characterization during early summer.     

Polymers as Solid Waste in Municipal Landfills

Abstract

Synthetic polymers reach municipal landfills as components of products such as waste household paints, packaging films, storage containers, carpet fibers, and absorbent sanitary products. Some polymers in consumer products that reach landfills are designed to photodegrade or biodegrade. This article examines the significance of degradable polymers in management of solid waste in municipal landfills. Most landfills are not designed to photodegrade or biodegrade solid waste. Landfill disposal of stable polymers such as polyacrylics and polyethylenes is not associated with significant polymer degradation or mobility. Stability to photodegradation and biodegradation is an advantage when municipal landfills are used for disposal of polymer products as solid waste. Use of landfill disposal can be a responsible means to manage polymer waste and can be part of an overall waste management plan which includes source reduction, recycling, reuse, composting, and waste-to-energy incineration.     

Comparison of variability in dioxin and furan data acquired using single train and simultaneous multiple train stack sampling methods

The variance of polychlorinated dibenzo-p-dioxin (PCDD; dioxin) and polychlorinated dibenzofuran (PCDF; furan) data obtained from single- and simultaneous multiple train methods was compared. Single train triplicate data were used from 4 stack tests obtained from a long dry kiln cement plant and 18 stack tests from a municipal solid waste (MSW) incinerator. Data from the American Society of Mechanical Engineers (ASME) report Reference Method Accuracy and Precision (ReMAP) (Lanier and Hendrix, 2001) were used for the simultaneous multiple samples, which accounted for 27 data points. Nineteen data points were acquired from an ASME research facility, 5 from a MSW incinerator unrelated to the single train MSW incinerator, and 3 from a lightweight aggregate kiln (LWAK). The ReMAP procedure was used to determine the relationship between the standard deviation and the concentration of the single train and simultaneous multiple train data. Results indicated that there was benefit from the use of simultaneous multiple train sampling for concentrations above 129 pg toxic equivalency (TEQ)/m³. There was no indication of benefit from the use of simultaneous multiple train sampling at concentrations below 129 pg TEQ/m³.

Implications:Precision of stack sampling data can be the difference between meeting and failing compliance limits. Generally, three dioxin/furan samples are acquired when stack sampling to meet compliance regulations. A reliable estimation of the data’s true concentration is not possible with this small amount of data. Increasing the precision decreases the chance that the acquired concentration deviates greatly from the true concentration. Facilities that use the appropriate stack sampling method will benefit by either improved data precision or minimal stack sampling expenses. The observations made suggest that facilities that are expected to have dioxin/furan concentrations above 129 pg TEQ/m³ would increase the precision of samples by using simultaneous multiple train sampling.     

A Life-Cycle Inventory Model of Municipal Solid Waste Combustion

ABSTRACT

Evaluation of alternate strategies for municipal solid waste (MSW) management requires models to calculate environmental emissions as a function of both waste quantity and composition. A methodology to calculate waste component-specific emissions associated with MSW combustion is presented here. The methodology considers emissions at a combustion facility as well as those avoided at an electrical energy facility because of energy recovered from waste combustion. Emission factors, in units of kg pollutant per metric ton MSW entering the combustion facility, are calculated for CO₂-biomass, CO₂-fossil, SO_x , HCl, NO_x , dioxins/furans, PM, CO, and 11 metals. Water emissions associated with electrical energy offsets are also considered. Reductions in environmental emissions for a 500-metric-ton-per-day combustion facility that recovers energy are calculated.     

83rd Annual Meeting & Exhibition

Abstract

The estimation of odor production and dispersion from landfill sites is a very complicated task because of the different chemical species that exist in biogas. To site a new landfill, it is necessary to know the distance that odors can travel around the landfill under atmospheric conditions that increase the concentration of pollutants. Although CH₄ is an odorless gas, it can be used as an index to determine the dispersion of low-reactivity odorous species around a landfill site. Methane production rates, estimated by biogas production models, were used by an air dispersion model to determine the spatial distribution of CH₄ around landfill sites. By utilizing dispersion models under extreme atmospheric conditions, a maximum CH₄ concentration around the landfills was determined. Based on the ratio between CH₄ and odorous chemical species, the spatial distribution of the concentration of an odorous species was determined for those species with low reactivity in the atmosphere. For odorous species with high reactivity in the atmosphere, a dispersion-reaction model must be used. In this way, the acceptable distance between new landfills and residential areas can be determined. The proposed methodology could be used as a design tool for those who are interested in landfill siting.     

Methane emissions from domestic waste management facilities in Jordan--applicability of IPCC methodology

In this paper, methane emissions from municipal wastewater treatment plants and municipal solid waste (MSW) landfills in Jordan for 1994 have been estimated using the methodology developed by the Intergovernmental Panel on Climate Change (IPCC). For this purpose, the 14 domestic wastewater treatment plants in the country were surveyed. Generation rates and characterization of MSW components as well as dumping and landfilling practices were surveyed in order to estimate 1994 CH4 emissions from these sites. Locally available waste statistics were used in cases where those of the IPCC guidelines were not representative of Jordan's statistics. Methane emissions from domestic wastewater in Jordan were estimated at 4.66 gigagrams (Gg). Total 1994 CH4 emissions from MSW management facilities in Jordan are estimated at 371.76 Gg--351.12 Gg (94.45%) from sanitary landfills, 19.83 Gg (5.33%) from MSW open dumps, and 0.81 Gg (0.22%) from raw sewage-water dumping ponds. Uncertainties associated with these estimations are presented.