A fabric denuder for sampling semi-volatile species

A new style of diffusion denuder has been evaluated specifically for sampling HNO3. A coated fabric is used as the denuder substrate, which can be loaded directly into a standard filter holder. This approach allows direct denuder sampling with no additional capital costs over filter sampling and simplifies the coating and extraction process. Potential denuder materials and coatings were evaluated in the laboratory to test the removal efficiency. NaCl coatings were used to assess more than 20 materials for HNO3 collection efficiency. Particle retention, which would cause a denuder to have a positive bias for gas concentration measurements, was evaluated by ambient air sampling using particulate sulfate as the reference aerosol. Particle retention varied from 0 to 15%, depending on the denuder material tested. The best performing material showed an average particle retention of less than 3%. Denuder efficiency of four fabric materials was tested under ambient conditions to determine removal efficiency. The fabric denuder method was compared with a long path-length Fourier transform infrared (FTIR) spectrometer, a tunable diode laser absorption spectrometer (TDLAS), and a denuder difference sampler to independently measure HNO3. HNO3 collection efficiency was typically 90% for the denuders, whether coated with NaCl or not. For 10-L/min sampling rates with the fabric denuder, the square of the correlation coefficient with the FTIR spectrometer was 0.73, compared to 0.24 with the TDLAS.     

Comparing field performances of denuder techniques in the high Arctic

A field evaluation between two annular denuder configurations was conducted during the spring of 2003 in the marine Arctic at Ny-Ålesund, Svalbard. The IIA annular denuder system (ADS) employed a series of five single-channel annular denuders, a cyclone and a filter pack to discriminate between gas and aerosol species, while the EPA-Versatile Air Pollution Sampler (VAPS) configuration used a single multi-channel annular denuder to protect the integrity of PM_2.5 sample filters by collecting acidic gases. We compared the concentrations of gaseous nitric acid (HNO₃), nitrous acid (HONO), sulfur dioxide (SO₂) and hydrochloric acid (HCl) measured by the two systems. Results for HNO₃ and SO₂ suggested losses of gas phase species within the EPA-VAPS inlet surfaces due to low temperatures, high relative humidities, and coarse particle sea-salt deposition to the VAPS inlet during sampling. The difference in HNO₃ concentrations (55%) between the two data sets might also be due to the reaction between HNO₃ and NaCl on inlet surfaces within the EPA-VAPS system. Furthermore, we detected the release of HCl from marine aerosol particles in the EPA-VAPS inlet during sampling contributing to higher observed concentrations. Based on this work we present recommendations on the application of denuder sampling techniques for low-concentration gaseous species in Arctic and remote marine locations to minimize sampling biases. We suggest an annular denuder technique without a large surface area inlet device in order to minimize retention and/or production of gaseous atmospheric pollutants during sampling.     

Performance of the Annular Denuder System with Different Arrangements for HNO3 and HNO2 Measurements in Taiwan

ABSTRACT

Experiments on different annular denuder system (ADS)arrangements for sampling nitrous acid (HNO₂) and ni-tric acid (HNO₃) gases were conducted in this study toevaluate their sampling artifacts. The evaluation basis isthe one that employed one sodium chloride denuder forsampling HNO₃ gas and two sodium carbonate (Na₂CO₃)denuders for sampling HNO₂ gas, which is a commonlyemployed ADS arrangement in many field applicationsin the United States. A field study was conducted inHsinchu, Taiwan, and the results indicated that this ADSarrangement may yield over 80% relative errors for HNO₃gas. It also showed that the relative errors for HNO₂ gascan be less than 10% as sampled with only one Na₂CO₃denuder. This is attributed to the fact that the ambientHNO₃ concentration measured in this study was relativelylow while the HNO₂ concentration was high, as comparedto typical concentrations of these two gases measured inthe United States.

The sampling error of HNO₃ gas may be due to highconcentrations of N-containing interfering speciespresent in Taiwan’s atmosphere. Because the relative sam-pling errors of HNO₃ and HNO₂ gases depend mainly ontheir concentrations in the atmosphere as well as con-centrations caused by interfering species, the risk for higherror while measuring low HNO₂ concentrations by onlyone Na₂CO₃ denuder is also possible. As a result, it is sug-gested that pretests are necessary to evaluate possiblesources and degrees of sampling errors before fieldsampling of HNO₂ and HNO₃ gases. The sampling errorsof these two gases can, therefore, be minimized with abetter arrangement of the ADS.     

A theoretical evaluation on the HNO3 artifact of the annular denuder system due to evaporation and diffusional deposition of NH4NO3-containing aerosols

A mathematical model was developed to evaluate HNO₃ artifact of the annular denuder system due to evaporation and diffusional deposition of nitrate-containing aerosols. The model performance was validated by comparing its numerical solutions with laboratory and numerical data available in the literature for evaporation and diffusional deposition of monodisperse and polydisperse NH₄NO₃ aerosols. Measurement artifacts were evaluated by varying typical sampling ranges of ambient temperature, HNO₃ gas concentration, aerosol number concentration, aerosol mass median diameter, and nitrate mass fraction of <2.5 μm aerosols to see their respective effects. Potential application of the present model on estimating HNO₃ artifacts was demonstrated using literature data sampled in USA, Taiwan, Netherlands, Korea and Japan. Significant measurement artifact could be found in Taiwan and Netherlands due either to low HNO₃ gas concentration and high nitrate concentration in <2.5 μm aerosols or to high ambient temperature.     

HNO3 losses within the cyclone inlet of a diffusion-denuder system under simulated marine environments

We evaluated the loss of HNO₃ within a Teflon-coated aluminum cyclone of an annular diffusion denuder atmospheric sampling system (ADS) under simulated marine conditions. To simulate marine environment, the cyclones were pre-coated with NaCl aerosol droplets. Loss of vapor-phase HNO₃ within the NaCl-coated cyclone was generally greater than 30% at relative humidities (RH) of 60 and 80% and as large as 67% when the cumulative HNO₃ dosages were lower than 3 μg. In contrast, there was little loss of HNO₃ (<8%) in cyclones with no NaCl coating at RHs ranging from 0 to 80%, at HNO₃ air concentrations of 4.3±1.6 μg m⁻³, and at cumulative HNO₃ dosages of greater than 5 μg. However, at lower HNO₃ cumulative dosages (<3 μg), losses in the non-coated cyclones were strongly influenced by RH, ranging from 9% in dry air to 58% at 80% RH. The enhanced loss of HNO₃ in the NaCl-coated cyclone was most likely caused by the reaction between HNO₃ and NaCl on the cyclone wall.     

Use of Two Different Acidic Aerosol Samplers To Measure Acidic Aerosols in Hsinchu,Taiwan

ABSTRACT

Acidic aerosol concentrations measured by an annular denuder system (ADS) and a honeycomb denuder system (HDS) in Hsinchu, Taiwan, were compared. Aerosols were also sampled by a MOUDI (micro-orifice uniform deposit impactor) and analyzed by an ion chromatograph to determine the size distributions of different species. Using the measured aerosol size distribution, theoretical analysis showed that positive HNO₃ artifact due to volatiliza-tion of NH₄NO₃ is generally negligible for both samplers.4 3Comparing two different denuder samplers, the average concentration of HNO₃ measured by the ADS was found3to be lower than that measured by the HDS, while the difference between the two samplers for the average concentration of other species was found to be within ±15%. A possible cause of the difference in HNO₃ con-3centrations is due to a greater loss of HNO₃ in the cyclone3 used by the ADS than in the impactor used by the HDS. The study also showed incomplete absorption of the evaporated HCl and HNO₃ from the particles on the Teflon3filter by the first nylon filter in the filter pack of the ADS. Collection efficiency and capacity of HCl and HNO₃ by3the nylon filters need further investigation.     

Laboratory and field investigations of a new and simple design for the parallel plate denuder

Diffusion denuders are commonly used for collection of water soluble atmospheric gases. Denuder plates made of glass with silica coating were however difficult to handle in field measurements, and also had wettability problems. In this paper, we describe a new design of parallel plate denuder consisting of perfluoralkoxy (PFA) plates and polyester sheets. The parallel plate denuder was coupled on-line to ion chromatography for analysis of atmospheric HNO₃ and SO₂. With time resolution of 20 min, the detection limits for both gases were 6 ppt(v). Memory effect was found to be significant for HNO₃ especially at high humidity with the long sample inlet tube. Particle losses due to diffusion and electrostatic effects in the denuder were investigated and compared with theory. Particle loss in the sample inlet tube was found to play an important role by reducing the number of charged particles entering the denuder. The instrument was applied in two European Union field measurement campaigns, and the intercomparison results are presented in this paper.     

A Passive Flux Denuder for Evaluating Emissions of Ammonia at a Dairy Farm

Abstract

Passive samplers have been shown to be an inexpensive alternative to direct sampling. Diffusion denuders have been developed to measure the concentration of species such as ammonia (NH₃), which is in equilibrium with particulate ammonium nitrate. Conventional denuder sampling that inherently requires air pumps and, therefore, electrical power. To estimate emissions of NH₃ from a fugitive source would require an array of active samplers and meteorological measurements to estimate the flux. A recently developed fabric denuder was configured in an open tube to passively sample NH₃ flux. Passive and active samplers were collocated at a dairy farm at the California State University, Fresno, Agricultural Research Facility. During this comparison study, NH₃ flux measurements were made at the dairy farm lagoon before and after the lagoon underwent acidification. Comparisons were made of the flux measurements obtained directly from the passive flux denuder and those calculated from an active filter pack sampler and wind velocity. The results show significant correlation between the two methods, although a correction factor needed to be applied to directly compare the two techniques. This passive sampling approach significantly reduces the cost and complexity of sampling and has the potential to economically develop a larger inventory base for ambient NH₃ emissions.     

Simultaneous sampling of NH3, HNO3, HC1, SO2 and H2O2 in ambient air by a wet annular denuder system

A new sampling device is described for the simultaneous collection of NH₃, HNO₃, HCl, SO₂ and H₂O₂ in ambient air. The apparatus is based on air sampling by two parallel annular denuder tubes. The gases are collected by absorption in solutions present in the annulus of the denuder tubes. After a sampling time of 30 min at flow rate of 32 ℓ min⁻¹ the solutions are extracted from the denuders and analyzed off-line. The detection limits of NH₃, HNO₃, HCL and SO₂ are in the order of 0.1–0.5 μm⁻³. For H₂O₂ the detection limit is 0.01 μm⁻³. The reproducibility is 5–10% at the level of ambient air concentrations. Comparison of this novel technique with existing methods gives satisfactory results. The compact set-up offers the possibility of field experiments without the need of extensive equipment.     

A comparison of filter,denuder, and real-time chemiluminescence techniques for nitric acid determination in ambient air

Measurements of gas-phase nitric acid were made by four separate techniques during a 7-day summertime period at a near-coastal site on Long Island, NY. Results from methods intercomparison data for HNO₃, and their relationship to particulate NO₃⁻ and other odd N and oxidant species show the following: (a) high-volume filter pack HNO₃ concentrations are well correlated with diffusion denuder difference (DD) results, except for small absolute losses with the former; (b) daytime real-time two-channel chemiluminescence HNO₃ levels correlated well with DD results, but were higher during night-time periods; (c) results by a new Al₂(SO₄)₃ denuder/thermal evolution technique were not in agreement with other techniques. Based on HNO₃ and paniculate NO₃ results reported herein, it appears that negative errors in HNO₃filter-sampling techniques resulting from HNO₃ loss by sorption generally exceed positive errors NH₄NO₃ volatilization at this site.     

Determination of PM2.5 Sulfate and Nitrate with a PC-BOSS Designed for Routine Sampling for Semi-Volatile Particulate Matter

ABSTRACT

Ambient particles contain substantial quantities of material that can be lost from the particles during sample collection on a filter. These include ammonium nitrate and semi-volatile organic compounds. As a result, the concentrations of these species are often significantly in error for results obtained with a filter pack sampler. The accurate measurement of these semi-volatile fine particulate species is essential for a complete understanding of the possible causes of health effects associated with exposure to fine particles. Past organic compound diffusion denuder samplers developed by the authors (e.g., the Brigham Young University Organic Sampling System [BOSS]) are not amenable to routine field use because of the need to independently determine the gas-phase semi-volatile organic material efficiency of the denuder for each sample. This problem has been eliminated using a combined virtual impactor, particle-concentrator inlet to provide a concentrated stream of 0.1-2.5-μm particles. This is followed by a BOSS diffusion denuder and filter packs to collect particles, including any semi-volatile species lost from the particles during sampling. The samp ler (Particle Concentrator-Brigham Young University Organic Sampling System [PC-BOSS]) contains a post-denuder multifilter pack unit to allow for the routine collection of several sequential samples. The PC-BOSS can be used for the determination of both fine particulate nitrate and semi-volatile organic material without significant “positive” or “negative” sampling artifacts. Validation of the sampler for the determination of PM_2.5 sulfate and nitrate based on comparison of results obtained at Riverside, CA with collocated PC-BOSS, annular denuder, and Chem Spec samplers indicates the PC-BOSS gives accurate results for these species with a precision of ±5-8%. An average of 33% of the PM_2.5 nitrate was lost from the particles during sampling for both denuder and single filter samplers.     

Uptake of nitrous acid and nitrogen oxides by nylon surfaces: Implications for nitric acid measurement

The interference in HNO₃ determination due to HNO₂ and NO_x retention on nylon filters has been evaluated in laboratory and field conditions. Nitrous acid is retained on nylon filters with efficiencies varying from 25% at 12ℓ min⁻¹ to 80% at 2ℓ min⁻¹, yielding NO₂⁻ ion. In ambient sampling performed during photochemical smog episodes, NO₂⁻ is oxidized to NO₃⁻ with conversion factors up to 100%, resulting in a positive bias in HNO₃ determination.NO₂ reacts heterogeneously with H₂O on nylon surfaces according to the reaction 2NO₂ + H₂O → HNO₂ + HNO₃ with a removal constant of about 1 × 10⁻⁴ ms⁻¹ at a H₂O concentration of 20,000 ppm. The resulting nitrite and nitrate are independent of the sampling flow rate, while NO₂ concentration, sampling time and exposed nylon surface area play a directly proportional role. Accordingly, the relative interference of NO₂ with respect to HNO₃ determination is almost negligible for nylon filters, usually run at relatively high flow rates, while it may be significant for nylon denuders, which are characterized by larger exposed surfaces and lower operating flow rates.     

Evaluation of the filter pack for long-duration sampling of ambient air

A 14-week filter pack (FP) sampler evaluation field study was conducted at a site near Bondville, IL to investigate the impact of weekly sampling duration. Simultaneous samples were collected using collocated filter packs (FP) from two independent air quality monitoring networks (CASTNet and Acid-MODES) and using duplicate annular denuder systems (ADS). Precision estimates for most of the measured species are similar for weekly ADS and composited FPs. There is generally good agreement between the weekly CASTNet FP results aggregated from weekly daytime and weekly nighttime samples and those aggregated from daily 24 h Acid-MODES samples; although SO₂ is the exception, and CASTNet concentrations are higher than Acid-MODES. Comparison of weekly ADS results with composited weekly FP results from CASTNet shows good agreement for SO^2-₄. With the exception of the two weeks where the FP exceeded the ADS, both HNO₃ and the sum of particulate and gaseous NO^-₃ show good agreement. The FP often provides good estimates of HNO₃, but when used to sample atmospheres that have experienced substantial photochemical reactivity, FP HNO₃ determinations using nylon filters may be biased high. It is suggested that HNO₂ or some other oxidized nitrogen compound can accumulate on a regional scale and may interfere with the FP determination of HNO₃. FP particulate NO^-₃ results are in fair agreement with the ADS. Since FP SO₂ results are biased low by 12–20%, SO₂ concentration in the CASTNet data archive should be adjusted upward. Nylon presents problems as a sampling medium in terms of SO₂ recovery and specificity for HNO₃. Additional comparative sampler evaluation studies are recommended at several sites over each season to permit comprehensive assessment of the concentrations of atmospheric trace constituents archived by CASTNet.     

Comparison of the Annular Denuder System and the Transition Flow Reactor for Measurements of Selected Dry Deposition Species

An intensive field study was conducted in Research Triangle Park, North Carolina in the fall of 1986. Ambient concentrations of the following constituents were obtained: nitric acid, nitrous acid, nitrogen dioxide, sulfur dioxide, ammonia, hydrogen ion, and particulate nitrate, sulfate, and ammonium. Results collected using the annular denuder system (ADS) and the transition flow reactor (TFR) are presented and compared.

Both types of samplers had operational detection limits on daily (22-hour) samples that were generally below 1 μg m_-3 suggesting that both samplers can provide sensitive measurements for most of the constituents of interest. Both the ADS and TFR show reasonable (>25 percent) within-sampler precision for most of the measured species concentrations, except TFR fine particulate nitrate measurements where results were frequently negative (The TFR fine particulate nitrate measurement is calculated using subtraction of positive numbers).

Comparison of ADS and TFR daily results showed good agreement for total particulate sulfate, the sum of total (coarse plus fine) particulate and gaseous nitrate, and ammonia. As a result of different inlet particle collection efficiencies, the ADS fine particulate sulfate exceeded the TFR (5 percent). In the absence of a filter to collect volatilized particulate ammonium in the ADS, the sum of total particulate and gaseous ammonium in the TFR exceeded that in the ADS. Of potentially more importance, ADS measurements of SO₂ and H⁺ exceeded those of the TFR, while TFR measurements of HNO₃ exceeded those of the ADS. Results of this study suggest that the TFR may provide biased measurements of SO₂, H⁺, HNO₃, and Fine NO₃ ^- that cannot be corrected without modifications to the fundamental design of the sampling system.     

Simultaneous Sampling of Gas- and Aerosol-Phase TDI with a Triple Filter System

Abstract

A new triple filter system sampler/model is proposed for the precise and accurate simultaneous sampling and determination of gas- and aerosol-phase 2,4-toluene diisocyanate (TDI). The system consists of two front Teflon filters for sampling aerosol-phase TDI and a final coated glass fiber filter to collect gas-phase TDI. The aerosol-phase TDI is collected on the first Teflon filter, while the second Teflon filter is used to estimate gaseous TDI adsorbed by the first. According to the gas adsorption test of two Teflon filters in series, the TDI gas adsorption fraction of the two filters is almost the same. Results of the evaporation test using pure TDI aerosols collected on the Teflon filter show that significant evaporation of the compound does not occur during sampling. These two findings allow the use of a model to estimate accurate gasand aerosol-phase TDI concentrations. The comparison test with an annular denuder shows that the triple filter system can minimize the TDI sampling bias between the dual filter and the annular denuder systems.     

The performance of a gas and aerosol monitoring system (GAMS) for the determination of acidic water soluble organic and inorganic gases and ammonia as well as related particles from the atmosphere

A new application of the quasi-simultaneous gas/particle phase sampling and analysis principle first proposed by Simon and Dasgupta (Anal. Chem. 34 (1995) 71) is described. For the first time, a gradient chromatograph is used in connection with such a sampling system to allow the simultaneous determination of major organic (formic, acetic, propionic, oxalic, malonic and succinic) and inorganic (SO₂, HNO₂, HNO₃, HCl and H₂F₂) acidic gases and related particles. Another addition to the previous systems is the analysis of cations other than ammonium from the particulate phase. The time resolution of the instrument still remains high, 1 h, during which gaseous water-soluble acidic compounds, ammonia, as well as related anionic particles and inorganic major cations are analysed. Sampling is based on diffusion in a wetted parallel plate denuder for gases and on growth in supersaturated water vapour for particles. The determination limits range from 2 ppt (acetate) to 0.4 ppb (ammonia) in the gas phase and 0.01 μg m⁻³ (citric acid) to 0.79 μg m⁻³ (calcium) for particulate matter. Collection efficiencies for gas and aerosol sampling were quantified and the supersaturation in the aerosol sampling apparatus investigated. The system has been used for field measurements at a background station; selected results of these measurements are presented.     

Fine Particulate Organic Material in the Los Angeles Basin - I: Assessment of the High-Volume Brigham Young University Organic Sampling System,BIG BOSS

ABSTRACT

A multi-system, high-volume, parallel plate diffusion dénuder Brigham Young University Organic Sampling System (BIG BOSS) was tested using collocated samplers at the Pico Rivera Monitoring Station of the South Coast Air Quality Management District, South Coast Air Basin, in September 1994. Six-hr daytime and 9-hr nighttime samples were collected with a flow of about 200 L/min through each of the three systems designed to collect particles smaller than 2.5, 0.8, and 0.4 mm in a diffusion denuder sampler. Efficiency for the removal of gas phase organic compounds by the diffusion denuder was evaluated using both theoretical predictions and field measurements. Both measured and calculated data indicate high denuder efficiency for the removal of gas phase aromatic and paraffinic compounds. The precision of the BIG BOSS was evaluated using collocated samplers. The precision of determination of total carbon and elemental carbon retained by a quartz filter or of semi-volatile carbonaceous material lost from particles during sampling averaged ±7%. The precision of determination of individual organic compounds averaged ±10%. An average of 42 and 62% of the particulate organic material was semi-volatile organic compounds (SVOCs) lost from particles during sampling for daytime and nighttime samples, respectively. This “negative” sampling artifact was an order of magnitude larger than the “positive” quartz filter artifact due to adsorption of gas phase organic material. Daytime concentrations of fine particulate elemental carbon and nonvolatile organic carbon were higher than nighttime concentrations, but nighttime fine particles contained more semi-volatile organic material than daytime.     

Development and Evaluation of an Impactor for a PM2.5 Speciation Sampler

ABSTRACT

A conventional impactor for a particle speciation sampler was developed and validated through laboratory and field tests. The speciation sampler consists of the following components: a PM_2.5 conventional impactor that removes particles larger than 2.5 μm, an all-glass, coated honeycomb diffusion denuder, and a 47-mm filter pack. The speciation sampler can operate at two different sampling rates: 10 and 16.7 L/min. An experimental characterization of the impactor’s performance was conducted. The impactor’s collection efficiency was examined as a function of critical design parameters such as Reynolds number, the distance from the nozzle exit to the impac-tion plate, and the impaction substrate coating method. The bounce of particles larger than the cut point was successfully minimized by using a greased surface as the im-paction substrate. Additionally, a series of field intercomparison experiments were conducted at both 10 and 16.7 L/min airflow. PM_2.5 mass and SO₄ ^2- concentrations were measured and compared with the Federal Reference Method (FRM) and found to be in good agreement. Results of the laboratory chamber tests also indicated that the impactor’s performance was in good agreement with the FRM.     

Precision and Accuracy in the Determination of Sulfur Oxides,Fluoride, and Spherical Aluminosilicate Fly Ash Particles in Project MOHAVE

The precision and accuracy of the determination of particu-late sulfate and fluoride, and gas phase SO₂ and HF are estimated from the results obtained from collocated replicate samples and from collocated comparison samples for high-and low-volume filter pack and annular diffusion denuder samplers. The results of replicate analysis of collocated samples and replicate analyses of a given sample for the determination of spherical aluminosilicate fly ash particles have also been compared. Each of these species is being used in the chemical mass balance source apportionment of sulfur oxides in the Grand Canyon region as part of Project MOHAVE, and the precision and accuracy analyses given in this paper provide input to that analysis. The precision of the various measurements reported here is ±1.8 nmol/m³ and ±2.5 nmol/m³ for the determination of SO₂ and sulfate, respectively, with an annular denuder. The precision is ±0.5 nmol/m³ and ±2.0 nmol/m³ for the determination of the same species with a high-volume or low-volume filter pack. The precision for the determination of the sum of HF(g) and fine particulate fluoride is ±0.3 nmol/m³. The precision for the determination of aluminosilicate fly ash particles is ±100 particles/m³. At high concentrations of the various species, reproducibility of the various measurements is ±10% to ±14% of the measured concentration. The concentrations of sulfate determined using filter pack samplers are frequently higher than those determined using diffusion denuder sampling systems. The magnitude of the difference (e.g., 2-10 nmol sulfate/m³) is small, but important relative to the precision of the data and the concentrations of particulate sul-fate present (typically 5-20 nmol sulfate/m³). The concentrations of SO₂(g) determined using a high-volume cascade impactor filter pack sampler are correspondingly lower than those obtained with diffusion denuder samplers. The concentrations of SO_x (SO₂(g) plus particulate sulfate) determined using the two samplers during Project MOHAVE at the Spirit Mountain, NV, and Hopi Point, AZ, sampling sites were in agreement. However, for samples collected at Painted Desert, AZ, and Meadview, AZ, the concentrations of SO_x and SO₂(g) determined with a high-volume cascade impactor filter pack sampler were frequently lower than those determined using a diffusion denuder sampling system. These two sites had very low ambient relative humidity, an average of 25%. Possible causes of observed differences in the SO₂(g) and sulfate results obtained from different types of samplers are given.     

Measurements of nitrogen dioxide on Funen using diffusion tubes

Monitoring of nitrogen dioxide (NO₂) by passive sampling on the Danish island Funen (Fyn) show that the concentration of nitrogen dioxide is low (2–20 ppb). The level of NO₂ in rural and suburban areas is governed by imported airpollution, and elevated NO₂ concentrations due to local traffic are of limited importance. These results are supported by diffusion denuder measurements of nitric acid (HNO₃) and particulate nitrate. Measurements of NO₂ with chemiluminescence and diffusive passive sampling showed good agreement between the methods. The special mounting device for the diffusive samplers used in this work seem to have reduced the turbulence at the open end of the tube. The product from the reaction between nitrogen dioxide and triethanolamine was investigated and tentatively identified as triethanolamine N-oxide, which is in accordance with the observed 1 : 1 stoechiometry in the conversion of NO₂ to nitrite ions.