VOC composition and ozone-forming potential of the exhaust gas of in-use motorcycles

The emission profile of volatile organic compounds (VOC) and the ozone-forming potential (OP) of the exhaust gas of six in-use motorcycles (four 4-stroke- and two 2-stroke-engines) were determined. The motorcycles were tested on a chassis dynamometer in a real-world driving cycle. The analysis involved the C2–C12-hydrocarbons as well as the aldehydes and ketones. Additionally, the regulated THC and NO_x emissions were measured according to the test procedure for type approval (ECE 40). Two vehicles did not fulfil the THC emission standard, whereas all vehicles met the requirements for NO_x emission. The aromatic fuel components toluene and xylene, and the combustion products ethene and propene contributed most to the OP of the VOC emission. The highest OP was found with the 2-stroke engines. The VOC profile of the emissions varied with vehicle and driving conditions. The reactivity of the exhaust gas, defined as gram ozone per gram of non-methane organic gases (NMOG), increased with vehicle speed.     

Influence of Oxygenated Fuels on the Emissions from Three Pre-1985 Light-Duty Passenger Vehicles

Tailpipe and evaporative emissions from three pre-1985 passenger motor vehicles operating on an oxygenated blend fuel and on a nonoxygenated base fuel were characterized. Emission data were collected for vehicles operating over the Federal Test Procedure at 40,75, and 90°F to simulate ambient driving conditions. The two fuels tested were a commercial summer grade regular gasoline (the nonoxygenated base fuel) and an oxygenated fuel containing 9.5 percent methyl tert-butyl ether (MTBE), more olefins, and fewer aromatics than the base fuel. The emissions measured were total hydrocarbons (THCs), speciated hydrocarbons, speciated aldehydes, carbon monoxide (CO), oxides of nitrogen (NO_x), benzene, and 1,3-butadiene.

This study showed no pattern of tailpipe regulated emission reduction when oxygenated fuel was used. Tailpipe emissions from the 1984 Buick Century without a catalyst and the 1977 Mustang with catalyst decreased with the MTBE fuel. However, emissions from the 1984 Buick Century and the 1980 Chevrolet Citation, both fitted with catalysts increased. The vehicles emitted more 1,3- butadiene and, in general, more NO_x when operated with the base fuel.

THC, CO, benzene, and 1,3-butadiene emissions from both fuels and all vehicles, in general, decreased with increasing test temperature, whereas NO_x emissions, in general, increased with increasing test temperature. Formaldehyde, acetaldehyde, and total aldehydes also showed a decrease in emissions as test temperature increased. More formaldehyde was emitted when the MTBE fuel was used.

Evaporative, diurnal, and hot soak emissions from the base fuel were greater than those from the MTBE fuel. The evaporated emissions from both fuels increased with increasing test temperatures. Diurnal data indicate that canister conditioning (bringing the evaporative charcoal canister to equilibrium) is required before testing.     

Airshed Model Evaluation of Reactivity Adjustment Factors Calculated with the Maximum Incremental Reactivity Scale for Transitional-Low Emission Vehicles

Abstract

The California Air Resources Board recently adopted regulations for light- and medium-duty vehicles that require reductions in the ozone-forming potential or “reactivity,” rather than the mass, of nonmethane organic gas (NMOG) emissions. The regulations allow sale of all alternatively fueled vehicles (AFVs) that meet NMOG exhaust emission standards equivalent in reactivity to those set for vehicles fueled with conventional gasoline. Reactivity adjustment factors (RAFs), the ratio of the reactivity (per gram) of the AFV exhaust to that of the conventionally fueled vehicle (CFV), are used to correct the stringent exhaust emission standards. Complete chemical speciation of the exhaust and conversion of each NMOG species to an appropriate mass of ozone using the maximum incremental reactivity (MIR) scale of Carter determines the RAF. The MIR approach defines reactivity where NMOG control is the most effective strategy in reducing ozone concentrations, and assumes it is not important to define reactivity at other conditions, i.e., where NO_x is the limiting precursor.

This study used the Carnegie/California Institute of Technology airshed model to evaluate whether the RAF-adjusted AFV emissions result in ozone impacts equivalent to those of CFV emissions. A matrix of two ozone episodes in the South Coast Air Basin (SoCAB) of California, two base emission inventories, and exhaust emissions from three alternative fuels that meet the first level of the low emission vehicle standards bounds the expected range of conditions. Although very good agreement was found previously for individual NMOG species,² this study noted deviations of up to ±15 percent from the equal ozone impacts for any vehicle/fuel combination required by the California regulations. These deviations appear to be attributable to differences in spatial and temporal patterns of emissions between vehicle fleets, rather than a problem with the MIR approach. The first formally adopted RAF, a value of 0.41 for 85 percent methanol/15 percent gasoline-fueled vehicles, includes a 10 percent increase based on the airshed modeling. The correction to the RAF is different for other fuels and may be different for air basins other than the SoCAB.     

Multispecies remote sensing measurements of vehicle emissions on Sherman Way in Van Nuys,California

As part of the 2010 Van Nuys tunnel study, researchers from the University of Denver measured on-road fuel-specific light-duty vehicle emissions from nearly 13,000 vehicles on Sherman Way (0.4 miles west of the tunnel) in Van Nuys, California, with its multispecies Fuel Efficiency Automobile Test (FEAT) remote sensor a week ahead of the tunnel measurements. The remote sensing mean gram per kilogram carbon monoxide (CO), hydrocarbon (HC), and oxide of nitrogen (NO_x) measurements are 8.9% lower, 41% higher, and 24% higher than the tunnel measurements, respectively. The remote sensing CO/NO_x and HC/NO_x mass ratios are 28% lower and 20% higher than the comparable tunnel ratios. Comparisons with the historical tunnel measurements show large reductions in CO, HC, and NO_x over the past 23 yr, but little change in the HC/NO_x mass ratio since 1995. The fleet CO and HC emissions are increasingly dominated by a few gross emitters, with more than a third of the total emissions being contributed by less than 1% of the fleet. An example of this is a 1995 vehicle measured three times with an average HC emission of 419 g/kg fuel (two-stroke snowmobiles average 475 g/kg fuel), responsible for 4% of the total HC emissions. The 2008 economic downturn dramatically reduced the number of new vehicles entering the fleet, leading to an age increase (>1 model year) of the Sherman Way fleet that has increased the fleet's ammonia (NH₃) emissions. The mean NH₃ levels appear little changed from previous measurements collected in the Van Nuys tunnel in 1993. Comparisons between weekday and weekend data show few fleet differences, although the fraction of light-duty diesel vehicles decreased from the weekday (1.7%) to Saturday (1.2%) and Sunday (0.6%).

Implications: On-road remote sensing emission measurements of light-duty vehicles on Sherman Way in Van Nuys, California, show large historical emission reductions for CO and HC emissions despite an older fleet arising from the 2008 economic downturn. Fleet CO and HC emissions are increasingly dominated by a few gross emitters, with a single 1995 vehicle measured being responsible for 4% of the entire fleet's HC emissions. Finding and repairing and/or scrapping as little as 2% of the fleet would reduce on-road tailpipe emissions by as much as 50%. Ammonia emissions have locally increased with the increasing fleet age.     

Comparison of the MOVES2010a,MOBILE6.2, and EMFAC2007 mobile source emission models with on-road traffic tunnel and remote sensing measurements

The Desert Research Institute conducted an on-road mobile source emission study at a traffic tunnel in Van Nuys, California, in August 2010 to measure fleet-averaged, fuel-based emission factors. The study also included remote sensing device (RSD) measurements by the University of Denver of 13,000 vehicles near the tunnel. The tunnel and RSD fleet-averaged emission factors were compared in blind fashion with the corresponding modeled factors calculated by ENVIRON International Corporation using U.S. Environmental Protection Agency's (EPA's) MOVES2010a (Motor Vehicle Emissions Simulator) and MOBILE6.2 mobile source emission models, and California Air Resources Board's (CARB's) EMFAC2007 (EMission FACtors) emission model. With some exceptions, the fleet-averaged tunnel, RSD, and modeled carbon monoxide (CO) and oxide of nitrogen (NO_x) emission factors were in reasonable agreement (±25%). The nonmethane hydrocarbon (NMHC) emission factors (specifically the running evaporative emissions) predicted by MOVES were insensitive to ambient temperature as compared with the tunnel measurements and the MOBILE- and EMFAC-predicted emission factors, resulting in underestimation of the measured NMHC/NO_x ratios at higher ambient temperatures. Although predicted NMHC/NO_x ratios are in good agreement with the measured ratios during cooler sampling periods, the measured NMHC/NO_x ratios are 3.1, 1.7, and 1.4 times higher than those predicted by the MOVES, MOBILE, and EMFAC models, respectively, during high-temperature periods. Although the MOVES NO_x emission factors were generally higher than the measured factors, most differences were not significant considering the variations in the modeled factors using alternative vehicle operating cycles to represent the driving conditions in the tunnel. The three models predicted large differences in NO_x and particle emissions and in the relative contributions of diesel and gasoline vehicles to total NO_x and particulate carbon (TC) emissions in the tunnel.

Implications: Although advances have been made to mobile source emission models over the past two decades, the evidence that mobile source emissions of carbon monoxide and hydrocarbons in urban areas were underestimated by as much as a factor of 2–3 in past inventories underscores the need for on-going verification of emission inventories. Results suggest that there is an overall increase in motor vehicle NMHC emissions on hot days that is not fully accounted for by the emission models. Hot temperatures and concomitant higher ratios of NMHC emissions relative to NO_x both contribute to more rapid and efficient formation of ozone. Also, the ability of EPA's MOVES model to simulate varying vehicle operating modes places increased importance on the choice of operating modes to evaluate project-level emissions.     

Investigating the real-world emission characteristics of light-duty gasoline vehicles and their relationship to local socioeconomic conditions in three communities in Los Angeles,California

This paper discusses results from a vehicular emissions research study of over 350 vehicles conducted in three communities in Los Angeles, CA, in 2010 using vehicle chase measurements. The study explores the real-world emission behavior of light-duty gasoline vehicles, characterizes real-world super-emitters in the different regions, and investigates the relationship of on-road vehicle emissions with the socioeconomic status (SES) of the region. The study found that in comparison to a 2007 earlier study in a neighboring community, vehicle emissions for all measured pollutants had experienced a significant reduction over the years, with oxides of nitrogen (NO_X) and black carbon (BC) emissions showing the largest reductions. Mean emission factors of the sampled vehicles in low-SES communities were roughly 2–3 times higher for NO_X, BC, carbon monoxide, and ultrafine particles, and 4–11 times greater for fine particulate matter (PM_2.5) than for vehicles in the high-SES neighborhood. Further analysis indicated that the emission factors of vehicles within a technology group were also higher in low-SES communities compared to similar vehicles in the high-SES community, suggesting that vehicle age alone did not explain the higher vehicular emission in low-SES communities.

Evaluation of the emission factor distribution found that emissions from 12% of the sampled vehicles were greater than five times the mean from all of the sampled fleet, and these vehicles were consequently categorized as “real-world super-emitters.” Low-SES communities had approximately twice as many super-emitters for most of the pollutants as compared to the high-SES community. Vehicle emissions calculated using model-year-specific average fuel consumption assumptions suggested that approximately 5% of the sampled vehicles accounted for nearly half of the total CO, PM_2.5, and UFP emissions, and 15% of the vehicles were responsible for more than half of the total NO_X and BC emissions from the vehicles sampled during the study.

Implications: This study evaluated the real-world emission behavior and super-emitter distribution of light-duty gasoline vehicles in California, and investigated the relationship of on-road vehicle emissions with local socioeconomic conditions. The study observed a significant reduction in vehicle emissions for all measured pollutants when compared to an earlier study in Wilmington, CA, and found a higher prevalence of high-emitting vehicles in low-socioeconomic-status communities. As overall fleet emissions decrease from stringent vehicle emission regulations, a small fraction of the fleet may contribute to a disproportionate share of the overall on-road vehicle emissions. Therefore, this work will have important implications for improving air quality and public health, especially in low-SES communities.     

Real-world fuel use and gaseous emission rates for flex fuel vehicles operated on E85 versus gasoline

Flex fuel vehicles (FFVs) typically operate on gasoline or E85, an 85%/15% volume blend of ethanol and gasoline. Differences in FFV fuel use and tailpipe emission rates are quantified for E85 versus gasoline based on real-world measurements of five FFVs with a portable emissions measurement system (PEMS), supplemented chassis dynamometer data, and estimates from the Motor Vehicle Emission Simulator (MOVES) model. Because of inter-vehicle variability, an individual FFV may have higher nitrogen oxide (NO_x) or carbon monoxide (CO) emission rates on E85 versus gasoline, even though average rates are lower. Based on PEMS data, the comparison of tailpipe emission rates for E85 versus gasoline is sensitive to vehicle-specific power (VSP). For example, although CO emission rates are lower for all VSP modes, they are proportionally lowest at higher VSP. Driving cycles with high power demand are more advantageous with respect to CO emissions, but less advantageous for NO_x. Chassis dynamometer data are available for 121 FFVs at 50,000 useful life miles. Based on the dynamometer data, the average difference in tailpipe emissions for E85 versus gasoline is ?23% for NO_x, ?30% for CO, and no significant difference for hydrocarbons (HC). To account for both the fuel cycle and tailpipe emissions from the vehicle, a life cycle inventory was conducted. Although tailpipe NO_x emissions are lower for E85 versus gasoline for FFVs and thus benefit areas where the vehicles operate, the life cycle NO_x emissions are higher because the NO_x emissions generated during fuel production are higher. The fuel production emissions take place typically in rural areas. Although there are not significant differences in the total HC emissions, there are differences in HC speciation. The net effect of lower tailpipe NO_x emissions and differences in HC speciation on ozone formation should be further evaluated.

Implications: Reported comparisons of flex fuel vehicle (FFV) tailpipe emission rates for E85 versus gasoline have been inconsistent. To date, this is the most comprehensive evaluation of available and new data. The large range of inter-vehicle variability illustrates why prior studies based on small sample sizes led to apparently contradictory findings. E85 leads to significant reductions in tailpipe nitrogen oxide (NO_x) and carbon monoxide (CO) emission rates compared with gasoline, indicating a potential benefit for ozone air quality management in NO_x-limited areas. The comparison of FFV tailpipe emissions between E85 and gasoline is sensitive to power demand and driving cycles.     

A Multipurpose Flare Stack for Control of Chemical Process Wastes

Abstract

To test the effectiveness of California’s vehicle inspection/ maintenance (I/M) program, exclusive of vehicle-owner intervention, a fleet of more than 1,100 vehicles that previously had failed California’s Smog Check test were sent to randomly selected Smog Check stations in the Los Angeles area for covert inspections and repairs. The two-speed idle test was used for repairs. For those vehicles that were repaired at the first inspection, their FTP emission reductions were 25%, 14%, and 11% for hydrocarbons (HC), carbon monoxide (CO), and nitrogen oxides (NO_x), respectively, although emissions testing for NO_x was not performed at the Smog Check stations. Idle HC and CO emissions increased for 35% and 43% of the vehicles, respectively, after repairs. This data set shows that most vehicles that fail the Smog Check inspection are only marginal emitters, with 61% and 44% of the total potential for HC and CO emission reductions, respectively, coming from only 10% of the vehicles that currently fail the inspection. When the vehicles were rank-ordered by idle emissions from dirtiest to cleanest, emission reduction costs for the highest-emitting 10% of the fleet averaged $l,100/ton and $250/ton for HC and CO, respectively, attributing all the costs to each pollutant exclusively. For the remaining vehicles, costs increased dramatically.     

Study of Miller timing on exhaust emissions of a hydrotreated vegetable oil (HVO)-fueled diesel engine

The effect of intake valve closure (IVC) timing by utilizing Miller cycle and start of injection (SOI) on particulate matter (PM), particle number, and nitrogen oxide (NO_x) emissions was studied with a hydrotreated vegetable oil (HVO)-fueled nonroad diesel engine. HVO-fueled engine emissions, including aldehyde and polyaromatic hydrocarbon (PAH) emissions, were also compared with those emitted with fossil EN590 diesel fuel. At the engine standard settings, particle number and NO_x emissions decreased at all the studied load points (50%, 75%, and 100%) when the fuel was changed from EN590 to HVO. Adjusting IVC timing enabled a substantial decrease in NO_x emission and combined with SOI timing adjustment somewhat smaller decrease in both NO_x and particle emissions at IVC??50 and??70 °CA points. The HVO fuel decreased PAH emissions mainly due to the absence of aromatics. Aldehyde emissions were lower with the HVO fuel with medium (50%) load. At higher loads (75% and 100%), aldehyde emissions were slightly higher with the HVO fuel. However, the aldehyde emission levels were quite low, so no clear conclusions on the effect of fuel can be made. Overall, the study indicates that paraffinic HVO fuels are suitable for emission reduction with valve and injection timing adjustment and thus provide possibilities for engine manufacturers to meet the strictening emission limits.

Implications: NO_x and particle emissions are dominant emissions of diesel engines and vehicles. New, biobased paraffinic fuels and modern engine technologies have been reported to lower both of these emissions. In this study, even further reductions were achieved with engine valve adjustment combined with novel hydrotreated vegetable oil (HVO) diesel fuel. This study shows that new paraffinic fuels offer further possibilities to reduce engine exhaust emissions to meet the future emission limits.

Supplementary Materials: Supplementary materials are available for this paper. Go to the publisher's online edition of the Journal of the Air & Waste Management Association for a complete list of analysed PAH compounds.     

On-Road,In-Use Gaseous Emission Measurements by Remote Sensing of School Buses Equipped with Diesel Oxidation Catalysts and Diesel Particulate Filters

Abstract

A remote sensing device was used to obtain on-road and in-use gaseous emission measurements from three fleets of schools buses at two locations in Washington State. This paper reports each fleet’s carbon monoxide (CO), hydrocarbon (HC), nitric oxide (NO), and nitrogen dioxide (NO₂) mean data. The fleets represent current emission retrofit technologies, such as diesel particulate filters and diesel oxidation catalysts, and a control fleet. This study shows that CO and HC emissions decrease with the use of either retrofit technology when compared with control buses of the same initial emission standards. The CO and HC emission reductions are consistent with published U.S. Environmental Protection Agency verified values. The total oxides of nitrogen (NO_x), NO, and the NO₂/NO_x ratio all increase with each retrofit technology when compared with control buses. As was expected, the diesel particulate filters emitted significantly higher levels of NO₂ than the control fleet because of the intentional conversion of NO to NO₂ by these systems. Most prior research suggests that NO_x emissions are unaffected by the retrofits; however, these previous studies have not included measurements from retrofit devices on-road and after nearly 5 yr of use. Two 2006 model-year buses were also measured. These vehicles did not have retrofit devices but were built to more stringent new engine standards. Reductions in HCs and NO_x were observed for these 2006 vehicles in comparison to other non-retrofit earlier model-year vehicles.     

On-road remote sensing measurements and fuel-based motor vehicle emission inventory in Hangzhou,China

Motor vehicles are one of the largest sources of air pollutants worldwide. Despite their importance, motor vehicle emissions are inadequately understood and quantified, esp. in developing countries. In this study, the real-world emissions of carbon monoxide (CO), hydrocarbons (HC) and nitrogen oxide (NO) were measured using an on-road remote sensing system at five sites in Hangzhou, China in 2004 and 2005. Average emission factors of CO, HC and NO_x for petrol vehicles of different model year, technology class and vehicle type were calculated in grams of pollutant per unit of fuel use (g l⁻¹) from approximately 32,260 petrol vehicles. Because the availability of data used in traditional on-road mobile source estimation methodologies is limited in China, fuel-based approach was implemented to estimate motor vehicle emissions using fuel sales as a measure of vehicle activity, and exhaust emissions factors from remote sensing measurements. The fuel-based exhaust emission inventories were also compared with the results from the recent international vehicle emission (IVE) model. Results show that petrol vehicle fleet in Hangzhou has significantly high CO emissions, relatively high HC and low NO_x, with the average emission factors of 193.07±15.63, 9.51±2.40 and 5.53±0.48 g l⁻¹, respectively. For year 2005 petrol vehicles exhaust emissions contributed with 182,013±16,936, 9107±2255 and 5050±480 metric ton yr⁻¹ of CO, HC and NO_x, respectively. The inventories are 45.5% higher, 6.6% higher and 53.7% lower for CO, HC and NO_x, respectively, than the estimates using IVE travel-based model. In addition, a number of insights about the emission distributions and formation mechanisms have been obtained from an in-depth analysis of these results.     

The Effect of Reformulated Gasoline on Ambient Carbon Monoxide Concentrations in Southeastern Wisconsin

Abstract

Reformulated gasoline (RFG) contains oxygen additives such as methyl tertiary butyl ether or ethanol. The additives enable vehicles to burn fuel with a higher air/fuel ratio, thereby lowering the emission of carbon monoxide (CO) and volatile organic compounds (VOCs). Because VOCs react with sunlight to form ozone (O₃), the Clean Air Act requires severe O₃ nonattainment areas such as southeastern Wisconsin to use RFG. On July 17, 2001, the U.S. Environmental Protection Agency (EPA) granted Milwaukee, WI, and Chicago, IL, a waiver from the VOC reduction requirement of Phase II RFG. The VOC reduction requirement was lowered from 27.4% of the 1990 baseline fuel to 25.4%. The assumption was that ethanol-blended RFG would lower summertime CO concentrations sufficiently to offset the increased VOC emissions. The waiver is estimated to increase VOC emissions by ～0.8%, or 0.4 t of VOC on a hot summer weekday. This study evaluates whether RFG has been effective in lowering southeastern Wisconsin ambient CO concentrations. Three years of ambient CO data before RFG was introduced were compared with the first three years of ambient CO data after RFG was introduced. This paper also evaluates how the meteorology, vehicle inspection/maintenance program, vehicle miles traveled, and stationary source emissions influence CO concentrations. The winter decrease in ambient CO concentrations was found to be statistically significant, while the summer data showed no statistically significant change, indicating that RFG is most effective lowering ambient CO concentrations in cold weather.     

Deriving fuel-based emission factor thresholds to interpret heavy-duty vehicle roadside plume measurements

Remote sensing devices have been used for decades to measure gaseous emissions from individual vehicles at the roadside. Systems have also been developed that entrain diluted exhaust and can also measure particulate matter (PM) emissions. In 2015, the California Air Resources Board (CARB) reported that 8% of in-field diesel particulate filters (DPF) on heavy-duty (HD) vehicles were malfunctioning and emitted about 70% of total diesel PM emissions from the DPF-equipped fleet. A new high-emitter problem in the heavy-duty vehicle fleet had emerged. Roadside exhaust plume measurements reflect a snapshot of real-world operation, typically lasting several seconds. In order to relate roadside plume measurements to laboratory emission tests, we analyzed carbon dioxide (CO₂), oxides of nitrogen (NO_X), and PM emissions collected from four HD vehicles during several driving cycles on a chassis dynamometer. We examined the fuel-based emission factors corresponding to possible exceedances of emission standards as a function of vehicle power. Our analysis suggests that a typical HD vehicle will exceed the model year (MY) 2010 emission standards (of 0.2 g NO_X/bhp-hr and 0.01 g PM/bhp-hr) by three times when fuel-based emission factors are 9.3 g NO_X/kg fuel and 0.11 g PM/kg using the roadside plume measurement approach. Reported limits correspond to 99% confidence levels, which were calculated using the detection uncertainty of emissions analyzers, accuracy of vehicle power calculations, and actual emissions variability of fixed operational parameters. The PM threshold was determined for acceleration events between 0.47 and 1.4 mph/sec only, and the NO_X threshold was derived from measurements where after-treatment temperature was above 200°C. Anticipating a growing interest in real-world driving emissions, widespread implementation of roadside exhaust plume measurements as a compliment to in-use vehicle programs may benefit from expanding this analysis to a larger sample of in-use HD vehicles.

Implications: Regulatory agencies, civil society, and the public at large have a growing interest in vehicle emission compliance in the real world. Leveraging roadside plume measurements to identify vehicles with malfunctioning emission control systems is emerging as a viable new and useful method to assess in-use performance. This work proposes fuel-based emission factor thresholds for PM and NOx that signify exceedances of emission standards on a work-specific basis by analyzing real-time emissions in the laboratory. These thresholds could be used to prescreen vehicles before roadside enforcement inspection or other inquiry, enhance and further develop emission inventories, and potentially develop new requirements for heavy-duty inspection and maintenance (I/M) programs, including but not limited to identifying vehicles for further testing.     

Speciated hydrocarbon profiles and calculated reactivities of exhaust and evaporative emissions from 82 in-use light-duty Australian vehicles

Mass emissions of non-methane hydrocarbon (NMHC) from 26 pre-1986 and 56 post-1985 catalyst-equipped in-service vehicles were determined from measurements made on a chassis dynamometer using an urban drive cycle. Evaporative emissions were measured on a subset (4 pre-1986 and 8 post-1985) of these vehicles. Average ADR emissions (mg/km) of the individual HCs from the older pre-1986 vehicles were generally 4–7 times the emissions from newer catalyst-equipped vehicles. Evaporative emissions from the older vehicles are also much higher than those of newer vehicles. Exhaust from newer catalyst-equipped vehicles had lower proportions of substituted aromatics and alkenes and higher proportions of lower molecular weight alkanes. The effect of fuel type on the exhaust emissions was also investigated by refuelling 9 of the pre-1986 vehicles with both unleaded and leaded petrol. A 20–40% reduction in HC mass emissions was observed when unleaded petrol was used instead of leaded petrol. Reactivities of the emissions and the contributions from different classes of compounds are also reported. The specific reactivity of the exhaust emissions from newer vehicles was lower than that for older vehicles owing to the smaller proportions of highly reactive alkenes and substituted aromatic species. Moreover, as older vehicles have higher average mass emissions, when considered on a per-km basis, the pre-1986 vehicles have a greater ozone-forming potential than post-1985 vehicles. The specific reactivities of the NMHC (gO₃/gNMHC) of both the heat build and hot soak evaporative emissions were much lower than the exhaust emissions.     

Long-Term Efficiency of Catalytic Converters Operating in Mexico City

ABSTRACT

A 1999 ordinance by the Government of Mexico City bans 1993 model-year vehicles from on-road operation if their catalytic converters are not replaced with new ones. To validate the benefits of this action, we examined three issues related to exhaust emissions of vehicles equipped with catalytic converters. After selecting representative fleets of in-use vehicles, a comparison between emissions and catalyst efficiency in cars with two categories of exhaust emission limits was carried out. For that purpose, two fleets were selected, each made up of 10 vehicles run under similar conditions. A third, larger fleet with emissions control systems was used to evaluate and simulate real-world conditions of vehicles in a controlled laboratory. Finally, the aging effect on the catalytic converter was studied on vehicles run for 100,000 km, replacing their old emission control devices for new ones.

The 1991-1992 model-year vehicles showed a high percentage of compliance with the corresponding emissions standard (90%) in comparison with 1993 model-year and later vehicles (Tier 0). However, NO_x emissions were higher for the newer vehicles. Fifty percent of the 1991-1992 model-year vehicles evaluated under the official inspection/maintenance (I/M) procedure did not meet the regulated emissions standard when the results were compared with those of the U.S. Federal Test Procedure     

Evaluation of combustion by-products of MTBE as a component of reformulated gasoline

Methyl tertiary-butyl ether (MTBE) is a gasoline oxygenate that is widely used throughout the US and Europe as an octane-booster and as a means of reducing automotive carbon monoxide (CO) emissions. The combustion by-products of pure MTBE have been evaluated in previous laboratory studies, but little attention has been paid to the combustion by-products of MTBE as a component of gasoline. MTBE is often used in reformulated gasoline (RFG), which has chemical and physical characteristics distinct from conventional gasoline. The formation of MTBE by-products in RFG is not well-understood, especially under "worst-case" vehicle emission scenarios such as fuel-rich operations, cold-starts or malfunctioning emission control systems, conditions which have not been studied extensively. Engine-out automotive dynamometer studies have compared RFG with MTBE to non-oxygenated RFG. Their findings suggest that adding MTBE to reformulated gasoline does not impact the high temperature flame chemistry in cylinder combustion processes. Comparison of tailpipe and exhaust emission studies indicate that reactions in the catalytic converter are quite effective in destroying most hydrocarbon MTBE by-product species. Since important reaction by-products are formed in the post-flame region, understanding changes in this region will contribute to the understanding of fuel-related changes in emissions.     

Revised estimates of construction activity and emissions: Effects on ozone and elemental carbon concentrations in southern California

Emissions from diesel-powered construction equipment are an important source of nitrogen oxides (NO_x) and particulate matter (PM). A new emission inventory for construction equipment emissions is developed based on surveys of diesel fuel use; the revised inventory is compared to current emission inventories. California's OFFROAD model estimates are 4.5 and 3.1 times greater, for NO_x and PM respectively, than the fuel-based estimates developed here. The most relevant uncertainties are the overall amount of construction activity/diesel fuel use, exhaust emission factors for PM and NO_x, and the spatial allocation of emissions to county level and finer spatial scales. Construction permit data were used in this study to estimate spatial distributions of emissions; the resulting distribution is well correlated with population growth. An air quality model was used to assess the impacts of revised emission estimates. Increases of up to 15 ppb in predicted peak ozone concentrations were found in southern California. Elemental carbon and fine particle mass concentrations were in better agreement with observations using revised emission estimates, whereas negative bias in predictions of ambient NO_x concentrations increased.     

Idle Emissions from Heavy-Duty Diesel and Natural Gas Vehicles at High Altitude

ABSTRACT

Idle emissions of total hydrocarbon (THC), CO, NO_x, and particulate matter (PM) were measured from 24 heavy-duty diesel-fueled (12 trucks and 12 buses) and 4 heavy-duty compressed natural gas (CNG)-fueled vehicles. The volatile organic fraction (VOF) of PM and aldehyde emissions were also measured for many of the diesel vehicles. Experiments were conducted at 1609 m above sea level using a full exhaust flow dilution tunnel method identical to that used for heavy-duty engine Federal Test Procedure (FTP) testing. Diesel trucks averaged 0.170 g/min THC, 1.183 g/min CO, 1.416 g/min NO_x, and 0.030 g/min PM. Diesel buses averaged 0.137 g/min THC, 1.326 g/min CO, 2.015 g/min NO_x, and 0.048 g/min PM.

Results are compared to idle emission factors from the MOBILE5 and PART5 inventory models. The models significantly (45-75%) overestimate emissions of THC and CO in comparison with results measured from the fleet of vehicles examined in this study. Measured NO_x emissions were significantly higher (30-100%) than model predictions. For the pre-1999 (pre-consent decree) truck engines examined in this study, idle NO_x emissions increased with Health and Environment; June 30, 1999 (available from the authors).     

Emission Factors for High-Emitting Vehicles Based on On-Road Measurements of Individual Vehicle Exhaust with a Mobile Measurement Platform

ABSTRACT

Fuel-based emission factors for 143 light-duty gasoline vehicles (LDGVs) and 93 heavy-duty diesel trucks (HDDTs) were measured in Wilmington, CA using a zero-emission mobile measurement platform (MMP). The frequency distributions of emission factors of carbon monoxide (CO), nitrogen oxides (NO_x), and particle mass with aerodynamic diameter below 2.5 μm (PM_2.5) varied widely, whereas the average of the individual vehicle emission factors were comparable to those reported in previous tunnel and remote sensing studies as well as the predictions by Emission Factors (EMFAC) 2007 mobile source emission model for Los Angeles County. Variation in emissions due to different driving modes (idle, low- and high-speed acceleration, low- and high-speed cruise) was found to be relatively small in comparison to intervehicle variability and did not appear to interfere with the identification of high emitters, defined as the vehicles whose emissions were more than 5 times the fleet-average values. Using this definition, approximately 5% of the LDGVs and HDDTs measured were high emitters. Among the 143 LDGVs, the average emission factors of NO_x, black carbon (BC), PM_2.5, and ultrafine particle (UFP) would be reduced by 34%, 39%, 44%, and 31%, respectively, by removing the highest 5% of emitting vehicles, whereas CO emission factor would be reduced by 50%. The emission distributions of the 93 HDDTs measured were even more skewed: approximately half of the NO_x and CO fleet-average emission factors and more than 60% of PM_2.5, UFP, and BC fleet-average emission factors would be reduced by eliminating the highest-emitting 5% HDDTs. Furthermore, high emissions of BC, PM_2.5, and NO_x tended to cluster among the same vehicles.

IMPLICATIONS This study presents the characterization of on-road vehicle emissions in Wilmington, CA, by sampling individual vehicle plumes. Approximately 5% of the vehicles were high emitters, whose emissions were more than 5 times the fleet-average values. These high emitters were responsible for 30% and more than 50% of the average emission factors of LDGVs and HDDVs, respectively. It is likely that as the overall fleet becomes cleaner due to more stringent regulations, a small fraction of the fleet may contribute a growing and disproportionate share of the overall emissions. Therefore, long-term changes in on-road emissions need to be monitored.     

Germany

ABSTRACT

The 1988 Alternative Motor Fuels Act and the 1990 Clean Air Act Amendments require examination of the potential to favorably influence air quality by changing the composition of motor vehicle fuels. Motor vehicle tailpipe and evaporative emissions were characterized using laboratory simulations of roadway driving conditions and a variety of vehicle-fuel technologies (reformulated gasoline (RFG), methanol (M85), ethanol (E85), and natural gas (CNG)). Speciated organic compound (with Carter MIR ozone potential), CO, and NO_x emission rates and fuel economy were characterized. The Carter MIR ozone potential of combined Federal Test Procedure (FTP) tailpipe and evaporative emissions was reduced more than 90% with CNG relative to RFG, M85, and E85 fuels. FTP toxic compound emissions (benzene, formaldehyde, acetalde-hyde, and 1,3-butadiene) were greater with M85 and E85 fuels than with RFG fuel, and less with CNG fuel than RFG fuel. The most abundant toxic compound was benzene with RFG fuel, formaldehyde with M85 fuel, and acetaldehyde with E85 fuel. FTP MPG fuel economies were reduced with M85 and E85 fuels relative to RFG fuel, consistent with their lower BTU/gal. Energy efficiencies (BTU/mi) were improved with all the alternative fuels relative to RFG. Carter MIR ozone potential was generally reduced with the alternative fuels relative to RFG fuel under REP05 (high speeds and acceleration rates) driving conditions (most significantly with CNG). Toxic aldehyde emissions were reduced under REP05 conditions relative to FTP conditions with all the tested fuels, and toxic benzene emissions were elevated under high acceleration conditions.