Soot Control During the Combustion of Polystyrene

This paper describes an experimental study on the control of soot formation during the combustion of polystyrene (PS). A stable, twodimensional flame generated by using a Wolfhard-Parker type diffusion flame burner was used to simulate practical combustion situations. The combustion characteristics, effects of operating conditions on soot formation, and the effectiveness of various metallic additives as soot suppressants were investigated. It was found that soot yield could not be significantly reduced by controlling the oxidizer (air) flow rate. Increasing the O₂ mole fraction of the oxidlzer increased soot yield under typical operating conditions. However, soot yield could be greatly reduced by adding small amounts of air into the pyrolysis zone of the flame. The additional air would probably increase the combustion reaction rate while decreasing the soot precursor formation rate, thereby causing the observed effect. It was thus suggested that effective soot control could be accomplished by improving mixing between air and the PS devolatilizatlon products In practical combustion situations. The metallic additives tested in this study were the salts of Na, K, Ca, and Ba. Among these salts, Ca was the least effective in reducing soot, and K and Na were nearly equally effective. Ba was much more effective than all the others, and Its effectiveness was strongly dependent on its addition rate.     

Metal accumulation by submerged macrophytes in eutrophic lakes at the watershed scale

Metal concentrations (Al, Ba, Ca, K, Li, Mg, Na, Se, Sr and Ti) in submerged macrophytes and corresponding water and sediments were studied in 24 eutrophic lakes along the middle and lower reaches of the Yangtze River (China). Results showed that these eutrophic lakes have high metal concentrations in both water and sediments because of human activities. Average concentrations of Al and Na in tissues of submerged macrophytes were very high in sampled eutrophic lakes. By comparison, Ceratophyllum demersum and Najas marina accumulated more metals (e.g. Ba, Ca, K, Mg, Na, Sr and Ti). Strong positive correlations were found between metal concentrations in tissues of submerged macrophytes, probably because of co-accumulation of metals. The concentrations of Li, Mg, Na and Sr in tissues of submerged macrophytes significantly correlated with their corresponding water values, but not sediment values.     

Size distribution and anthropogenic sources apportionment of airborne trace metals in Kanazawa,Japan

Aerosol samples were collected from Kanazawa, Japan to examine the size distribution of 12 elements and to identify the major sources of anthropogenic elements. Key emission sources were identified and, concentrations contributed from individual sources were estimated as well. Concentrations of elements V, Ca, Cd, Fe, Ba, Mg, Mn, Pb, Sr, Zn, Co and Cu in aerosols were determined with ICP-MS. The results showed that Ca, Mg, Sr, Mn, Co and Fe were mainly associated with coarse particles (>2.1 μm), primarily from natural sources. In contrast, the elements Zn, Ba, Cd, V, Pb and Cu dominated in fine aerosol particles (<2.1 μm), implying that the anthropogenic origin is the dominant source. Results of the factor analysis on elements with high EF_Crust values (>10) showed that emissions from waste combustion in incinerators, oil combustion (involving waste oil burning and oil combustion in both incinerators and electricity generation plants), as well as coal combustion in electricity generation plants were major contributors of anthropogenic metals in the ambient atmosphere in Kanazawa. Quantitatively estimated sum of mean concentrations of anthropogenic elements from the key sources were in good agreement with the observed values. Results of this study elucidate the need for making pollution control strategy in this area.     

Survey on composition and bioconcentration potential of 12 metallic elements in King Bolete (Boletus edulis) mushroom that emerged at 11 spatially distant sites

This paper provides data on baseline concentrations, interrelationships and bioconcentration potential of 12 metallic elements by King Bolete collected from 11 spatially distant sites across Poland. There are significant differences in concentrations of metals (Al, Ba, Ca, Cd, Cu, Fe, K, Mg, Mn, Na, Sr, Zn) and their bioconcentration potential in King Bolete Boletus edulis at 11 spatially distant sites surveyed across Poland. These have resulted from significant geographical differences in trace metal concentrations in a layer (0-10 cm) of organic and mineral soil underneath to fruiting bodies and possible local bioavailabilities of macro- (Ca, K, Mg, Na) and trace metals (Al, Ba, Cd, Cu, Fe, Mn, Sr, Zn) to King Bolete. The use of highly appreciated wild-grown edible King Bolete mushroom has established a baseline measure of regional minerals status, heavy metals pollution and assessment of intake rates for wild mushroom dish fanciers against which future changes can be compared. Data on Cd, Cu and Zn from this study and from literature search can be useful to set the maximum limit of these metals in King Bolete collected from uncontaminated (background) areas. In this report also reviewed are data on Al, Ba, Ca, Cd, Cu, Fe, K, Mg, Mn, Na, Sr and Zn accumulation in King Bolete.     

Chemical content and source apportionment of 36 heavy metal analysis and health risk assessment in aerosol of Beijing

The concentration levels of 36 airborne heavy metals and atmospheric radioactivity in total suspended particulate (TSP) samples were measured to investigate the chemical characteristics, potential sources of aerosols, and health risk in Beijing, China, from September 2016 to September 2017. The TSP concentrations varied from 6.93 to 469.18 μg/m³, with a median of 133.97 μg/m³. The order for the mean concentrations of heavy metals, known as hazardous air pollutants (HAPs), was as follows: Mn > Pb > As > Cr > Ni > Se > Cd > Co > Sb > Hg > Be; Non-Designated HAPs Metals: Ca > Fe > Mg > Al > K > Na > Zn > P > Ba > Ti > Cu > Sr > B > Sn > I > V > Rb > Ce > Mo > Cs > Th > Ag > U > Pt. The median concentration of As was higher than China air quality standard (6 ng/m³). The gross α and β concentration levels in aerosols were (1.84?±?1.59) mBg/m³ and (1.15?±?0.85) mBg/m³, respectively. The enrichment factor values of Cu, Ba, B, Ce, Tl, Cs, Pb, As, Cd, Sb, Hg, Fe, Zn, Sn, I, Mo, and Ag were higher than 10, which indicated enriched results from anthropogenic sources. Pb, As, and Cd are considered to originate from multiple sources; fireworks released Ba during China spring festival; Fe, Ce, and Cs may come from stable emissions such as industrial gases. The health risks from anthropogenic metals via inhalation, ingestion, and dermal pathway were estimated on the basis of health quotient as well as the results indicated that children faced the higher risk than adults during the research period. For adults, the health risk posed by heavy metals in atmospheric particles was below the acceptable level.

     

Anthropogenic metal enrichment of snow and soil in north-eastern European Russia

Trace metal composition of winter snowpack, snow-melt filter residues and top-soil samples were determined along three transects through industrial towns in the Usa basin, North-East Russia: Inta, Usinsk and Vorkuta. Snow was analysed for Ag, Al, As, Ba, Cd, Co, Cr, Cu, Mn, Ni, Pb, Sr and Zn using ICP-MS (Ca and K by F-AAS for Vorkuta only), pH and acidity/alkalinity. Filter residues were analysed for: Al, Ba, Ca, Cd, Cu, K, Mg, Mn, Ni, Pb, Sr and Zn using F-AAS and GF-AAS; top-soil samples were analysed for Ba, Cu, Mg, Mn, Na, Ni, Pb, Sr, Zn using F-AAS. Results indicate elevated concentrations of elements associated with alkaline combustion ash around the coal mining towns of Vorkuta and Inta. There is little evidence of deposition around the gas and oil town of Usinsk. Atmospheric deposition in the vicinity of Vorkuta, and to a lesser extent Inta, added significantly to the soil contaminant loading as a result of ash fallout. Acid deposition was associated with pristine areas whereas alkaline combustion ash near to emission sources more than compensated for the acidity caused by SO2.     

The use of olive tree (<Emphasis Type="Italic">Olea europaea</Emphasis> L.) leaves as a bioindicator for environmental pollution in the Province of Aydın,Turkey

Introduction  

In this study, olive tree leaves, collected from 50 sampling sites throughout the Province of Aydın, Turkey, were used to estimate level of pollution by measuring Al, As, B, Ba, Ca, Co, Cr, Cu, Fe, K, Li, Mg, Mn, Na, Ni, Pb, Sr, and Zn concentrations and calculating pollution factor (PF) values.     

Source characterization for atmospheric trace metals over Kiel Bight

Atmospheric concentrations of Na, Al, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Rb, Sr, Ba and Pb are reported for 59 weekly air filter samples collected over the Kiel Bight. The contributions of sea salt, mineral dust and anthropogenic emissions to each of these elements were assumed to be represented by the concentrations of indicator elements, which were Na, Al and Zn, respectively. Based on this assumption a multiple regression analysis was applied to the concentration data. The results showed that atmospheric sea salt contributed significantly only to Sr and, of course, Na. Considerable portions of Al, K, Ca, Ti, Cr, Mn, Fe, Rb, Sr and Ba were derived from mineral dust. Anthropogenic sources were responsible for total V, Ni, Cu, Zn, As and Pb, and there was an anthropogenic component for most of the other elements.Moreover, the anthropogenic contribution was characterized by a nearly constant composition with respect to Ca, Ti, Cr, Mn, Fe, Cu, Zn, As, Rb, Sr, Ba and Pb, indicating that trace metals over the Kiel Bight are mainly derived from one source area. This conclusion was confirmed by correlating anthropogenic trace metal concentrations with the wind direction. A 40° wind sector directed to the south of the sampling site was identified as the major pathway for the transport of anthropogenic trace metals to the Kiel Bight.     

Multivariate analysis of mineral constituents of edible Parasol Mushroom (Macrolepiota procera) and soils beneath fruiting bodies collected from Northern Poland

Caps and stipes of 141 fruiting bodies of Parasol Mushroom (Macrolepiota procera) and surface layer of soils collected from 11 spatially distant and background (pristine) areas in Northern Poland were analyzed for Ag, Al, Ba, Ca, Cd, Co, Cr, Cu, Fe, Hg, K, Mg, Mn, Na, Ni, P, Pb, Rb, Sr, and Zn by inductively coupled plasma optical emission spectroscopy and cold vapor atomic absorption spectroscopy. In terms of bioconcentration and bioexclusion concept, K, Ag, Cu, Rb, and P were highly bioconcentrated in caps, and their bioconcentration factor values varied for the 11 sites between 120 and 500—67–420, 70–220, 10–170, and 45–100, respectively. Cd, Zn, Mg, and Na showed bioconcentration factors (BCFs) between 3.3 and 36, 3.7–15, 0.92–6.3, and 1.4–44 while Al, Ba, Ca, Co, Cr, Mn, Ni, Pb, and Sr were excluded (BCF < 1). The Parasol Mushroom is a species harvested in the wild, and its caps are of unique taste and can contain a spectrum of essential and hazardous mineral compounds accumulated at elevated concentrations, even if collected at the background (pristine) areas. These elevated mineral concentrations of the caps are due to the efficient bioconcentration potential of the species (K, Ag, Cu, Rb, P, Cd, Zn, Mg, and Na) and abundance in the soil substrates (Al, Ca, Fe, Mn). The estimated intake rates of Cd, Hg, and Pb contained in Parasol Mushroom’s caps show a cause for concern associated with these metals resulting from the consumption of between 300- and 500-g caps daily, on a frequent basis in the mushrooming season.     

Size distribution and anthropogenic sources apportionment of airborne trace metals in Kanazawa, Japan

Aerosol samples were collected from Kanazawa, Japan to examine the size distribution of 12 elements and to identify the major sources of anthropogenic elements. Key emission sources were identified and, concentrations contributed from individual sources were estimated as well. Concentrations of elements V, Ca, Cd, Fe, Ba, Mg, Mn, Pb, Sr, Zn, Co and Cu in aerosols were determined with ICP-MS. The results showed that Ca, Mg, Sr, Mn, Co and Fe were mainly associated with coarse particles (>2.1 μm), primarily from natural sources. In contrast, the elements Zn, Ba, Cd, V, Pb and Cu dominated in fine aerosol particles (<2.1 μm), implying that the anthropogenic origin is the dominant source. Results of the factor analysis on elements with high EF_Crust values (>10) showed that emissions from waste combustion in incinerators, oil combustion (involving waste oil burning and oil combustion in both incinerators and electricity generation plants), as well as coal combustion in electricity generation plants were major contributors of anthropogenic metals in the ambient atmosphere in Kanazawa. Quantitatively estimated sum of mean concentrations of anthropogenic elements from the key sources were in good agreement with the observed values. Results of this study elucidate the need for making pollution control strategy in this area.     

Leaching of metals from sewage sludge during one year and their relationship to particle size

Leaching of metals from sewage sludge can lead to their accumulation in topsoil and can also contaminate groundwater. Our objectives were to document the metal leachates and the size distribution of leached particles from sewage sludge and to identify possible correlations with physical factors. Results from monthly lysimeter sampling showed an initial release followed by decline for most metals. Cadmium, Ca, Sr, Li, Mn, Ni and Zn showed a "cyclic" behaviour. Filtration revealed that this "cyclicity" had no correlation to the size of released particles, but Al, Cr, Fe, Cu, Ag and Pb were clearly related to release of coarser particles most of the year. Total metal amounts leached during one year, relative to original sludge content, had the order Na>Ca=Mg>Mn>Sr>Zn>K>Li=Ni>Cd>Co>Rb>Ag>Cr>Ba=Cu>Ga>Al=Pb=Fe. There were no simple correlations between monthly measured leachate concentrations and precipitation, temperature or pH of precipitation. Occasional leachate sampling might give misleading values for metals with "cyclic" behaviour.     

Study on the effect of iron on PM10 formation and design of a particle-generating system using a cocentric diffusion burner flame

Iron pentacarbonyl was added to a cocentric diffusion burner flame burning a mixture of acetylene and ethylene in a co-flowing stream of air. Samples of aerosols and gaseous species were collected within the flames and above the flames with filters and a sampling bottle, and soot volume fraction through the flame was calculated with laser light extinction measurements. Aerosol was isokinetically collected in the inhalation chamber to measure particle concentration and size distribution. Laser extinction measurement showed that iron (Fe) gave an effect on soot formation process and scanning electron microscopy of the aerosol sample showed that soot particle size for the Fe-doped flame was relatively smaller than that of non-Fe-doped flame. Transmission electron microscopy results indicated that Fe species were separated from the soot at the downstream flame. Particles of the soot and Fe mixture could be generated continuously, and the concentration was kept constant under a given experimental condition using the cocentric diffusion flame burner. The mass loading variation for each target concentration (i.e., 100, 200, and 400 microg/m3) in the inhalation chamber was less than +/-5% during 10 hr. This particle-generating burner system could be used effectively for a bioassay test to evaluate risk     

Temporal variability in 20 chemical elements content of Parasol Mushroom (Macrolepiota procera) collected from two sites over a few years

Mature specimens of Parasol Mushroom were collected annually in the outskirts of the Siemiany (2000–2003) and Rafa (2001–2003) sites in the northern part of Poland to examine temporal variations and similarities in the composition of 20 chemical elements. Analysis was done under the same condition and using well-validated analytical methods. Elements were determined by inductively coupled plasma–atomic emission spectroscopy and cold vapour–atomic absorption spectroscopy (Hg). The ranges of Ag, Al, Ba, Ca, Cd, Co, Cu, Cr, Fe, Hg, K, Mg, Mn, Na, Ni, P, Pb, Rb, Sr and Zn concentrations in the caps of fruiting bodies were similar (p > 0.05; Mann-Whitney U test) for both geographically distant sites, and these specimens from Rafa were more contaminated with Pb (p < 0.05; Mann-Whitney U test). The annual collections of caps in the Siemiany site varied in Ag, Al, Ba, Ca, Cd, Co, Cu, Fe, Hg, Na, Rb and Sr and contents (0.05 < p < 0.001), while they were similar in Cr, K, Mg, Mn, Ni, P, Pb and Zn (p > 0.05; Mann-Whitney U test). The annual collections of specimens from the Rafa site varied in contents of Ag, Al, Ba, Ca, Fe, Hg, K, Mg, Mn, P, Rb and Zn (p > 0.05), while they were similar in Cd, Co, Cr, Cu, Na, Ni, Pb and Sr (p < 0.05). The results of this study imply that metallic elements content of Parasol Mushroom collected at the same undisrupted sites, and hence keeping the same geochemical condition for mushroom development and fructification (the same stands and probably the same mycelia), can fluctuate over the years or the life-span of mycelium. Hence, when assessing the nutritional value of essential metallic elements and status of non-essential or toxic metallic elements in Parasol's Mushroom caps (and probably also of other mushrooms species) to man, the possible fluctuation in contents over time have to be taken into account.     

Multi-elemental analysis of Lentinula edodes mushrooms available in trade

ABSTRACT

The present study investigated the content of 62 elements in the fruiting bodies of Lentinula edodes (Shiitake mushroom) cultivated commercially in Poland on various substrates from 2007–2015. The general mean content (mg kg^?1 dry weight (DW)) of the studied elements ranked in the following order: K (26,335) > P (11,015) > Mg (2,284) > Ca (607) > Na (131) > Zn (112) > Fe (69) > Mn (33) > B (32) > Rb (17) > Cu (14.5) > Al (11.2) > Te (2.9) > As (1.80) > Cd (1.76) > Ag (1.73) > Nd (1.70) > Sr (1.46) > Se (1.41) > U (1.11) > Pt (0.90) > Ce (0.80) > Ba (0.61) > Co (0.59) > Tl (0.58) > Er (0.50) > Pb (0.42) > Li (0.40) > Pr (0.39) > Ir (0.37) > In (0.35) > Mo (0.31) > Cr (0.29) > Ni (0.28) > Sb (0.26) > Re (0.24) > Ti (0.19) > Bi (0.18) > Th (0.12) > La (0.10) = Pd (0.10) > Os (0.09) = Zr (0.09) > Rh (0.08) > Ho (0.07) > Ru (0.06) > Sm (0.04) = Eu (0.04) = Tm (0.04) > Gd (0.03) > Sc (0.02) = Y (0.02) > Lu (0.01) = Yb (0.01) = V (0.01). The contents of Au, Be, Dy, Ga, Ge, Hf, and Tb were below the limits of detection (0.02, 0.02, 0.01, 0.01, 0.01, 0.01, 0.02 mg kg^?1 respectively). The concentrations of Al, As, B, Ba, Ca, Cd, Cr, Er, Fe, In, Lu, Mn, Nd, Sr, Ti, Tm, and Zr were comparable over the period the mushrooms were cultivated. The study revealed that Lentinula edodes contained As and Cd at levels potentially adverse to human health. This highlights the need to monitor these elements in food products obtained from this mushroom species and ensure that only low levels of these elements are present in cultivation substrates.     

Characterization of the incipient smoke point for steam-/air-assisted and nonassisted flares

Flares are important safety devices for pressure relief; at the same time, flares are a significant point source for soot and highly reactive volatile organic compounds (HRVOCs). Currently, simple guidelines for flare operations to maintain high combustion efficiency (CE) remain elusive. This paper fills the gap by investigating the characteristics of the incipient smoke point (ISP), which is widely recognized as the condition for good combustion. This study characterizes the ISP in terms of 100–% combustion inefficiency (CE), percent opacity, absorbance, air assist, steam assist, air equivalence ratio, steam equivalence ratio, exit velocity, vent gas net heating value, and combustion zone net heating value. Flame lengths were calculated for buoyant and momentum-dominated plumes under calm and windy conditions at stable and neutral atmosphere. Opacity was calculated using the Beer–Lambert law based on soot concentration, flame diameter, and mass-specific extinction cross section of soot. The calculated opacity and absorbance were found to be lognormally distributed. Linear relations were established for soot yield versus absorptivity with R² > 0.99 and power-law relations for opacity versus soot emission rate with R² ≥ 0.97 for steam-assisted, air-assisted, and nonassisted flares. The characterized steam/air assists, combustion zone/vent gas heating values, exit velocity, steam, and air equivalence ratios for the incipient smoke point will serve as a useful guideline for efficient flare operations.

Implications: A Recent EPA rule requires an evaluation of visible emissions in terms of opacity in compliance with the standards. In this paper, visible emissions such as soot particles are characterized in terms of opacity at ISP. Since ISP is widely recognized as most efficient flare operation for high combustion efficiency (CE)/destruction efficiency (DE) with initial soot particles formed in the flame, this characterization provides a useful guideline for flare operators in the refinery, oil and gas, and chemical industries to sustain smokeless and high combustion efficiency flaring in compliance with recent EPA regulations, in addition to protecting the environment.     

UV-visible spectroscopy of organic carbon particulate sampled from ethylene/air flames

A systematic comparison of spectra obtained with extra and in situ diagnostics in the soot preinception region of rich, premixed ethylene air flames suggests that combustion generated organic carbon (OC) particulate can be extracted from flames and isolated from other flame material for further chemical analysis. Both the trend with height above the burner and the form of UV fluorescence and absorption spectra from extra situ sampled material captured in water agree with those measured in situ. These results show that the OC particulate formed in flames is partially water soluble. However, the collection efficiency can be increased using less polar solvents, like acetonitrile and dichloromethane. The fluorescence spectra from the water samples are comprised both a naphthalene-like component and a broad band UV fluorescence component similar to that observed in situ which is attributed to flame generated OC particulate. The broad band UV fluorescence centered around 320 nm is also observed very early in flames and does not change considerably with increasing flame residence time. These results support previous hypotheses that the UV broad band fluorescence is from carbonaceous material comprised two-ring aromatics, formed earlier than soot in the flame, and is still present along with soot at higher heights or flame residence times.     

Mass spectrometry up to 1 million mass units for the simultaneous detection of primary soot and of soot precursors (nanoparticles) in flames

A hybrid setup consisting of low pressure burner, flow reactor and photo-ionization mass spectrometer was used for the simultaneous detection of primary soot and of flame generated nanoparticles precursing soot. The studied flames were low pressure (120-180 mbar) C2H4/O2 flames surrounded by an N2 shield. The flow reactor was not used in this study. Through variation of the burner conditions (stoichiometry, sampling height) it could be shown that nanoparticles and soot are entirely independent species. The former, in particular, are found very early in the flame and their concentration profiles do not vary very much throughout the flame. This renders the possibility that nanoparticles are emitted together with soot and consequently may constitute an additional environmental hazard. Photo-ionization mass spectrometry is well suited for the detection of these particles.     

Inorganic elemental concentrations in birch bolete mushroom (Leccinum scabrum) and top soil: contamination profiles,bioconcentation and annual variations

Abstract

Analysis of inorganic and organic contaminants in foodstuffs aids in understanding the human exposure to these compounds via consumption. In this study, an edible mushroom species (Leccinum scabrum) and top soil samples were analysed for essential and toxic substances including phosphorus and inorganic elements over a period of three fruiting seasons. Analysis of silver (Ag), aluminium (Al), barium (Ba), calcium (Ca), cadmium (Cd), cobalt (Co), copper (Cu), iron (Fe), mercury (Hg), potassium (K), magnesium (Mg), manganese (Mn), sodium (Na), nickel (Ni), phosphorus (P), lead (Pb), rubidium (Rb), strontium (Sr) and zinc (Zn) in mushrooms and topsoil were performed using inductively coupled plasma optical emission spectroscopy (ICP-OES) with ultrasonic cross flow nebulizer. Total mercury was determined by cold-vapour atomic absorption spectroscopy (CV-AAS). The results exhibited wide variation in concentrations of metals between soil and mushroom (cap and stipes) during three fruiting seasons. Positive bioconcentration factors (BFCs) indicate on bioaccumulation of several metals including, Cd, Cu, Hg, K, Mg, Na, P, Rb and Zn in caps and stipes of fruitbodies of this mushroom, while other metals such as Al, Ba, Ca, Co, Fe, Mn, Ni, Pb and Sr were not exhibiting significant positive BFCs. Over a period studied, the caps were characterised by different (p?<?0.05) concentrations of Al, Co, Cu, Hg, Mn, Ni, P, Pb and Sr. Contamination profiles, temporal fluctuations, BCFs should be taken into consideration when assessing the nutritional value of this mushroom.     

Emission factors and exposures from ground-level pyrotechnics

Potential exposures from ground-level pyrotechnics were assessed by air monitoring and developing emission factors. Total particulate matter, copper and SO₂ exposures exceeded occupational health guidelines at two outdoor performances using consumer pyrotechnics. Al, Ba, B, Bi, Mg, Sr, Zn, and aldehyde levels were elevated, but did not pose a health hazard based on occupational standards. Emission factors for total particulate matter, metals, inorganic ions, aldehydes, and polyaromatic hydrocarbons (PAHs) were determined for seven ground-supported pyrotechnics through air sampling in an airtight room after combustion. Particle generation ranged from 5 to 13% of the combusted mass. Emission factors (g Kg^?1) for metals common to pyrotechnics were also high: K, 23–45; Mg, 1–7; Cu, 0.05–7; and Ba, 0.03–6. Pb emission rates of 1.6 and 2.7% of the combusted mass for two devices were noteworthy. A high correlation (r² ≥ 0.89) between metal concentrations in pyrotechnic compositions and emission factors were noted for Pb, Cr, Mg, Sb, and Bi, whereas low correlations (r² ≤ 0.1) were observed for Ba, Sr, Fe, and Zn. This may be due to the inherent heterogeneity of multi-effect pyrotechnics. The generation of inorganic nitrogen in both the particulate (NO₂^?, NO₃^?) and gaseous (NO, NO₂) forms varied widely (<0.1–1000 mg Kg^?1). Aldehyde emission factors varied by two orders of magnitude even though the carbon source was carbohydrates and charcoal for all devices: formaldehyde (<7.0–82 mg Kg^?1), acetaldehyde (43–210 mg Kg^?1), and acrolein (1.9–12 mg Kg^?1). Formation of lower molecular weight PAHs such as naphthalene and acenaphthylene were favored, with their emission factors being comparable to that from the combustion of household refuse and agricultural debris. Ba, Sr, Cu, and Pb had emission factors that could produce exposures exceeding occupational exposure guidelines. Sb and unalloyed Mg, which are banned from consumer fireworks in the US, were present in significant amounts.     

Study on transformation and enrichment behavior of selenium in particulate matter in combustion flame

An ethylene/air inverse diffusion flame (IDF) burner was employed to generate a stable flame, and selenium was introduced into the combustion flame in vapor phase under different air-fuel ratio (A/F) with SO2 additive. At different height above burner (HAB) along the flame edge, selenium of different speciation (gaseous selenium and particulate selenium) was sampled via the U.S. EPA method 29, and the samples were determined by hydride generation atomic fluorescence spectrometry (HG-AFS), in order to study the mechanism of transformation and enrichment behavior of selenium during the combustion process. The results showed that selenium presented in vapor phase, crossing the flame into air, which means gaseous phase is the main form of selenium during combustion process. Both gaseous selenium and particulate selenium increased with elevated temperature from 820K to 1650K, suggesting that higher temperature is beneficial to the release of selenium. Low concentration of sulfur dioxide would increase the concentration of particulate selenium and gaseous selenium, and accelerate the release of selenium.

Implications: The enrichment behavior of selenium and its transformation in combustion flame were studied. The results showed that gaseous selenium is found in higher quantity in compared to particulate selenium during combustion. Higher temperature and air–fuel ratio will cause an increase in the formation of selenium. While the presence of sulfur dioxide in a range of 0–200 ppm will promote the release of selenium, higher sulfur dioxide level in a range of 200–350 ppm will have a reverse effect.