Air quality measurements from the Fresno Supersite

The Fresno Supersite intends to 1) evaluate non-routine monitoring methods, establishing their comparability with existing methods and their applicability to air quality planning, exposure assessment, and health effects studies; 2) provide a better understanding of aerosol characteristics, behavior, and sources to assist regulatory agencies in developing standards and strategies that protect public health; and 3) support studies that evaluate relationships between aerosol properties, co-factors, and observed health end-points. Supersite observables include in-situ, continuous, short-duration measurements of 1) PM2.5, PM10, and coarse (PM10 minus PM2.5) mass; 2) PM2.5 SO4(-2), NO3-, carbon, light absorption, and light extinction; 3) numbers of particles in discrete size bins ranging from 0.01 to approximately 10 microns; 4) criteria pollutant gases (O3, CO, NOx); 5) reactive gases (NO2, NOy, HNO3, peroxyacetyl nitrate [PAN], NH3); and 6) single particle characterization by time-of-flight mass spectrometry. Field sampling and laboratory analysis are applied for gaseous and particulate organic compounds (light hydrocarbons, heavy hydrocarbons, carbonyls, polycyclic aromatic hydrocarbons [PAH], and other semi-volatiles), and PM2.5 mass, elements, ions, and carbon. Observables common to other Supersites are 1) daily PM2.5 24-hr average mass with Federal Reference Method (FRM) samplers; 2) continuous hourly and 5-min average PM2.5 and PM10 mass with beta attenuation monitors (BAM) and tapered element oscillating microbalances (TEOM); 3) PM2.5 chemical speciation with a U.S. Environmental Protection Agency (EPA) speciation monitor and protocol; 4) coarse particle mass by dichotomous sampler and difference between PM10 and PM2.5 BAM and TEOM measurements; 5) coarse particle chemical composition; and 6) high sensitivity and time resolution scalar and vector wind speed, wind direction, temperature, relative humidity, barometric pressure, and solar radiation. The Fresno Supersite is coordinated with health and toxicological studies that will use these data in establishing relationships with asthma, other respiratory disease, and cardiovascular changes in human and animal subjects.     

Identification of sources of atmospheric PM at the Pittsburgh Supersite—Part III: Source characterization

Single-particle mass spectrometry data collected during the Pittsburgh Supersite experiment was used to isolate an episode on 27 October 2001 when the measurement site was primarily influenced by emissions from coal combustion sources. Results showed that (a) 60–80% of the particles detected during this event belonged to the Na/Si/K/Ca/Fe/Ga/Pb particle class associated with coal combustion emissions, (b) observation of this class was an isolated event occurring only during the hours of 06:00–14:00 EST, and (c) the detection of these particles was highly correlated with shifts in wind direction. Coincident SMPS, TEOM PM_2.5, SO₂, NO_x, and O₃ measurements were in excellent agreement with the single-particle results in terms of both identifying and characterizing this event. The three most likely point sources of these particles were isolated and Gaussian plume dispersion models were used in reverse to predict their particle number, particle mass, and gas phase emissions. Calculated mass emission rates were in general agreement with the US EPA National Emissions Inventory (NEI) database emissions estimates and the Title V PM₁₀ limit. The largest of the three sources emits about 2.4×10¹⁷ fine and ultrafine particles per second.     

Errors in coarse particulate matter mass concentrations and spatiotemporal characteristics when using subtraction estimation methods

In studies of coarse particulate matter (PM_10-2.5), mass concentrations are often estimated through the subtraction of PM_2.5 from collocated PM₁₀ tapered element oscillating microbalance (TEOM) measurements. Though all field instruments have yet to be updated, the Filter Dynamic Measurement System (FDMS) was introduced to account for the loss of semivolatile material from heated TEOM filters. To assess errors in PM_10-2.5 estimation when using the possible combinations of PM₁₀ and PM_2.5 TEOM units with and without FDMS, data from three monitoring sites of the Colorado Coarse Rural–Urban Sources and Health (CCRUSH) study were used to simulate four possible subtraction methods for estimating PM_10-2.5 mass concentrations. Assuming all mass is accounted for using collocated TEOMs with FDMS, the three other subtraction methods were assessed for biases in absolute mass concentration, temporal variability, spatial correlation, and homogeneity. Results show collocated units without FDMS closely estimate actual PM_10-2.5 mass and spatial characteristics due to the very low semivolatile PM_10-2.5 concentrations in Colorado. Estimation using either a PM_2.5 or PM₁₀ monitor without FDMS introduced absolute biases of 2.4 µg/m³ (25%) to –2.3 µg/m³ (–24%), respectively. Such errors are directly related to the unmeasured semivolatile mass and alter measures of spatiotemporal variability and homogeneity, all of which have implications for the regulatory and epidemiology communities concerned about PM_10-2.5. Two monitoring sites operated by the state of Colorado were considered for inclusion in the CCRUSH acute health effects study, but concentrations were biased due to sampling with an FDMS-equipped PM_2.5 TEOM and PM₁₀ TEOM not corrected for semivolatile mass loss. A regression-based model was developed for removing the error in these measurements by estimating the semivolatile concentration of PM_2.5 from total PM_2.5 concentrations. By estimating nonvolatile PM_2.5 concentrations from this relationship, PM_10-2.5 was calculated as the difference between nonvolatile PM₁₀ and PM_2.5 concentrations.

Implications: Errors in the estimation of PM_10-2.5 concentrations using subtraction methods were shown to be related to the unmeasured semivolatile mass when using certain combinations of TEOM instruments. For the northeastern Colorado region, the absolute bias associated with this error significantly affects mean and 95th percentile values, which would affect assessment of compliance if PM_10-2.5 is regulated in the future. Estimating PM_10-2.5 mass concentrations using nonvolatile mass concentrations from collocated PM₁₀ and PM_2.5 TEOM monitors closely estimates the total PM_10-2.5 mass concentrations. A corrective model that removes the described error was developed and applied to data from two sites in Denver.

Supplemental Materials: Supplemental materials are available for this paper. Go to the publisher's online edition of the Journal of the Air & Waste Management Association.     

Regional Transport and Urban Contributions to Fine Particle Concentrations in Southeastern Canada

Abstract

The impact of various atmospheric transport directions on ambient fine particle (PM_2.5) concentrations at several sites in southeastern Canada was estimated (for May-September) using back-trajectory analysis. Three-day back trajectories (four per day) were paired with 6-hr average PM_2.5 mass concentrations measured using tapered element oscillating microbalances (TEOM). PM_2.5 concentrations at rural locations in the region were affected by nonlocal sources originating in both Canada and the United States. Comparison of sites revealed that, on average, the local contribution to total PM_2.5 in the greater Toronto area (GTA) is approximately 30–35%. At each location, average PM_2.5 concentrations under south/southwesterly flow conditions were 2–4 times higher than under the corresponding northerly flow conditions. The chemical composition of both urban and rural PM_2.5 was determined during two separate 2-week spring/summer measurement campaigns. Components identified included SO₄ ^2?, NO₃ ^?, NH₄+, black carbon and organic carbon (OC), and trace elements. Higher particle mass at the urban Toronto site was composed of a higher proportion of all components. However, black carbon, NO₃ ^?, NaCl, and trace elements were found to be the most enriched over the rural/regional background levels.     

Development and Evaluation of a Continuous Coarse (PM10–PM25) Particle Monitor

ABSTRACT

In this paper, we describe the development and laboratory and field evaluation of a continuous coarse (2.5-10 um) particle mass (PM) monitor that can provide reliable measurements of the coarse mass (CM) concentrations in time intervals as short as 5-10 min. The operating principle of the monitor is based on enriching CM concentrations by a factor of ~25 by means of a 2.5-um cut point round nozzle virtual impactor while maintaining fine mass (FM)—that is, the mass of PM_{2 5} at ambient concentrations. The aerosol mixture is subsequently drawn through a standard tapered element oscillating microbalance (TEOM), the response of which is dominated by the contributions of the CM, due to concentration enrichment. Findings from the field study ascertain that a TEOM coupled with a PM₁₀ inlet followed by a 2.5-um cut point round nozzle virtual impactor can be used successfully for continuous CM concentration measurements. The average concentration-enriched CM concentrations measured by the TEOM were 26-27 times higher than those measured by the time-integrated PM₁₀ samplers [the micro-orifice uniform deposit     

Comparison of Real-Time Instruments Used To Monitor Airborne Particulate Matter

ABSTRACT

Measurements collected using five real-time continuous airborne particle monitors were compared to measurements made using reference filter-based samplers at Bakers-field, CA, between December 2, 1998, and January 31, 1999. The purpose of this analysis was to evaluate the suitability of each instrument for use in a real-time continuous monitoring network designed to measure the mass of airborne particles with an aerodynamic diam less than 2.5 μm (PM_2.5) under wintertime conditions in the southern San Joaquin Valley. Measurements of airborne particulate mass made with a beta attenuation monitor (BAM), an integrating nephelometer, and a continuous aerosol mass monitor (CAMM) were found to correlate well with reference measurements made with a filter-based sampler. A Dusttrak aerosol sampler overestimated airborne particle concentrations by a factor of ~3 throughout the study. Measurements of airborne particulate matter made with a tapered element oscillating microbalance (TEOM) were found to be lower than the reference filter-based measurements by an amount approximately equal to the concentration of NH₄NO₃ observed to be present in the airborne particles. The performance of the Dusttrak sampler and the integrating nephelometer was affected by the size distribution of airborne particulate matter. The performance of the BAM, the integrating nephelometer, the CAMM, the Dusttrak sampler, and the TEOM was not strongly affected by temperature, relative humidity, wind speed, or wind direction within the range of conditions encountered in the current study. Based on instrument performance, the BAM, the integrating nephelometer, and the CAMM appear to be suitable candidates for deployment in a real-time continuous PM_2.5 monitoring network in central California for the range of winter conditions and aerosol composition encountered during the study.     

Particulate Matter in California: Part 2—Spatial,Temporal, and Compositional Patterns of PM2.5, PM10–2.5, and PM10

Abstract

Geographic and temporal variations in the concentration and composition of particulate matter (PM) provide important insights into particle sources, atmospheric processes that influence particle formation, and PM management strategies. In the nonurban areas of California, annual-average PM_2.5 and PM₁₀ concentrations range from 3 to 10 [H9262]g/m³ and from 5 to 18 µg/m³, respectively. In the urban areas of California, annual-averages for PM_2.5 range from 7 to 30 [H9262]g/m³, with observed 24-hr peaks reaching levels as high as 160 [H9262]g/m³. Within each air basin, exceedances are a mixture of isolated events as well as periods of elevated PM_2.5 concentrations that are more prolonged and regional in nature. PM_2.5 concentrations are generally highest during the winter months. The exception is the South Coast Air Basin, where fairly high values occur throughout the year. Annual-average PM_2.5 mass, as well as the concentrations of major components, declined from 1988 to 2000. The declines are especially pronounced for the sulfate (SO₄ ^2?) and nitrate (NO₃ ^?) components of PM_2.5 and PM₁₀ and correlate with reductions in ambient levels of oxides of sulfur (SO_x) and oxides of nitrogen (NO_x). Annual averages for PM_10–2.5 and PM₁₀ exhibited similar downwind trends from 1994 to 1999, with a slightly less pronounced decrease in the coarse fraction.     

Studies of the coarse particle (2.5–10 μm) component in UK urban atmospheres

An analysis is presented of continuous simultaneous measurement data for PM₁₀ and PM_2.5 using TEOM instruments from five sites in the United Kingdom. The results are analysed specifically in relation to the sources and processes influencing the coarse particle fraction (2.5–10 μm). The data show a generally strong correlation between fine and coarse particle concentrations at all sites, with a generally higher proportion of coarse particles in the dryer months of the year. The one rural site shows a notably lower proportion of coarse particles than the urban and suburban sites. Whilst it is possible to disaggregate the coarse particle concentrations into a component which is diluted by increasing windspeed and a component which increases with windspeed and is hence possibly attributable to wind-induced resuspension processes, the latter is only a minor proportion of the total coarse particle concentration. There are appreciable weekday-to-weekend and day-to-night differences between coarse particle concentrations which are most marked at the urban sites indicative of anthropogenic activities being a source of coarse particles. The clearest indication of the likely predominant source of coarse particles arises from an analysis of a data set derived from an urban street canyon site after subtraction of measurements from a nearby urban background location. The data indicate strong relationships of both fine and coarse incremental particle concentrations in the street canyon with incremental NO_x. If incremental fine particles and coarse particles are attributed to exhaust emissions and vehicle-induced resuspension, respectively, then it may be concluded that vehicle-induced resuspension provides a source strength approximately equal to that of exhaust emissions. An analysis of the coarse particle concentration data suggest that episodes of elevated coarse particle concentrations alone very rarely lead to exceedence of the UK air quality standard for PM₁₀ of 50 μg m⁻³ measured as a 24-h running mean.     

Human Exposure to Sulfates from Coal-Fired Power Plants

Abstract

Increased interest in the health effects of ambient par–ticulate mass (PM) has focused attention on the evaluation of existing mass measurement methodologies and the definition of PM in ambient air. The Rupprecht and Patashnick Tapered Element Oscillating MicroBalance (TEOM^®) method for PM is compared with time–integrated gravimetric (manual) PM methods in large urban areas during different seasons. Comparisons are conducted for both PM₁₀ and PM_2.5 concentrations.

In urban areas, a substantial fraction of ambient PM can be semi–volatile material. A larger fraction of this component of PM₁₀ may be lost from the TEOM–heated filter than the Federal Reference Method (FRM). The observed relationship between TEOM and FRM methods varied widely among sites and seasons. In East Coast urban areas during the summer, the methods were highly correlated with good agreement. In the winter, correlation was somewhat lower, with TEOM PM concentrations generally lower than the FRM. Rubidoux, CA, and two Mexican sites (Tlalnepantla and Merced) had the highest levels of PM₁₀ and the largest difference between TEOM and manual methods.

PM_2.5 data from collocation of 24–hour manual samples with the TEOM are also presented. As most of the semi–volatile PM is in the fine fraction, differences between these methods are larger for PM_2.5 than for PM₁₀.     

Chemical characterization of particles in winter-night smog in Tokyo

Continuous measurement of PM₁₀, PM_2.5 and carbon (organic, elemental composition) concentrations, and samples of PM₁₀ and PM_2.5 collected on a polycarbonate membrane filter (Nuclepore^®, pore size: 0.8 μm), were carried out during a period from December 1998 to January 1999 at Shinjuku in Tokyo in order to investigate the chemical characterization of particles in winter-night smog within a large area of the Japan Kanto Plain including the Tokyo Metropolitan area. These were measured using an ambient particulate monitor (tapered element oscillating microbalance—TEOM) and a carbon particulate monitor. Elemental compositions in the filter samples of PM₁₀ and PM_2.5 were determined by means of particle-induced X-ray emission (PIXE) analysis. Ionic species (anion: F⁻, Cl⁻, NO₃⁻, SO₄²⁻ and C₂O₄²⁻; cation: Na⁺, NH₄⁺, K⁺, Ca²⁺ and Mg²⁺) in the filter samples were analyzed by ion chromatography. The temporal variation patterns of PM_2.5 were similar to those of PM₁₀ and carbon. PM_2.5 made up 90% of the PM₁₀ at a high concentration, and 70% at a low concentration. Concentrations of 22 elements in both the PM₁₀ and PM_2.5 samples were consistently determined by PIXE, and Na, Mg, Al, Si, S, Cl, K, Ca, Fe, Zn and Pb were found to be the major components. Among these S and Cl were the most dominant elements of the PM_2.5 and PM₁₀ at high concentrations. Ionic species were mainly composed of Cl⁻, NO₃⁻, SO₄²⁻ and NH₄⁺. The component proportion of carbon, the other elements (total amount of measured elements other than S and Cl) and secondary-formed particles of PM_2.5 was similar to that of PM₁₀. The major component was carbon particles at a low concentration and secondary-formed particles at a high concentration. The proportion of NH₄NO₃ and NH₄Cl plus HCl in secondary-formed particles at a high concentration, in particular, was as high as 90%.     

Spatial differences in ambient coarse and fine particles in the Monterrey metropolitan area,Mexico: Implications for source contribution

The ambient air of the Monterrey Metropolitan Area (MMA) in Mexico frequently exhibits high levels of PM₁₀ and PM_2.5. However, no information exists on the chemical composition of coarse particles (PM_c = PM₁₀ – PM_2.5). A monitoring campaign was conducted during the summer of 2015, during which 24-hr average PM₁₀ and PM_2.5 samples were collected using high-volume filter-based instruments to chemically characterize the fine and coarse fractions of the PM. The collected samples were analyzed for anions (Cl^–, NO₃^–, SO₄^2–), cations (Na⁺, NH₄⁺, K⁺), organic carbon (OC), elemental carbon (EC), and 35 trace elements (Al to Pb). During the campaign, the average PM_2.5 concentrations did not showed significance differences among sampling sites, whereas the average PM_c concentrations did. In addition, the PM_c accounted for 75% to 90% of the PM₁₀ across the MMA. The average contribution of the main chemical species to the total mass indicated that geological material including Ca, Fe, Si, and Al (45%) and sulfates (11%) were the principal components of PM_c, whereas sulfates (54%) and organic matter (30%) were the principal components of PM_2.5. The OC-to-EC ratio for PM_c ranged from 4.4 to 13, whereas that for PM_2.5 ranged from 3.97 to 6.08. The estimated contribution of Secondary Organic Aerosol (SOA) to the total mass of organic aerosol in PM_2.5 was estimated to be around 70–80%; for PM_c, the contribution was lower (20–50%). The enrichment factors (EF) for most of the trace elements exhibited high values for PM_2.5 (EF: 10–1000) and low values for PM_c (EF: 1–10). Given the high contribution of crustal elements and the high values of EFs, PM_c is heavily influenced by soil resuspension and PM_2.5 by anthropogenic sources. Finally, the airborne particles found in the eastern region of the MMA were chemically distinguishable from those in its western region.

Implications: Concentration and chemical composition patterns of fine and coarse particles can vary significantly across the MMA. Public policy solutions have to be built based on these observations. There is clear evidence that the spatial variations in the MMA’s coarse fractions are influenced by clearly recognizable primary emission sources, while fine particles exhibit a homogeneous concentration field and a clear spatial pattern of increasing secondary contributions. Important reductions in the coarse fraction can come from primary particles’ emission controls; for fine particles, control of gaseous precursors—particularly sulfur-containing species and organic compounds—should be considered.     

Evaluation of the RAMS Continuous Monitor for Determination of PM2.5 Mass Including Semi-Volatile Material in Philadelphia,PA

Abstract

The real-time ambient mass sampler (RAMS) is a continuous monitor based on particle concentrator, denuder, drier, and tapered element oscillating microbalance (TEOM) monitor technology. It is designed to measure PM_2.5 mass, including the semi-volatile species NH₄NO₃ and semi-volatile organic material, but not to measure PM_2.5 water content. The performance of the RAMS in an urban environment with high humidity was evaluated during the July 1999 NARSTO-Northeast Oxidant and Particles Study (NEOPS) intensive study at the Baxter water treatment plant in Philadelphia, PA. The results obtained with the RAMS were compared to mass measurements made with a TEOM monitor and to constructed mass obtained with a Particle Concentrator-Brigham Young University Organic Sampling System (PC-BOSS) sampler designed to determine the chemical composition of fine particles, including the semi-volatile species. An average of 28% of the fine particulate material present during the study was semi-volatile organic material lost from a filter during particle collection, and 1% was NH₄NO₃ that was also lost from the particles during sampling. The remaining mass was dominantly nonvolatile (NH₄)₂SO₄ (31%) and organic material (37%), with minor amounts of soot, crustal material, and nonvolatile NH₄NO₃. Comparison of the RAMS and PC-BOSS results indicated that the RAMS correctly monitored for fine particulate mass, including the semi-volatile material. In contrast, the heated filter of the TEOM monitor did not measure the semi-volatile material. The comparison of the RAMS and PC-BOSS data had a precision of ±4.1 μg/m³ (±9.6%). The precision of the RAMS data was limited by the uncertainty in the blank correction for the reversible adsorption of water by the charcoal-impregnated cellulose sorbent filter of the RAMS monitor. The precision of the measurement of fine par-ticulate components by the PC-BOSS was ±6-8%.     

Particulate matter emissions from on-road vehicles in a freeway tunnel study

Particulate matter, including coarse particles (PM_2.5–10, aerodynamic diameter of particle between 2.5 and 10 μm) and fine particles (PM_2.5, aerodynamic diameter of particle lower than 2.5 μm) and their compositions, including elemental carbon, organic carbon, and 11 water-soluble ionic species, and elements, were measured in a tunnel study. A comparison of the six-hour average of light-duty vehicle (LDV) flow of the two sampling periods showed that the peak hours over the weekend were higher than those on weekdays. However, the flow of heavy-duty vehicles (HDVs) on the weekdays was significant higher than that during the weekend in this study. EC and OC content were 49% for PM_2.5–10 and 47% for PM_2.5 in the tunnel center. EC content was higher than OC content in PM_2.5–10, but EC was about 2.3 times OC for PM_2.5. Sulfate, nitrate, ammonium were the main species for PM_2.5–10 and PM_2.5. The element contents of Na, Al, Ca, Fe and K were over 0.8 μg m^?3 in PM_2.5–10 and PM_2.5. In addition, the concentrations of S, Ba, Pb, and Zn were higher than 0.1 μg m^?3 for PM_2.5–10 and PM_2.5. The emission factors of PM_2.5–10 and PM_2.5 were 18 ± 6.5 and 39 ± 11 mg km^?1-vehicle, respectively. The emission factors of EC/OC were 3.6/2.7 mg km^?1-vehicle for PM_2.5–10 and 15/4.7 mg km^?1-vehicle for PM_2.5 Furthermore, the emission factors of water-soluble ions were 0.028(Mg²⁺)–0.81(SO₄^2?) and 0.027(NO₂^?)–0.97(SO₄^2?) mg km^?1-vehicle for PM_2.5–10 and PM_2.5, respectively. Elemental emission factors were 0.003(V)–1.6(Fe) and 0.001(Cd)–1.05(Na) mg km^?1-vehicle for PM_2.5–10 and PM_2.5, respectively.     

The Steubenville Comprehensive Air Monitoring Program (SCAMP): Analysis of Short-Term and Episodic Variations in PM2.5 Concentrations Using Hourly Air Monitoring Data

Abstract

One-hour average ambient concentrations of particulate matter (PM) with an aerodynamic diameter <2.5 μm (PM_2.5) were determined in Steubenville, OH, between June 2000 and May 2002 with a tapered element oscillating microbalance (TEOM). Hourly average gaseous copollutant [carbon monoxide (CO), sulfur dioxide (SO₂), nitrogen oxide (NO_x), and ozone (O₃)] concentrations and meteorological conditions also were measured. Although 75% of the 14,682 hourly PM_2.5 concentrations measured during this period were ≤17 μg/m³, concentrations >65 μg/m³ were observed 76 times. On average, PM_2.5 concentrations at Steubenville exhibited a diurnal pattern of higher early morning concentrations and lower afternoon concentrations, similar to the diurnal profiles of CO and NO_x. This pattern was highly variable; however, PM_2.5 concentrations >65 μg/m³ were never observed during the mid-afternoon between 1:00 p.m. and 5:00 p.m. EST. Twenty-two episodes centered on one or more of these elevated concentrations were identified. Five episodes occurred during the months June through August; the maximum PM_2.5 concentration during these episodes was 76.6 μg/m³. Episodes occurring during climatologically cooler months often featured higher peak concentrations (five had maximum concentrations between 95.0 and 139.6 μg/m³), and many exhibited strong covariation between PM_2.5 and CO, NO_x, or SO₂. Case studies suggested that nocturnal surface-based temperature inversions were influential in driving high nighttime concentrations of these species during several cool season episodes, which typically had dramatically lower afternoon concentrations. These findings provide insights that may be useful in the development of PM_2.5 reduction strategies for Steubenville, and suggest that studies assessing possible health effects of PM_2.5 should carefully consider exposure issues related to the intraday timing of PM_2.5 episodes, as well as the potential for toxicological interactions among PM_2.5 and primary gaseous pollutants.     

Wintertime and summertime São Paulo aerosol source apportionment study

A detailed aerosol source apportionment study was performed with two sampling campaigns, during wintertime and summertime in the heavily polluted metropolitan area of São Paulo, Brazil. In addition to 12 h fine and coarse mode filter sampling, several real time aerosol and trace gas monitors were used. PM₁₀ was sampled using stacked filter units that collects fine (d<2.5 μm) and coarse (2.5<d<10 μm) particulate matter, providing mass, black carbon (BC) and elemental concentration for each aerosol mode. The concentration of about 20 elements was determined using the particle induce X-ray emission technique. Real time aerosol monitors provided PM₁₀ aerosol mass (TEOM), organic and elemental carbon (Carbon Monitor 5400, R&P) and BC concentration (Aethalometer). A complex system of sources and meteorological conditions modulates the heavy air pollution of the urban area of São Paulo. The boundary layer height and the primary emissions by motor vehicles controls the strong pattern of diurnal cycles obtained for PM₁₀, BC, CO, NO_x, and SO₂. Absolute principal factor analysis results showed a very similar source pattern between winter and summer field campaigns, despite the different locations of the sampling sites of both campaigns, pointing that there are no significant change in the main air pollution sources. The source identified as motor vehicle represented 28% and 24% of the PM_2.5 for winter and summer, respectively. Resuspended soil dust accounted for 25% and 30%. The oil combustion source represented 18% and 21%. Sulfates accounts for 23% and 17% and finally industrial emissions contributed with 5% and 6% of PM_2.5, for winter and summer, respectively. The resuspended soil dust accounted for a large fraction (75–78%) of the coarse mode aerosol mass. Certainly automobile traffic and soil dust are the main air pollution sources in São Paulo. The sampling and analytical procedures applied in this study showed that it is possible to perform a quantitative aerosol source apportionment in a complex urban area such as São Paulo.     

Source Identification of Atlanta Aerosol by Positive Matrix Factorization

Abstract

Data characterizing daily integrated particulate matter (PM) samples collected at the Jefferson Street monitoring site in Atlanta, GA, were analyzed through the application of a bilinear positive matrix factorization (PMF) model. A total of 662 samples and 26 variables were used for fine particle (particles ≤2.5 µm in aerodynamic diameter) samples (PM_2.5 ), and 685 samples and 15 variables were used for coarse particle (particles between 2.5 and 10 µm in aerodynamic diameter) samples (PM_10–2.5 ). Measured PM mass concentrations and compositional data were used as independent variables. To obtain the quantitative contributions for each source, the factors were normalized using PMF-apportioned mass concentrations. For fine particle data, eight sources were identified: SO₄ ^2?-rich secondary aerosol (56%), motor vehicle (22%), wood smoke (11%), NO₃ ^?-rich secondary aerosol (7%), mixed source of cement kiln and organic carbon (OC) (2%), airborne soil (1%), metal recycling facility (0.5%), and mixed source of bus station and metal processing (0.3%). The SO₄ ^2?-rich and NO₃ ^?-rich secondary aerosols were associated with NH₄ ⁺. The SO₄ ^2?-rich secondary aerosols also included OC. For the coarse particle data, five sources contributed to the observed mass: airborne soil (60%), NO₃ ^?-rich secondary aerosol (16%), SO₄ ^2?-rich secondary aerosol (12%), cement kiln (11%), and metal recycling facility (1%). Conditional probability functions were computed using surface wind data and identified mass contributions from each source. The results of this analysis agreed well with the locations of known local point sources.     

Aerosol Measurement: The Use of Optical Light Scattering for the Determination of Particulate Size Distribution,and Particulate Mass,Including the Semi-Volatile Fraction

Abstract

The GRIMM model 1.107 monitor is designed to measure particle size distribution and particulate mass based on a light scattering measurement of individual particles in the sampled air. The design and operation of the instrument are described. Protocols used to convert the measured size number distribution to a mass concentration consistent with U.S. Environmental Protection Agency protocols for measuring particulate matter (PM) less than 10 μm (PM₁₀) and less than 2.5 μm (PM_2.5) in aerodynamic diameter are described. The performance of the resulting continuous monitor has been evaluated by comparing GRIMM monitor PM_2.5 measurements with results obtained by the Rupprecht and Patashnick Co. (R&P) filter dynamic measurement system (FDMS). Data were obtained during month-long studies in Rubidoux, CA, in July 2003 and in Fresno, CA, in December 2003. The results indicate that the GRIMM monitor does respond to total PM_2.5 mass, including the semi-volatile components, giving results comparable to the FDMS. The data also indicate that the monitor can be used to estimate water content of the fine particles. However, if the inlet to the monitor is heated, then the instrument measures only the nonvolatile material, more comparable to results obtained with a conventional heated filter tapered element oscillating microbalance (TEOM) monitor. A recent modification of the model 180, with a Nafion dryer at the inlet, measures total PM_2.5 including the nonvolatile and semi-volatile components, but excluding fine particulate water. Model 180 was in agreement with FDMS data obtained in Lindon, UT, during January through February 2007     

The Southeastern Aerosol Research and Characterization Study,Part 3: Continuous Measurements of Fine Particulate Matter Mass and Composition

Abstract

Deployment of continuous analyzers in the Southeastern Aerosol Research and Characterization Study (SEARCH) network began in 1998 and continues today as new technologies are developed. Measurement of fine particulate matter (PM_2.5) mass is performed using a dried, 30 °C tapered element oscillating microbalance (TEOM). TEOM measurements are complemented by observations of light scattering by nephelometry. Measurements of major constituents include: (1) SO₄ ^2? via reduction to SO₂; (2) NH₄ ⁺ and NO₃ ^? via respective catalytic oxidation and reduction to NO, (3) black carbon (BC) by optical absorption, (4) total carbon by combustion to CO₂, and (5) organic carbon by difference between the latter two measurements. Several illustrative examples of continuous data from the SEARCH network are presented. A distinctive composite annual average diurnal pattern is observed for PM_2.5 mass, nitrate, and BC, likely indicating the influence of traffic-related emissions, growth, and break up of the boundary layer and formation of ammonium nitrate. Examination of PM_2.5 components indicates the need to better understand the continuous composition of the unmeasured “other” category, because it contributes a significant fraction to total mass during periods of high PM_2.5 loading. Selected episodes are presented to illustrate applications of SEARCH data. An SO₂ conversion rate of 0.2%/hr is derived from an observation of a plume from a coal-fired power plant during early spring, and the importance of local, rural sources of NH₃ to the formation of ammonium nitrate in particulate matter (PM) is demonstrated.     

Comparison of Fine Particles and the Relationship between Particle Variations and Meteorology at an Urban Site and a Remote Site in the Eastern United States

Abstract

This study compared the variations in the mass of certain particles at an urban site, Washington, DC, and at a remote site, Shenandoah National Park, VA, in the eastern United States. Seven years (1991-1997) of Interagency Monitoring of Protected Visual Environments (IMPROVE) fine particulate matter (PM_2.5), PM₁₀, coarse fraction, SO₄ ^2?, and total sulfur data were used for this study together with available meteorology/climatology data. Various statistical modeling and analysis procedures, including time series analysis, factor analysis, and regression modeling, were employed. Time series of the constituents were divided into four terms: the long-term mean, the intra-annual perturbation, the interannual perturbation, and the synoptic perturbation. PM_2.5 at the two sites made up ~72% of the total mass for PM₁₀, and the coarse fraction made up the remaining 28%, on average. Thirty-one percent of the PM_2.5 at the DC site and 42% at the Shenandoah site was SO₄ ^2?, based on average data for the entire period. At the DC site, the two main contributors to the constituent mass were the long-term mean and the synoptic perturbation terms, and at the Shenandoah site, they were the long-term mean and the intra-annual perturbation terms. This suggested that the constituent mass at the two sites was affected by very different processes. The terms that provided the principal contribution to the constituent mass at the two sites were studied in detail.

At the DC site, dew point trends, a climate variable, were the primary driver of the 7-year trends for PM_2.5, PM₁₀, the coarse fraction, and total sulfur, and SO₂ emission trends were the primary driver of the trends for SO₄ ^2?. SO₂ emission trends influenced the trends for PM_2.5 and total sulfur, appearing as the second term in the model, but only parameters dealing with climate trends had significant effects on the trends for PM₁₀ and the coarse fraction. At the Shenandoah site, only parameters dealing with climate trends affected long-term particle trends.     

Effects of Equilibration Temperature on PM10 Concentrations from the TEOM Method in the Lower Fraser Valley

ABSTRACT

This study investigated the effect of equilibration temperature on PM₁₀ concentrations from the tapered element oscillating microbalance (TEOM) method by operating collocated TEOM monitors at different equilibration temperatures in an airshed (the Lower Fraser Valley, British Columbia). This airshed contained an abundance of par-ticulate semivolatile material (PSVM). For the period when three collocated TEOM monitors were operated, the PM₁₀ from the monitor at an equilibration temperature of 30 ° C was 2.5 μ g/m³ (22%) and 1.7 (17%) μ g/m³ higher, on average, than the PM₁₀ from monitors at 50 and 40 ° C, respectively, and the differences were proportional to the ambient PM₁₀ loading. Greater volatilization of PSVM in the TEOM monitors at higher equilibration temperatures may have been a cause of the differences.