Microwave regeneration of activated carbon used for removal of solvents from vented air

A microwave regeneration of activated carbon used to remove organic solvents from vented air has been investigated. Methyl ethyl ketone (MEK), acetone, and tetrachloroethylene (TCE) vapors were removed from vented air through adsorption onto granular activated carbon. The saturated carbon was then regenerated in a microwave field, where the solvent was quickly desorbed and recovered from the inner pores of the carbon granules. The microwave-induced regeneration restored the original adsorption capacity and surface area of the activated carbon.     

Microwave Process for Volatile Organic Compound Abatement

ABSTRACT

The CHA Corporation has completed the U.S. Air Force Phase II Small Business Innovation Research program to investigate the feasibility of using a novel microwave-based process for the removal and destruction of volatile organic compounds (VOCs) in effluents from noncombustion sources, such as paint booth ventilation streams. Removal of solvents by adsorption, followed by the regeneration of saturated granular activated carbon (GAC) by microwave energy, was achieved in a single fixed-bed reactor. Microwave regeneration of the fixed-bed-saturated carbon restored the original GAC adsorption capacity. After 20 adsorption/regeneration cycles, the adsorption capacity dropped from 13.5 g methyl ethyl ketone (MEK)/100 g GAC to 12.5 g MEK/100 g GAC. During microwave regeneration of the GAC fixed bed, the concentrated desorbed paint solvent was oxidized by passing the solvent mixture through a fixed bed of an oxidation catalyst mixed with silicon carbide in a microwave reactor. A 98% oxidation efficiency was consistently achieved from the oxidation of VOCs in the microwave catalytic reactor.     

海绵铁还原耦合活性炭吸附-微波再生技术降解甲基橙

采用海绵铁(s-Fe0)还原耦合活性炭(GAC)吸附-微波(MW)再生技术降解甲基橙(MO)溶液,重点考察了s-Fe0投加量、粒径、微波功率等因素对MO去除效果的影响。结果表明,s-Fe0投加剂量为15.0 g/L、粒径为3～5 mm、超声波功率为200 W,反应1 h,MO的去除率为94.2%。其次,采用GAC吸附-MW再生技术(800 W,照射1 min)循环处理上述脱色后的MO废水。结果表明,GAC吸附可有效降低废水的生物毒性及残留的染料、TOC和总铁离子浓度,且MW辐射可有效再生吸附饱和的GAC颗粒。因此,s-Fe0还原耦合GAC吸附-MW再生技术可以有效降解MO染料,具有处理效果好、实现资源循环利用等优点。     

浸渍-碱性微波法载磁活性炭粉对壬基酚的吸附

利用浸渍-碱性微波法制备载磁粉末活性炭,通过等温吸附实验和动力学吸附实验,研究对比了其与原料活性炭、浸渍载铁活性炭对壬基酚的吸附性能。采用氮气吸附仪、FTIR、XRD、国标(GB/T12496.19-1999)邻菲啰啉分光度法及VSM,分别对3种样品进行了物相结构、表面官能团、铁含量及磁性能的分析,并探讨了吸附机理。结果表明,浸渍-碱性微波法载磁活性炭的总孔容及孔隙率均有较大提高;其吸附等温线符合Freundich方程,吸附动力学过程符合准二级动力学方程与孔道内扩散模型,相关系数R2均大于0.900。原活性炭经一定浓度的铁盐溶液浸渍后,铁含量由2%提高到8%。在碱性、N2气氛条件下微波后,铁系物主要存在形式为零价铁和Fe3O4,制得的载磁活性炭饱和磁化强度为1.12 emu/g。     

微波法制备污泥活性炭研究

采用微波加热法,以污水厂剩余污泥为原料,磷酸为污泥活化剂制备污泥活性炭.微波功率、辐照时间和磷酸浓度对污泥活性炭吸附性能具有显著影响,在最佳工艺条件微波功率480 W、辐照时间315 s和磷酸浓度40%条件下制得的活性炭碘值301 mg/g,比表面积168 m2/g,污泥中重金属绝大部分被固化.与传统商品炭相比,污泥炭孔隙结构以中孔为主.利用该活性炭处理城市生活污水处理厂出水,COD去除率可达87%以上,污泥炭的吸附等温线用Langmuir等温吸附模型进行描述.     

Microwave process for volatile organic compound abatement

The CHA Corporation has completed the U.S. Air Force Phase II Small Business Innovation Research program to investigate the feasibility of using a novel microwave-based process for the removal and destruction of volatile organic compounds (VOCs) in effluents from noncombustion sources, such as paint booth ventilation streams. Removal of solvents by adsorption, followed by the regeneration of saturated granular activated carbon (GAC) by microwave energy, was achieved in a single fixed-bed reactor. Microwave regeneration of the fixed-bed-saturated carbon restored the original GAC adsorption capacity. After 20 adsorption/regeneration cycles, the adsorption capacity dropped from 13.5 g methyl ethyl ketone (MEK)/100 g GAC to 12.5 g MEK/100 g GAC. During microwave regeneration of the GAC fixed bed, the concentrated desorbed paint solvent was oxidized by passing the solvent mixture through a fixed bed of an oxidation catalyst mixed with silicon carbide in a microwave reactor. A 98% oxidation efficiency was consistently achieved from the oxidation of VOCs in the microwave catalytic reactor.     

Determination of the Adsorption Isotherm of Vapor-Phase Mercury Chloride on Powdered Activated Carbon Using Thermogravimetric Analysis

Abstract

This study investigated the use of thermogravimetric analysis (TGA) to determine the adsorptive capacity and adsorption isotherm of vapor-phase mercury chloride on powdered activated carbon (PAC). The technique is commonly applied to remove mercury-containing air pollutants from gas streams emitted from municipal solid waste incinerators. An alternative form of powdered activated carbon derived from a pyrolyzed tire char was prepared for use herein. The capacity of waste tire-derived PAC to adsorb vapor-phase HgCl₂ was successfully measured using a self-designed TGA adsorption system. Experimental results showed that the maximum adsorptive capacities of HgCl₂ were 1.75, 0.688, and 0.230 mg of HgCl₂ per gram of powdered activated carbon derived from carbon black at 30, 70, and 150 °C for 500 µg/m³ of HgCl₂, respectively. Four adsorption isotherms obtained using the Langmuir, Freundlich, Redlich-Peterson, and Brunauer–Emmett–Teller (BET) models were used to simulate the adsorption of HgCl₂. The comparison of experimental data associated with the four adsorption isotherms indicated that BET fit the experimental results better than did the other isotherms at 30 °C, whereas the Freundlich isotherm fit the experimental results better at 70 and 150 °C. Furthermore, the calculations of the parameters associated with Langmuir and Freundlich isotherms revealed that the adsorption of HgCl₂ by PAC-derived carbon black favored adsorption at various HgCl₂ concentrations and temperatures.     

Effect of Advanced Oxidants Generated Via Ultraviolet Light on a Sequentially Loaded and Regenerated Granular Activated Carbon Biofilter

Abstract

The objective of this research was to investigate a sequentially loaded and regenerated granular activated carbon (GAC) biofilter system and to determine whether regenerative ozonation/advanced oxidation could improve the removal and biodegradation of a volatile organic compound from a contaminated airstream. Bench-scale reactors were constructed to operate in a manner analogous to a commercially available system manufactured by Terr-Aqua Environmental Systems (only with longer contact time). The GAC system consisted of two GAC biofilter beds that operated in a cyclical manner. On a given day, the first GAC bed adsorbed methyl isobutyl ketone from a simulated waste airstream, while the second bed underwent regeneration; then on the next day, the second bed was in the adsorption mode while the first was regenerated.

Three bench-scale systems were used to compare the performance under three operating conditions: (1) ozone/ associated oxidant regeneration of a GAC biofilter system that was seeded with microorganisms from a field site, (2) a humid air regeneration of a seeded GAC biofilter, and (3) a humid air regeneration of an unseeded GAC biofilter. For the advanced oxidant regenerated GAC biofilter, a maximum removal efficiency of >95% was achieved with an empty bed contact time of 148 sec and an influent concentration of 125 ppm methyl isobutyl ketone, and 90–95% was achieved at 148-sec empty bed contact time and a 1150-ppm influent.     

微波加热及真空集成再生活性炭

吸附法油气回收技术中,吸附剂的再生是一个难点和研究重点。微波加热再生作为一种新技术,受到人们的广泛关注。运用正交实验,研究了微波功率、辐照时间、活性炭量和真空度对吸附了汽油油气的富活性炭的再生率和损耗率的影响,发现影响顺序为微波功率〉辐照时间〉活性炭量〉真空度。综合考虑各方面因素,得出实验的最优方案为微波功率300W、辐照时间240s、活性炭量4g、真空度O．06MPa。还研究了活性炭多次吸附一再生后平衡吸附率和表面结构的变化。结果表明,微波和真空法对活性炭的表面结构影响不大,有利于活性炭的多次循环利用。综合比较真空再生法、真空和加热再生法、微波和真空再生法的再生效果,结果表明,微波和真空再生法稳定性较好。     

Comprehending adsorption of methylethylketone and toluene and microwave regeneration effectiveness for beaded activated carbon derived from recycled waste bamboo tar

ABSTRACT

Beaded activated carbons (BACs) were derived from waste bamboo tar through carbonization (500°C for 2 hr) followed by physical activation using carbon dioxide (800–900°C for 2–4 hr). The adsorbent was examined for their physical and chemical properties, adsorption capacities toward methylethylketone (MEK) and toluene, and regenerabilities under microwave heating. It was found that the maximum total surface area reached for bamboo-tar-derived BAC after physical activation was 1364 m² g^?1, and more than 95% of the area was attributed to the microporous structures. Langmuir, Freundlich, and Dubinin-Radushkevich (D-R) isotherm models were applied to the adsorption isotherm fitting, and the minimum R² for each model was 0.986, 0.915, and 0.943, respectively. The isosteric heats of adsorption calculated based on D-R parameters for methylethylketone and toluene were 44.04 to 51.50 and 45.88 to 73.27 KJ mol^?1, respectively. They were slightly over the range of physisorption and increased with adsorbate loading, which might be related to the micropore filling mechanism. Microwave regeneration under 600 W of power output removed most of the adsorbate (>93.03%) within 8 min. The results of this study are intended to benefit future study on waste-derived adsorbent in environmental applications.     

微波辐射回用活性炭对水中亚甲基蓝和Cd~(2+)去除效果的研究

考察了微波-活性炭联合处理技术对模拟染料废水中亚甲基蓝和Cd2+的去除效果。对于100 mL浓度为1 000 mg/L的亚甲基蓝溶液、活性炭用量为10 g时,新活性炭对亚甲基蓝的去除率为99.99%;采用700 W微波对吸附亚甲基蓝的活性炭辐射10 min进行再生并回用,经微波辐射再生10次后活性炭对亚甲基蓝的去除率为99.68%,未经微波作用反复使用10次的活性炭对亚甲基蓝的去除率为85.41%。结果表明:微波处理有效地减缓了活性炭吸附能力的下降速率,实现了活性炭再生和反复使用。在吸附过程中,Cd2+使活性炭对亚甲基蓝的吸附能力略有下降,而共存的亚甲基蓝则促进了活性炭对Cd2+的吸附,对新炭和再生后活性炭物理化学特性的表征证明了活性炭对亚甲基蓝的吸附为物理吸附,对Cd2+的吸附为化学吸附。     

Activated carbon/Fe(3)O(4) nanoparticle composite: fabrication, methyl orange removal and regeneration by hydrogen peroxide

In the water treatment field, activated carbons (ACs) have wide applications in adsorptions. However, the applications are limited by difficulties encountered in separation and regeneration processes. Here, activated carbon/Fe₃O₄ nanoparticle composites, which combine the adsorption features of powdered activated carbon (PAC) with the magnetic and excellent catalytic properties of Fe₃O₄ nanoparticles, were fabricated by a modified impregnation method using HNO₃ as the carbon modifying agent. The obtained composites were characterized by X-ray diffraction, scanning and transmission electron microscopy, nitrogen adsorption isotherms and vibrating sample magnetometer. Their performance for methyl orange (MO) removal by adsorption was evaluated. The regeneration of the composite and PAC-HNO₃ (powdered activated carbon modified by HNO₃) adsorbed MO by hydrogen peroxide was investigated. The composites had a high specific surface area and porosity and a superparamagnetic property that shows they can be manipulated by an external magnetic field. Adsorption experiments showed that the MO sorption process on the composites followed pseudo-second order kinetic model and the adsorption isotherm date could be simulated with both the Freundlich and Langmuir models. The regeneration indicated that the presence of the Fe₃O₄ nanoparticles is important for a achieving high regeneration efficiency by hydrogen peroxide.     

VOC Recovery through Microwave Regeneration of Adsorbents: Comparative Economic Feasibility Studies

ABSTRACT

Microwave regeneration of adsorbents facilitates the recovery of volatile organic compounds (VOCs) by decoupling the bed heating from the stripping gas. This makes possible the creation of a highly-concentrated regeneration effluent from which the VOCs can be recovered by condensation at near-ambient temperatures. The economic feasibility of two novel microwave-regenerated adsorption systems was evaluated by systematically comparing the capital and operating costs of the proposed systems with 10 conventional VOC control technologies. The microwave systems were found to have similar capital and operating costs to conventional steam regeneration systems and, therefore, may present an attractive alternative for recovering water-miscible solvents. In general, the cost of the microwave subsystem is a relatively small component of the overall system costs, and the microwave power requirements are within the range of commercially available generators, even for large emission streams.     

不同再生工艺对活性炭吸附性能的影响分析

吸附法油气回收技术中,吸附剂的再生是一个难点和研究重点。微波加热作为一种新的再生技术,受到人们日益的重视。实验利用比表面积及孔隙分析仪测定了经多次微波真空,加热真空和加热再生后的活性炭的表面结构变化,通过对比分析,探讨了3种工艺多次再生活性炭对活性炭表面结构的影响。结果表明,3种工艺均对活性炭结构都有所破坏,但微波真空再生对活性炭比表面积和孔容破坏最小,净吸附容量最大,从效率及能耗上都比较好。     

微波再生载苯酚活性炭过程中再生产物分析

研究了载氮气和无载气2种条件下,微波再生载苯酚活性炭过程中再生产物的成分和苯酚随再生过程的去向分布。结果表明,无载气时,微波功率越高,再生反应器内温度越高,吸附质的高温裂解反应越彻底,再生产物以挥发性气体为主,有机质种类很少;而当微波功率较低或载氮气再生时,反应器内温度相对较低,苯酚难以被彻底分解,再生产物中含多种复杂的链状或环状有机物。此外,载氮气时,经气提、挥发而去除的苯酚量约占总吸附量的一半,再生炭上无苯酚残留,活性炭吸附性能可完全恢复乃至优化;无载气时,经挥发而去除的苯酚量只有19.9%,其余大量苯酚则在微波作用下裂解或缩合为其他物质随尾气而去除,且再生炭上仍有少量苯酚未被解吸出来。因此,前者活性炭再生的效果优于后者。     

Optimization of preparation process of activated carbon from chestnut burs assisted by microwave and pore structural characterization analysis

In this study, activated carbon was prepared from Chinese chestnut burs assisted by microwave irradiation with potassium hydroxide (KOH) as activator, and the process conditions were optimized employing Box-Behnken design (BBD) and response surface methodology (RSM). The optimized variables were irradiation time, impregnation time, and mass ratio of alkali-to-carbon, and the iodine adsorption value was used to evaluate the adsorption property of activated carbon. The optimal preparation conditions were determined as follows: irradiation time 17 min, impregnation time 240 min, and mass ratio of alkali-to-char 1.5:1. Meanwhile, the relatively high iodine adsorption value (1141.4 mg/g) was also obtained. Furthermore, the pore structural characterization of activated carbon was analyzed. The analyzed results showed a larger Brunauer-Emmett-Teller (BET) specific surface area (1254.5 m²/g) and a higher microporosity ratio (87.2%), a bigger total pore volume (0.6565 m³/g), but a smaller average pore size (2.093 nm), which demonstrated the obtained activated carbon possessed strong adsorption capacity and well-developed microporous structure. This research could not only establish the foundation of utilizing chestnut burs to prepare activated carbon, but also provide the basis for exploitation of Chinese chestnut by-products.

Implications: Because Chinese chestnut burs are the by-products and usually discarded upon harvesting subsequently, the utilization of chestnut burs as a potential source of activated carbon is of great profit to the chestnut processing industries.     

Removal of acutely hazardous pharmaceuticals from water using multi-template imprinted polymer adsorbent

Molecularly imprinted polymer adsorbent has been prepared to remove a group of recalcitrant and acutely hazardous (p-type) chemicals from water and wastewaters. The polymer adsorbent exhibited twofold higher adsorption capacity than the commercially used polystyrene divinylbenzene resin (XAD) and powdered activated carbon adsorbents. Higher adsorption capacity of the polymer adsorbent was explained on the basis of high specific surface area formed during molecular imprinting process. Freundlich isotherms drawn showed that the adsorption of p-type chemicals onto polymer adsorbent was kinetically faster than the other reference adsorbents. Matrix effect on adsorption of p-type chemicals was minimal, and also polymer adsorbent was amenable to regeneration by washing with water/methanol (3:1, v/v) solution. The polymer adsorbent was unaltered in its adsorption capacity up to 10 cycles of adsorption and desorption, which will be more desirable in cost reduction of treatment compared with single-time-use activated carbon.     

A Sorptive Slurry Bioscrubber for the Control of Acetone

ABSTRACT

A sorptive slurry bioscrubber adds powdered activated carbon (PAC) to a conventional suspended-growth bioscrubber. The activated carbon increases pollutant removal from the gas phase due to adsorption on carbon. The carbon is bioregenerated in the oxidation reactor and recycled to the scrubbing column. A three-stage, conventional bioscrubber was tested with and without carbon. The experiments showed that the PAC improved the removal efficiency of the system and that bioregeneration occurred. At an inlet gas-phase acetone concentration of 50 ppmv, the steady-state removal increased from 88 to 95% when activated carbon was added to the biological slurry.     

Performance Evaluation of Waste Activated Carbon on Atrazine Removal from Contaminated Water

Abstract

In this study, the potential of spent activated carbon from water purifier (Aqua Guard, India) for the removal of atrazine (2 chloro-4 ethylamino-6-isopropylamino-1, 3, 5 triazine) from wastewaters was evaluated. Different grades of spent activated carbon were prepared by various pretreatments. Based on kinetic and equilibrium study results, spent activated carbon with a grain size of 0.3–0.5 mm and washed with distilled water (designated as WAC) was selected for fixed column studies. Batch adsorption equilibrium data followed both Freundlich and Langmuir isotherm. Fixed bed adsorption column with spent activated carbon as adsorbent was used as a polishing unit for the removal of atrazine from the effluent of an upflow anaerobic sludge blanket (UASB) reactor treating atrazine bearing domestic wastewater. Growth of bacteria on the surface of WAC was observed during column study and bacterial activity enhanced the effectiveness of adsorbent on atrazine removal from wastewater.     

微波辅助-活性炭法处理电厂EDTA锅炉清洗废水可行性研究

采用微波辅助-活性炭法处理电厂EDTA锅炉清洗废水,研究了微波辐射时间、微波功率以及再生次数对活性炭吸附能力的影响,并根据实验结果设计了工艺流程,分析了微波辅助-活性炭法处理电厂EDTA锅炉清洗废水的可行性.研究表明,微波辅助-活性炭法处理EDTA清洗废水的最佳微波辐射时间和微波功率分别为5 min和680 W,微波辐...