Principal Plume Dispersion Models: TVA Power Plants

The body of information presented in this paper is directed to those individuals who may be concerned with principal plume dispersion models at coal-burning power plants. About 20 years of comprehensive field surveillance and documentation of dispersion of power plant emissions for a varied range of unit sizes, stack heights, and meteorological conditions have determined the Tennessee Valley Authority’s interpretation of principal plume dispersion models. TVA’s experience indicates that as unit sizes are increased and taller stacks are constructed, the plume dispersion model associated with maximum surface concentrations changes. Maximum surface concentrations for principal plume dispersion models were approximately equal for the early small plants. However, the coning model was considered the critical plume dispersion model because the frequency of recurrence of surface concentrations from this model was appreciably greater than other models.

There were progressive changes because of an increase in unit sizes and stack heights; the magnitude of maximum surface concentrations from the coning model decreased, and the magnitude (relative to the coning model) of concentrations from the inversion breakup model increased. However, with plumes from newer and larger units with higher stacks, the trapping dispersion model became prominent. Finally, by the time unit size had increased to 900 mw and stack height to about 245 meters, as at Bull Run Power Plant, the magnitude of surface concentrations associated with trapping had increased to such a degree that it became the critical dispersion model identified with power plants of this size.     

Characterization of Particulates from Power Plants

The emphasis on participate control from industrial processes has been shifted recently towards fine particulates, having diameters less than 3 microns. There exists an urgent need for more scientific information of fine particle characterization.^1,2 Coal and oil fired power plants are among the largest anthropogenic point sources of particulate matter.³ Limited knowledge is available on particle size distribution and trace metal composition in power plant emissions.^4-7 The morphological properties of particle emissions have been largely neglected. In this report we present some information on particle characteristics for an oil-fired and coal-fired power plant.     

The Bag Filterhouse for Oil-Fired Power Plants

This Report, published as Informative Report No. 7 of the Air Pollution Control Association’s TI-5 Public Utilities Committee, began to move through the 14 step approval procedure of APCA’s Technical Council in February 1964 Comments made by members of the Technical Council were considered in the preparation of the final report. It is now published as representing the best thinking of the Association. It is an extremely timely and informative report.     

国外火电厂的烟气脱氮技术

火电厂是NOx污染的主要来源之一,全球NOx的排放量目前已达5.5亿t左右,每年造成的损失高达数百亿美元.如果不加以控制,将会给人类环境带来巨大的破坏.国内外火力发电厂的烟气脱氮装置大多以气相反应法、液体吸收法、吸附法等为主.     

The Fate and Behavior of Mercury in Coal-Fired Power Plants

Abstract

For the past 22 years in the Netherlands, the behavior of Hg in coal-fired power plants has been studied extensively. Coal from all over the world is fired in Dutch power stations. First, the Hg concentrations in these coals were measured. Second, the fate of the Hg during combustion was established by performing mass balance studies. On average, 43 ± 30% of the Hg was present in the flue gases downstream of the electrostatic precipitator (ESP; dust collector). In individual cases, this figure can vary between 1 and 100%. Important parameters are the Cl content of the fuel and the flue gas temperature in the ESP. On average, 54 ± 24% of the gaseous Hg was removed in the wet flue-gas desulfurization (FGD) systems, which are present at all Dutch coal-power stations. In individual cases, this removal can vary between 8% (outlier) and 72%.

On average, the fate of Hg entering the power station in the coal was as follows: <1% in the bottom ash, 49% in the pulverized fuel ash (ash collected in the ESP), 16.6% in the FGD gypsum, 9% in the sludge of the wastewater treatment plant, 0.04% in the effluent of the wastewater treatment plant, 0.07% in fly dust (leaving the stack), and 25% as gaseous Hg in the flue gases and emitted into the air. The distribution of Hg over the streams leaving the FGD depends strongly on the installation. On average, 75% of the Hg was removed, and the final concentration of Hg in the emitted flue gases of the Dutch power stations was only ~3 μg/m_STP ³ at 6% O₂. During co-combustion with biomass, the removal of Hg was similar to that during 100% coal firing.

Speciation of Hg is a very important factor. An oxidized form (HgCl₂) favors a high degree of removal. The conversion from Hg⁰ to HgCl₂ is positively correlated with the Cl content of the fuel. A catalytic DENOX (SCR) favors the formation of oxidized Hg, and, in combination with a wet FGD, the total removal can be as high as 90%.     

Fabric Filter Technology for Utility Coal-Fired Power Plants

This is the fifth in a series of papers discussing the experience of electric utilities in applying baghouse technology for the collection of particulate matter at coal-fired electric power generating plants. The series presents new data obtained in research sponsored by the Electric Power Research Institute (EPRI) on reverse-gas and shake/deflate cleaned baghouses, and specifically addresses a number of unresolved issues in the design and operation of these units. This paper describes research to improve reverse-gas cleaning technology, and to characterize reverse-gas sonic assisted and shake/deflate cleaning.     

New Source Performance Standards For Coal-Fired Power Plants

To preserve and improve environmental quality in a prosperous industrialized nation like the United States, we must use efficient control technology to reduce the pollution which would otherwise accompany our growth. The need for control is especially great in our use of energy. In the near term our country must depend increasingly on coal to meet our energy needs. In his 1977 energy message President Carter declared that it would be this Administration’s policy to require the use of best available control technology for all new coal burning plants. EPA is implementing this policy by adopting a rule that will require such controls on new coal-fired power plants.     

Fabric Filter Technology for Utility Coal-Fired Power Plants

This is the third in a series of papers discussing the experience of electric utilities in applying baghouse technology for the collection of particulate matter at coal-fired electric power generating plants. The series presents new data obtained in research sponsored by the Electric Power Research Institute (EPRI) on reverse-gas and shake/deflate cleaned baghouses, and specifically addresses a number of unresolved issues in the design and operation of these units. This paper provides an overview of the design and operating characteristics of baghouses now in place in the utility industry. In addition, it discusses three key issues in design and operation: the relationships among dust cake weight and chemical composition, air-to-cloth ratio, and pressure drop; fabric selection; and bag life.     

Human Exposure to Sulfates from Coal-Fired Power Plants

Abstract

Increased interest in the health effects of ambient par–ticulate mass (PM) has focused attention on the evaluation of existing mass measurement methodologies and the definition of PM in ambient air. The Rupprecht and Patashnick Tapered Element Oscillating MicroBalance (TEOM^®) method for PM is compared with time–integrated gravimetric (manual) PM methods in large urban areas during different seasons. Comparisons are conducted for both PM₁₀ and PM_2.5 concentrations.

In urban areas, a substantial fraction of ambient PM can be semi–volatile material. A larger fraction of this component of PM₁₀ may be lost from the TEOM–heated filter than the Federal Reference Method (FRM). The observed relationship between TEOM and FRM methods varied widely among sites and seasons. In East Coast urban areas during the summer, the methods were highly correlated with good agreement. In the winter, correlation was somewhat lower, with TEOM PM concentrations generally lower than the FRM. Rubidoux, CA, and two Mexican sites (Tlalnepantla and Merced) had the highest levels of PM₁₀ and the largest difference between TEOM and manual methods.

PM_2.5 data from collocation of 24–hour manual samples with the TEOM are also presented. As most of the semi–volatile PM is in the fine fraction, differences between these methods are larger for PM_2.5 than for PM₁₀.     

Fabric Filter Technology for Utility Coal-Fired Power Plants

This is the sixth and last part in a series of papers discussing the experience of electric utilities in applying baghouse technology for the collection of particulate matter at coal-fired electric power generating plants. The series presents new data obtained in research sponsored by the Electric Power Research Institute (EPRI) on reverse-gas and shake/deflate cleaned baghouses, and specifically addresses a number of unresolved issues in the design and operation of these units. This paper discusses research, development and demonstration activities now underway or planned to further understand baghouse technology to ensure efficient, economic and reliable service in utility applications. In addition, it summarizes the major findings reported in Parts I through V.     

Mercury Mass Balances: A Case Study of Two North Dakota Power Plants

ABSTRACT

The Energy & Environmental Research Center (EERC) conducted a mercury-sampling program to provide data on the quantity and forms of Hg emitted and on the Hg removal efficiency of the existing air pollution control devices at two North Dakota power plants—Milton R. Young Station and Coal Creek Station. Minnkota Power Cooperative, Great River Energy, the North Dakota Industrial Commission, and EPRI funded the project. The primary objective was to obtain accurate measurements of Hg released from each plant, as verified by a material balance. A secondary objective was to evaluate the ability of a mercury continuous emission monitor (CEM) to measure total Hg at the stack.

At both plants, speciated Hg measurements were made at the inlets and outlets of both the electrostatic precipi-tators (ESPs) and the flue gas desulfurization (FGD) systems. A Semtech Hg 2000 (Semtech Metallurgy AB) mercury CEM was used to measure the total Hg emissions at the stack in real time. Using these measurements and plant data, the measured Hg concentrations in the coal, FGD slurries, and ESP ash, a Hg mass flow rate was calculated at each sampling location. Excellent Hg mass balances were obtained (±15%). It was also found that the Hg was mostly in the elemental phase (~90%), and the small amount of oxidized Hg that was generated was removed by the FGD systems.

Insignificant amounts of particulate-bound Hg were measured at both plants. However, 10-20% of the elemental Hg measured prior to the ESP was converted to oxidized Hg across the ESP. The data show that, at these facilities, almost all of the Hg generated is being emitted into the atmosphere as elemental Hg. Local or regional deposition of the Hg emitted from these plants is not a concern. However, the Hg does become part of the global Hg burden in the atmosphere. Also, the evidence appears to indicate that elemental Hg is more difficult to remove from flue gas than oxidized Hg is.     

Sulfur Control In Coal Fired Power Plants: A Probabilistic Approach to Policy Analysis

The optimum level of sulfur pollution control for a coal fired power plant is the point where the sum of societal costs, due to pollution, and control costs is minimized. This basic microeconomic concept has been of limited practical value due to considerable uncertainty in estimating both costs. A probabilistic approach is used to characterize these uncertainties quantitatively for a hypothetical 1000 Mw_e plant located near Pittsburgh, Pennsylvania. Only mortality effects within a distance of 80 km of the plant have been included. The results allow explicit consideration of attitude toward risk and appropriate level of investment to prevent deaths. Limitations of the findings are discussed. Implications are described for policy based on alternative sets of values and assumptions.     

Quantification of Hourly Variability in NOx Emissions for Baseload Coal-Fired Power Plants

Abstract

The objectives of this paper are to (1) quantify variability in hourly utility oxides of nitrogen (NO_x) emission factors, activity factors, and total emissions; (2) investigate the autocorrelation structure and evaluate cyclic effects at short and long scales of the time series of total hourly emissions; (3) compare emissions for the ozone (O₃) season versus the entire year to identify seasonal differences, if any; and (4) evaluate interannual variability. Continuous emissions monitoring data were analyzed for 1995 and 1998 for 32 units from nine baseload power plants in the Charlotte, NC, airshed. Unit emissions have a strong 24-hr cycle attributable primarily to the capacity factor. Typical ranges of the coefficient of variation for emissions at a given hour of the day were from 0.2 to 0.45. Little difference was found when comparing weekend emissions with the entire week or when comparing the O₃ season with the entire year. There were substantial differences in the mean and standard deviation of emissions when comparing 1995 and 1998 data, indicative of the effect of retrofits of control technology during the intervening time. The wide range of variability and its autocorrelation should be accounted for when developing probabilistic utility emission inventories for analysis of near-term future episodes.     

Sulfur Dioxide Removal and Recovery from Pulp Mill Power Plants

The use of soda ash liquor to scrub SO₂ rich power plant flue gases was studied using an Airetron pilot scrubber with a maximum capacity of 3000 cfm. The relative effects of the major operating variables— temperature, soda ash concentration, and the gas/liquid flow ratio—on the absorption phenomenon were determined. Orthogonal factorial experiments were used to derive a response function relating mass transfer values to operating variables. The economics of a full scale NSSC installation are discussed.     

Third Conference on Fabric Filter Technology for Coal-Fired Power Plants

This paper summarizes information and results presented at the Third Conference on Fabric Filter Technology for Coal-Fired Power Plants held November 19-21, 1985 in Scottsdale, Arizona. Sponsored by the Electric Power Research Institute (EPRI), in cooperation with the Arizona Public Service Co. and Salt River Project, the conference focused on recent technological developments in the design and operation of fabric filters (baghouses) in electric utility settings. Papers were presented by individuals representing utilities, fabric filter manufacturers, research and development organizations, and regulatory agencies. Approximately 200 individuals attended the sessions. Summaries of the first two conferences and results of other fabric Biter research sponsored bv EPRI have been published previously in JAPCA.^1–9     

An Intelligent Emissions Controller for Fuel Lean Gas Reburn in Coal-Fired Power Plants

ABSTRACT

The application of artificial intelligence techniques for performance optimization of the fuel lean gas reburn (FLGR) system is investigated. A multilayer, feedforward artificial neural network is applied to model static nonlinear relationships between the distribution of injected natural gas into the upper region of the furnace of a coal-fired boiler and the corresponding oxides of nitrogen (NO_x) emissions exiting the furnace. Based on this model, optimal distributions of injected gas are determined such that the largest NO_x reduction is achieved for each value of total injected gas. This optimization is accomplished through the development of a new optimization method based on neural networks. This new optimal control algorithm, which can be used as an alternative generic tool for solving multidimensional nonlinear constrained optimization problems, is described and its results are successfully validated against an off-the-shelf tool for solving mathematical programming problems. Encouraging results obtained using plant data from one of Commonwealth Edison's coal-fired electric power plants demonstrate the feasibility of the overall approach.

Preliminary results show that the use of this intelligent controller will also enable the determination of the most cost-effective operating conditions of the FLGR system by considering, along with the optimal distribution of the injected gas, the cost differential between natural gas and coal and the open-market price of NO_x emission credits. Further study, however, is necessary, including the construction of a more comprehensive database, needed to develop high-fidelity process models and to add carbon monoxide (CO) emissions to the model of the gas reburn system.     

Technical Aspects of Lime/Limestone Scrubbers for Coal-Fired Power Plants

This 2-part article deals with the technical aspects of lime/limestone scrubbers for coal-fired power plants. Part I covers process chemistry and scrubber systems. Part II (next month) will cover instrumentation, particulate removal, and sludge disposal.     

Technical Aspects of Lime/Limestone Scrubbers for Coal-Fired Power Plants

This is the conclusion of a 2-part article dealing with the technical aspects of lime/limestone scrubbers for coal-fired power plants, it covers instrumentation, participate removal and sludge disposal. Part I (June JAPCA) covered process chemistry and scrubber systems