Effect of gasoline formulation on the formation of photosmog: a box model study

Based on exhaust gas analyses from the combustion of five different types of gasoline in a passenger car operated on a chassis dynamometer, box model simulations of the irradiation of exhaust/NOx/air mixtures using an established chemical mechanism for a standardized photosmog scenario were performed. The fuel matrix used covered wide fractional ranges for paraffinic, olefinic, and aromatic hydrocarbons. Two fuels also contained methyl tertiary butyl ether (MTBE). The different O3 profiles calculated for each run were compared and interpreted. The O3 levels obtained were strongly influenced by the exhaust gas concentrations of aromatic and olefinic hydrocarbons. The higher exhaust content of these compounds caused higher O3 production in the smog system investigated. The conclusion of the present study is that the composition of gasoline cannot be taken directly for the estimation of the emissions' O3 creation potential from its combustion. Variation of the dilution in the different calculations showed evidence for an additional influence of transport effects. Accordingly, further detailed exhaust gas analyses followed by more complex modeling studies are necessary for a proper characterization of the relationship between fuel blend and gasoline combustion products.     

Hazardous Air Pollutants from Mobile Sources in the Metropolitan Area of Mexico City

Abstract

Environmental agencies are currently in the process of implementing a new air management program, which includes the improvement of fuel quality. In this work, exhaust emissions data and estimated relative risk for various fuels testing in-use vehicles, equipped with three different exhaust emission control technologies, are presented. Aromatics, sulfur, and olefins contents; type of oxygenated compound; and Reid vapor pressure were varied. The aim also includes calculating the ozone (O₃)of forming potential and a relative cancer risk of emissions from current and formulated gasoline blends in Mexico. The proposed gasoline decreases carbon monoxide, total hydrocarbons (THC), and nitrogen oxides emissions by 18 and 14%, respectively, when compared with gasoline sold in the rest of the country and within ozone nonattainment metropolitan areas in Mexico, respectively.     

Identification of a potential source of chloroform in urban air: Preliminary Communication

A new potential source of elevated chloroform (CHCl₃) concentrations in urban air is reported. The exhaust gases from gasoline internal combustion engines operated on conventional “leaded” fuel and not equipped with catalytic converters contain parts-per-billion concentrations of chloroform which can, in congested urban areas, contribute significantly to the ambient concentration of chloroform. Exhaust gases from engines burning conventional “leaded” gasoline contain much higher levels of chloroform than do exhaust gases from engines equipped with catalytic converters and operating on “nonleaded” gasoline.     

Exhaust Emissions From In-Use Alternative Fuel Vehicles

Abstract

This study examines exhaust emissions from 11 vehicles tested on compressed natural gas, liquefied petroleum gas, methanol, ethanol, and reformulated gasoline fuels (22 vehicle/ fuel combinations). The paper highlights ozone precursor and toxic emissions. Emission rates from some of the presumably well-maintained, low-mileage test vehicles were higher than expected, but fuel effects were consistent with findings of similar studies. Aggregate toxic and non-methane organic emission rates from the variable/flexible fuel vehicles were higher with alcohol fuels than with reformulated gasoline. Lower specific reactivities for emissions with the alcohol fuels offset this negative trait. Specific reactivities of the organic emissions with the alternative fuels were consistently lower than those with the gasoline blends. Compressed natural gas and liquefied petroleum gas fuels had the lowest values. Although specific reactivities were expected to vary from fuel-to-fuel, they also varied considerably from vehicle-to-vehicle.     

Control of Diesel Gaseous and Particulate Emissions with a Tube-Type Wet Electrostatic Precipitator

Abstract

In this study, experiments were performed with a bench-scale tube-type wet electrostatic precipitator (wESPs) to investigate its effectiveness for the removal of mass- and number-based diesel particulate matter (DPM), hydrocarbons (HCs), carbon monoxide (CO), and oxides of nitrogen (NO_x) from diesel exhaust emissions. The concentration of ozone (O₃) present in the exhaust that underwent a nonthermal plasma treatment process inside the wESP was also measured. A nonroad diesel generator operating at varying load conditions was used as a stationary diesel emission source. The DPM mass analysis was conducted by means of isokinetic sampling and the DPM mass concentration was determined by a gravimetric method. An electrical low-pressure impactor (ELPI) was used to quantify the DPM number concentration. The HC compounds, n-alkanes, and polycyclic aromatic hydrocarbons (PAHs) were collected on a moisture-free quartz filter together with a PUF/XAD/PUF cartridge and extracted in dichloromethane with sonication. Gas chromatography (GC)/mass spectroscopy (MS) was used to determine HC concentrations in the extracted solution. A calibrated gas combustion analyzer (Testo 350) and an O₃ analyzer were used for quantifying the inlet and outlet concentrations of CO and NO_x (nitric oxide [NO] + nitrogen dioxide [NO₂]), and O₃ in the diesel exhaust stream. The wESP was capable of removing approximately 67–86% of mass- and number-based DPM at a 100% exhaust volumetric flow rate generated from 0- to 75-kW engine loads. At 75-kW engine load, increasing gas residence time from approximately 0.1 to 0.4 sec led to a significant increase of DPM removal efficiency from approximately 67 to more than 90%. The removal of n-alkanes, 16 PAHs, and CO in the wESP ranged from 31 to 57% and 5 to 38%, respectively. The use of the wESP did not significantly affect NO_x concentration in diesel exhaust. The O₃ concentration in diesel exhaust was measured to be less than 1 ppm. The main mechanisms responsible for the removal of these pollutants from diesel exhaust are discussed.     

A Life-Cycle Comparison of Alternative Automobile Fuels

ABSTRACT

We examine the life cycles of gasoline, diesel, compressed natural gas (CNG), and ethanol (C₂H₅OH)-fueled internal combustion engine (ICE) automobiles. Port and direct injection and spark and compression ignition engines are examined. We investigate diesel fuel from both petroleum and biosources as well as C₂H₅OH from corn, herbaceous bio-mass, and woody biomass. The baseline vehicle is a gasoline-fueled 1998 Ford Taurus. We optimize the other fuel/powertrain combinations for each specific fuel as a part of making the vehicles comparable to the baseline in terms of range, emissions level, and vehicle lifetime. Life-cycle calculations are done using the economic input-output life-cycle analysis (EIO-LCA) software; fuel cycles and vehicle end-of-life stages are based on published model results.

We find that recent advances in gasoline vehicles, the low petroleum price, and the extensive gasoline infrastructure make it difficult for any alternative fuel to become commercially viable. The most attractive alternative fuel is compressed natural gas because it is less expensive than gasoline, has lower regulated pollutant and toxics emissions, produces less greenhouse gas (GHG) emissions, and is available in North America in large quantities. However, the bulk and weight of gas storage cylinders required for the vehicle to attain a range comparable to that of gasoline vehicles necessitates a redesign of the engine and chassis. Additional natural gas transportation and distribution infrastructure is required for large-scale use of natural gas for transportation. Diesel engines are extremely attractive in terms of energy efficiency, but expert judgment is divided on whether these engines will be able to meet strict emissions standards, even with reformulated fuel. The attractiveness of direct injection engines depends on their being able to meet strict emissions standards without losing their greater efficiency. Biofuels offer lower GHG emissions, are sustainable, and reduce the demand for imported fuels. Fuels from food sources, such as biodiesel from soybeans and C₂H₅OH from corn, can be attractive only if the co-products are in high demand and if the fuel production does not diminish the food supply. C₂H₅OH from herbaceous or woody biomass could replace the gasoline burned in the light-duty fleet while supplying electricity as a co-product. While it costs more than gasoline, bioethanol would be attractive if the price of gasoline doubled, if significant reductions in GHG emissions were required, or if fuel economy regulations for gasoline vehicles were tightened.     

Hydrocarbon emissions speciation in diesel and biodiesel exhausts

Diesel engine emissions are composed of a long list of organic compounds, ranging from C₂ to C₁₂₊, and coming from the hydrocarbons partially oxidized in combustion or produced by pyrolisis. Many of these are considered as ozone precursors in the atmosphere, since they can interact with nitrogen oxides to produce ozone under atmospheric conditions in the presence of sunlight. In addition to problematic ozone production, Brookes, P., and Duncan, M. [1971. Carcinogenic hydrocarbons and human cells in culture. Nature.] and Heywood, J. [1988. Internal Combustion Engine Fundamentals.Mc Graw-Hill, ISBN 0-07-1000499-8.] determined that the polycyclic aromatic hydrocarbons present in exhaust gases are dangerous to human health, being highly carcinogenic.The aim of this study was to identify by means of gas chromatography the amount of each hydrocarbon species present in the exhaust gases of diesel engines operating with different biodiesel blends. The levels of reactive and non-reactive hydrocarbons present in diesel engine exhaust gases powered by different biodiesel fuel blends were also analyzed.Detailed speciation revealed a drastic change in the nature and quantity of semi-volatile compounds when biodiesel fuels are employed, the most affected being the aromatic compounds. Both aromatic and oxygenated aromatic compounds were found in biodiesel exhaust. Finally, the conservation of species for off-side analysis and the possible influence of engine operating conditions on the chemical characterization of the semi-volatile compound phase are discussed.The use of oxygenated fuel blends shows a reduction in the Engine-Out emissions of total hydrocarbons. But the potential of the hydrocarbon emissions is more dependent on the compositions of these hydrocarbons in the Engine-Out, to the quantity; a large percent of hydrocarbons existing in the exhaust, when biodiesel blends are used, are partially burned hydrocarbons, and are interesting as they have the maximum reactivity, but with the use of pure biodiesel and diesel, the most hydrocarbons are from unburned fuel and they have a less reactivity. The best composition in the fuel, for the control of the hydrocarbon emissions reactivity, needs to be a fuel with high-saturated fatty acid content.     

Idle Emissions from Medium Heavy-Duty Diesel and Gasoline Trucks

Abstract

Idle emissions data from 19 medium heavy-duty diesel and gasoline trucks are presented in this paper. Emissions from these trucks were characterized using full-flow exhaust dilution as part of the Coordinating Research Council (CRC) Project E-55/59. Idle emissions data were not available from dedicated measurements, but were extracted from the continuous emissions data on the low-speed transient mode of the medium heavy-duty truck (MHDTLO) cycle. The four gasoline trucks produced very low oxides of nitrogen (NO_x) and negligible particulate matter (PM) during idle. However, carbon monoxide (CO) and hydrocarbons (HCs) from these four trucks were approximately 285 and 153 g/hr on average, respectively. The gasoline trucks consumed substantially more fuel at an hourly rate (0.84 gal/hr) than their diesel counterparts (0.44 gal/hr) during idling. The diesel trucks, on the other hand, emitted higher NO_x (79 g/hr) and comparatively higher PM (4.1 g/hr), on average, than the gasoline trucks (3.8 g/hr of NO_x and 0.9 g/hr of PM, on average). Idle NO_x emissions from diesel trucks were high for post-1992 model year engines, but no trends were observed for fuel consumption. Idle emissions and fuel consumption from the medium heavy-duty diesel trucks (MHDDTs) were marginally lower than those from the heavy heavy-duty diesel trucks (HHDDTs), previously reported in the literature.     

A description of a test plant for combustion on a pilot scale

A plant for combustion on a pilot scale is described.The plant is comprised of two shaft furnaces connected to a common afterburning chamber. Sawmill chips and LP-gas are used as supporting fuel. The plant is provided with equipment for continuous feeding-in of both solid and liquid wastes.The products of decomposition and residual concentrations resulting from combustion of the wastes are analysed with respect to different organic compounds. These analyses are made on ingoing product, slag, dust and fuel gases. In addition, temperature, transit time, gas composition (CO, CO₂, O₂), fuelgas flow and - in some cases - parameters such as total hydrocarbon and nitrogen oxides are investigated.     

Source apportionment of PM2.5 at two Seattle chemical speciation sites

ABSTRACT

Positive Matrix Factorization analysis of PM_2.5 chemical speciation data collected from 2015–2017 at Washington State Department of Ecology’s urban NCore (Beacon Hill) and near-road (10th and Weller) sites found similar PM_2.5 sources at both sites. Identified factors were associated with gasoline exhaust, diesel exhaust, aged and fresh sea salt, crustal, nitrate-rich, sulfur-rich, unidentified urban, zinc-rich, residual fuel oil, and wood smoke. Factors associated with vehicle emissions were the highest contributing sources at both sites. Gasoline exhaust emissions comprised 26% and 21% of identified sources at Beacon Hill and 10th and Weller, respectively. Diesel exhaust emissions comprised 29% of identified sources at 10th and Weller but only 3% of identified sources at Beacon Hill. Correlation of the diesel exhaust factor with measured concentrations of black carbon and nitrogen oxides at 10th and Weller suggests a method to predict PM_2.5 from diesel exhaust without a full chemical speciation analysis. While most PM_2.5 sources exhibit minimal change over time, primary PM_2.5 from gasoline emissions is increasing on average 0.18 µg m^?3 per year in Seattle.     

Measurement of Ultrafine Particle Size Distributions from Coal-, Oil-, and Gas-Fired Stationary Combustion Sources

Abstract

Currently, we have limited knowledge of the physical and chemical properties of emitted primary combustion aerosols and the changes in those properties caused by nucleation, condensation growth of volatile species, and particle coagulations under dilution and cooling in the ambient air. A dilution chamber was deployed to sample exhaust from a pilot-scale furnace burning various fuels at a nominal heat input rate of 160 kW/h^?1 and 3% excess oxygen. The formation mechanisms of particles smaller than 420 nm in electrical mobility diameter were experimentally investigated by measurement with a Scanning Mobility Particle Sizer (SMPS) as a function of aging times, dilution air ratios, combustion exhaust temperatures, and fuel types. Particle formation in the dilution process is a complex mixture of nucleation, coagulation, and condensational growth, depending on the concentrations of available condensable species and solid or liquid particles (such as soot, ash) in combustion exhausts. The measured particle size distributions in number concentrations measured show peaks of particle number concentrations for medium sulfur bituminous coal, No. 6 fuel oil, and natural gas at 40-50 nm, 70-100 nm, and 15-25 nm, respectively. For No. 6 fuel oil and coal, the particle number concentration is constant in the range of a dilution air ratio of 50, but the number decreases as the dilution air ratio decreases to 10. However, for natural gas, the particle number concentration is higher at a dilution air ratio of 10 and decreases at dilution air ratios of 20-50. At a dilution air ratio of 10, severe particle coagulation occurs in a relatively short time. Samples taken at different combustion exhaust temperatures for these fuel types show higher particle number concentrations at 645 K than at 450 K. As the aging time of particles increases, the particles increase in size and the number concentrations decrease. The largest gradient of particle number distribution occurs within the first 10 sec after dilution but shows only minor differences between 10 and 80 sec. The lifetimes of the ultrafine particles are relatively short, with a scale on the order of a few seconds. Results from this study suggest that an aging time of 10 sec and a dilution air ratio of 20 are sufficient to obtain representative primary particle emission samples from stationary combustion sources.     

Composition of Exhaust from a Regenerative Turbine System

Particulate and hydrocarbon content of gases in a regenerative gas turbine was analyzed at several points. Particle samples were measured with a condensation nuclei counter, a light scattering single particle counter and an impactor. Hydrocarbon analyses were made using gas chromatography. The effects of operation with JP-4 and No. 2 fuel oil were noted. It was concluded that a regenerative gas turbine will not add appreciably to the burden of air pollution. In fact, particulate contamination levels in the exhaust less than those in the inlet air indicates that the high rotation rate may result in some air cleaning. Low hyd rocarbon contents in the exhaust gas were ascribed to efficient combustion under the operating conditions used in this work. In general, it was concluded that hydrocarbon levels significantly lower than those seen from gasoline or diesel engines could be expected from a well maintained and operated regenerative gas turbine.     

VOC composition of current motor vehicle fuels and vapors, and collinearity analyses for receptor modeling

The formulation of motor vehicle fuels can alter the magnitude and composition of evaporative and exhaust emissions occurring throughout the fuel cycle. Information regarding the volatile organic compound (VOC) composition of motor fuels other than gasoline is scarce, especially for bioethanol and biodiesel blends. This study examines the liquid and vapor (headspace) composition of four contemporary and commercially available fuels: gasoline (<10% ethanol), E85 (85% ethanol and 15% gasoline), ultra-low sulfur diesel (ULSD), and B20 (20% soy-biodiesel and 80% ULSD). The composition of gasoline and E85 in both neat fuel and headspace vapor was dominated by aromatics and n-heptane. Despite its low gasoline content, E85 vapor contained higher concentrations of several VOCs than those in gasoline vapor, likely due to adjustments in its formulation. Temperature changes produced greater changes in the partial pressures of 17 VOCs in E85 than in gasoline, and large shifts in the VOC composition. B20 and ULSD were dominated by C₉ to C₁₆n-alkanes and low levels of the aromatics, and the two fuels had similar headspace vapor composition and concentrations. While the headspace composition predicted using vapor-liquid equilibrium theory was closely correlated to measurements, E85 vapor concentrations were underpredicted. Based on variance decomposition analyses, gasoline and diesel fuels and their vapors VOC were distinct, but B20 and ULSD fuels and vapors were highly collinear. These results can be used to estimate fuel related emissions and exposures, particularly in receptor models that apportion emission sources, and the collinearity analysis suggests that gasoline- and diesel-related emissions can be distinguished.     

Characterisation of particulate matter and gaseous emissions from a large ship diesel engine

Composition of exhaust from a ship diesel engine using heavy fuel oil (HFO) was investigated onboard a large cargo vessel. The emitted particulate matter (PM) properties related to environmental and health impacts were investigated along with composition of the gas-phase emissions. Mass, size distribution, chemical composition and microphysical structure of the PM were investigated. The emission factor for PM was 5.3 g (kg fuel)^?1. The mass size distribution showed a bimodal shape with two maxima: one in the accumulation mode with mean particle diameter D_P around 0.5 μm and one in the coarse mode at D_P around 7 μm. The PM composition was dominated by organic carbon (OC), ash and sulphate while the elemental carbon (EC) composed only a few percent of the total PM. Increase of the PM in exhaust upon cooling was associated with increase of OC and sulphate. Laser analysis of the adsorbed phase in the cooled exhaust showed presence of a rich mixture of polycyclic aromatic hydrocarbon (PAH) species with molecular mass 178–300 amu while PM collected in the hot exhaust showed only four PAH masses.Microstructure and elemental analysis of ship combustion residuals indicate three distinct morphological structures with different chemical composition: soot aggregates, significantly metal polluted; char particles, clean or containing minerals; mineral and/or ash particles. Additionally, organic carbon particles of unburned fuel or/and lubricating oil origin were observed. Hazardous constituents from the combustion of heavy fuel oil such as transitional and alkali earth metals (V, Ni, Ca, Fe) were observed in the PM samples.Measurements of gaseous composition in the exhaust of this particular ship showed emission factors that are on the low side of the interval of global emission factors published in literature for NO_x, hydrocarbons (HC) and CO.     

Empirical Validation of Turbine Engine Exhaust Measurements

The reliability and validity of gas turbine engine exhaust measurements are of concern to all who measure these effluents. In the past, one measure of reliability has been a carbon balance between the fuel used and the C, CO, hydrocarbons, and CO₂ emitted which requires that a F/A ratio be known accurately and that the analyzed sample be representative. In addition to this carbon balance, we have considered the relationships between the concentrations of the several component species. For example, the plot of volume percent of CO₂ versus the volume percent of O₂, both properly corrected to complete combustion, is a straight line. The intercept on the Y-axis (zero oxygen) is a function of the H to C mole ratio in the fuel. This relation has been theoretically established and also established by empirical calculations. For all valid measurements, all points corresponding to CO₂ and O₂ analyses fall on the straight line. In addition, smooth functional relationships exist between other exhaust gas constituents as well, although the form is not a simply derivable linear relationship like that for O₂-CO₂. We have found it useful to employ the following correlations: CO₂ vs. log NO_x, log CO vs. log THC, log CO vs. CO₂, and log THC vs. CO₂- These relationships serve to indicate the probability of reliable data and point out sampling problems and instrument problems such as drift. Subtle changes in engine operation such as opening of the accessory bleed ports in the compressor discharge of the engine can be detected.

The use of a combination of these curves can serve to indicate which measurement is in error. If the O₂-CO₂ relation is linear and the CO-CO₂ relation is smooth, then problems with the total hydrocarbon analyses are indicated when the CO-THC relation is erratic. This would be confirmed by a similar CO₂-THC plot. No useful smooth relationship between smoke density measurements and the other constituents has been found to date. This may indicate poor data, lack of sufficient data, or possibly no correlation.     

Assessment of reducing ozone forming potential for vehicles using liquefied petroleum gas as an alternative fuel

Liquefied petroleum gas (LPG) is currently used in a small fleet of taxis as an alternative fuel to gasoline in Taipei, Taiwan as part of an incentive program promoted by Taiwan EPA to improve urban air quality. Under the test procedure in accordance with the US FTP-75 protocol to simulate an average urban driving pattern, the exhaust from four LPG and four gasoline-powered vehicles was analyzed for the percent composition of NMHCs. Emission factors for individual NMHCs were apportioned from the emission factors of total hydrocarbon based on chemical composition of the exhaust from both types of vehicles. After adjusting for ozone formation potential (OFP) by maximum incremental reactivity, the average OFP for LPG vehicles was estimated to be only 52.8% (g-O₃/veh-km) of the gasoline vehicles, or 3.3% of ozone reduction in Taipei metropolitan area, should all taxis be converted to LPG fuel.Composition analysis of the local LPG revealed that propane, butane and isobutane were the three major components and negligible amounts of alkenes were also found. In addition, the leakage from a LPG service station was substantially smaller than from a gasoline service station because of the closed design with the LPG pumping systems.     

Variability in the primary emissions and secondary gas and particle formation from vehicles using bioethanol mixtures

Bioethanol for use in vehicles is becoming a substantial part of global energy infrastructure because it is renewable and some emissions are reduced. Carbon monoxide (CO) emissions and total hydrocarbons (THC) are reduced, but there is still controversy regarding emissions of nitrogen oxides (NO_x), aldehydes, and ethanol; this may be a concern because all these compounds are precursors of ozone and secondary organic aerosol (SOA). The amount of emissions depends on the ethanol content, but it also may depend on the engine quality and ethanol origin. Thus, a photochemical chamber was used to study secondary gas and aerosol formation from two flex-fueled vehicles using different ethanol blends in gasoline. One vehicle and the fuel used were made in the United States, and the others were made in Brazil. Primary emissions of THC, CO, carbon dioxide (CO₂), and nonmethane hydrocarbons (NMHC) from both vehicles decreased as the amount of ethanol in gasoline increased. NO_x emissions in the U.S. and Brazilian cars decreased with ethanol content. However, emissions of THC, CO, and NO_x from the Brazilian car were markedly higher than those from the U.S. car, showing high variability between vehicle technologies. In the Brazilian car, formation of secondary nitrogen dioxide (NO₂) and ozone (O₃) was lower for higher ethanol content in the fuel. In the U.S. car, NO₂ and O₃ had a small increase. Secondary particle (particulate matter [PM]) formation in the chamber decreased for both vehicles as the fraction of ethanol in fuel increased, consistent with previous studies. Secondary to primary PM ratios for pure gasoline is 11, also consistent with previous studies. In addition, the time required to form secondary PM is longer for higher ethanol blends. These results indicate that using higher ethanol blends may have a positive impact on air quality.

Implications: The use of bioethanol can significantly reduce petroleum use and greenhouse gas emissions worldwide. Given the extent of its use, it is important to understand its effect on urban pollution. There is a controversy on whether there is a reduction or increase in PM emission when using ethanol blends. Primary emissions of THC, CO, CO₂, NO_x, and NMHC for both cars decreased as the fraction of ethanol in gasoline increased. Using a photochemical chamber, the authors have found a decrease in the formation of secondary particles and the time required to form secondary PM is longer when using higher ethanol blends.     

Quantification of gasoline-ethanol blend emissions effects

ABSTRACT

Emissions levels from current gasoline spark-ignited engines are low, and emissions changes associated with the blending of ethanol into gasoline are small and difficult to quantify. Addition of ethanol, with a high blending octane number, allows a reduction in aromatics in market gasoline. Blending behavior of ethanol is nonlinear, altering the distillation curve, including the 50% temperature point, T50. Increase in gasoline direct injection (GDI) engine technology in the fleet challenges ability of older models based on port fuel injection (PFI) results to predict the overall air quality impact of ethanol blending. Five different models derived from data collected through U.S. Environmental Protection Agency Energy Policy Act (EPAct) programs were used to predict LA92 Phase 1 particulate matter (PM) emissions for summer regular (SR) E0 (gasoline with 0% ethanol by volume), E10 (gasoline with 10% ethanol) and E15 (gasoline with 15% ethanol). Substantial reductions of PM for E10 and E15 relative to E0 were predicted when aromatics were displaced by ethanol to maintain octane rating. SR E0 and E10 were also matched to linear combinations of EPAct fuels and results showed a 35% PM reduction for SR E10 relative to SR E0. For GDI vehicles the Coordinating Research Council (CRC) E-94-3 study found that E10 had 23% or 29% PM increase. However, CRC E-129 found an E10 PM reduction of 10% when one E0 fuel and its splash blended (SB) E10 were compared. Both CRC project E-129 SB data and fuel triplets selected from the EPAct study showed variation for E15 emissions, although E-129 suggests that E15 in GDI offers about a 25% reduction of PM with respect to E0. Overall, data suggest that ethanol blending offers a modest to a substantial reduction of cold-start PM mass if aromatic levels of the finished products are reduced in response to ethanol addition.

Implications: Studies of exhaust emissions effects of ethanol blending with gasoline vary in conclusions. Blending properties are nonlinear. Modeling of real-world emissions effects must consider all fuel composition adjustments and property changes associated with ethanol addition. Aromatics are reduced in E10 or E15, compared with E0, and distillation changes. PFI-derived models show reductions in cold-start PM for expected average E10 versus E0 pump fuel, due to reduced aromatic content. Relative emissions effects from older technology (PFI) engines do not predict newer engine (GDI) results reliably, but recent GDI data show reduced cold-start PM when ethanol displaces aromatics.     

Diurnal and Weekday Variations in the Source Contributions of Ozone Precursors in California’s South Coast Air Basin

Abstract

For at least 30 years, ozone (O₃) levels on weekends in parts of California’s South Coast (Los Angeles) Air Basin (SoCAB) have been as high as or higher than on weekdays, even though ambient levels of O₃ precursors are lower on weekends than on weekdays. A field study was conducted in the Los Angeles area during fall 2000 to test whether proposed relationships between emission sources and ambient nonmethane hydrocarbon (NMHC) and oxides of nitrogen (NO_x) levels can account for observed diurnal and day-of-week variations in the concentration and proportions of precursor pollutants that may affect the efficiency and rate of O₃ formation. The contributions to ambient NMHC by motor vehicle exhaust and evaporative emissions, estimated using chemical mass balance (CMB) receptor modeling, ranged from 65 to 85% with minimal day-of-week variation. Ratios of ambient NO_x associated with black carbon (BC) to NO_x associated with carbon monoxide (CO) were approximately 1.25 ± 0.22 during weekdays and 0.76 ± 0.07 and 0.52 ± 0.07 on Saturday and Sunday, respectively. These results demonstrate that lower NO_x emissions from diesel exhaust can be a major factor causing lower NO_x mixing ratios and higher NMHC/NO_x ratios on weekends. Nonmobile sources showed no significant day-of-week variations in their contributions to NMHC. Greater amounts of gasoline emissions are carried over on Friday and Saturday evenings but are, at most, a minor factor contributing to higher NMHC/NO_x ratios on weekend mornings.     

Polycyclic aromatic hydrocarbon exhaust emissions from different reformulated diesel fuels and engine operating conditions

The study of light-duty diesel engine exhaust emissions is important due to their impact on atmospheric chemistry and air pollution. In this study, both the gas and the particulate phase of fuel exhaust were analyzed to investigate the effects of diesel reformulation and engine operating parameters. The research was focused on polycyclic aromatic hydrocarbon (PAH) compounds on particulate phase due to their high toxicity. These were analyzed using a gas chromatography–mass spectrometry (GC–MS) methodology.Although PAH profiles changed for diesel fuels with low-sulfur content and different percentages of aromatic hydrocarbons (5–25%), no significant differences for total PAH concentrations were detected. However, rape oil methyl ester biodiesel showed a greater number of PAH compounds, but in lower concentrations (close to 50%) than the reformulated diesel fuels. In addition, four engine operating conditions were evaluated, and the results showed that, during cold start, higher concentrations were observed for high molecular weight PAHs than during idling cycle and that the acceleration cycles provided higher concentrations than the steady-state conditions. Correlations between particulate PAHs and gas phase products were also observed.The emission of PAH compounds from the incomplete combustion of diesel fuel depended greatly on the source of the fuel and the driving patterns.