Effects of Fuel Type,Driving Cycle,and Emission Status on In-Use Vehicle Exhaust Reactivity

ABSTRACT

The introduction of reformulated gasolines significantly reduced exhaust hydrocarbon (HC) mass emissions, but few data are available concerning how these new fuels affect exhaust reactivity. Similarly, while it is well established that high-emitting vehicles contribute a significant portion of total mobile source HC mass emissions, it is also important to evaluate the exhaust reactivity from these vehicles. The objective of this study was to evaluate the relative influence on in-use vehicle exhaust reactivity of three critical factors: fuel, driving cycle, and vehicle emission status. Nineteen in-use vehicles were tested with seven randomly assigned fuel types and two driving cycles: the Federal Test Procedure (FTP) and the Unified Cycle (UC). Total exhaust reactivity was not statistically different between the FTP and UC cycles but was significantly affected by fuel type. On average, the exhaust reactivity for California Phase 2 fuel was the lowest (16 % below the highest fuel type) among the seven fuels tested for cold start emissions. The average exhaust reactivity for high-emitting vehicles was significantly higher for hot stabilized (11%) and hot start (15%) emissions than for low-emitting vehicles. The exhaust reactivities for the FTP and UC cycles for light-end HCs and carbonyls were significantly different for the hot stabilized mode. There was a significant fuel effect on the mean specific reactivity (SR) for the mid-range HCs, but not for light-end HCs or carbonyls, while vehicle emission status affected the mean SR for all three HC compound classes.     

On-road remote sensing measurements and fuel-based motor vehicle emission inventory in Hangzhou,China

Motor vehicles are one of the largest sources of air pollutants worldwide. Despite their importance, motor vehicle emissions are inadequately understood and quantified, esp. in developing countries. In this study, the real-world emissions of carbon monoxide (CO), hydrocarbons (HC) and nitrogen oxide (NO) were measured using an on-road remote sensing system at five sites in Hangzhou, China in 2004 and 2005. Average emission factors of CO, HC and NO_x for petrol vehicles of different model year, technology class and vehicle type were calculated in grams of pollutant per unit of fuel use (g l⁻¹) from approximately 32,260 petrol vehicles. Because the availability of data used in traditional on-road mobile source estimation methodologies is limited in China, fuel-based approach was implemented to estimate motor vehicle emissions using fuel sales as a measure of vehicle activity, and exhaust emissions factors from remote sensing measurements. The fuel-based exhaust emission inventories were also compared with the results from the recent international vehicle emission (IVE) model. Results show that petrol vehicle fleet in Hangzhou has significantly high CO emissions, relatively high HC and low NO_x, with the average emission factors of 193.07±15.63, 9.51±2.40 and 5.53±0.48 g l⁻¹, respectively. For year 2005 petrol vehicles exhaust emissions contributed with 182,013±16,936, 9107±2255 and 5050±480 metric ton yr⁻¹ of CO, HC and NO_x, respectively. The inventories are 45.5% higher, 6.6% higher and 53.7% lower for CO, HC and NO_x, respectively, than the estimates using IVE travel-based model. In addition, a number of insights about the emission distributions and formation mechanisms have been obtained from an in-depth analysis of these results.     

Generation and Characterization of Diesel Exhaust in a Facility for Controlled Human Exposures

Abstract

An idling medium-duty diesel truck operated on ultralow sulfur diesel fuel was used as an emission source to generate diesel exhaust for controlled human exposure. Repeat tests were conducted on the Federal Test Procedure using a chassis dynamometer to demonstrate the reproducibility of this vehicle as a source of diesel emissions. Exhaust was supplied to a specially constructed exposure chamber at a target concentration of 100 µg · m^-3 diesel particulate matter (DPM). Spatial variability within the chamber was negligible, whereas emission concentrations were stable, reproducible, and similar to concentrations observed on the dynamometer. Measurements of nitric oxide, nitrogen dioxide, carbon monoxide, particulate matter (PM), elemental and organic carbon, carbonyls, trace elements, and polycyclic aromatic hydrocarbons were made during exposures of both healthy and asthmatic volunteers to DPM and control conditions. The effect of the so-called “personal cloud” on total PM mass concentrations was also observed and accounted for. Conventional lung function tests in 11 volunteer subjects (7 stable asthmatic) did not demonstrate a significant change after 2-hr exposures to diesel exhaust. In summary, we demonstrated that this facility can be effectively and safely used to evaluate acute responses to diesel exhaust exposure in human volunteers.     

Speciated Hydrocarbon and Carbon Monoxide Emissions from an Internal Combustion Engine Operating on Methyl Tertiary Butyl Ether-Containing Fuels

ABSTRACT

In the present work, engine and tailpipe (after a three-way catalytic converter) emissions from an internal combustion engine operating on two oxygenated blend fuels [containing 2 and 11% weight/weight (w/w) methyl tertiary butyl ether (MTBE)] and on a nonoxygenated base fuel were characterized. The engine (OPEL 1.6 L) was operated under various conditions, in the range of 0-20 HP. Total unburned hydrocarbons, carbon monoxide, methane, hexane, ethylene, acetaldehyde, acetone, 2-propanol, benzene, toluene, 1,3-butadiene, acetic acid, and MTBE were measured at each engine operating condition. As concerns the total HC emissions, the use of MTBE was beneficial from 1.90 to 3.81 HP, which were by far the most polluting conditions. Moreover, CO emissions in tailpipe exhaust were decreased in the whole operation range with increasing MTBE in the fuel.

The greatest advantage of MTBE addition to gasoline was the decrease in ethylene, acetaldehyde, benzene, toluene, and acetic acid emissions in engine exhaust, especially when MTBE content in the fuel was increased to 11% w/w. In tailpipe exhaust, the catalyst operation diminished the observed differences. Ethylene, methane,and acetaldehyde were the main compounds present in exhaust gases. Ethylene was easily oxidized over the catalyst,while acetaldehyde and methane were quite resistant to oxidation.     

Speciated Hydrocarbon Emissions from the Combustion of Single Component Fuels. II. Catalyst Effects

Six single-component fuels (isooctane, n-heptane, 1-hexene, cyclohexane, methyl-t-butyl ether (MTBE), and toluene) and a multicomponent tracer fuel were burned in a pulse flame combustor (PFC) and reacted over a three-way automotive catalyst. The composition of the raw, uncatalyzed PFC exhaust was characterized in Part I of this study. In Part II, we focus on the conversions of the individual exhaust HC species over the catalyst. In accord with previous studies, the order of reactivity observed for the various classes of HC species was: methane (least reactive) < saturated HC < aromatics < unsaturated HC (most reactive). These differences in catalytic reactivity led to increases in the relative concentrations of methane and some saturated hydrocarbons in the post catalyst exhaust, and corresponding decreases in the relative concentrations of aromatic and unsaturated hydrocarbons. Oxygenated organic compounds showed wide variability in catalytic reactivity depending on the specific compounds involved. Catalytic conversion of the air toxic, 1,3-butadiene, was essentially complete to within detection limits. Benzene and toluene appeared to have similar intrinsic catalytic reactivities. However, net conversion of benzene in most instances was significantly less than that of toluene owing to demethylation of toluene (to form benzene) occurring in parallel with benzene oxidation. Rich combustion of both isooctane and tracer fuel led to the production of methane by the catalyst, primarily from reactions of acetylene and small olefins.     

The Formation of Mg3Ca(S04)4 during the Sulfation Reaction of Dolomite

Abstract

Inspection and maintenance programs for motor vehicles in the United States increasingly use loaded mode mass emissions testing (IM240). A method was developed to predict mass emission rates and mass emission changes, particularly from repair benefits, using a low-cost, portable four-gas non-dispersive infrared (NDIR) vehicle exhaust gas analyzer. A single vehicle was tested several times with the analyzer while on the dynamometer and undergoing successive repairs. Excellent correlations for CO and HC were observed. Five vehicles were measured using an on-road driving loop before and after emissions-related repairs, while another three vehicles were tested with no repairs performed. The on-road concentration data used to guide the repair process were converted to grams per gallon; when divided by estimated miles per gallon, this gave grams per mile emissions for comparison to IM240. Correlation coefficients (r²) of 0.87 for CO and 0.76 for HC were achieved for the 13 tests. The linear correlations between IM240 and emissions measured by this method would allow repair facilities to perform a relatively inexpensive test for diagnostic purposes and to estimate repair effectiveness without the need for a dynamometer.     

大型城市客车加速模拟工况排放特性的实验研究

通过对258辆大型城市客车进行加速模拟工况排放测试,研究了城市客车的排放特性,比较了压缩天然气(CNG)车辆与汽油车辆的排放特性,分析了车辆车龄与排放的关系、发动机燃油供给方式与排放的关系,以及车辆总质量与排放的关系。研究结果表明：燃用CNG的车辆其CO、NOx排放较汽油低许多,尤其是CO,但HC排放较汽油高;电喷车辆的CO、NOx排放比化油器车低,但HC排放值高于化油器车;车龄增长,车辆的CO、NOx排放值增大,但HC变化不明显;车辆总质量增加,排放呈下降趋势。     

Multispecies remote sensing measurements of vehicle emissions on Sherman Way in Van Nuys,California

As part of the 2010 Van Nuys tunnel study, researchers from the University of Denver measured on-road fuel-specific light-duty vehicle emissions from nearly 13,000 vehicles on Sherman Way (0.4 miles west of the tunnel) in Van Nuys, California, with its multispecies Fuel Efficiency Automobile Test (FEAT) remote sensor a week ahead of the tunnel measurements. The remote sensing mean gram per kilogram carbon monoxide (CO), hydrocarbon (HC), and oxide of nitrogen (NO_x) measurements are 8.9% lower, 41% higher, and 24% higher than the tunnel measurements, respectively. The remote sensing CO/NO_x and HC/NO_x mass ratios are 28% lower and 20% higher than the comparable tunnel ratios. Comparisons with the historical tunnel measurements show large reductions in CO, HC, and NO_x over the past 23 yr, but little change in the HC/NO_x mass ratio since 1995. The fleet CO and HC emissions are increasingly dominated by a few gross emitters, with more than a third of the total emissions being contributed by less than 1% of the fleet. An example of this is a 1995 vehicle measured three times with an average HC emission of 419 g/kg fuel (two-stroke snowmobiles average 475 g/kg fuel), responsible for 4% of the total HC emissions. The 2008 economic downturn dramatically reduced the number of new vehicles entering the fleet, leading to an age increase (>1 model year) of the Sherman Way fleet that has increased the fleet's ammonia (NH₃) emissions. The mean NH₃ levels appear little changed from previous measurements collected in the Van Nuys tunnel in 1993. Comparisons between weekday and weekend data show few fleet differences, although the fraction of light-duty diesel vehicles decreased from the weekday (1.7%) to Saturday (1.2%) and Sunday (0.6%).

Implications: On-road remote sensing emission measurements of light-duty vehicles on Sherman Way in Van Nuys, California, show large historical emission reductions for CO and HC emissions despite an older fleet arising from the 2008 economic downturn. Fleet CO and HC emissions are increasingly dominated by a few gross emitters, with a single 1995 vehicle measured being responsible for 4% of the entire fleet's HC emissions. Finding and repairing and/or scrapping as little as 2% of the fleet would reduce on-road tailpipe emissions by as much as 50%. Ammonia emissions have locally increased with the increasing fleet age.     

Speciated Hydrocarbon Emissions from the Combustion of Single Component Fuels. I. Effect of Fuel Structure

Speciated hydrocarbon emissions data have been collected for six single-component fuels run in a laboratory pulse flame combustor (PFC). The six fuels include n-heptane, isooctane (2, 2, 4-trimethylpentane), cyclohexane, 1-hexene, toluene, and methyl-t-butyl ether (MTBE: an oxygenated fuel extender). Combustion of non-aromatic fuels in the PFC (at a fuel/air equivalence ratio of Φ = 1.02) produced low levels of unburned fuel and high yields of methane and olefins (> 75 percent combined) irrespective of the molecular structure of the fuel. In contrast, hydrocarbon emissions from toluene combustion in the PFC were comprised predominantly of unburned fuel (72 percent). With the PFC, low levels of 1, 3-butadiene (0.3-1.8 percent) were observed from all the fuels except MTBE, for which no measurable level (<0.2 percent) was detected; low levels of benzene were observed from isooctane, heptane, and 1-hexene, but significant levels (9 percent) from cyclohexane and toluene. No measurable amount of benzene (< 0.2 percent) was observed in the MTBE exhaust.

For isooctane and toluene the speciated hydrocarbon emissions from a spark-ignited (SI) single-cylinder engine were also determined. HC emissions from the SI engine contained the same species as observed from the PFC, although the relative composition was different. For the non-aromatic fuel isooctane, unburned fuel represented a larger fraction (50 percent) of the HC emissions when run in the engine. HC emissions from toluene combustion in the engine were similar to those from the PFC.     

Emissions from Carbureted and Timed Port Fuel Injected Engines

A comparison was made between the exhaust emission characteristics of a popular make car when equipped with the stock carburetor and when equipped with a timed-port fuel injection system. A brief optimization study was made to adjust the spark timing and fuel flow characteristics to minimize emissions. Performance and economy were compared between the fuel injected and carbureted versions. Emission measurements of CO, CO₂, and hydrocarbon were made in road tests by proportional sampling and through the California Cycle by continuous nondispersive infra red instrumentation.     

A Fuel-Based Motor Vehicle Emission Inventory

Abstract

A fuel-based methodology for calculating motor vehicle emission inventories is presented. In the fuel-based method, emission factors are normalized to fuel consumption and expressed as grams of pollutant emitted per gallon of gasoline burned. Fleet-average emission factors are calculated from the measured on-road emissions of a large, random sample of vehicles. Gasoline use is known at the state level from sales tax data, and may be disaggregated to individual air basins. A fuel-based motor vehicle CO inventory was calculated for the South Coast Air Basin in California for summer 1991. Emission factors were calculated from remote sensing measurements of more than 70,000 in-use vehicles. Stabilized exhaust emissions of CO were estimated to be 4400 tons/day for cars and 1500 tons/day for light-duty and medium- duty trucks, with an estimated uncertainty of ±20% for cars and ±30% for trucks. Total motor vehicle CO emissions, including incremental start emissions and emissions from heavy-duty vehicles were estimated to be 7900 tons/day. Fuelbased inventory estimates were greater than those of California's MVEI 7F model by factors of 2.2 for cars and 2.6 for trucks. A draft version of California's MVEI 7G model, which includes increased contributions from high-emitting vehicles and off-cycle emissions, predicted CO emissions which closely matched the fuel-based inventory. An analysis of CO mass emissions as a function of vehicle age revealed that cars and trucks which were ten or more years old were responsible for 58% of stabilized exhaust CO emissions from all cars and trucks.     

Emissions from Slash Burning and the Influence of Flame Retardant Chemicals

Pollutants sampled during the burning of 30 lb ponderosa pine fuel beds yielded emission factors for CO, hydrocarbon gases, and par-ticulate matter of 146, 8.4, and 9.1 lb/ton of fuel, respectively. When similar beds were treated with diammonium phosphate flame retardant, these factors increased to 166, 11.7, and 19.3 lb/ton of fuel, respectively.

Gas chromatographic analysis of hydrocarbon gases showed that 15-40% of this material was composed of methane and eth-ylene. Ethane and acetylene were the next most abundant materials, with photochemically important materials constituting minor portions of this gaseous component. Fuel beds treated with flame retardant produced more oiefins, and this production lasted throughout the smoldering phase of burning.

These tests showed that the smoldering phase of combustion is of major importance to air pollutant production during slash burning. The initial 80% of the fuel burned accounted for only 20-30% of HC and CO emissions. This suggests that a rapid mop-up of slash burns could substantially reduce air pollutant production.     

Emissions profile from new and in-use handheld, 2-stroke engines

The objective of this study was to characterize exhaust emissions from a series of handheld, 2-stroke small engines. A total of 23 new and used engines from model years 1981–2003 were studied; these engines spanned three phases of emission control (pre-control, phase-1, phase-2). Measured emissions included carbon monoxide (CO), carbon dioxide (CO₂), nitrogen oxides (NO_x), hydrocarbons (HC), fine particulate matter (PM_2.5), and sulfur dioxide (SO₂). Emissions reductions in CO (78%) and HC (52%) were significant between pre-control and phase-2 engines. These reductions can be attributed to improvements in engine design, reduced scavenging losses, and implementation of catalytic exhaust control. Total hydrocarbon emissions were strongly correlated with fuel consumption rates, indicating varying degrees of scavenging losses during the intake/exhaust stroke. The use of a reformulated gasoline containing 10% ethanol resulted in a 15% decrease in HC and a 29% decrease in CO emissions, on average. Increasing oil content of 2-stroke engine fuels results in a substantial increase of PM_2.5 emissions as well as smaller increases in HC and CO emissions. Results from this study enhance existing emission inventories and appear to validate predicted improvements to ambient air quality through implementation of new phase-2 handheld emission standards.     

Hydrocarbon emission fingerprints from contemporary vehicle/engine technologies with conventional and new fuels

The present paper presents results from the analysis of 29 individual C₂–C₉ hydrocarbons (HCs) specified in the European Commission Ozone Directive. The 29 HCs are measured in exhaust from common, contemporary vehicle/engine/fuel technologies for which very little or no data is available in the literature. The obtained HC emission fingerprints are compared with fingerprints deriving from technologies that are being phased out in Europe. Based on the total of 138 emission tests, thirteen type-specific fingerprints are extracted (Mean ± SD percentage contributions from individual HCs to the total mass of the 29 HCs), essential for receptor modelling source apportionment. The different types represent exhaust from Euro3 and Euro4 light-duty (LD) diesel and petrol-vehicles, Euro3 heavy-duty (HD) diesel exhaust, and exhaust from 2-stroke preEuro, Euro1 and Euro2 mopeds. The fuels comprise liquefied petroleum gas, petrol/ethanol blends (0–85% ethanol), and mineral diesel in various blends (0–100%) with fatty acid methyl esters, rapeseed methyl esters palm oil methyl esters, soybean oil methyl or sunflower oil methyl esters. Type-specific tracer compounds (markers) are identified for the various vehicle/engine/fuel technologies.An important finding is an insignificant effect on the HC fingerprints of varying the test driving cycle, indicating that combining HC fingerprints from different emission studies for receptor modelling purposes would be a robust approach.The obtained results are discussed in the context of atmospheric ozone formation and health implications from emissions (mg km^?1 for LD and mopeds and mg kW h^?1 for HD, all normalised to fuel consumption: mg dm^?3 fuel) of the harmful HCs, benzene and 1,3-butadiene.Another important finding is a strong linear correlation of the regulated “total” hydrocarbon emissions (tot-HC) with the ozone formation potential of the 29 HCs (ΣPO₃ = (1.66 ± 0.04) × tot-RH; r² = 0.93). Tot-HC is routinely monitored in emission control laboratories, whereas C₂–C₉ are not. The revealed strong correlations broadens the usability of data from vehicle emission control laboratories and facilitates the comparison of the ozone formation potential of HCs in exhaust from of old and new vehicle/engine/fuel technologies.     

The Prediction of the Rise of a Hot Cloud from Field Experiments

The rise of a hot cloud resulting from combustion of a solid propellant rocket fuel at ground level has been determined from lapse-time movies and visual aircraft observations. The field tests were conducted near the 420 foot meteorological tower under various atmospheric conditions. A method of predicting the maximum thermal rise of a cloud, based on source and meteorological parameters, is described. Comparisons with other theoretical formulations are presented.     

Product Guide/1970

Abstract

In Mexico City, the use and composition of fuels determine that carbon monoxide (CO) comes mostly from mobile sources, and sulfur dioxide (SO₂) from fixed and mobile sources. By simultaneously measuring hydrocarbons (HC), CO, and SO₂ in the atmosphere of Mexico City, the relative amounts coming from different sources can be estimated. Assuming that some HC are emitted proportionally to CO emissions, we can establish that [HC]₁= m1? [CO], where the proportionality constant ml corresponds to the ratio of emissions factor for HC and CO in mobile sources. Similarly for fuels containing sulfur, it can be assumed that [HC]₂ = m2 ? [SO₂]. In this way, the total HC are [HC]_total=[HC]₀+ ml ? [CO]+ m2 ? [SO₂], where [HC]₀ corresponds mainly to other sources like solvent evaporation, gas consumption, and natural emissions. In this way, it can be estimated that in Mexico City 75% of average HC comes from mobile sources, 5% from sulfur-related sources, and 19% from natural sources and solvent evaporation. Compared with the HC/CO ratio measured in the exhaust pipe of vehicles, we estimated that 70% of HC emitted from mobile sources are evaporative losses, and only 30% come through the exhaust system.     

Improvement of Air Quality in a Small Indoor Ice Arena by Effective Emission Control in Ice Resurfacers

ABSTRACT

The effectiveness of a new emission control system in the ice resurfacer was tested in an exhaust gas emission laboratory, and the improvement of the air quality in a small, enclosed ice arena was demonstrated in a 4.5-month follow-up study. The emission control system consisted of a lambda sensor-controlled fuel supply and a three-way metallic catalyst that were applied to a propane-fueled resurfacer. In the laboratory tests, the engine emissions of carbon monoxide (CO), hydrocarbons (HC), and nitrogen oxides (NO ) reduced simultaneously by 91, 90, and 96%, respectively. During the air quality follow-up the median 1-hour average nitrogen dioxide (N0₂) concentration inside the ice arena decreased from 430 ug/m³ (230ppb) to 58 ug/m³ (31 ppb), and that of CO decreased from 4.4 mg/m³ (3.8 ppm) to 1.5 mg/m³ (1.3 ppm). The new emission control system proved to be a feasible, reliable, and effective means to improve the indoor air quality in the ice arena. However, continuous mechanical ventilation was necessary during all business hours in order to achieve and maintain a fully acceptable air quality with this technology.     

Cumulus cloud transport,scavenging and chemistry: Observations and simulations

Observational and numerical investigations of cumulus cloud scavenging, transport and chemical processes are presented. The experimental data set includes surface and aircraft measurements of the chemistry and microphysics of aerosol, cloud and precipitation. To help in the interpretation of these experimental data fully three-dimensional simulations of cloud chemistry and scavenging are performed. After adjusting several unmeasured model parameters, reasonable agreement could be obtained between the simulated and observed cloud chemistry and aerosol distribution in clouds. The rate at which the simulated clouds transported and transformed pollutants did not exceed a few per cent per hour.     

Idle Emissions from Heavy-Duty Diesel Vehicles: Review and Recent Data

Abstract

Heavy-duty diesel vehicle idling consumes fuel and reduces atmospheric quality, but its restriction cannot simply be proscribed, because cab heat or air-conditioning provides essential driver comfort. A comprehensive tailpipe emissions database to describe idling impacts is not yet available. This paper presents a substantial data set that incorporates results from the West Virginia University transient engine test cell, the E-55/59 Study and the Gasoline/Diesel PM Split Study. It covered 75 heavy-duty diesel engines and trucks, which were divided into two groups: vehicles with mechanical fuel injection (MFI) and vehicles with electronic fuel injection (EFI). Idle emissions of CO, hydrocarbon (HC), oxides of nitrogen (NO_x), particulate matter (PM), and carbon dioxide (CO₂) have been reported. Idle CO₂ emissions allowed the projection of fuel consumption during idling. Test-to-test variations were observed for repeat idle tests on the same vehicle because of measurement variation, accessory loads, and ambient conditions. Vehicles fitted with EFI, on average, emitted [~20 g/hr of CO, 6 g/hr of HC, 86 g/hr of NO_x, 1 g/hr of PM, and 4636 g/hr of CO₂ during idle. MFI equipped vehicles emitted ~35 g/hr of CO, 23 g/hr of HC, 48 g/hr of NO_x, 4 g/hr of PM, and 4484 g/hr of CO₂, on average, during idle. Vehicles with EFI emitted less idleCO, HC, and PM, which could be attributed to the efficient combustion and superior fuel atomization in EFI systems. Idle NO_x, however, increased with EFI, which corresponds with the advancing of timing to improve idle combustion. Fuel injection management did not have any effect on CO₂ and, hence, fuel consumption. Use of air conditioning without increasing engine speed increased idle CO₂, NO_x, PM, HC, and fuel consumption by 25% on average. When the engine speed was elevated from 600 to 1100 revolutions per minute, CO₂ and NO_x emissions and fuel consumption increased by >150%, whereas PM and HC emissions increased by ~100% and 70%, respectively. Six Detroit Diesel Corp. (DDC) Series 60 engines in engine test cell were found to emit less CO, NO_x, and PM emissions and consumed fuel at only 75%of the level found in the chassis dynamometer data. This is because fan and compressor loads were absent in the engine test cell.     

Effects of diesel/biodiesel blends on regulated and unregulated pollutants from a passenger vehicle operated over the European and the Athens driving cycles

This paper presents the regulated and unregulated exhaust emissions of a diesel passenger vehicle, operated with low sulphur automotive diesel and soy methyl ester blends. Emission and fuel consumption measurements were conducted under real driving conditions (Athens Driving Cycle, ADC) and compared with those of a modified New European Driving Cycle (NEDC) using a chassis dynamometer. A Euro II compliant diesel vehicle was used in this study, equipped with an indirect injection diesel engine, fuelled with diesel fuel and biodiesel blends at proportions of 5, 10, and 20% respectively. Unregulated emissions of 11 polycyclic aromatic hydrocarbons (PAHs), 5 nitro-PAHs, 13 carbonyl compounds (CBCs) and the soluble organic fraction (SOF) of the particulate matter were measured. Qualitative hydrocarbon analysis was also performed on the SOF. Regulated emissions of NO_x, CO, HC, CO₂, and PM were also measured over the two test cycles. It was established that some of the emissions measured over the (hot-start) NEDC differed from the real-world cycle. Significant differences were also observed in the vehicle's fuel consumption between the two test cycles. The addition of biodiesel reduced the regulated emissions of CO, HC and PM, while an increase in NO_x was observed over the ADC. Carbonyl emissions, PAHs and nitro-PAHs were reduced with the addition of biodiesel over both driving cycles.