Comparison of aerobic and anaerobic biotreatment of municipal solid waste

To increase the operating lifetime of landfills and to lower leachate treatment costs, an increasing number of municipal solid waste (MSW) landfills are being managed as either aerobic or anaerobic bioreactors. Landfill gas composition, respiration rates, and subsidence were measured for 400 days in 200-L tanks filled with fresh waste materials to compare the relative effectiveness of the two treatments. Tanks were prepared to provide the following conditions: (1) air injection and leachate recirculation (aerobic), (2) leachate recirculation (anaerobic), and (3) no treatment (anaerobic). Respiration tests on the aerobic wet tank showed a steady decrease in oxygen consumption rates from 1.3 mol/day at 20 days to 0.1 mol/day at 400 days. Aerobic wet tanks produced, on average, 6 mol of carbon dioxide (CO2)/kg of MSW as compared with anaerobic wet tanks, which produced 2.2 mol methane/kg of MSW and 2.0 mol CO2/kg methane. Over the test period, the aerobic tanks settled on average 35%, anaerobic tanks settled 21.7%, and the no-treatment tank settled 7.5%, equivalent to overall mass loss in the corresponding reactors. Aerobic tanks reduced stabilization time and produced negligible odor compared with anaerobic tanks, possibly because of the 2 orders of magnitude lower leachate ammonia levels in the aerobic tank. Both treatment regimes provide the opportunity for disposal and remediation of liquid waste.     

渗滤液回流对不同填埋结构甲烷变化规律的影响研究

建立了大型模拟填埋试验装置,研究了渗滤液回流对不同填埋结构甲烷变化规律的影响.每周对填埋气体中甲烷浓度进行监测.结果表明:厌氧填埋中回流操作使甲烷浓度峰值提前了147 d,峰值为59.6%(体积分数,下同);准好氧填埋中回流操作使甲烷浓度峰值提前259 d,峰值为44.7%.回流操作使甲烷产气高峰提前,增加产气量,加快填埋垃圾稳定,减轻渗滤液污染.厌氧填埋中进行回流操作有利于甲烷的回收利用;准好氧填埋结构可有效减少甲烷的排放,减小对环境的危害.稳定期的垃圾填埋体进行回流产生一定的甲烷,但浓度较低,最高仅26.0%,没有利用价值.     

模拟生物反应器加速产甲烷过程研究

渗滤液原液回灌易导致填埋垃圾产甲烷过程的滞后,从而对甲烷收集利用产生不利影响。通过3根实验室模拟生物反应器,研究了原液回灌(C1)、渗滤液好氧预处理后回灌(C2)和原液回灌+垃圾层上部通风曝气(C3)3种填埋方式下的填埋气产气规律。结果表明,C1甲烷浓度经历短暂上升,达到19.5%后开始逐渐降低,产甲烷速率和产甲烷总量均很低;C2甲烷浓度逐渐上升,在第121天时甲烷浓度达到50%,产甲烷最高速率和产甲烷总量分别为0.31 L/(kg·d)和25.2 L/kg。在停止上部垃圾层通风曝气后,C3甲烷浓度迅速上升,在81 d时甲烷浓度便达到50%以上,最大产甲烷速率和产甲烷总量分别为0.22 L/(kg·d)和16.0 L/kg。对各模拟柱填埋气可回收性评价结果表明,C3填埋气可回收利用比例最高,C2略低,C1在实验期间内则无可回收利用气体产生。     

Biodegradation of organic matters from mixed unshredded municipal solid waste through air convection before landfilling

Landfilling is a dominant municipal solid waste (MSW) disposal method in most developing countries. In China, approximately 85% of the generated MSW is being disposed of in the landfills. The amount of MSW is growing rapidly with the rate of approximately 8-10% annually, which contains a high quantity of moisture and organic matters. The problems of leachate treatment and landfill gas (LFG) emissions are increasing gradually. Reducing the hazard before emplacement, pretreatment of MSW before landfilling has become very important for the conventional landfill. In this study, aerobic pretreatment of mixed MSW was used, and much attention has been given to the natural convection of air in the mixed and unshredded MSW for bioconversion of organic matter (OM). This study is an attempt to investigate aerobic pretreatment suitability for the mixed and unshredded MSW at Beijing. A pilot-scale aerobic pretreatment simulator (APS) was developed at Beishen Shu Landfill in Beijing. To work out the biodegradation of the OM in the APS, fresh and pretreated MSW samples were collected and analyzed for OM, moisture content, temperature, chemical oxygen demand, total organic carbon, carbon, nitrogen, hydrogen, lignocelluloses, and biochemical methane potential at various stages of the pretreatment. Furthermore, results of the fresh and pretreated MSW are compared. Significant reduction in the observed parameters of the pretreated waste samples is observed. This work demonstrates that pretreatment is significantly effective in reducing the landfill emissions that is leachate and LFG.     

渗滤液回灌频率对生物反应器填埋场的影响研究

通过模拟实验研究了渗滤液回灌周期为1、2、3和5 d的4个模拟垃圾柱的产甲烷过程和渗滤液水质的变化情况.在用NaOH调节回灌渗滤液pH值的前提下,回灌频率越高,模拟厌氧型生物反应器填埋垃圾柱先开始产甲烷,但当回灌周期低于3 d时,开始产甲烷的时间相差不多.从渗滤液水质看,回灌周期为3 d的垃圾柱渗滤液COD、VFA等有机污染物浓度下降最快.综合考虑启动时间、运行费用和填埋场的稳定进程,在厌氧型生物反应器填埋场中,实施3 d/次的渗滤液回灌频率最为合适.     

Methane Emissions from Domestic Waste Management Facilities in Jordan—Applicability of IPCC Methodology

ABSTRACT

In this paper, methane emissions from municipal wastewater treatment plants and municipal solid waste (MSW) landfills in Jordan for 1994 have been estimated using the methodology developed by the Intergovernmental Panel on Climate Change (IPCC). For this purpose, the 14 domestic wastewater treatment plants in the country were surveyed. Generation rates and characterization of MSW components as well as dumping and landfilling practices were surveyed in order to estimate 1994 CH₄ emissions from these sites. Locally available waste statistics were used in cases where those of the IPCC guidelines were not representative of Jordan's statistics.

Methane emissions from domestic wastewater in Jordan were estimated at 4.66 gigagrams (Gg). Total 1994 CH₄ emissions from MSW management facilities in Jordan are estimated at 371.76 Gg—351.12 Gg (94.45%) from sanitary landfills, 19.83 Gg (5.33%) from MSW open dumps, and 0.81 Gg (0.22%) from raw sewage-water dumping ponds. Uncertainties associated with these estimations are presented.     

A survey of municipal solid waste landfills in Beijing during 2009–2011

The investigation of municipal solid waste (MSW) treatment in China is rare due to its sensitivity and difficulty in terms of access. We chose Beijing, the capital of China, as an example to identify the characteristics of MSW landfill treatments using a 2-month investigation with 20 participants. MSW landfill treatments account for nearly 70% of the annual MSW disposal in Beijing; the landfill processes are equipped with many kinds of technologies and consume a large amount of energy and produce a variety of contaminants. The cover method (the most obvious difference in landfill tamping) mainly includes high-density polyethylene (HDPE) geomembranes with loess and soil alone (i.e., loess or sandy soil). We investigated the actual conditions of landfills and collected data on leachate and landfill gas (LFG) emissions and energy consumption during 2009–2011. The results indicated that the cover method employed by landfills was related to treatment quantity, operation, and especially landfill location. Early large-scale landfills located in plains were covered with HDPE geomembranes, and newly built landfills covered with soil tended to be equipped with HDPE covers. Using HDPE cover also contributed greatly to LFG production due to its impermeability but had no remarkable effect on leachate yield reduction due to the dry climate in Beijing. The potential was reinforced by the potentials of decrement and reuse. The disposal method of LFG can be optimized, and the power generated by the LFG process can meet the landfill demand. The gray water recycled from the leachate could be used in the landfill process.

     

垃圾填埋场水分迁移模型的应用研究

以渗滤液回灌为核心的填埋场生化反应器是当今国际固体废物研究的新方向 ,其具有减少渗滤液处理难度和加速填埋场稳定化的作用 ,其中控制填埋场水分是关键。本文通过对填埋场水分运移特征的分析 ,建立了渗滤液回灌条件下 ,生化反应器填埋场水分迁移的饱和 -非饱和三维非稳定数学模型 ,并求其有限单元数值解 ,定量模拟和预报不同回灌条件下填埋场水分的时空分布规律并进行实用研究。针对重庆市长生桥卫生填埋场设计情况和实际条件 ,运移模拟模型分析了水平沟和竖式井回灌条件下填埋场内水分的分布规律 ,证明了协同回灌方式的有效性     

城市固体废物好氧生物反应器填埋方式的实验研究

MSW(城市固体废物)生物反应器型填埋是一种较新颖的方法。在系统分析现有填埋方法优缺点的基础上,对其加以改进,将强制通风好氧和渗滤液循环2种方式有机地结合在一起,构建了MSW好氧生物反应器。考察了NH3、CH4、CO2、pH和温度等因素,并监测分析了渗滤液中的COD、BOD5、Zn2+、NH4+和NO3-等指标,旨在研究其中垃圾的降解及渗滤液中COD、BOD5、Zn2+、NH4+和NO3-的去除情况,探讨该生物反应器对垃圾和渗滤液相关参数的作用机理。结果表明,该反应器对渗滤液中COD、BOD5、NO3-的去除率分别达到96.34%、94.58%和99.9%,对其中的Zn2+也有较好的脱除效果。     

回灌对垃圾填埋初期渗滤液化学需氧量的影响

通过模拟柱实验 ,研究了回灌对垃圾填埋场初期渗滤液 CODCr的影响。研究结果表明 ,模拟降雨雨水的渗入且无渗滤液回灌的参照柱 ,其渗滤液出水 CODCr最高 ,一般在 70 0 0 0 mg/L 左右 ;模拟渗滤液原液回灌 ,从第 4周起因脂肪酸的积累导致渗滤液的 p H低于 6,从而抑制了微生物的生化反应 ;模拟好氧生物处理后渗滤液的回灌 ,能加速垃圾层 CODCr的溶出和甲烷化阶段的建立 ,且此时渗滤液的 CODCr变化规律符合指数方程 ;当垃圾层建立甲烷化阶段后 ,回灌 CODCr在 2 0 0 0 0 m g/L 左右的渗滤液 ,仍可促使垃圾中有机物迅速转化为气态物     

Batch test assessment of waste-to-energy combustion residues impacts on precipitate formation in landfill leachate collection systems

Disposal practices for bottom ash and fly ash from waste-to-energy (WTE) facilities include emplacement in ash monofills or co-disposal with municipal solid waste (MSW) and residues from water and wastewater treatment facilities. In some cases, WTE residues are used as daily cover in landfills that receive MSW. A recurring problem in many landfills is the development of calcium-based precipitates in leachate collection systems. Although MSW contains varying levels of calcium, WTE residues and treatment plant sludges have the potential to contribute concentrated sources of leachable minerals into landfill leachates. This study was conducted to evaluate the leachability of calcium and other minerals from residues generated by WTE combustion using residues obtained from three WTE facilities in Florida (two mass-burn and one refuse-derived fuel). Leaching potential was quantified as a function of contact time and liquid-to-solid ratios with batch tests and longer-term leaching tests using laboratory lysimeters to simulate an ash monofill containing fly ash and bottom ash. The leachate generated as a result of these tests had total dissolved solid (TDS) levels ranging from 5 to 320 mg TDS/g ash. Calcium was a major contributor to the TDS values, contributing from 20 to 105 g calcium/kg ash. Fly ash was a major contributor of leachable calcium. Precipitate formation in leachates from WTE combustion residues could be induced by adding mineral acids or through gas dissolution (carbon dioxide or air). Stabilization of residual calcium in fly ashes that are landfilled and/or the use of less leachable neutralization reagents during processing of acidic gases from WTE facilities could help to decrease the calcium levels in leachates and help to prevent precipitate formation in leachate collection systems.     

接种比对餐厨垃圾干式厌氧发酵启动的影响

针对不同接种比对餐厨垃圾干式厌氧发酵启动的影响,对比分析了VS接种比分别为0.36和0.90两种情况下,餐厨垃圾干式厌氧发酵启动过程中pH、NH4-N、COD、VFA、甲烷含量等指标的变化。实验结果表明,启动初期2组样品pH分别快速降至4.74和5.68,均呈酸化状态,经碱液调整后,接种比为0.36的处理仍无法正常产气,接种比为0.90的处理,pH逐步提高,系统正常运行,经72 d的发酵实验,COD去除率达90.29%,甲烷含量高于60%的沼气产量达255.4 L,分析可见,VS接种比是干式厌氧发酵处理的重要参数;此外,与传统湿式厌氧发酵处理相比,餐厨垃圾干式厌氧发酵在较高的VFA和氨氮浓度下,仍能正常运行,采用干式厌氧发酵技术处理餐厨垃圾是可行的。     

A Life-Cycle Inventory Model of Municipal Solid Waste Combustion

ABSTRACT

Evaluation of alternate strategies for municipal solid waste (MSW) management requires models to calculate environmental emissions as a function of both waste quantity and composition. A methodology to calculate waste component-specific emissions associated with MSW combustion is presented here. The methodology considers emissions at a combustion facility as well as those avoided at an electrical energy facility because of energy recovered from waste combustion. Emission factors, in units of kg pollutant per metric ton MSW entering the combustion facility, are calculated for CO₂-biomass, CO₂-fossil, SO_x , HCl, NO_x , dioxins/furans, PM, CO, and 11 metals. Water emissions associated with electrical energy offsets are also considered. Reductions in environmental emissions for a 500-metric-ton-per-day combustion facility that recovers energy are calculated.     

Methane emissions from domestic waste management facilities in Jordan--applicability of IPCC methodology

In this paper, methane emissions from municipal wastewater treatment plants and municipal solid waste (MSW) landfills in Jordan for 1994 have been estimated using the methodology developed by the Intergovernmental Panel on Climate Change (IPCC). For this purpose, the 14 domestic wastewater treatment plants in the country were surveyed. Generation rates and characterization of MSW components as well as dumping and landfilling practices were surveyed in order to estimate 1994 CH4 emissions from these sites. Locally available waste statistics were used in cases where those of the IPCC guidelines were not representative of Jordan's statistics. Methane emissions from domestic wastewater in Jordan were estimated at 4.66 gigagrams (Gg). Total 1994 CH4 emissions from MSW management facilities in Jordan are estimated at 371.76 Gg--351.12 Gg (94.45%) from sanitary landfills, 19.83 Gg (5.33%) from MSW open dumps, and 0.81 Gg (0.22%) from raw sewage-water dumping ponds. Uncertainties associated with these estimations are presented.     

Estimate of the Pollution Removed by Leaching of Standard Domestic Waste: Mass Assessments Carried Out in Batches and Columns

Abstract

Batch and column tests allowed estimation of the mobilization of pollution of standard domestic waste in leachate and biogas. Three laboratory tests (biochemical methane potential (BMP), tank leaching test (TLT), and column tests) have been applied to evaluate the emission of pollutants in liquid and/or gas phase from reconstituted municipal solid waste (MSW) on the basis of French waste. In the case of the batch tests (BMP and TLT), BMP tests indicated a maximum organic carbon share produced by waste (biogas potential) equal to 59% of the initial carbon. The maximum quantity of carbon likely to be leached by the waste (TLT) corresponded to 6% of the carbon contained in the waste. On the other hand, during column tests, 3.3% of carbon was leached and 8% of carbon was evacuated in biogas at the end of a 440-day follow-up. It thus appears that the test conditions have a great in?uence on the remobilization of pollution. In particular it has been proven than the greater the optimization of the liquid/solid ratio, the agitation, the sowing, and the temperature, the greater the pollutant is leached. This study highlights the possible use of batch and column tests to evaluate the pollution risk of a landfill.     

Municipal solid waste management planning for Xiamen City,China: a stochastic fractional inventory-theory-based approach

In this study, a stochastic fractional inventory-theory-based waste management planning (SFIWP) model was developed and applied for supporting long-term planning of the municipal solid waste (MSW) management in Xiamen City, the special economic zone of Fujian Province, China. In the SFIWP model, the techniques of inventory model, stochastic linear fractional programming, and mixed-integer linear programming were integrated in a framework. Issues of waste inventory in MSW management system were solved, and the system efficiency was maximized through considering maximum net-diverted wastes under various constraint-violation risks. Decision alternatives for waste allocation and capacity expansion were also provided for MSW management planning in Xiamen. The obtained results showed that about 4.24 × 10⁶ t of waste would be diverted from landfills when p _i is 0.01, which accounted for 93% of waste in Xiamen City, and the waste diversion per unit of cost would be 26.327 × 10³ t per $10⁶. The capacities of MSW management facilities including incinerators, composting facility, and landfills would be expanded due to increasing waste generation rate.     

Biomineralization rates of 14C-labelled organic chemicals in aerobic and anaerobic suspended soil

The formation of ¹⁴CO₂ from 13 ¹⁴C-labelled organic chemicals in aerobic and anaerobic suspended soil was determined. After 5 days at 35°C, ¹⁴CO₂ was between 70.1% (urea, anaerobic) and < 0.1% (2,6-dichlorobenzonitrile and hexachlorobenzene, aerobic and anaerobic) of the ¹⁴C initially applied.     

垃圾填埋场加速稳定化表征指标的相关性分析

加速稳定化表征指标是生物反应器填埋技术评价的重要内容。通过垃圾填埋室内模拟实验,研究不同运行工况下垃圾挥发性固体(VS)、生物可降解物(BDM)、纤维素(C)和纤维素/木质素(C/L)等组分指标的动态变化规律及其对加速稳定化进程的指示作用,进而探寻各指标之间的相关性,进一步筛选确定垃圾填埋场加速稳定化进程的核心表征指标。结果表明,垃圾组分VS、BDM、C和C/L的衰减符合一级反应动力学,其动态变化能够较为灵敏地指示渗滤液回灌和通风供氧对垃圾稳定化的显著加速作用,可作为垃圾填埋场加速稳定化进程的表征指标。VS、BDM、C和C/L相互之间具有良好的正线性相关性。BDM和C/L适宜作为垃圾填埋场加速稳定化进程的核心表征指标。     

Effect of leachate recirculation on refuse decomposition rates at landfill site: a case study

In this study, a comparison of methane (CH₄) generation rates for two test cells, one operated with (enhanced) and another without leachate recirculation at Odayeri Sanitary Landfill were compared using their bio-chemical methane potentials (BMP). Initial methane potential is approximately 34.5 m3 CH₄/wet ton of solid waste. The remaining methane potential for the control (C1) and the enhanced (C2) cells are 32.6 m3 CH₄/wet ton and 31.1 m3 CH₄/wet ton of refuse after eight months of operation, respectively. The produced CH₄ quantities for C1 and C2 after eight months of operation are 1.9 m3 CH₄/wet ton and 3.4 m3 CH₄/wet ton, respectively. On the other hand, 5.5% and 9.9% of the total potential are generated in eight months. However, the CH₄ generation rates for the first year are determined as 2.85 and 5.10 m3/ton/year for C1 and C2 test cells, respectively. Due to the appropriate conditions such as moisture content, solid waste decomposition rate is enhanced at a rate of 79% at C2 test cell relative to C1 test cell. Hence, C2 test cell shows more decomposition relative to the C1 test cell.     

西南地区某已封场非规范垃圾填埋场垃圾稳定化进程分析

以重庆某非规范填埋场为例,针对西南地区已封场非规范垃圾填埋场的稳定化进程进行了分析。按照场地布局选取4个采样点,在垃圾体上进行钻孔取样,分析不同深度的垃圾样pH值、有机质、含水率、生物可降解度以及垃圾样浸出液和填埋气组成以及各个指标随着填埋深度的变化规律,确定不同深度垃圾体的稳定化程度。结果表明,场内垃圾已呈现矿化垃圾特征;有机质、BDM、浸出液COD以及填埋气CH4含量等4个指标与填埋深度均较好地符合一级降解反应,可以预测垃圾体稳定化临界填埋深度。根据有机质、BDM、浸出液COD以及填埋气CH4含量等4个指标与填埋深度一级降解反应函数预测临界稳定化深度为15 m,与实测值判定的稳定化填埋深度相一致性。在对非规范垃圾填埋场场地利用过程中,需要先对未稳定的上层垃圾进行清理,并在已稳定的底层垃圾体上充填其他稳定介质后利用该地块。