Airborne emissions of mercury from municipal solid waste. I: new measurements from six operating landfills in Florida

Mercury-bearing material enters municipal landfills from a wide array of sources, including fluorescent lights, batteries, electrical switches, thermometers, and general waste; however, the fate of mercury (Hg) in landfills has not been widely studied. Using automated flux chambers and downwind atmospheric sampling, we quantified the primary pathways of Hg vapor releases to the atmosphere at six municipal landfill operations in Florida. These pathways included landfill gas (LFG) releases from active vent systems, passive emissions from landfill surface covers, and emissions from daily activities at each working face (WF). We spiked the WF at two sites with known Hg sources; these were readily detected downwind, and were used to test our emission modeling approaches. Gaseous elemental mercury (Hg(O)) was released to the atmosphere at readily detectable rates from all sources measured; rates ranged from approximately 1-10 ng m(-2) hr(-1) over aged landfill cover, from approximately 8-20 mg/hr from LFG flares (LFG included Hg(O) at microg/m3 concentrations), and from approximately 200-400 mg/hr at the WF. These fluxes exceed our earlier published estimates. Attempts to identify specific Hg sources in excavated and sorted waste indicated few readily identifiable sources; because of effective mixing and diffusion of Hg(O), the entire waste mass acts as a source. We estimate that atmospheric Hg releases from municipal landfill operations in the state of Florida are on the order of 10-50 kg/yr, substantially larger than our original estimates, but still a small fraction of current overall anthropogenic losses.     

Airborne Emissions of Mercury from Municipal Solid Waste. II: Potential Losses of Airborne Mercury before Landfill

Abstract

Waste distribution and compaction at the working face of municipal waste landfills releases mercury vapor (Hg⁰) to the atmosphere, as does the flaring of landfill gas. Waste storage and processing before its addition to the landfill also has the potential to release Hg⁰ to the air if it is initially present or formed by chemical reduction of Hg^II to Hg⁰ within collected waste. We measured the release of Hg vapor to the atmosphere during dumpster and transfer station activities and waste storage before landfilling at a municipal landfill operation in central Florida. We also quantified the potential contribution of specific Hg-bearing wastes, including mercury (Hg) thermometers and fluorescent bulbs, and searched for primary Hg sources in sorted wastes at three different landfills. Surprisingly large fluxes were estimated for Hg losses at transfer facilities (～100 mg/hr) and from dumpsters in the field (～30 mg/hr for 1,000 dumpsters), suggesting that Hg emissions occurring before landfilling may constitute a significant fraction of the total emission from the disposal/landfill cycle and a need for more measurements on these sources. Reducing conditions of landfill burial were obviously not needed to generate strong Hg⁰ signals, indicating that much of the Hg was already present in a metallic (Hg⁰) form. Attempts to identify specific Hg sources in excavated and sorted waste indicated few readily identifiable sources; because of effective mixing and diffusion of Hg⁰, the entire waste mass acts as a source. Broken fluorescent bulbs and thermometers in dumpsters emitted Hg⁰ at 10 to >100 μg/hr and continued to act as near constant sources for several days.     

Methylated mercury species in municipal waste landfill gas sampled in Florida,USA

Mercury-bearing material has been placed in municipal landfills from a wide array of sources including fluorescent lights, batteries, electrical switches, thermometers, and general waste. Despite its known volatility, persistence, and toxicity in the environment, the fate of mercury in landfills has not been widely studied. The nature of landfills designed to reduce waste through generation of methane by anaerobic bacteria suggests the possibility that these systems might also serve as bioreactors for the production of methylated mercury compounds. The toxicity of such species mandates the need to determine if they are emitted in municipal landfill gas (LFG). In a previous study, we had measured levels of total gaseous mercury (TGM) in LFG in the μg/m³ range in two Florida landfills, and elevated levels of monomethyl mercury (MMM) were identified in LFG condensate, suggesting the possible existence of gaseous organic Hg compounds in LFG. In the current study, we measured TGM, Hg⁰, and methylated mercury compounds directly in LFG from another Florida landfill. Again, TGM was in the μg/m³ range, MMM was found in condensate, and this time we positively identified dimethyl mercury (DMM) in the LGF in the ng/m³ range. These results identify landfills as a possible anthropogenic source of DMM emissions to air, and may help explain the reports of MMM in continental rainfall.     

Airborne emissions of mercury from municipal solid waste. II: potential losses of airborne mercury before landfill

Waste distribution and compaction at the working face of municipal waste landfills releases mercury vapor (Hg(o)) to the atmosphere, as does the flaring of landfill gas. Waste storage and processing before its addition to the landfill also has the potential to release Hg(o) to the air if it is initially present or formed by chemical reduction of Hg(II) to Hg(o) within collected waste. We measured the release of Hg vapor to the atmosphere during dumpster and transfer station activities and waste storage before landfilling at a municipal landfill operation in central Florida. We also quantified the potential contribution of specific Hg-bearing wastes, including mercury (Hg) thermometers and fluorescent bulbs, and searched for primary Hg sources in sorted wastes at three different landfills. Surprisingly large fluxes were estimated for Hg losses at transfer facilities (approximately 100 mg/hr) and from dumpsters in the field (approximately 30 mg/hr for 1000 dumpsters), suggesting that Hg emissions occurring before landfilling may constitute a significant fraction of the total emission from the disposal/landfill cycle and a need for more measurements on these sources. Reducing conditions of landfill burial were obviously not needed to generate strong Hg(o) signals, indicating that much of the Hg was already present in a metallic (Hg(o)) form. Attempts to identify specific Hg sources in excavated and sorted waste indicated few readily identifiable sources; because of effective mixing and diffusion of Hg(o), the entire waste mass acts as a source. Broken fluorescent bulbs and thermometers in dumpsters emitted Hg(o) at 10 to >100 microg/hr and continued to act as near constant sources for several days.     

Mercury emissions as landfill gas from a large-scale abandoned landfill site in Seoul

The composition of landfill gas (LFG) was analyzed for vapor-phase mercury (Hg) (primarily in its elemental form, Hg⁰) and relevant environmental parameters from 42 out of 106 ventpipes placed across two different sectors of the Nan-Ji-Do (NJD) landfill site in Seoul, Korea during September/October 2000. Results of our studies showed that large quantities of Hg emanated through these ventpipes which were infiltrated deep into the waste layer. The mean concentration of Hg, computed using the data sets collected from 42 ventpipes, was 420 ng m⁻³ with a range of 3.45–2952 ng m⁻³. Because large differences were apparent in its concentration levels not only between the two sectors of 1 and 2 but also between the plain and slope areas, evaluation of the data was made by dividing them into four different categories, namely plain areas of sectors 1 and 2 and slope areas of sectors 1 and 2. By categorizing the data in such a manner, the emission fluxes of ventilated Hg were estimated for each data group at the NJD site. The flux values of Hg for each data group were distinguished so that the enhanced fluxes were observed in plain compared to slope areas. The computed LFG fluxes of Hg from the whole NJD site were on the order of 23 g on an annual basis. The overall results of our study suggest that the vent emission of Hg from the study site is comparable in magnitude to those reported previously (e.g., the Florida landfill sites in US), while the LFG emissions of Hg may not necessarily be the most dominant source in the NJD site.     

Effect of biogas generation on radon emissions from landfills receiving radium-bearing waste from shale gas development

Dramatic increases in the development of oil and natural gas from shale formations will result in large quantities of drill cuttings, flowback water, and produced water. These organic-rich shale gas formations often contain elevated concentrations of naturally occurring radioactive materials (NORM), such as uranium, thorium, and radium. Production of oil and gas from these formations will also lead to the development of technologically enhanced NORM (TENORM) in production equipment. Disposal of these potentially radium-bearing materials in municipal solid waste (MSW) landfills could release radon to the atmosphere. Risk analyses of disposal of radium-bearing TENORM in MSW landfills sponsored by the Department of Energy did not consider the effect of landfill gas (LFG) generation or LFG control systems on radon emissions. Simulation of radon emissions from landfills with LFG generation indicates that LFG generation can significantly increase radon emissions relative to emissions without LFG generation, where the radon emissions are largely controlled by vapor-phase diffusion. Although the operation of LFG control systems at landfills with radon source materials can result in point-source atmospheric radon plumes, the LFG control systems tend to reduce overall radon emissions by reducing advective gas flow through the landfill surface, and increasing the radon residence time in the subsurface, thus allowing more time for radon to decay. In some of the disposal scenarios considered, the radon flux from the landfill and off-site atmospheric activities exceed levels that would be allowed for radon emissions from uranium mill tailings.

Implications: Increased development of hydrocarbons from organic-rich shale formations has raised public concern that wastes from these activities containing naturally occurring radioactive materials, particularly radium, may be disposed in municipal solid waste landfills and endanger public health by releasing radon to the atmosphere. This paper analyses the processes by which radon may be emitted from a landfill to the atmosphere. The analyses indicate that landfill gas generation can significantly increase radon emissions, but that the actual level of radon emissions depend on the place of the waste, construction of the landfill cover, and nature of the landfill gas control system.     

Electricity generation from landfill gas in Turkey

Landfill gas (LFG)-to-energy plants in Turkey were investigated, and the LFG-to-energy plant of a metropolitan municipal landfill was monitored for 3 years. Installed capacities and actual gas engine working hours were determined. An equation was developed to estimate the power capacity for LFG-to-energy plants for a given amount of landfilled waste. Monitoring the actual gas generation rates enabled determination of LFG generation factors for Turkish municipal waste. A significant relationship (R = 0.524, p < 0.01, two-tailed) was found between the amounts of landfilled waste and the ambient temperature, which can be attributed to food consumption and kitchen waste generation behaviors influenced by the ambient temperature. However, no significant correlation was found between the ambient temperature and the generated LFG. A temperature buffering capacity was inferred to exist within the landfill, which enables the anaerobic reactions to continue functioning even during cold seasons. The average LFG and energy generation rates were 45 m³ LFG/ton waste landfilled and 0.08 MWhr/ton waste landfilled, respectively. The mean specific LFG consumption for electricity generation was 529 ± 28 m³/MWhr.

Implications: The paper will be useful for local authorities who need to manage municipal waste by using landfills. The paper will also be useful for investors who want to evaluate the energy production potential of municipal wastes and the factors affecting the energy generation process mostly for economical purposes. Landfills can be regarded as energy sources and their potentials need to be investigated. The paper will also be useful for policymakers dealing with energy issues. The paper contains information on real practical data such as engine working hours, equation to estimate the necessary power for a given amount of landfilled waste, and son on.     

A survey of municipal solid waste landfills in Beijing during 2009–2011

The investigation of municipal solid waste (MSW) treatment in China is rare due to its sensitivity and difficulty in terms of access. We chose Beijing, the capital of China, as an example to identify the characteristics of MSW landfill treatments using a 2-month investigation with 20 participants. MSW landfill treatments account for nearly 70% of the annual MSW disposal in Beijing; the landfill processes are equipped with many kinds of technologies and consume a large amount of energy and produce a variety of contaminants. The cover method (the most obvious difference in landfill tamping) mainly includes high-density polyethylene (HDPE) geomembranes with loess and soil alone (i.e., loess or sandy soil). We investigated the actual conditions of landfills and collected data on leachate and landfill gas (LFG) emissions and energy consumption during 2009–2011. The results indicated that the cover method employed by landfills was related to treatment quantity, operation, and especially landfill location. Early large-scale landfills located in plains were covered with HDPE geomembranes, and newly built landfills covered with soil tended to be equipped with HDPE covers. Using HDPE cover also contributed greatly to LFG production due to its impermeability but had no remarkable effect on leachate yield reduction due to the dry climate in Beijing. The potential was reinforced by the potentials of decrement and reuse. The disposal method of LFG can be optimized, and the power generated by the LFG process can meet the landfill demand. The gray water recycled from the leachate could be used in the landfill process.

     

Surface emission of landfill gas from solid waste landfill

The surface emission of landfill gas (LFG) was studied to estimate the amount of LFG efflux from solid waste landfills using an air flux chamber. LFG efflux increased as atmospheric temperature increased during the day, and the same pattern for the surface emission was observed for the change of seasons. LFG efflux rate decreased from summer through winter. The average LFG efflux rates of winter, spring and summer were 0.1584, 0.3013 and 0.8597 m³ m⁻² h⁻¹ respectively. The total amount of surface emission was calculated based on the seasonal LFG efflux rate and the landfill surface area. From the estimates of LFG generation, it is expected that about 30% of the generated LFG may be released through the surface without extraction process. As forced extraction with a blower proceeded, the extraction well pressure decreased from 1100 to –100 mm H₂O, and the LFG surface efflux decreased markedly above 80%. Thus, the utilization of LFG by forced extraction would be the good solution for global warming and air pollution by LFG.     

Permeability test and slope stability analysis of municipal solid waste in Jiangcungou Landfill,Shaanxi, China

With the rapid increase of city waste, landfills have become a major method to deals with municipal solid waste. Thus, the safety of landfills has become a valuable research topic. In this paper, Jiangcungou Landfill, located in Shaanxi, China, was investigated and its slope stability was analyzed. Laboratory tests were used to obtain permeability coefficients of municipal solid waste. Based on the results, the distribution of leachate and stability in the landfill was computed and analyzed. These results showed: the range of permeability coefficient was from 1.0 × 10^–7 cm sec^–1 to 6.0 × 10^–3 cm sec^–1 on basis of laboratory test and some parameters of similar landfills. Owing to the existence of intermediate cover layers in the landfill, the perched water level appeared in the landfill with heavy rain. Moreover, the waste was filled with leachate in the top layer, and the range of leachate level was from 2 m to 5 m in depth under the waste surface in other layers. The closer it gets to the surface of landfill, the higher the perched water level of leachate. It is indicated that the minimum safety factors were 1.516 and 0.958 for winter and summer, respectively. Additionally, the slope failure may occur in summer.

Implications: The research of seepage and stability in landfills may provide a less costly way to reduce accidents. Landslides often occur in the Jiangcungou Landfill because of the high leachate level. Some measures should be implemented to reduce the leachate level. This paper investigated seepage and slope stability of landfills by numerical methods. These results may provide the basis for increasing stability of landfills.     

Trends in anthropogenic mercury emissions estimated for South Africa during 2000–2006

Recent studies suggest an increase in mercury (Hg) emissions to the global environment, particularly as a result of anthropogenic activities. This has prompted many countries to complete Hg emission inventories, based on country-specific Hg sources. In this study, information on annual coal consumption and Hg-containing commodities produced in South Africa, was used to estimate Hg emissions during 2000–2006. Based on the information, the UNEP toolkit was used to estimate the amount of Hg released to air and general waste from each activity; using South Africa specific and toolkit based emission factors. In both atmospheric and solid waste releases, coal-fired power plants were estimated to be the largest contributors of Hg emissions, viz. 27.1 to 38.9 tonnes y^?1 in air, and 5.8 to 7.4 tonnes y^?1 in waste. Cement production was estimated to be the second largest atmospheric Hg emission contributor (2.2–3.9 tonnes y^?1), while coal gasification was estimated to be the second largest Hg contributor in terms of general waste releases (2.9–4.2 tonnes y^?1). Overall, there was an increase in total atmospheric Hg emissions from all activities, estimated at ca. 34 tonnes in 2000, to 50 tonnes in 2006, with some fluctuations between the years. Similarly, the total Hg emissions released to general waste was estimated to be 9 tonnes in 2000, with an increase to 12 tonnes in 2006.     

Feasibility of Landfill Gas as a Liquefied Natural Gas Fuel Source for Refuse Trucks

Abstract

The purpose of this paper is to develop a methodology to evaluate the feasibility of using landfill gas (LFG) as a liquefied natural gas (LNG) fuel source for heavy-duty refuse trucks operating on landfills. Using LFG as a vehicle fuel can make the landfills more self-sustaining, reduce their dependence on fossil fuels, and reduce emissions and greenhouse gases. Acrion Technologies Inc. in association with Mack Trucks Inc. developed a technology to generate LNG from LFG using the CO₂ WASH process. A successful application of this process was performed at the Eco Complex in Burlington County, PA. During this application two LNG refuse trucks were operated for 600 hr each using LNG produced from gases from the landfill. The methodology developed in this paper can evaluate the feasibility of three LFG options: doing nothing, electricity generation, and producing LNG to fuel refuse trucks. The methodology involved the modeling of several components: LFG generation, energy recovery processes, fleet operations, economic feasibility, and decision-making. The economic feasibility considers factors such as capital, maintenance, operational, and fuel costs, emissions and tax benefits, and the sale of products such as surplus LNG and food-grade carbon dioxide (CO₂).

Texas was used as a case study. The 96 landfills in Texas were prioritized and 17 landfills were identified that showed potential for converting LFG to LNG for use as a refuse truck fuel. The methodology was applied to a pilot landfill in El Paso, TX. The analysis showed that converting LFG to LNG to fuel refuse trucks proved to be the most feasible option and that the methodology can be applied for any landfill that considers this option.     

Mercury speciation and mobility in mine wastes from mercury mines in China

Mercury (Hg) speciation and mobility were determined in calcines and waste rocks collected from 9 Hg mines in China. Total Hg (THg) concentrations in the mine wastes varied widely in different Hg mines (with a range of 0.369 to 2,620 mg kg^?1). Cinnabar is the dominant form of Hg in the mine wastes. However, Hg²⁺ and Hg⁰ concentrations in the calcines were significantly higher than these in the waste rocks, which suggested the retorting can produce large amounts of by-product Hg compounds. The THg and Hg⁰ concentrations in certain mine wastes exceeded soil guidelines recommended by US Environmental Protection Agency; while total soluble Hg concentrations of leachates in certain mine wastes exceeded National Surface Water Quality Standard of China. Mine wastes are important Hg pollution sources to the aquatic ecosystem and atmosphere.     

Validation of the integrated RAMS-Hg modelling system using wet deposition observations for eastern North America

Using the well-known Regional Atmospheric Modelling System (RAMS) version 4.3 an integrated system able to simulate the atmospheric mercury cycle has been developed. Basic processes of the mercury atmospheric cycle have been incorporated into the atmospheric model. The model deals with elemental Hg (Hg⁰), divalent gaseous Hg (Hg²) and particulate Hg (Hg^P). Wet deposition mechanisms used to describe the removal of Hg² and Hg^P are merged with the detailed cloud microphysical scheme in order to provide better representation of the wet deposition processes. The advantages of this approach have been examined through results intercomparison with simulated Hg wet deposition using CMAQ-Hg from previous work for two evaluation periods: 4 April–2 May 1995, and 20 June–18 July 1995. An attempt to clarify the main parameters that affect wet deposition mechanism of mercury is also made.     

Polymers as Solid Waste in Municipal Landfills

Abstract

Synthetic polymers reach municipal landfills as components of products such as waste household paints, packaging films, storage containers, carpet fibers, and absorbent sanitary products. Some polymers in consumer products that reach landfills are designed to photodegrade or biodegrade. This article examines the significance of degradable polymers in management of solid waste in municipal landfills. Most landfills are not designed to photodegrade or biodegrade solid waste. Landfill disposal of stable polymers such as polyacrylics and polyethylenes is not associated with significant polymer degradation or mobility. Stability to photodegradation and biodegradation is an advantage when municipal landfills are used for disposal of polymer products as solid waste. Use of landfill disposal can be a responsible means to manage polymer waste and can be part of an overall waste management plan which includes source reduction, recycling, reuse, composting, and waste-to-energy incineration.     

Modeling landfill gas potential and potential energy recovery from Thohoyandou landfill site,South Africa

ABSTRACT

The increase in solid waste generation has been a major contributor to the amount of Greenhouse gases (GHGs) present in the atmosphere. To some extent, a great chunk of these GHGs in the atmosphere is from landfill. This study assesses two theoretical models (LandGEM and Afvalzorg models) to estimate the amount of landfill gas (LFG) emitted from Thohoyandou landfill site. Also, the LFGcost Web model was used to estimate the cost and benefits of the implementation of an LFG utilization technology. The Thohoyandou landfill started operations in the year 2005 and it is proposed to reach its peak at approximately in the year 2026. The LandGEM calculates the mass of landfill gas emission using methane generation capacity, mass of deposited waste, methane generation constant and methane generation rate. Meanwhile, the Afvalzorg model determines the LFG emissions using the Methane correction factor, yearly waste mass disposal, waste composition, Degradation Organic Carbon, methane generation rate constant, LFG recovery efficiency. The study findings indicate that the methane (CH₄) and carbon dioxide (CO₂) emitted from the landfill estimated from LandGEM will peak in the year 2026 with values of 3517 Mg/year and 9649 Mg/year, respectively. Results from the Afvalzorg model show that CH₄ emission will peak in the year 2026 (3336 Mg/year). The LandGEM model showed that the total LFG, CH₄ and CO₂ emitted from the landfill between 2005 and 2040 are 293239.3 Mg/year, 78325.7 Mg/year and 214908.6 Mg/year, respectively. The simulation from the Afvalzorg model found that the CH₄ emitted from the years 2005– 2040 is 74302 Mg/year. The implementation of an LFG utilization technology was economically feasible from consideration of the sales of electricity generated and Certified Emission Reductions (CER) (carbon credits).     

The influence of ozone on atmospheric emissions of gaseous elemental mercury and reactive gaseous mercury from substrates

Experiments were performed to investigate the effect of ozone (O₃) on mercury (Hg) emission from a variety of Hg-bearing substrates. Substrates with Hg(II) as the dominant Hg phase exhibited a 1.7 to 51-fold increase in elemental Hg (Hg^o) flux and a 1.3 to 8.6-fold increase in reactive gaseous mercury (RGM) flux in the presence of O₃-enriched clean (50 ppb O₃; 8 substrates) and ambient air (up to ∼70 ppb O₃; 6 substrates), relative to clean air (oxidant and Hg free air). In contrast, Hg^o fluxes from two artificially Hg^o-amended substrates decreased by more than 75% during exposure to O₃-enriched clean air relative to clean air. Reactive gaseous mercury emissions from Hg^o-amended substrates increased immediately after exposure to O₃ but then decreased rapidly. These experimental results demonstrate that O₃ is very important in controlling Hg emissions from substrates. The chemical mechanisms that produced these trends are not known but potentially involve heterogenous reactions between O₃, the substrate, and Hg. Our experiments suggest they are not homogenous gas-phase reactions. Comparison of the influence of O₃ versus light on increasing Hg^o emissions from dry Hg(II)-bearing substrates demonstrated that they have a similar amount of influence although O₃ appeared to be slightly more dominant. Experiments using water-saturated substrates showed that the presence of high-substrate moisture content minimizes reactions between atmospheric O₃ and substrate-bound Hg. Using conservative calculations developed in this paper, we conclude that because O₃ concentrations have roughly doubled in the last 100 years, this could have increased Hg^o emissions from terrestrial substrates by 65–72%.     

Sewage Sludge to Landfill: Some Pertinent Engineering Properties

Abstract

More stringent controls on the quality of wastewater discharges have given rise to increasing volumes of sewage sludge for disposal, principally to land, using either land-spreading or sludge-to-landfill operations. Current sludge-to-landfill methods generally involve mixing the concentrated sludge with other solid waste in municipal landfills. However, stricter waste disposal legislation and higher landfill taxes are forcing the water industry to look for more efficient disposal strategies. Landfill operators are also increasingly reluctant to accept sludge material in the slurry state because of construction difficulties and the potential for instability of the landfill slopes. The engineering and drying properties of a municipal sewage sludge are presented and applied, in particular, to the design, construction, and performance of sewage sludge monofills. Sludge handling and landfill construction are most effectively conducted within the water content range of 85% water content, the optimum water content for standard proctor compaction, and 95% water content, the sticky limit of the sludge material. Standard proctor compaction of the sludge within this water content range also achieves the maximum dry density of ～0.56 tonne/m³, which maximizes the storage capacity and, hence, the operational life of the landfill site. Undrained shear strength-water content data (pertinent to the stability of the landfill body during construction) and effective stress-strength parameters, which take into account the landfill age and the effects of ongoing sludge digestion, are presented. Landfill subsidence, which occurs principally because of creep and decomposition of the solid organic particles, is significant and continues indefinitely but at progressively slower rates.     

Atmospheric mercury species in the European Arctic: Measurements and modelling

Concentrations of different species of mercury in arctic air and precipitation have been measured at Ny-Ålesund (Svalbard) and Pallas (Finland) during 1996–1997. Typical concentrations for vapour phase mercury measured at the two stations were in the range of 0.7–2 ng m⁻³ whereas particulate mercury concentrations were below 5 pg m⁻³. Total mercury in precipitation was in the range 3–30 ng l⁻¹. In order to evaluate the transport and deposition of mercury to the arctic from European anthropogenic sources, the Eulerian transport model HMET has been modified and extended to also include mercury species. A scheme for chemical conversion of elemental mercury to other species of mercury and deposition characteristics of different mercury species have been included in the model. European emission inventories for three different forms of Hg (Hg⁰, HgCl₂ and Hg_p) have been implemented in the numerical grid system for the HMET model.     

Anthropogenic mercury emissions in China

An inventory of mercury emissions from anthropogenic activities in China is compiled for the year 1999 from official statistical data. We estimate that China's emissions were 536 (±236) t of total mercury. This value includes open biomass burning, but does not include natural sources or re-emission of previously deposited mercury. Approximately 45% of the Hg comes from non-ferrous metals smelting, 38% from coal combustion, and 17% from miscellaneous activities, of which battery and fluorescent lamp production and cement production are the largest. Emissions are heaviest in Liaoning and Guangdong Provinces, where extensive smelting occurs, and in Guizhou Province, where there is much small-scale combustion of high-Hg coal without emission control devices. Emissions are gridded at 30×30 min spatial resolution. We estimate that 56% of the Hg in China is released as Hg⁰, 32% as Hg²⁺, and 12% as Hg^p. Particulate mercury emissions are high in China due to heavy burning of coal in residential and small industrial settings without PM controls. Emissions of Hg²⁺ from coal-fired power plants are high due to the absence of flue-gas desulfurization units, which tend to dissolve the soluble divalent mercury. Metals smelting operations favor the production of elemental mercury. Much of the Hg is released from small-scale activities in rather remote areas, and therefore the activity levels are quite uncertain. Also, emissions test data for Chinese sources are lacking, causing uncertainties in Hg emission factors and removal efficiencies. Overall, we calculate an uncertainty level of ±44% (95% confidence interval) in the estimate of total emissions. We recommend field testing of coal combustors and smelters in China to improve the accuracy of these estimates.