Wintertime PM2.5 and PM10 Source Apportionment at Sacramento,California

ABSTRACT

The chemical mass balance (CMB) model was applied to winter (November through January) 1991–1996 PM2.5 and PM10 data from the Sacramento 13th and T Streets site in order to identify the contributions from major source categories to peak 24-hr ambient PM_2.5 and PM₁₀ levels. The average monthly PM₁₀ monitoring data for the nine-year period in Sacramento County indicate that elevated concentrations are typical in the winter months. Concentrations on days of highest PM₁₀ are dominated by the PM2.5 fraction. One factor contributing to increased PM_2.5 concentrations in the winter is meteorology (cool temperatures, low wind speeds, low inversion layers, and more humid conditions) that favors the formation of secondary nitrate and sulfate aerosols. Residential wood burning also elevates fine particulate concentrations in the Sacramento area.

The results of the CMB analysis highlight three key points. First, the source apportionment results indicate that primary motor vehicle exhaust and wood smoke are significant sources of both PM_2.5 and PM₁₀ in winter. Second, nitrates, secondarily formed as a result of motor-vehicle and other sources of nitrogen oxide (NO_x), are another principal cause of the high PM_2.5 and PM₁₀ levels during the winter months. Third, fugitive dust, whether it is resuspended soil and dust or agricultural tillage, is not the major contributor to peak winter PM_2.5 and PM10 levels in the Sacramento area.     

Elemental characterization of PM10, PM2.5 and PM1 in the town of Genoa (Italy)

The particulate matter (PM) concentration and composition, the PM10, PM2.5, PM1 fractions, were studied in the urban area of Genoa, a coastal town in the northwest of Italy. Two instruments, the continuous monitor TEOM and the sequential sampler PARTISOL, were operated almost continuously on the same site from July 2001 to September 2004. Samples collected by PARTISOL were weighted to obtain PM concentration and then analysed by PIXE (particle induced X-ray emission) and by ED-XRF (energy dispersion X-ray fluorescence), obtaining concentrations for elements from Na to Pb. Some of the filters used in the TEOM microbalance were analysed by ED-XRF to calculate Pb concentration values averaged over 7-30 d periods.     

Chemical Composition and Source Apportionment of PM25 Particles in the Sihwa Area,Korea

ABSTRACT

To investigate the chemical characteristics of fine particles in the Sihwa area, Korea, atmospheric aerosol samples were collected using a dichotomous PM₁₀ sampler and two URG PM_2.5 cyclone samplers during five intensive sampling periods between February 1998 and February 1999. The Inductively Coupled Plasma (ICP)-Atomic Emission Spectrometry (AES)/ICP-Mass Spectrometry (MS), ion chromatograph (IC), and thermal manganese dioxide oxidation (TMO) methods were used to analyze the trace elements, ionic species, and carbonaceous species, respectively. Backward trajectory analysis, factor analysis, and a chemical mass balance (CMB) model were used to estimate quantitatively source contributions to PM_{2 5} particles collected in the Sihwa area.

The results of PM_2.5 source apportionment using the CMB7 receptor model showed that (NH₄)₂SO₄ was, on average, the major contributor to PM_2.5 particles, followed by nontraffic organic carbon (OC) emission, NH₄NO₃, agricultural waste burning, motor vehicle emission, road dust, waste incineration, marine aerosol, and others. Here, the nontraffic OC sources include primary anthropogenic OC emitted from the industrial complex zone, secondary OC, and organic species from distant sources. The source impact of waste incineration emission became significant when the dominant wind directions were from southwest and west sectors during the sampling periods. It was found that PM_2.5 particles in the Sihwa area were influenced mainly by both anthropogenic local sources and long-range transport and transformation of air pollutants.     

Source Apportionment of PM10 and PM25 in Five Chilean Cities Using Factor Analysis

ABSTRACT

Chile is a fast-growing country with important industrial activities near urban areas. In this study, the mass and elemental concentrations of PM₁₀ and PM_2.5 were measured in five major Chilean urban areas. Samples of particles with diameter less than 10 um (PM₁₀) and 2.5 um (PM_2.5) were collected in 1998 in Iquique (northern Chile), Valparaiso, Vina del Mar, Rancagua (central Chile), and Temuco (southern Chile). Both PM₁₀ and PM₂₅ annual mean concentrations (PM₁₀: 56.9-77.6 u,g/m³; PM₂₅: 22.4-42.6 u.g/m³) were significantly higher than the corresponding European Union (EU) and U.S. Environmental Protection Agency (EPA) air quality standards. Moreover, the 24-hr PM₁₀ and PM₂₅ U.S. standards were exceeded infrequently for some of the cities (Rancagua and Valparaiso).     

One-year study of the elemental composition and source apportionment of PM10 aerosols in Florence, Italy

An extensive investigation was carried out for the characterisation of the air particulate composition in Florence. The aim was to determine the aerosol elemental concentrations, as well as to identify pollution sources. For our investigation, the external Particle-Induced X-Ray Emission-Particle-Induced gamma-Ray Emission beam facility of the Istituto Nazionale di Fisica Nucleare, Van de Graaff accelerator at the Physics Department of the Florence University was used. We report the results of the analysis of a long temporal series (approximately 1 yr) of PM10 particulate samples, collected on Millipore filters on a daily basis in three different sites (characterised by different urban settings). Daily concentrations of more than 20 elements were detected. The long sampling period (approximately 1 yr) allowed a comparison with the air quality recommended values and the identification of seasonal variations. Four main sources (traffic, oil-combustion, soil-dust, and wind transported sea-salt) were extracted with the help of Principal Component Analysis (PCA). An absolute PCA showed traffic to be the major source both in the high traffic site and in the urban background site.     

Source Apportionment of Particulate Matter (PM10) and Indoor Dust in a University Building

A study on source apportionment of indoor dust and particulate matter (PM₁₀) composition was conducted in a university building by using chemometrics. The objective of this study was to investigate the potential sources of selected heavy metals and ionic species in PM₁₀ and indoor dust. PM₁₀ samples were collected using a low-volume sampler (LVS) and indoor dust was collected using a soft brush. Inductively coupled plasma spectrometry (ICP-MS) was used to determine the concentration of heavy metals, while the concentration of cations and anions was determined by atomic absorption spectrometer (AAS) and ion chromatography (IC), respectively. The concentration of PM₁₀ recorded in the building throughout the sampling period ranged from 20 ± 10 μgm^?3 to 80 ± 33 μgm^?3. The composition of heavy metals in PM₁₀ and indoor dust were dominated by zinc (Zn), followed by lead (Pb), copper (Cu), and cadmium (Cd). Principle component analysis (PCA) and multiple linear regression (MLR) showed that the main sources of pollutants in PM₁₀ came from indoor renovations (73.83%), vehicle emissions (16.38%), earth crust sources (9.68%), and other outdoor sources (0.11%). For indoor dust, the pollutant source was mainly earth crust. This study suggests that chemometrics can be used for forensic investigation to determine the possible sources of indoor contaminants within a public building.     

PM10: Results of a One-Year Monitoring Survey in the Netherlands

A comprehensive field assessment has been made of the measurement performance of PM10 inlets. Both precision and comparability are approximately 4 percent, complying well with the requirements of the proposed Federal Reference Method (FRM). Fluctuations in sampling efficiency play a dominant role. Hence, both comparability and precision can be interpreted in terms of changes in the 50 percent cutoff diameter D50. In this way a D50 performance of about 0.7 μm is deduced, clearly within the proposed FRM requirement of D50 = 10 ± 1 μm. There exists no fixed linear relationship between PM10 and TSP (total suspended particulate matter): different average situations yield different regression coefficients (Western Europe: 0.7 and USA: 0.5). Furthermore, there are different conversion factors, representative of average (0.5-0.7) or episodic situations of high concentration levels (0.8-0.9). Hence, TSP air quality standards should not be replaced by PM10 ones simply by using the regression results from various national studies because this could yield unequal stringent PM10 standards.     

Elemental composition of PM10 and PM2.5 in urban environment in South Brazil

The purpose of the present study is to analyze the elemental composition and the concentrations of PM₁₀ and PM_2.5 in the Guaíba Hydrographic Basin with HV PM₁₀ and dichotomous samplers. Three sampling sites were selected: 8° Distrito, CEASA and Charqueadas. The sampling was conducted from October 2001 to December 2002. The mass concentrations of the samplers were evaluated, while the elemental concentrations of Si, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu and Zn were determined using the Particle-Induced X-ray Emission (PIXE) technique. Factor Analysis and Canonical Correlation Analysis were applied to the chemical and meteorological variables in order to identify the sources of particulate matter. Industrial activities such as steel plants, coal-fired power plants, hospital waste burning, vehicular emissions and soil were identified as the sources of the particulate matter. Concentration levels higher than the daily and the annual average air quality standards (150 and 50 μg m⁻³, respectively) set by the Brazilian legislation were not observed.     

Source Apportionment of Phoenix PM2.5 Aerosol with the Unmix Receptor Model

Abstract

The multivariate receptor model Unmix has been used to analyze a 3-yr PM_2.5 ambient aerosol data set collected in Phoenix, AZ, beginning in 1995. The analysis generated source profiles and overall average percentage source contribution estimates (SCEs) for five source categories: gasoline engines (33 ± 4%), diesel engines (16 ± 2%), secondary SO₄ ^2? (19 ± 2%), crustal/soil (22 ± 2%), and vegetative burning (10 ± 2%). The Unmix analysis was supplemented with scanning electron microscopy (SEM) of a limited number of filter samples for information on possible additional low-strength sources. Except for the diesel engine source category, the Unmix SCEs were generally consistent with an earlier multivariate receptor analysis of essentially the same data using the Positive Matrix Factorization (PMF) model. This article provides the first demonstration for an urban area of the capability of the Unmix receptor model.     

Receptor Modeling for Elemental Source Contributions to Fine Aerosols in New York State

ABSTRACT

Fine atmospheric particulate material was collected at five sites in upstate New York and analyzed for its trace element composition by instrumental neutron activation analysis. Of the 3700 daily samples collected over a 2-yr period, 1459 were analyzed for 39 elements, providing a large and detailed data set. Factor analysis (FA) was used to identify potential pollution sources or source regions and to construct inorganic source profiles for each. Following FA, the method of absolute factor scores-multiple linear regression was used to estimate the absolute elemental contribution of each of the identified sources. Factor analysis identified nine sources impacting the sampling region. Seven of these were found to be present in varying degrees among of the sampling sites. The other two sources had more localized impacts and were observed at only one of the sites each. Regional sources (such as the midwestern United States and eastern Canada) and crustal/ soil material accounted for the greatest amount of the trace elements measured in the collected material.     

Particle Size Distributions and Elemental Composition of Atmospheric Particulate Matter in Southern Italy

Abstract

Three 2-wk seasonal field campaigns were performed in 2003 and 2004 at a sampling site on the southern Tyrrhenian coast of Italy with the aim to investigate the dynamics and characteristics of particle-bound pollutants in the Mediterranean area. Fine (PM_2.5) and coarse particulate matter (PM_10–2.5) size fractions were collected by a manual dichotomous sampler on 37-mm Teflon filters over a 24-hr sampling period. On average, 70% of the total PM₁₀ (PM_2.5 + PM_10–2.5) mass was associated with the coarse fraction and 30% with the fine fraction during the three campaigns. The ambient concentrations of Pb, Ni, Cr, Zn, Mn, V, Cd, Fe, Cu, Ca, and Mg associated with both size fractions were determined by atomic absorption spec-trometry. Ambient concentrations showed differences in their absolute value, ranging from few ng · m^-3 to µg ?m^-3, as well as in their variability within the PM_2.5 and PM_10–2.5 size fractions. PM₁₀ levels were well below the European Union (EU) limit value during the study period with the exception of three events during the first campaign (fall) and five events during the third campaign (spring). Two main sources were identified as the major contributors including mineral dust, transported from North Africa, and sea spray from the Tyrrhenian Sea. Comparing the results with backward trajectories, calculated using the Hybrid Single-Particle Lagrangian Integrated Trajectory Model (HYSPLIT) and Total Ozone Mapping Spectrometer-National Aeronautics and Space Administration (TOMS-NASA) maps, it was observed that in central and eastern Europe, the Tyrrhenian Sea and North Africa were the major emission source regions that affected the temporal variations and daily averages of PM_2.5 and PM_10–2.5 concentrations.     

Mass levels,crustal component and trace elements in PM10 in Palermo,Italy

Results concerning the levels and elemental compositions of daily PM₁₀ samples collected at four air quality monitoring sites in Palermo (Italy) are presented. The highest mean value of PM₁₀ concentrations (46 μg m⁻³, with a peak value of 158 μg m⁻³) was recorded at the Di Blasi urban station, and the lowest at Boccadifalco station (25 μg m⁻³), considered as a sub-urban background station. Seventeen elements (Al, As, Ba, Co, Cr, Cu, Fe, Li, Mn, Mo, Ni, Pb, Sb, Sr, U, V, Zn) were measured by ICP-MS. Al and Fe showed the highest concentrations, indicating the significant contribution of soil and resuspended mineral particles to atmospheric PM₁₀. Ba, Cr, Cu, Mn, Mo, Ni, Pb, Sb, V and Zn had higher concentrations at the three urban sampling sites than at the sub-urban background station. Besides soil-derived particles, an R-mode cluster analysis revealed a group of elements, Mo, Cu, Cr, Sb and Zn, probably related to non-exhaust vehicle emission, and another group, consisting of Ba, As and Ni, which seemed to be associated both with exhaust emissions from road traffic, and other combustion processes such as incinerators or domestic heating plants. The results also suggest that Sb, or the association Sb–Cu–Mo, offers a way of tracing road traffic emissions.     

Source apportionment of PM10 and PM2.5 in five Chilean cities using factor analysis

Chile is a fast-growing country with important industrial activities near urban areas. In this study, the mass and elemental concentrations of PM10 and PM2.5 were measured in five major Chilean urban areas. Samples of particles with diameter less than 10 microm (PM10) and 2.5 microm (PM2.5) were collected in 1998 in Iquique (northern Chile), Valparaiso, Vi?a del Mar, Rancagua (central Chile), and Temuco (southern Chile). Both PM10 and PM2.5 annual mean concentrations (PM10: 56.9-77.6 microg/m3; PM2.5: 22.4-42.6 microg/m3) were significantly higher than the corresponding European Union (EU) and U.S. Environmental Protection Agency (EPA) air quality standards. Moreover, the 24-hr PM10 and PM2.5 U.S. standards were exceeded infrequently for some of the cities (Rancagua and Valparaiso). Elements ranging from Mg to Pb were detected in the aerosol samples using X-ray fluorescence (XRF). For each of the five cities, factor analysis (FA) was applied to identify and quantify the sources of PM10 and PM2.5. The agreement between calculated and measured mass and elemental concentrations was excellent in most of the cities. Both natural and anthropogenic sources were resolved for all five cities. Soil and sea were the most important contributors to coarse particles (PM10-PM2.5), whereas their contributions to PM2.5 were negligible. Emissions from Cu smelters and oil refineries (and/or diesel combustion) were identified as important sources of PM2.5, particularly in the industrial cities of Rancagua, Valparaiso, and Vi?a del Mar. Finally, motor vehicles and wood burning were significant sources of both PM2.5 and PM10 in most of the cities (wood burning was not identified in Iquique).     

Characterisation of PM10 and PM2.5 particulate matter in the ambient air of Milan (Italy)

24-h simultaneous samplings of PM10 and PM2.5 particulate matter (PM) have been carried out during the period December 1997–September 1998 in the central urban area of Milan. The mass concentrations of the two fractions showed significant daily variations linked to different thermodynamic conditions of the planetary boundary layer (PBL) and characterised by higher values during wintertime. The elemental composition, determined by energy dispersive X-ray fluorescence technique, was quite different in the two fractions: in the finer one the presence of elements with crustal origin is reduced while the anthropogenic elements, with a relevant environmental and health impact, appear to be enriched. The composition data allowed a quantification of two major components of the atmospheric particulate: sulphates (mainly of secondary origin) and particles with crustal origin. An important but unmeasured component is likely constituted by organic and elemental carbon compounds.The multivariate analysis of elements, gaseous pollutants and mass concentration data-sets leads to the identification of four main sources contributing to PM10 and PM2.5 composition: vehicles exhaust emissions, resuspended crustal dust, secondary sulphates and industrial emissions. The existence of a possible background component with non-local origin is also suggested.     

Elemental Composition of Airborne Particulates And Source Identification: Data Analysis Techniques

Approaches are discussed and illustrated for the analysis of the very large trace element data set obtained by instrumental neutron activation and emission spectroscopic analysis of over 700, 24 hour ambient air particulate samples collected at 16 sites in Cleveland, OH from August 1971 to October 1972. Examples are presented of the use of pairwise correlation statistics, cluster analysis algorithms, enrichment factors, and pollutant concentration roses to identify sources. It is demonstrated that some elemental constituents of the Cleveland suspended particulate can be related to specific source types: earth’s crust (Al, Si, Sc, Ti, V, La, Sn, Eu, Oy, Th), automotive exhaust (Pb, Br), metallurgy (Fe, Cr, Co) and specific industries (Sb, Hg). Even with 24 hr samples, some sources can be geographically located by the directional characteristics of the element.     

Source apportionment of PM10 in six cities of northern China

Ambient PM₁₀ was sampled in six northern China cities (Urumqi, Yinchuan, Taiyuan, Anyang, Tianjin and Jinan) from December 1999 to July 2002, and analyzed for 16 chemical elements, two water-soluble ions, total carbon, and organic carbon. In addition, chemical source profiles consisting of the same particulate components were obtained from a number of naturally occurring geological sources (soil dust from exposed lands) and sources of atmospheric particulates resulting from human activities (resuspended dust, cement, coal combustion fly ash, vehicle exhaust, and secondary particles). Ambient and source data were used in a chemical mass balance (CMB) receptor model to determine the major source of PM₁₀ in these six cities. Results of CMB modeling showed that the major source of ambient PM₁₀ in all the cities was resuspended dust. Significant contributions from coal fly ash were also found in all six cities.     

Source apportionment of PM2.5 and PM10 aerosols in Brisbane (Australia) by receptor modelling

Aerosol samples for PM_2.5 and PM₁₀ (particulate matter with aerodynamic diameters less than 2.5 and 10 μm, respectively) were collected from 1993 to 1995 at five sites in Brisbane, a subtropical coastal city in Australia. This paper investigates the contributions of emission sources to PM_2.5 and PM₁₀ aerosol mass in Brisbane. Source apportionment results derived from the chemical mass balance (CMB), target transformation factor analysis (TTFA) and multiple linear regression (MLR) methods agree well with each other. The contributions from emission sources exhibit large variations in particle size with temporal and spatial differences. On average, the major contributors of PM₁₀ aerosol mass in Brisbane include: soil/road side dusts (25% by mass), motor vehicle exhausts (13%, not including the secondary products), sea salt (12%), Ca-rich and Ti-rich compounds (11%, from cement works and mineral processing industries), biomass burning (7%), and elemental carbon and secondary products contribute to around 15% of the aerosol mass on average. The major sources of PM_2.5 aerosols at the Griffith University (GU) site (a suburban site surrounded by forest area) are: elemental carbon (24% by mass), secondary organics (21%), biomass burning (15%) and secondary sulphate (14%). Most of the secondary products are related to motor vehicle exhausts, so, although motor vehicle exhausts contribute directly to only 6% of the PM_2.5 aerosol mass, their total contribution (including their secondary products) could be substantial. This pattern of source contribution is similar to the results for Rozelle (Sydney) among the major Australian studies, and is less in contributions from industrial and motor vehicular exhausts than the other cities. An attempt was made to estimate the contribution of rural dust and road side dust. The results show that road side dusts could contribute more than half of the crustal matter. More than 80% of the contribution of vehicle exhausts arises from diesel-fuelled trucks/buses. Biomass burning, large contributions of crustal matter, and/or local contributing sources under calm weather conditions, are often the cause of the high PM₁₀ episodes at the GU site in Brisbane.     

Estimating the impact of Saharan dust on the year 2001 PM10 record of Rome,Italy

This paper evaluates the role of Saharan dust advection in the exceeding of the PM₁₀ thresholds in the city of Rome, Italy. To this purpose, a series of observations and model forecasts recorded in the year 2001 are analysed and discussed. Lidar profiles collected over 168 days of the year are employed to both assess the presence and magnitude of Saharan dust layers over the city and to evaluate the depth of the planetary boundary layer. Backtrajectories are used to verify the Saharan origin of the lidar-sounded air masses. Model predictions of the presence of Saharan dust over the area are employed to fill the time gaps between lidar observations. PM₁₀ and carbon monoxide records of both a city background (Villa Ada) and a heavy traffic station (Magna Grecia) are cross-analysed with the dust events record and meteorological data. The analysis shows that: (1) Saharan dust was advected over Rome on about 30% of the days of 2001; (2) mean contribution of Saharan dust transport events to daily PM₁₀ levels was of the order of 20 μg m⁻³; (3) at the urban background station of Villa Ada, the Saharan contribution caused the surpassing of the maximum number of days in excess of 50 μg m⁻³ fixed by the current legislation (35 per year). Conversely, at the heavy traffic station of Magna Grecia the Saharan contribution was not determinant at causing the observed large exceeding of that limit, as well as of the maximum yearly average of 40 μg m⁻³; (4) 25% of the Saharan advection days (of the order of 100/year at Rome) led to a PM₁₀ increase >30 μg m⁻³, 4% caused an increase >50 μg m⁻³, thus leading on their own to surpassing the 50 μg m⁻³ daily limit.     

Spatial Differences in Outdoor PM10 Mass and Aerosol Composition in Mexico City

Abstract

Twenty-five MiniVol samplers were operated throughout the Mexico City metropolitan region from February 22 through March 22, 1997, to evaluate the variability of PM₁₀ concentrations and composition. The highest PM₁₀ concentrations were found in neighborhoods with unpaved or dirty roads, and elements related to crustal material were the main cause of differences from nearby (<200 m) monitors that were not adjacent to the roadbed. SO₄ ^2?concentrations were homogeneous across the city. SO₄ ^2?measured at the city boundaries was about two-thirds of the concentrations measured within the urbanized area, indicating that most SO₄ ^2? is of regional origin. Elemental carbon (EC) and organic carbon (OC) concentrations were highly variable, with higher concentrations in areas that had high diesel traffic and older vehicles. Spatial correlations among PM₁₀ concentrations were high, even though absolute concentrations were variable, indicating a common effect of meteorology on the concentration or dispersion of local emissions.     

Source apportionment of visual impairment during the California regional PM10/PM2.5 air quality study

Gases and particulate matter predictions from the UCD/CIT air quality model were used in a visibility model to predict source contributions to visual impairment in the San Joaquin Valley (SJV), the southern portion of California's Central Valley, during December 2000 and January 2001. Within the SJV, daytime (0800–1700 PST) light extinction was dominated by scattering associated with airborne particles. Measured daytime particle scattering coefficients were compared to predicted values at approximately 40 locations across the SJV after correction for the increased temperature and decreased relative humidity produced by “smart heaters” placed upstream of nephelometers. Mean fractional bias and mean fractional error were ?0.22 and 0.65, respectively, indicating reasonable agreement between model predictions and measurements. Particulate water, nitrate, organic matter, and ammonium were the major particulate species contributing to light scattering in the SJV. Daytime light extinction in the SJV averaged between December 25, 2000 and January 7, 2001 was mainly associated with animal ammonia sources (28%), diesel engines (18%), catalyst gasoline engines (9%), other anthropogenic sources (9%), and wood smoke (7%) with initial and boundary conditions accounting for 13%. The source apportionment results from this study apply to wintertime conditions when airborne particulate matter concentrations are typically at their annual maximum. Further study would be required to quantify source contributions to light extinction in other seasons.