A Comparison of Tailpipe,Dilution Tunnel,and Wind Tunnel Data in Measuring Motor Vehicle PM

ABSTRACT

Comparison between particle size distributions recorded directly at the tailpipes of both diesel and gasoline vehicles and measurements made using a conventional dilution tunnel reveals two problems incurred when using the latter method for studying particle number emissions. One is the potential for particulate matter (PM) artifacts originating from hydrocarbon material stored in the transfer hose connecting the tailpipe to the dilution tunnel, and the other is the particle coagulation (as well as condensation and chemical changes) that occurs during the transport. Both are potentially generic to current PM emissions measurement practices. The artifacts typically occur as a nanoparticle mode (10–30 nm) that is 2–4 orders of magnitude larger than what is present in the vehicle exhaust and can easily be mistaken for a similar mode that can arise from the nucleation of hydrocarbon or SO₄ ^2-components in the exhaust under appropriate dilution rates. Wind tunnel measurements are in good agreement with those made directly from the tailpipe and substantiate the potential for artifacts. They reveal PM levels for the recent model port fuel injection (PFI) gasoline vehicles tested that are small compared with the ambient background particle level during steady-state driving. The PM emissions recorded for drive cycles such as the Federal Test Procedure (FTP) and US06 occur primarily during acceleration, as has been previously noted. Light-duty diesel vehicle emissions normally exhibit a single lognormal mode centered between 55 and 80 nm, although a nonartifact nanoparticle mode in some cases appears at a 70-mph cruise up a grade.     

机动车颗粒污染物排放因子研究进展

综述了国内外几种常用的机动车颗粒污染物排放因子的确定方法,介绍了各模型的使用概况及其优缺点,最后提出对机动车颗粒污染物排放因子应深入开展有关研究。     

Wind Tunnel Modelling of Roadways: Comparison with Mathematical Models

The assessment of air quality impacts from roadways is a major concern to urban planners. In order to assess future road and building configurations, a number of techniques have been developed, including mathematical models, which simulate traffic emissions and atmospheric dispersion through a series of mathematical relationships and physical models. The latter models simulate emissions and dispersion through scaling of these processes in a wind tunnel. Two roadway mathematical models, HIWAY-2 and CALINE-4, were applied to a proposed development in a large urban area. Physical modelling procedures developed by Rowan Williams Davies & Irwin Inc. (RWDI) in the form of line source simulators were also applied, and the resulting carbon monoxide concentrations were compared. The results indicated a factor of two agreement between the mathematical and physical models. The physical model, however, reacted to changes in building massing and configuration. The mathematical models did not, since no provision for such changes was included in the mathematical models. In general, the RWDI model resulted in higher concentrations than either HIWAY-2 or CALINE-4. Where there was underprediction, it was often due to shielding of the receptor by surrounding buildings. Comparison of these three models with the CALTRANS Tracer Dispersion Experiment showed good results although concentrations were consistently underpredicted.     

Economic Comparison of Emission Control Systems for Glass Manufacturing Furnaces with Heat Recovery

ABSTRACT

Glass manufacturing, like other process industries, is faced with air pollution compliance problems due to ever stricter emission limits. Several waste gas cleaning equipment options are available for air pollution control (APC) in glass plants, the most common arrangements being based on electrostatic precipitator (ESP) or fabric filter (FF) dust collectors and semi-wet or dry processes for acid gas removal. However, several counteracting aspects affect the choice of gas cleaning technologies, which are confirmed by the discrepancies encountered in actual suppliers' bids. In this paper, the main pollution control options are analyzed by carrying out a critical comparison under the cost-effectiveness point of view to select the lowest cost arrangement considering capital investment, operating expenses, and energy-saving revenues from heat recovery processes. The analysis is carried out with reference to a case study involving actual float glass production lines at Pilkington plants in Italy.     

Remote Sensing Data and a Potential Model of Vehicle Exhaust Emissions

In June 1991, General Motors Research and Development Center (GMR&D) participated in a remote sensing study conducted by the California Air Resources Board and the U. S. Environmental Protection Agency. During this study, the GMR&D remote sensor was used to measure the carbon monoxide (CO) and hydrocarbon (HC) emissions from approximately 15,000 vehicles. The vehicle type (passenger car, light-duty truck, or medium/heavy-duty truck), manufacturer, and model year were identified for each vehicle by acquiring registration data from the state of California. Analyses were performed separately for each vehicle type and for passenger cars by separate model years. The data indicate that the passenger cars with the highest 10% of CO emissions generated approximately 58% of the total CO from all cars. Similarly, the 10% highest HC-emitting cars generated 65% of the total HC from cars. It was found that for each model year of vehicle, the distribution of emission concentrations followed a logarithmic relationship. The logarithmic functions that describe these relationships can be used to estimate the fraction of vehicles that emitted at or above any given concentration of CO or HC. However, these logarithmic functions only describe measured distributions for vehicles emitting more than 1% CO and 0.015% HC.     

Daily Variability of Motor Vehicle Emissions Derived from Traffic Counter Data

ABSTRACT

This work studied the daily variability of mobile sources in rural and urban areas, in and around the Atlanta Metropolitan Area. Traffic counter data collected during the 1992 Southern Oxidants Study Atlanta Intensive Study were used to analyze the spatial and temporal distribution of traffic volume. A simple method to study the daily variability of mobile emissions from the different types of urban and rural roads is presented. The method is based on hourly traffic volume data and emission factors and it has been generalized to describe the daily variability of mobile emissions for urban and rural areas and for the whole modeling domain. Implications of this study for improving mobile emission inventories are also discussed.     

Effects of Fuel Type,Driving Cycle,and Emission Status on In-Use Vehicle Exhaust Reactivity

ABSTRACT

The introduction of reformulated gasolines significantly reduced exhaust hydrocarbon (HC) mass emissions, but few data are available concerning how these new fuels affect exhaust reactivity. Similarly, while it is well established that high-emitting vehicles contribute a significant portion of total mobile source HC mass emissions, it is also important to evaluate the exhaust reactivity from these vehicles. The objective of this study was to evaluate the relative influence on in-use vehicle exhaust reactivity of three critical factors: fuel, driving cycle, and vehicle emission status. Nineteen in-use vehicles were tested with seven randomly assigned fuel types and two driving cycles: the Federal Test Procedure (FTP) and the Unified Cycle (UC). Total exhaust reactivity was not statistically different between the FTP and UC cycles but was significantly affected by fuel type. On average, the exhaust reactivity for California Phase 2 fuel was the lowest (16 % below the highest fuel type) among the seven fuels tested for cold start emissions. The average exhaust reactivity for high-emitting vehicles was significantly higher for hot stabilized (11%) and hot start (15%) emissions than for low-emitting vehicles. The exhaust reactivities for the FTP and UC cycles for light-end HCs and carbonyls were significantly different for the hot stabilized mode. There was a significant fuel effect on the mean specific reactivity (SR) for the mid-range HCs, but not for light-end HCs or carbonyls, while vehicle emission status affected the mean SR for all three HC compound classes.     

Intercomparison of Clean Air Status and Trends Network Nitrate and Nitric Acid Measurements with Data from Other Monitoring Programs

Abstract

The U.S. Environmental Protection Agency Clean Air Status and Trends Network (CASTNET) utilizes an open-face filter pack system to measure concentrations of atmospheric sulfur and nitrogen species. Concentration data for nitrogen species measured with filter pack systems sometimes deviate from data collected by other measurement systems used to measure the same species. The nature of these differences suggests that more than one sampling mechanism or atmospheric process is involved. The study presented here examines these differences by intercomparing CASTNET data with data from other studies, examining the results from earlier intercomparison studies, and conducting a field test to investigate the effect of particle size on filter pack measurement systems. Measurements of nitrogen species from the Maryland Aerosol Research and Characterization (MARCH) monitoring site were compared with nitrogen concentrations at three nearby CASTNET sites. Results indicate that CASTNET measured higher particulate nitrate (NO₃ ^-) and lower gaseous nitric acid (HNO₃) concentrations. Comparisons of NO₃ ^- from 34 collocated CASTNET and Inter-agency Monitoring of Protected Visual Environments (IMPROVE) sites show that CASTNET NO₃ ^- measurements were typically higher than the corresponding IM PROVE values. Also, results from the Lake Michigan Air Director’s Consortium Midwest Ammonia Monitoring Project demonstrated NO₃ ^- dissociation on Teflon filters. To investigate the effect of particle size, filter pack measurement systems were operated at three CASTNET sites with and without cyclones during six 7-day measurement periods from March to August 2006. Results indicate the size-selection cyclones had a significant effect on both NO₃ ^- and HNO₃ concentrations, but little effect on sulfate (SO₄ ^2-) and ammonium (NH₄ ⁺) levels. NO₃ ^- concentrations sampled with the open-face filters were significantly higher than concentrations measured with a 2.5-μm cut point, as were HNO₃ concentrations. Although limited in spatial and temporal coverage, the field study showed that the use of an open-face filter pack may allow for the collection of coarse NO₃ ^- particles and for the reaction of HNO₃ with metals/salts on the Teflon filter.     

Sensitivity Analysis and Evaluation of MicroFacCO: A Microscale Motor Vehicle Emission Factor Model for CO Emissions

ABSTRACT

This paper presents a sensitivity analysis of a microscale emission factor model (MicroFacCO) for predicting realtime site-specific motor vehicle CO emissions to input variables, as well as a limited field study evaluation of the model. The sensitivity analysis has shown that MicroFacCO emission estimates are very sensitive to vehicle fleet composition, speed, and ambient temperature. For the present U.S. traffic fleet, the CO emission rate (g/mi) is increased by more than 500% at 5 mph in comparison with a speed greater than 40 mph and by ~67% at ambient temperatures of 45 °F and ≥95 °F in comparison with an ambient temperature of 75 °F.     

The Impact of Particulate Emissions Control On the Control of Other MWC Air Emissions

On December 20, 1989, the Environmental Protection Agency (EPA) proposed revised new source performance standards for new municipal waste combustion (MWC) units and guidelines for existing sources. The proposed national regulations require tighter particulate matter control and address pre-combustion, combustion, and post-combustion controls, the latter two depending on capacity and age of the facility.

The air pollutants of concern when municipal solid waste (MSW) is burned will be discussed. Generally, particulate control is an inherent part of the systems used to limit the emissions of these air pollutants. The relationships between MWC air emissions (acid gases, trace organics, and trace heavy metals) control and particulate control will be discussed. Test results to quantify air pollutant emissions from MWC units and their control will be presented and compared with the proposed regulations.     

Estimations of Real-World N2O Emissions from Road Vehicles by Means of Measurements in a Traffic Tunnel

Abstract

Ambient air measurements of N₂O, NO_x, CO, and HC based on grab sampling were conducted in a major traffic tunnel in Sweden, that carries up to 4,000 vehicles per hour, in order to estimate real-world emissions of N₂O for road traffic. Two different methods—relative and mass balance—were used to calculate a N₂O emission factor for the mixed vehicle fleet, which gave an average emission factor, at average speeds of 30-70 km/h, of approximately 25 mg N₂O/ km, with a range of 7-56 mg/km.     

A Wind Tunnel Study of Gaseous Pollutants in City Street Canyons

Steady state mean concentrations of tracer gas were measured in a 400:1 scale model of an idealized city with variable geometry placed within a wind tunnel at various orientations to the mean flow for a free stream velocity of 6.8 ft/sec. The tracer gas was released from two parallel line sources to simulate lanes of traffic in an effort to quantify the persistence of pollution as well as the mean values realized at street levels. An aerodynamically rough turbulent boundary layer of neutral thermal stratification was employed to simulate the atmosphere. Values of concentration measured in the model city were converted to prototype concentrations in ppm and compared to National Ambient Air Quality Standards. It was shown that single isolated structures may cause favorable mixing of pollution downwind but very high concentrations exist in the immediate leeward vicinity of the building. Two favorable geometries for city blocks tested were found to reduce pedestrian exposure to pollution both near heavy traffic congestion and downwind. It was concluded that the pollutant dilution was controlled by the mean flow rather than by turbulent diffusion and that the lateral spread of the plume was slight as one proceeded downwind of the line source. The combination of favorable geometry and higher dilution velocities may bring pollution levels down to existing Air Quality Standards. The body of information presented in this paper should interest city planners and air quality monitoring personnel, as well as those researchers attempting to study and model flow in city street canyons. It provides order of magnitude estimates on pedestrian and office worker exposure to pollutants under a wide range of conditions.     

Nashville Sulfur Dioxide Emission Inventory and the Relationship of Emission to Measured Sulfur Dioxide

A detailed inventory of sulfur dioxide emissions was prepared as part of the Nashville Community Air Pollution Study conducted by the Public Health Service during 1958–59. The primary purpose of the inventory was to provide data for a study of the relationship between the emission of sulfur dioxide and measured ambient levels. The development of the inventory, data collection methods, and calculations are described. Ambient levels of sulfur dioxide were related to average emissions of sulfur dioxide in such a way (correlation coefficient = 0.81) that mean seasonal concentrations of atmospheric sulfur dioxide in square-mile areas could be predicted with fairly good confidence from a knowledge of sulfur dioxide emissions. For these long-period {average) predictions meteorological variables can be disregarded. On a square-mile basis, on the average, one ton of sulfur dioxide emitted per day produced a mean atmospheric sulfur dioxide concentration of 0.022 ppm, and 10 tons of sulfur dioxide per day produced a concentration of 0.067 ppm.     

Use of Subsampled Traffic Data to Estimate Roadway Emissions,Including Conversion to MOBILE6 Vehicle Classifications

Abstract

Air quality is degraded by many factors, among which the emissions from on‐road vehicles play a significant role. Timely and accurate estimate of such emissions becomes very important for policy‐making and effective control measures. However, lack of traffic data and outdated emission software make this task difficult. This research has demonstrated a new method that facilitates the vehicular emission inventories at the local level by using shorter-time Highway Performance Monitoring System (HPMS) traffic data along with the latest U.S. Environment Protection Agency (EPA) emission modeling software, MOBILE6. The conversion methodology was developed for converting readily available HPMS traffic volume data into EPA MOBILE-based traffic classifications, and a corresponding software program was written for automating the process. EPA MOBILE6 model was used to obtain emissions of nitrogen oxides (NO_x), volatile organic compound (VOC), and cabon monoxide (CO) emitted by the parent traffic and subsampled traffic data, and these emissions were additionally compared. The case study has shown that the difference of the magnitude between the emission estimates produced by certain subsampled and parent traffic data are minor, indicating that subsampled HPMS data can be used for reporting parent traffic emissions. It was also observed that traffic emissions follow a Weibull distribution, and NO_x emissions were more sensitive to the traffic data composition than VOC and CO. Lastly, use of average emission values of 20 or 30 consecutive minutes appears to be valid for representing hourly emissions.