Combustion and emission characteristics of a direct injection,compression‐ignition engine when operated on Honge oil,HOME and blends of HOME and diesel

This paper reports the results of research conducted to study the fuel properties of Honge oil and blends of its ester and the subsequent testing of these oils in a four‐stroke, single cylinder, water‐cooled, direct injection, compression‐ignition (CI) engine. Experiments were conducted with injection timings of 19, 23 and 27° BTDC at various loads and at a constant rated speed of 1500?rev?min^?1. The performance and emission characteristics of Honge oil and Honge oil methyl ester (HOME) blended with diesel, to produce blends designated B20, B40 and B80, were studied. The heat release rates, maximum rate of pressure rise, ignition delay, and combustion duration for these fuel combinations were determined.     

Effects of EGR on performance and emissions of a diesel engine fuelled with balanites aegyptiaca/diesel blends

In this study, balanites Aegyptiaca (L.) Del biodiesel was blended in proportions of 10% and 20% on the volume basis with diesel fuel and tested in a single cylinder, VCR diesel engine under measured load conditions with varied EGR rates (0, 10 and 20%). The results showed that B10 and B20 blends shown a significant reduction rate in terms of NO_x emissions that were familiar with biodiesel blends. At peak load conditions, BTE increased slightly for test fuel blends compared with pure diesel fuel while the BSFC rate and EGT suffered from increasing and decreasing nature with respect to blending percentage. From the emissions point of view, with the increase in blends percentage, a significant reduction rate is observed in terms of CO and HC concentrations (up to 12.34 and 17.5%, respectively) while NOx emissions decreased at peak load conditions (up to 24.34%). HC and CO emissions decreased with increase in blends percentage. However, lower levels of NO_x and EGT (up to 21.37 and 8.47%, respectively) and the average increase in terms of BTE and BSFC (up to 2.83 and 2.9%, respectively) can be realised with B20 test fuel blend under 20% EGR rate.     

Influence of olive mill wastewater in composting and impact of the compost on a Swiss chard crop and soil properties

The suitability of olive mill wastewater (OMW) for composting was studied by the addition of this liquid waste to a mixture of cotton gin waste and sewage sludge, and its composting was compared with that of another pile of similar composition, but without olive mill wastewater. Both piles were composted by the Rutgers static pile system in a pilot plant. To study the effects of both composts on plant yield and soil properties, a plot experiment was carried out with Swiss chard (Beta vulgaris L. var. cicla). Five treatments were applied: mineral fertiliser and two doses (30 and 60 tons ha(-1)) of both composts. The olive mill wastewater addition produced a compost with lower organic matter and nitrate concentrations, higher electrical conductivity, and a stabilised and humified organic matter similar to that of the compost produced without olive mill wastewater. The olive mill wastewater compost application to soil did not injure plants, producing a similar plant yield to both compost without olive mill wastewater and inorganic fertiliser. Also, the accumulation of potentially toxic heavy metals in plants cultivated with organic or mineral fertilisers did not reveal significant differences. The olive mill wastewater compost application to soil also improved the chemical and physicochemical properties of the soil.     

The influence of temperature and hydration on the sorption properties of bentonite

The effects of exposure to synthetic groundwater at elevated temperature gradients on the sorption properties of bentonite were investigated using the Mock-Up-Cz experiment. This experiment simulated the vertical placement of a container of radioactive waste according to the Swedish KBS-3 system for a period of more than 3 years. The mineralogical composition, as well as its chemical and physico-chemical properties, including the uptake of (99)TcO(4)(-) and (134)Cs(+), was used to evaluate the chemical changes caused by the long-term exposure of bentonite buffer to thermal and hydration gradients. It was found that the bentonite material was predominantly stable. No more than 2% of the montmorillonite was transformed due to thermal and moisture gradients. It was concluded that the new-formed mineral phases have no significant influence on the ion exchange and sorption properties of bulk bentonite samples.     

Robustness testing of a free-fall triboelectric separation process for plastic waste recovery

Among the separation techniques used in industries, the triboelectric separation of insulating particles using a rotary tube is an effective way employed in the waste recovery of plastic and mineral products. This process, also called free-fall triboelectric separation, is widely used for the sorting of granular mixtures resulting from industrial plastic wastes. Given that the robustness of such a separation process is an important issue, a standard procedure is used for determining the set point and for minimising the process sensitivity of sorting mixed particles of different polymers to changes in the values of some critical factors. The aim of this paper was to analyse the efficiency of the triboelectric separation process of polymers with respect to any slight variation in the values of the most significant factors. Experiments with a sample of high-density polyethylene and polyvinyl chloride plastic granules were carried out on a laboratory experimental bench. Several one-factor-at-a-time experiments, followed by two factorial designs (one composite and the other fractional), were performed based on the following experimental procedure: (1) determination of the variation limits of the input variables; (2) identification of the set point and (3) robustness testing of the process, i.e. testing whether the performance of the system remains high even when the factors vary slightly around the set point.     

Morphological peculiarities as indicators of natural history of sable (<Emphasis Type="Italic">Martes zibellina</Emphasis>) in North-Asia Pacific coast

Few studies exist on phenotypic composition of the sable populations in the Russian Far East, China and Japan. We present new data on the morphological diversification of sable for 20 mainland and island populations in an effort to document existing variability and produce baseline data that would be useful in constructing phylogenies for this species. Сlinal variability of skull size, cranial phene, foramen in fossa condyloidei inferior (FFCI), and fur coloration is revealed. One district, Central Sikhote-Alin, is characterized by sables with the minimum cranial size and the maximum phene expression. The area between the Uda River and Goryun and Amgun rivers is inhabited by sables of the darkest fur coloration. Moving out from those areas in all directions we were detected a trend of increasing skull size, reduction of cranial phene, and decreasing color intensity of fur. The skull size of sable is consistent with Bergmann’s rule. Special attention paid to the particular morphological properties of insular populations in specific climatic conditions and under isolation from the continent. They are characterized by minimal expression phene FFCI (Bolshoi Shantar, Iturup, and Hokkaido islands) and larger skull size, especially in sable of Kamchatka Peninsula. It is hypothesized that the area of the lower Amur Basin was a source of sable postglacial dispersal on the Eurasian Continent.     

Synthesis and speciation of polyaluminum chloride for water treatment

In this study, synthesis and speciation of polyaluminum chloride (PAC) for application in water treatment was investigated using a colorimetric speciation method. It was possible to produce stable preparations of PAC solutions in which a relatively stable cationic polymer predominated. The mode of preparation has a dramatic effect on the composition of PAC preparation. Some important parameters such as hydroxyl ligand number, mixing intensity, base injection rate and method, and aging were identified in this study.     

Biological vs. chemical properties of natural organic matter isolated from selected Norwegian lakes

Relationships among different spectroscopic, chemical, and biological properties of dissolved natural organic matter (NOM) were investigated. NOM samples were isolated by means of reverse osmosis from eight Norwegian lakes. Elemental composition, absorption spectra (UV, VIS, IR), the influence on algal growth, and accumulation rates of metals by mussels in the presence of NOM were measured. Linear regression and principal components analyses were utilised to assess relationships between the biological and chemical properties. It was concluded that the content of organic matter in the isolates and the aromaticity of NOM, as characterised by UV and VIS spectra, are best correlated with the biological properties.     

Performance and emission characteristic studies on CRDI diesel engine fuelled with plastic pyrolysis oil blended with ethanol and diesel

ABSTRACT

This paper mainly focuses on the utilisation of plastic pyrolysis oil (PPO) and its’ blends with diesel and ethanol in different proportions in a modified diesel engine fitted with common rail direct injection (CRDI) facility. PPO was subsequently blended with diesel and ethanol and characterisation has been done. Experiments were conducted to investigate the impact of injection timing (IT) and injection pressure (IP) on the performance of modified CRDI engine fuelled with PPO and its blends with diesel and ethanol. From the experimental investigations, IT of 10°bTDC and IP of 900 bar were found as best operating parameters to obtain maximum brake thermal efficiency (BTE) with lowered emissions for the fuel combinations utilised in the investigations. PPO as substitute to diesel fuel could be viable if its major concern is to finding permanent resources.     

Vertical distribution and characteristics of soil humic substances affecting radionuclide distribution

The humic substances extracted from different soil depths are separated into humic (HA) and fulvic (FA) acids, and characterized for their chemical composition, proton exchange capacity, spectroscopic characteristics and binding properties to the europium ion. The chemical and spectroscopic results show that FA compared to HA has a relatively high O/C ratio, high acidic functional group contents and low aromatic contents. The synchronous fluorescence spectroscopic results show that the stability constant (K) of the soil humic substances with Eu(III) ion tends to increase as the soil depth becomes deeper, and HA has a slightly stronger binding ability than FA. The measured total site concentrations (C(L)) reveal that Eu(III) ion is loaded onto HA by 62-77% of the total acid sites, but FA is only approximately 50% covered by Eu(III) ion. Information could be useful in understanding the migration of radionuclides in soil layer.     

Combustion performance and emission characteristics on HCCI engine of waste plastic pyrolysis oil biodiesel blends with external PFI and vaporiser

ABSTRACT

Analysis of plastic oil obtained from waste plastic through pyrolysis process, as an alternative to biodiesel is presented in this paper. The HCCI engine is considered for experimental validation of combustion performance and emission characteristics. To accumulate pyrolysis oil as fuel, the design modifications were made in external mixture formation on the existing computerised 4-stroke, single cylinder, water cooled, direct injection kirloskar diesel engine connected with eddy current dynamometer to satisfy HCCI conditions. HCCI engine can be worked on wide assortment of fuels beginning from diesel to different blends (WPPO 5%,10%,15% and 20% by volume) of biodiesel .The designed additional device connected to the engine is utilised for fuel vaporisation and mixture arrangement. In the experimental study, the combustion results were initiate to be of 39.69 % higher Rate of Heat Release (RoHR) for biodiesel HCCI as compared with diesel HCCI. Higher brake thermal efficiency (BTE) was found 37 % without exhaust gas recirculation (EGR) at WPPO 20 % biodiesel blend. And also found 50 % and 65 % reduction in NOx emission and 18 % and 28 % reduction in smoke opacity are obtained for biodiesel vapour induction without EGR and biodiesel vapour induction with 15 % EGR as compared with diesel fuel. The CO (0.34 %), and UHC (2.15 %) emissions are increases with 15 % EGR, but the emissions are within the standard limits specified by the emissions standards.     

Characteristics of soil organic matter (SOM) extracted using base with subsequent pH lowering and sequential pH extraction

Humic substances from eight soils of varying properties were extracted by two different methods: (1) the traditional NaOH-extraction with subsequent acidification to different pH (approximately 1 to approximately 12) and sequential extractions using 0.01 M NaNO(3) at incremental pH (approximately 1 to approximately 11). Cumulative organic matter (OM) in the sequential extractions showed properties that were consistent with NaOH-extracted OM. The release of Al and Fe in the sequential extractions was closely related with the release of organic carbon (OC). The ratio of OC associated with humic acid (HA) and fulvic acid (FA) (the HA:FA ratio) varied widely among the soils indicating heterogeneity in their OM composition. However, a significant correlation between this HA:FA ratio and the NaOH extractable %OC content of the soils is indicative of the possible relationship between them. Between pH 5 and 7, which is a typical soil solution pH, a significant amount of HA-associated OC was soluble. In modeling metal speciation in soil solutions, it has been assumed that all dissolved organic carbon (DOC) that is active toward metal binding is associated with FA. The results of this study indicate that the validity of these assumptions based on model sensitivity alone is questionable.     

Relationship between Habitat Properties and Composition of Communities in Conifer–Broadleaf Forest

Ecological and phytocenotic features of forest communities were studied in the southwest of Moscow oblast. Based on the ecomorphological groups of species prevalent in the herb–dwarf shrub and moss layers, five groups of communities typical of the conifer–broadleaf forest zone were distinguished (small-herb, small herb-large herb, large-herb, moist-herb, and mixed-herb communities), and their composition was analyzed. Discriminant analysis of the species composition of lower vegetation layers revealed significant differences between the syntaxa, with the percentage of correct classification being 89.8%. To evaluate ecological determination of the above groups of communities, a hypothesis was tested concerning the correlation of their composition with ecotope properties. This hypothesis was verified by means of (1) ordination by ecological indicator values and interpretation of the axes, (2) revealing differences in ecological regimes between habitats of the syntaxa, and (3) combined analysis of on-ground and remote sensing data, particularly spectral brightness of satellite images and morphometric characteristics of the terrain surface. The results confirmed the informativeness of the syntaxa distinguished based on the species composition of the ground vegetation layer and mapping of the ecological regimes of habitats.     

Influence of atmospheric stability on the mass concentration and chemical composition of atmospheric particles: a case study in Rome, Italy

PM(10) concentration and chemical composition (ions and carbon compounds) at three sampling stations in Rome and in its surroundings was determined daily during a one-month field study, carried out during December 2003. PM concentration at the traffic station was considerably higher than at the urban background and semi-rural stations; elemental carbon was detected as one of the chemical components responsible for this increase. The difference in the concentration of sulphate and ammonium was negligible, as it was expected for secondary pollutants. A negative artefact in the determination of ammonium nitrate by means of heated automatic monitors was highlighted. The dilution properties of the lower atmosphere were traced by means of a natural radioactivity monitor. This parameter has been found to play an essential role in pollution buildup. A considerable increase in PM concentration was observed to coincide with periods of atmospheric stability. The main difference in PM composition between periods of high concentration and periods of "clean" air was found to be in the increase of ammonium nitrate concentration.     

Toxicity of tire debris leachates

Data on the indicators of environmental impact of tire debris, originated from the tire abrasion on roads, are extremely scarce, while it is well known that tires may produce deleterious effects. Tire debris contains significant quantities of zinc (Zn) which may be released by tire rubber. We have used tire particles (TD) produced in laboratory from new rubber. Two sets of experiments were set up to obtain eluates. One set used 50 and 100 g/L TD to produce eluates at pH 3-7. The Zn quantity was measured with a Inductively Coupled Plasma-Atomic Emission Spectrometry. The eluates at 1%,10%,50%,100% concentrations in culture media were tested on Raphidocelis subcapitata, Daphnia magna and Xenopus laevis embryos (FETAX test). The other set of experiments was performed putting 250 mg/L TD in a column with glass beads to control particle dispersion during the elution process. We demonstrate that factors such as pH, size and particles aggregation deeply influence the elution process, that the amount of Zn leached from particles is related to their aggregation rather than their quantity. These results, even though do not reflect the real environmental toxicity of the leachates, can be successfully used for comparative purposes allowing an initial assessment of the potential effect of tire derived particles.     

Industrial applications of natural fibre-reinforced polymer composites – challenges and opportunities

The growing industrial demand for sustainable materials has led to a paradigm shift in the focus from synthetic polymers towards natural fibres. This paper deals with the challenges and opportunities associated with the use of natural fibre-reinforced polymer composites in various industrial applications. Natural fibres being biodegradable, light in weight, cost-effective and environment friendly are good candidate materials for modern industrial applications. Use of natural fibres in various industries with a focus on automotive and furniture industry has been discussed. The commonly used natural fibres in polymer composites including jute, hemp, sisal, kenaf, bamboo, cotton, flax, abaca, coir etc. have been dealt with in this paper. The literature revealed that tensile strength and other mechanical properties of these fibres are comparable to synthetic fibres like glass or carbon fibres. However, the temperature stability of polymers limits their extensive use and remains an issue to be addressed.     

Management of sludge from fish ponds at the edge of the Itaparica Reservoir (Brazil): an alternative to improve agricultural production

Sludge generated in intensively managed tilapia fingerling breeding ponds near the Itaparica Dam in the semi-arid Brazilian northeastern region was tested as a soil conditioner to produce lettuce in an effort to mitigate the present environmental impact of the deposition of this sludge, thereby giving it a productive destiny. A greenhouse experiment was performed by mixing the sludge with a Haplic Planosol topsoil, a characteristic soil of the region, so that the sludge corresponded to 0, 25, 50, 75, and 100% of the mixture (substrate). The experiment was set up as a randomized block design with five blocks, each with three pots (5-kg substrate per pot) of the five sludge proportion treatments. One lettuce plant was transplanted into each pot, maintained under greenhouse conditions, and harvested 35 days after transplanting. Sludge, soil, and the substrates were evaluated for nutrient concentration and physical characteristics. Green and dry weights, stem diameter, and nitrogen, phosphorus, and potassium concentrations in the aboveground parts of the lettuce plants were determined. Sludge incorporation into the substrate improved its chemical and physical characteristics. The lettuce plants grew best in the substrate with 75% sludge, increasing its biomass production by 50% and more than doubling its nitrogen uptake.     

Reuse of mining wastewater in agricultural activities in Jordan

A pilot study was completed in the Al-Abyad area near phosphate mining activity in Jordan. Six plots of 50 m² each were planted with two types of plant species (Zea mays spp. and Medicago lupulina spp.) and irrigated using three types of water (fresh groundwater, mine wastewater, and hydride water consisting of 50% fresh and 50% mine wastewater) to investigate the suitability of utilizing mine wastewater for food production in the area. Water, soil and plant sampling was completed for each plot over different time intervals and analyzed for heavy metal (Cr⁺⁶, Ni⁺², Zn⁺² and Pb⁺²) in addition to major ionic composition of the water used for irrigation. Crop yield was estimated at the end of the experiment. Plots irrigated with mine wastewater showed slightly higher heavy metals concentrations and soil salinity during the experiment period was higher for plots irrigated with mine wastewater compared to plots irrigated with fresh water, and it was uniform through the upper 45 cm of the soil profile due to the high amount of irrigation water used during the experiment. Crop yield was inversely proportional to salinity as an increase of salinity by 2-folds resulted in reducing yield by almost 50%. However, no risk of heavy metals contamination was found in plants and soil. Readers should send their comments on this paper to: BhaskarNath@aol.com within 3 months of publication of this issue.     

Combustion and emission characteristics of a direct injection CI engine when operated on Marotti oil methyl ester and blends of Marotti oil methyl ester and diesel

This paper presents a feasibility study of Marotti oil biodiesel as an alternative to diesel fuel for a compression ignition engine. Marotti oil is inedible and available mainly in the state of Kerala. The oil is extracted from Marotti seeds. However, the high viscosity, poor volatility and cold flow characteristics of many vegetable oils in general, and Marotti oil in particular, can cause problems such as injector coking, severe engine deposits, filter gumming, piston ring sticking and thickening of lubrication from long-term use in diesel engines. These problems can be eliminated or minimised by transesterification of the vegetable oils to form monoesters. Although transesterification improves the fuel properties of vegetable oil, the viscosity and volatility of biodiesel are still worse than for petroleum diesel fuel. Subsequently, Marotti oil was converted into its methyl ester by the process of transesterification. The methyl ester was blended with diesel in various proportions to obtain different blends of Marotti oil with diesel. The performance, emission and combustion characteristics of Marotti methyl ester and its blends with diesel were studied and the results were compared with the base line data generated for diesel operation. Experiments were conducted using an injection timing of 23° before top dead centre (BTDC) and an injection pressure of 205 bar at various power outputs and at a constant rated speed of 1500 rpm. The engine manufacturer specifies an injection timing of 23° BTDC and injection pressure of 205 bar for the standard diesel fuel operation. The heat release rates, maximum rate of pressure rise, ignition delay and combustion duration for these fuel combinations were obtained.

From the results obtained, it was observed that the biodiesel produced from Marotti oil and its blends with diesel have slightly reduced brake thermal efficiency and increased smoke, hydrocarbon, carbon monoxide and reduced NO _x emissions compared with diesel-only operation. The investigation showed that the B20 biodiesel blend of Marotti oil with diesel produced better performance in terms of higher brake thermal efficiency, lower specific fuel consumption and comparatively lower emissions compared to the other blend ratios considered.     

Experimental investigation of solar-powered desiccant cooling system by using composite desiccant “CaCl<Subscript>2</Subscript>/jute”

A solar-powered composite desiccant cooling system has been experimentally investigated. It consists of evacuated tube solar water heater, composite desiccant bed heat exchanger (CDBHE), direct evaporative cooling unit and cooling tower. The composite desiccant material has been synthesized by using iron mesh and jute layer impregnated with calcium chloride solution, and this composite desiccant is placed in shell- and tube-type heat exchanger to make CDBHE. In this desiccant cooling system, the evacuated tube solar water heater is used to produce required hot water for regeneration of composite desiccant material. A cooling tower is used to produce cooling water which is pumped into CDBHE during dehumidification process to remove heat of adsorption. Direct evaporative cooling unit is used to cool the outlet process air of CDBHE. It has been found that the average dehumidification rate increases by 54.1 % when using circulating cooling water. The COP_th of desiccant cooling system has been found to be 0.46 with a cooling capacity of 353.8 W.