Recycling of plastic packaging waste in Bandung City,Indonesia

Economic growth, changing consumption and production patterns are resulting in rapid increase in the generation of plastic wastes, including plastic packaging waste (PPW). A variety of PPW is identified in the municipal solid waste (MSW) stream. In this paper, quantity and composition of PPW at generators (residential and nonresidential sectors) and at the informal sector of waste recycling were measured, and accordingly the flow of PPW within Bandung City, Indonesia was analyzed. Though the generation rate per capita is not so high (25.1 g per day), total PPW generated by 2.3 million inhabitants in Bandung becomes 58.4 tonnes per day (3.76 % of total MSW generated). Due to lack of integrated MSW management, most of PPW is neither collected properly nor disposed of in appropriate manner by the municipality. Collection of valuable wastes including PPW is done predominantly by the informal sector without regard to health and safety. It is predicted that total PPW recycled by various informal waste recycling players like scavengers, junkmen, intermediates, and dealers is 27.5 tonnes per day (64.6 % of total PPW generated). Interviews regarding the existing handling methods and incentives preferred by generators to increase the recycling rate are also presented.     

生物滴滤法处理药厂高浓度丙酮废气的中试研究

采用生物滴滤工艺对某药厂硫代纯化车间的高浓度丙酮废气进行中试规模的处理运行。现场风量在3000~4000 m^3/h范围波动,丙酮质量浓度在0~2278 mg/m^3范围波动。在39 d的运行期间,丙酮的平均脱除效率为78%,最高可达100%;系统的平均单位去除负荷为139.2 g/(h·m^3),最高可达482.1 g/(h·m^3)。在高浓度高波动的进气工况条件下,单位生物矿化量可以保持相对稳定的水平,波动范围为11.5~27.3 g/(h·m^3),生物系统的稳定性和鲁棒性较好。循环液COD与进气负荷具有一定的相关性。     

IC反应器处理MTO废水的中试研究

中试研究了内循环(IC)反应器处理甲醇制烯烃(MTO)废水的启动和运行过程,同时考察了颗粒污泥的性状及沼气产量的变化情况。试验过程运行稳定,系统抗冲击性强。以絮状污泥为接种污泥,经过131 d的启动和运行,IC反应器的COD去除负荷可达10 kg/(m~3·d)以上,COD去除率可达90%以上。IC反应器中的成熟颗粒污泥形状规则、密实、粒径大、沉降速率快。IC反应器的沼气产量符合理论预期。     

废纸包装材料的研究现状及发展趋势

介绍了废纸包装材料的研究、应用和进展,分析了现有废纸材料应用上的优势及不足,提出了废纸包装材料的发展趋势。     

稠油采出水处理中试

以活性焦为吸附剂,采用预吸附—水解酸化—曝气生物固定床滤池—后吸附组合工艺中试处理稠油采出水。试验结果表明,当预吸附进水COD为408.6~526.7 mg/L、预吸附池活性焦泥回流量为25%(w)、水解酸化池上升流速为0.22 m/h、曝气生物固定床滤池气水体积比为10∶1、后吸附池投加新活性焦2 kg时,组合工艺对稠油采出水COD的去除率达到90.0%,出水COD均值为46.2 mg/L,出水水质满足DB 21/1627—2008《辽宁省污水综合排放标准》。     

An overview of methods for biodegradability testing of biopolymers and packaging materials

This paper gives an overview of the methods used at the Technical Research Centre of Finland (VTT) for the biodegradability testing of solid polymers and packaging materials. Biodegradability of each polymer included in the packaging material should be separately tested. Aquatic aerobic and anaerobic tests and, in specific cases, enzymatic tests are used for screening purposes. The application of aquatic aerobic tests—an automated Sturm test (OECD 301B; ASTM D5209) and a VTT headspace test as well as an anaerobic test (ASTM D5210)—is discussed. Three composting tests and their applications are summarized. These tests are regarded as important because they can be used to simulate the biodegradability under real-life conditions. Several tests are needed to determine the fate of the polymer under real conditions and to study its biodegradability in different environments. The time needed for complete biodegradation of polymers in nature is impossible to predict with laboratory tests and should be studiedin vivo.According to the lecture given in Sweden at the Royal Institute of Technology, at a workshop on polymers from renewable resources and their degradation, November 10–11, 1994.     

Hydrothermal carbonization of food waste and associated packaging materials for energy source generation

Hydrothermal carbonization (HTC) is a thermal conversion technique that converts food wastes and associated packaging materials to a valuable, energy-rich resource. Food waste collected from local restaurants was carbonized over time at different temperatures (225, 250 and 275 °C) and solids concentrations to determine how process conditions influence carbonization product properties and composition. Experiments were also conducted to determine the influence of packaging material on food waste carbonization. Results indicate the majority of initial carbon remains integrated within the solid-phase at the solids concentrations and reaction temperatures evaluated. Initial solids concentration influences carbon distribution because of increased compound solubilization, while changes in reaction temperature imparted little change on carbon distribution. The presence of packaging materials significantly influences the energy content of the recovered solids. As the proportion of packaging materials increase, the energy content of recovered solids decreases because of the low energetic retention associated with the packaging materials. HTC results in net positive energy balances at all conditions, except at a 5% (dry wt.) solids concentration. Carbonization of food waste and associated packaging materials also results in net positive balances, but energy needs for solids post-processing are significant. Advantages associated with carbonization are not fully realized when only evaluating process energetics. A more detailed life cycle assessment is needed for a more complete comparison of processes.     

Pyrolysis behavior of different type of materials contained in the rejects of packaging waste sorting plants

In this paper rejected streams coming from a waste packaging material recovery facility have been characterized and separated into families of products of similar nature in order to determine the influence of different types of ingredients in the products obtained in the pyrolysis process. The pyrolysis experiments have been carried out in a non-stirred batch 3.5 dm³ reactor, swept with 1 L min^?1 N₂, at 500 °C for 30 min. Pyrolysis liquids are composed of an organic phase and an aqueous phase. The aqueous phase is greater as higher is the cellulosic material content in the sample. The organic phase contains valuable chemicals as styrene, ethylbenzene and toluene, and has high heating value (HHV) (33–40 MJ kg^?1). Therefore they could be used as alternative fuels for heat and power generation and as a source of valuable chemicals. Pyrolysis gases are mainly composed of hydrocarbons but contain high amounts of CO and CO₂; their HHV is in the range of 18–46 MJ kg^?1. The amount of COCO₂ increases, and consequently HHV decreases as higher is the cellulosic content of the waste. Pyrolysis solids are mainly composed of inorganics and char formed in the process. The cellulosic materials lower the quality of the pyrolysis liquids and gases, and increase the production of char.     

A comparison of refuse attenuation in laboratory and field scale lysimeters

For this study, small and middle scale laboratory lysimeters, and a large scale field lysimeter in situ in Shanghai Refuse Landfill, with refuse weights of 187,600 and 10,800,000 kg, respectively, were created. These lysimeters are compared in terms of leachate quality (pH, concentrations of COD, BOD and NH3-N), refuse composition (biodegradable matter and volatile solid) and surface settlement for a monitoring period of 0-300 days. The objectives of this study were to explore both the similarities and disparities between laboratory and field scale lysimeters, and to compare degradation behaviors of refuse at the intensive reaction phase in the different scale lysimeters. Quantitative relationships of leachate quality and refuse composition with placement time show that degradation behaviors of refuse seem to depend heavily on the scales of the lysimeters and the parameters of concern, especially in the starting period of 0-6 months. However, some similarities exist between laboratory and field lysimeters after 4-6 months of placement because COD and BOD concentrations in leachate in the field lysimeter decrease regularly in a parallel pattern with those in the laboratory lysimeters. NH3-N, volatile solid (VS) and biodegradable matter (BDM) also gradually decrease in parallel in this intensive reaction phase for all scale lysimeters as refuse ages. Though the concrete data are different among the different scale lysimeters, it may be considered that laboratory lysimeters with sufficient scale are basically applicable for a rough simulation of a real landfill, especially for illustrating the degradation pattern and mechanism. Settlement of refuse surface is roughly proportional to the initial refuse height.     

Performance of compostable baby used diapers in the composting process with the organic fraction of municipal solid waste

In modern societies, disposable diapers constitute a significant percentage of municipal solid wastes. They have been traditionally landfilled or incinerated as only limited recycling processes are being implemented in some parts of Europe. With the implementation of separated collection systems for the organic fraction of municipal solid wastes (OFMSWs) and the need to preserve the environment, compostable diapers have appeared in the market to avoid the main environmental impacts associated to non-biodegradable disposable diapers. In this study, a full-scale composting of door-to-door collected OFMSW with a 3% (w/w) of compostable diapers has also been carried out. Previously, lab-scale experiments confirmed that almost 50% of carbon of compostable diapers is emitted as CO₂ under aerobic controlled conditions. The results obtained at full-scale demonstrate that both the composting process and the final end product (compost) are not altered by the presence of compostable diapers in crucial aspects such as pathogenic content, stability and elemental composition (including nutrients and heavy metals). The main conclusion of this study is that the collection of the OFMSW with compostable diapers can be a new way to transform this waste into high-quality compost.     

英国包装废物管理、产生和回收经验

英国制定了包装管理法规,提出了国家回收目标和公司回收目标。英国包装废物的总体回收率和再生利用率逐年提高,通过良好的环保理念、宣传措施、经济措施和建立回收体系,实现提高全社会参与包装废物回收和利用的水平。     

Perspectives for pilot scale study of RDF in Istanbul,Turkey

Municipal solid waste (MSW) is one of the most important environmental problems arising from rapid urbanization and industrialization. The use of alternative fuels in rotary kilns of cement plants is very important for reducing cost, saving fossil fuels and also eliminating waste materials, accumulated during production or after using these materials. Cement industries has an important potential for supplying preferable solutions to the waste management. Energy recovery from waste is also important for the reduction of CO₂ emissions.This paper presents an investigation of the development of refuse derived fuel (RDF) materials from non-recycling wastes and the determination of its potential use as an alternative fuel in cement production in Istanbul, Turkey. RDF produced from MSW was analyzed and its effects on cement production process were examined. For this purpose, the produced RDF was mixed with the main fuel (LPG) in ratios of 0%, 5%, 10%, 15% and 20%. Then chemical and mineralogical analyses of the produced clinker were carried out. It is believed that successful results of this study will be a good example for municipalities and cement industries in order to achieve both economic and environmental benefits.     

美国包装废物管理、回收体系及产生回收状况

包装废物既产生于工业生产过程,也产生于商业物质循环流过程,更产生于居民的日常生活,是一类广泛存在的废物和资源。通过大量的资料和数据全面分析了美国的包装废物管理、产生和回收体系的特点和发展趋势,其中的一些经验可以为我国包装废物的管理提供借鉴。     

Pilot installation for the thermo-chemical characterisation of solid wastes

The increasing production and the large variety of wastes require operators of thermal treatment units to continuously adapt the installations or the functioning parameters to the different physical and chemical properties of the wastes. Usually, the treated waste is encountered in the form of heterogeneous mixtures. The classical tests such as thermogravimetry and calorimetric bomb operate component by component, separately. In addition to this, they can analyse only small quantities of waste at a time (a few grams). These common tests are necessary but insufficient in the global waste analysis in the view further thermal treatment. This paper presents an experimental installation, which was designed and built at the CNRS Science Division, Department of Industrial Methods, Compiègne University of Technology, France. It allows the determination of waste thermal and chemical properties by means of thermal treatment. Also, it is capable of continuously analysing significant quantities of waste (up to 50kg/h) as compared to the classical tests and it can work under various conditions: The installation reproduces the process conditions from incinerators or pyrolysis reactors. It also provides complete information on the kinetics of the waste thermal degradation and on the pollutant emissions. Using different mixtures of components present in the municipal solid waste and also in the reconstituted MSW samples, we defined a series of criteria for characterising waste behaviour during the stages of the main treatment process such as: feeding, devolatilisation/oxidation, advancement, solid residue evacuation, and pollutants emission.     

Definition of compostability criteria for packaging: Initiatives in Italy

The management of solid waste is changing. The traditional approach based on landfilling of mixed refuses is shifting toward a system based on the at-source sorting of waste into specific fractions. The biological treatment of the organic fraction is considered to be an appropriate form of disposal not only for the “traditional≓ feedstock such as food scraps and vegetable and garden waste, but also for biodegradable packaging, when not recyclable in other ways. Any change from a complex system to another is difficult since many factors are to be organized and optimized. Industry must develop and manufacture compostable products, municipalities must build composting plants and organize source-separated collection, and regulatory bodies must define widely acceptable criteria of compostability. In Europe, the European Union has assigned the last task to the CEN, to provide common criteria and avoid hindrance to commercial exchanges. In Italy the UNI, the national standardization organization, has produced a working document to contribute to the discussion on the European level. In this paper the UNI scheme is described. A condensed version of this paper was presented by one of the authors (F.D.I.) at the 5th annual meeting of the BEDP Society, held in Nashville, September 22–26, 1996, during a session covering International Standards for Biodegradation Testing.     

Effect of exposure test conditions on leaching behavior of inorganic contaminants from recycled materials for roadbeds

Throughout the utilization of recycled materials, weathering factors such as humidity, gas composition and temperature have the potential to change the material properties and enhance the release of inorganic contaminants. In this research, the effects of weathering factors on recycled gravel materials for roadbeds were evaluated by applying three kinds of accelerating exposure tests: freezing–melting cycle test, carbonation test, and dry–humid cycle test. The effects of exposure tests were determined by X-ray diffraction (XRD) analysis and serial batch leaching test, making it possible to identify the change in release mechanisms. Sixteen elements, mainly metals, were investigated. Tested samples were molten slag from municipal solid waste, molten slag from automobile shredded residue, and crushed natural stone.After the exposure tests, the increase of cumulative release in the leaching test was generally less than 2.0 times that of the samples without the exposure test. Among the three test conditions, freezing–melting showed a slightly higher effect of enhancing the release of constituents. XRD analysis showed no change in chemical species. From these results, it was determined that the stony samples were stable enough so that their properties were not significantly changed by the exposure tests.