Indexing method for assessment of pollution potential of leachate from non-engineered landfill sites and its effect on ground water quality

Dumping of solid waste in a non-engineered landfill site often leads to contamination of ground water due to leachate percolation into ground water. The present paper assesses the pollution potential of leachate generated from three non-engineered landfill sites located in the Tricity region (one each in cities of Chandigarh, Mohali and Panchkula) of Northern India and its possible effects of contamination of groundwater. Analysis of physico-chemical properties of leachate from all the three landfill sites and the surrounding groundwater samples from five different downwind distances from each of the landfill sites were collected and tested to determine the leachate pollution index (LPI) and the water quality index (WQI). The Leachate Pollution Index values of 26.1, 27 and 27.8 respectively for landfill sites of Chandigarh (CHD), Mohali (MOH) and Panchkula (PKL) cities showed that the leachate generated are contaminated. The average pH values of the leachate samples over the sampling period (9.2 for CHD, 8.97 for MOH and 8.9 for PKL) show an alkaline nature indicating that all the three landfill sites could be classified as mature to old stage. The WQI calculated over the different downwind distances from the contamination sites showed that the quality of the groundwater improved with an increase in the downwind distance. Principal component analysis (PCA) carried out established major components mainly from natural and anthropogenic sources with cumulative variance of 88% for Chandigarh, 87.1% for Mohali and 87.8% for Panchkula. Hierarchical cluster analysis (HCA) identifies three distinct cluster types for the groundwater samples. These clusters corresponds to a relatively low pollution, moderate pollution and high pollution regions. It is suggested that all the three non-engineered landfill sites be converted to engineered landfill sites to prevent groundwater contamination and also new sites be considered for construction of these engineered landfill sites as the present dumpsites are nearing the end of their lifespan capacity.     

生活垃圾填埋场覆盖膜破损及其环境影响

中国的垃圾填埋场目前多采用高密度聚乙烯膜(HDPE)进行覆盖,已建成的填埋场均存在不同程度覆盖膜破损现象。采用填埋气泄漏可视化检测技术对中国东部某大型生活垃圾填埋场开展覆盖膜完整性检测,揭示了覆盖膜破损特征及破损成因,明确了破损点泄漏量,评估了其温室效应影响,梳理了国内外填埋场覆盖层监管相关管理规定和措施。结果表明:尖锐物体应力损伤导致的破损是填埋场覆盖膜破损的主要类型,粗放施工、监管机制不足、维护管理不到位是造成填埋场覆盖膜破损的主要原因。破损点的甲烷泄漏量约为817.2 m³/d,约合每年向大气环境释放温室气体超过4 900 t CO₂-eq。完善填埋场污染控制标准和技术规范、加强填埋场覆盖膜完整性的监管,是控制填埋场温室气体排放和推进固废处置设施碳减排的重要举措。     

A new method for environmental site assessment of urban solid waste landfills

Regarding various types of pollutant, waste management requires high attention. Environmental site selection study, prior to landfill operation, and subsequently, monitoring and maintaining of the location, are of foremost points in landfill site selection process. By means of these studies, it is possible to control the undesirable impacts caused by landfills. Study ahead aims at examination of effectiveness of a new method called Monavari 95–2 in landfill site assessment. For this purpose, two landfills Rasht and Andisheh, which are, respectively, located on humid and arid areas, were selected as case studies. Then, the results obtained from both sites were compared with each other to find out the weaknesses and strengths of each site. Compared with others similar methods, much more criteria (53 parameters) can be considered within this method, so the results will be more calculable. According to this method, Rasht landfill (site H) is classified as unacceptable landfill site i.e. there is an urgent need for a new suitable site for landfill, while Andishe Landfill (site D) is ranked as acceptable landfill site but needs environmental management program to handle the existing weaknesses.     

A Superiority-Inferiority-Based Inexact Fuzzy Stochastic Programming Approach for Solid Waste Management Under Uncertainty

A superiority–inferiority-based inexact fuzzy stochastic programming (SI-IFSP) model was developed for planning municipal solid waste management systems under uncertainty. The SI-IFSP approach represents a new attempt to tackle multiple uncertainties in objective function coefficients which are beyond the capabilities of existing inexact programming methods. Through introducing the concept of fuzzy random boundary interval, SI-IFSP is capable of reflecting multiple uncertainties (i.e., interval values, fuzzy sets, probability distributions, and their combinations) in both the objective function and constraints, leading to enhanced system robustness. The developed SI-IFSP method was applied to a case study of long-term municipal solid waste management. Useful solutions were generated. A number of decision alternatives could be generated based on projected applicable conditions, reflecting the compromise between system optimality and reliability as well as the tradeoffs between economic and environmental objectives. Moreover, the consequences of system violations could be quantified through introducing a set of economic penalties, reflecting the relationships between system costs and constraint violation risks. The results suggest that the proposed SI-IFSP method can explicitly address complexities in municipal solid waste management systems and is applicable to practical waste management problems.     

Toxicity Testing of Leachate from Waste Landfills Using Medaka (Oryzias Latipes) for Monitoring Environmental Safety

To investigate the environmental safety of waste disposal landfill sites and of land reclaimed from such sites, we evaluated the toxicity of leachate from these sites by a combination of bioassays in the Japanese killifish medaka Oryzias latipes. We tested for lethal toxicity in adult and larval medaka and for hatching inhibition of embryos from eggs. As biochemical evidence of the effects of leachate exposure, CYP1A (EROD activity) and vitellogenin (Vtg) were induced. We also bioassayed water-treated leachate and downstream river water. Leachate solution was lethal to larval and adult medaka. Embryo hatchability was inhibited, and abnormal hatching, spinal deformity and anisophthalmia occurred in embryos exposed to leachate solution. CYP1A was induced by exposure to leachate solution diluted to 1.0%, and EROD activity was significantly higher than in control. Vtg and unknown proteins were induced in the sera of male medaka exposed to the diluted leachate solution. Conventional water treatments worked effectively to remove toxic compounds but did not work well to remove element ions, including heavy metals. Treated leachate produced neither lethal toxicity nor hatching abnormalities during the exposure period. Fish toxicity tests for leachate would be useful for monitoring the environmental safety of landfill sites.     

Selection of MSW landfill site for Konya, Turkey using GIS and multi-criteria evaluation

Landfill is a common solution for the final disposal of municipal solid waste (MSW) in Turkey. Landfill siting is an extremely difficult task to accomplish because the site selection process depends on different factors and regulations. To ensure that an appropriate site is chosen, a systematic process should be developed and followed. Unsuccessful landfill siting is typically the result of strong public opposition. In this study, candidate sites for an appropriate landfill area in Cumra County of Konya City are determined by using the integration of geographic information systems (GIS) and multi-criteria evaluation (MCE). ArcGIS 9.0 software and its extensions were used as the GIS tool since it is able to perform suitability analysis using MCE analysis. To identify appropriate landfill areas in the Cumra district, eight input map layers including proximity to municipal and local wells and irrigational canals, distance from transportation routes and rails, distance from archaeological sites, distance from urban areas, land use/land cover, and land slope are used in constraint mapping. A final map was generated which identifies regions showing suitability for the location of the landfill site. According to the map, 6.8% of the study area is most suitable, 15.7% is suitable, 10.4% is moderately suitable, 25.8% is poorly suitable, and 41.3% is unsuitable. At the end of the analyses, three candidate sites are determined. The selection of the final MSW landfill site, however, requires further field research.     

Solid waste disposal site selection with GIS and AHP methodology: a case study in Senirkent�CUluborlu (Isparta) Basin, Turkey

The appropriate site selection for waste disposal is one of the major problems in waste management. Also, many environmental, economical, and political considerations must be adhered to. In this study, landfill site selection is performed using the Geographic Information System (GIS), the Analytical Hierarchy Process (AHP), and the remote sensing methods for the Senirkent?CUluborlu Basin. The basin is located in the E?irdir Lake catchment area, which is one of the most important fresh water in Turkey. So, waste management must be regulated in the basin. For this aim, ten different criteria (lithology, surface water, aquifer, groundwater depth, land use, lineaments, aspect, elevation, slope, and distance to roads) are examined in relation to landfill site selection. Each criterion was identified and weighted using AHP. Then, each criterion is mapped using the GIS technique, and a suitability map is prepared by overlay analyses. The results indicate that 96.3% of the area in the basin is unsuitable; 1.6%, moderately suitable; and 2.1%, most suitable. Finally, suitable regions in the basin are determined for solid waste landfill disposal and checked in the field. The selected and investigated regions are considered to be suitable for the landfill.     

Environmental monitoring of offshore drilling for petroleum exploration (MAPEM Project): shallow waters

This paper deals with the characteristics and composition of municipal solid waste (MSW) generated in Sangamner city. The composition of solid waste was studied by segregating it into different component, i.e., kitchen waste, paper, earth and fine material, slaughter house waste, leaves, metals, etc. These components were categorised into organic waste and inorganic waste. It was observed that Sangamner city produces around 61% organic waste, and the rest is inorganic waste. The characteristics of organic solid waste, i.e., pH, electrical conductivity, moisture content, organic carbon, nitrogen, phosphorus and potassium were evaluated. The analysis of organic content of MSW indicates that it is good source of nutrients for the agriculture sector whereas inorganic material can be used for landfill.     

Geospatial strategy for sustainable management of municipal solid waste for growing urban environment

This paper presents the implementation of a Geospatial approach for improving the Municipal Solid Waste (MSW) disposal suitability site assessment in growing urban environment. The increasing trend of population growth and the absolute amounts of waste disposed of worldwide have increased substantially reflecting changes in consumption patterns, consequently worldwide. MSW is now a bigger problem than ever. Despite an increase in alternative techniques for disposing of waste, land-filling remains the primary means. In this context, the pressures and requirements placed on decision makers dealing with land-filling by government and society have increased, as they now have to make decisions taking into considerations environmental safety and economic practicality. The waste disposed by the municipal corporation in the Bhagalpur City (India) is thought to be different from the landfill waste where clearly scientific criterion for locating suitable disposal sites does not seem to exist. The location of disposal sites of Bhagalpur City represents the unconsciousness about the environmental and public health hazards arising from disposing of waste in improper location. Concerning about urban environment and health aspects of people, a good method of waste management and appropriate technologies needed for urban area of Bhagalpur city to improve this trend using Multi Criteria Geographical Information System and Remote Sensing for selection of suitable disposal sites. The purpose of GIS was to perform process to part restricted to highly suitable land followed by using chosen criteria. GIS modeling with overlay operation has been used to find the suitability site for MSW.     

An evaluation of alternative household solid waste treatment practices using life cycle inventory assessment mode

Waste disposal is an important part of the life cycle of a product and is associated with environmental burdens like any other life-cycle stages. In this study, an integrated assessment for solid waste treatment practices, especially household solid waste, was undertaken to evaluate the impact contribution of household solid waste treatment alternatives towards the sustainable development by using Life Cycle Inventory Assessment method. A case study has been investigated under various possible scenarios, such as (1) landfill without landfill gas recovery, (2) landfill with landfill gas recovery and flaring, (3) landfill with landfill gas recovery and electric generation, (4) composting, and (5) incineration. The evaluation utilized the Life Cycle Inventory Assessment method for multiple assessments based on various aspects, such as greenhouse gas emission/reduction, energy generation/consumption, economic benefit, investment and operating cost, and land use burden. The results showed that incineration was the most efficient alternative for greenhouse gas emission reduction, economic benefit, energy recovery, and land use reduction, although it was identified as the most expensive for investment and operating cost, while composting scenario was also an efficient alternative with quite economic benefit, low investment and operating cost, and high reduction of land use, although it was identified as existing greenhouse gas emission and no energy generation. Furthermore, the aim of this study was also to establish localized assessment methods that waste management agencies, environmental engineers, and environmental policy decision makers can use to quantify and compare the contribution to the impacts from different waste treatment options.     

An Improved Rating System for Assessing Surface Water Contamination Potential from MSW Landfills

Leachate emission from uncontrolled municipal solid waste landfills (referred to as waste sites in the present study) is a major threat to the environment and living beings in its vicinity. Surface water contamination potential resulting from leachate may be used as one of the criteria for prioritization of sites for remediation purposes. The existing hazard rating systems that prioritize waste sites considering surface water contamination potential as one of the criteria are mainly suited for the developed countries where these were developed initially. In developing countries like India, the set of conditions differ from those in developed countries, and therefore the existing systems may not be suitable for developing countries. Thus in the present study, an improved system is proposed to assess surface water contamination potential from MSW sites. The system is based on the concept of Source, Pathway and Receptor. The proposed system employs parameters derived from the review of existing rating systems and selects their best and worst values based on literature review, design standards and field conditions. The importance weights of the system parameters have been decided based on expert judgment using Delphi technique. Sensitivity analysis of the system shows that the improved system is more sensitive than the existing systems for the site conditions encountered in developing countries. Monte Carlo analysis of the proposed system confirms the spread of the scores obtained from the system over the full scale of 0–1000. The improved system is compared with existing systems by applying it to waste sites from metropolitan cities of India and performing clustering analysis on the rating scores. The clustering analysis shows that the rating scores from the improved system are less clustered as compared to the scores from the existing systems. This demonstrates that the improved system makes a better tool to distinctly prioritize the waste sites for remediation purpose.     

Assessment of potential impacts of municipal solid waste treatment alternatives by using life cycle approach: a case study in Vietnam

In Vietnam, most of municipal solid waste (MSW) is disposed of at open dumping and landfill sites, and the methane gas from waste is the un-ignorable source of greenhouse gas (GHG) emission. It is indispensable to explore the possibility for GHG mitigation in MSW management. The objective of this study was to estimate alternative waste treatment practices towards the GHG emission mitigation, energy consumption and generation, reduction of landfill volume, and various benefits for proposing the appropriate selection by scenario analyses for representative Vietnam’s cities. Impacts were calculated by utilizing life cycle assessment (LCA) method. A literature review survey on the current applicability of LCA database for assessing impacts from waste sector in developing countries, especially for Vietnam, was carried out. This study assessed the contribution of alternative solid waste treatment practices. The result showed that, except investment and operation costs, incineration with energy recovery seems the suitable alternative for treating waste from representative cities of Vietnam according to reduction of GHG emission and waste burden to landfill sites and energy recovery and generation. Besides, MSW composition was identified as an important factor directly influencing to impacts as well as other products and benefits of waste treatment alternatives. Reliable data on waste composition are indispensable for assessing to choose, improve, or plan the waste treatment practices towards sustainable development.     

Application of ANP and DEMATEL to evaluate the decision-making of municipal solid waste management in Metro Manila

A municipal solid waste management (MSW) expert group was consulted in order to mirror how government officials might reach an effective solution regarding municipal solid waste management in Metro Manila. A critical issue regarding this is how the expert group can better evaluate and select a favorable MSW management solution using a series of criteria. MSW management solution selection is a multiple criteria decision-making (MCDM) problem, which requires the consideration of a large number of complex criteria. A robust MCDM method should consider the interactions among these criteria. The analytic network process (ANP) is a relatively new MCDM method which can deal with all kinds of interactions systematically. The Decision Making Trial and Evaluation Laboratory (DEMATEL) not only can convert the relations between cause and effect of criteria into a structural model, but also can be used as a way to handle the inner dependences within a set of criteria. Hence, this paper applies an effective solution based on a combined ANP and DEMATEL method to assist the expert group evaluating different MSW management solutions. According to the results, the best solution is for each city to have its own type of thermal process technology and resource recovery facility before landfill rather than entering a joint venture with enterprises or going into build-operate-transfer projects in order to be able to construct thermal process technologies and resource recovery facilities.     

A Comprehensive Numerical Model Simulating Gas,Heat, and Moisture Transport in Sanitary Landfills and Methane Oxidation in Final Covers

A model to simulate gas, heat, and moisture transport through a sanitary landfill has been developed. The model not only considers the different processes that go on in a landfill but also the oxidation of methane in the final cover. The model was calibrated using published results and field data from a pilot scale landfill in Calgary. The model captures the physics of the different processes quite well. Simulations from the model show that waste permeability had a significant impact on the temperature, pressure distribution, and flux from a landfill. The presence of the final and intermediate covers enhanced the gas storage capacity of the landfill. Biodegradation of the waste was enhanced as the final cover minimized the atmospheric influences. In addition, the composition of landfill gas emitted to the atmosphere was significantly different from the composition of gas generated in landfill due to the presence of covers as some of the methane is oxidized to carbon dioxide. There was no significant benefit of using a final cover of higher depth. The presence and number of intermediate covers had an impact on gas flux and temperature distribution within a landfill.     

Seasonal analysis of the generation and composition of solid waste: potential use—a case study

Ensenada health officials lack pertinent information on the sustainable management of solid waste, as do health officials from other developing countries. The aims of this research are: (a) to quantify and analyze the household solid wastes generated in the city of Ensenada, Mexico, and (b) to project biogas production and estimate generation of electrical energy. The characterization study was conducted by socioeconomic stratification in two seasonal periods, and the biogas and electrical energy projections were performed using the version 2.0 Mexico Biogas Model. Per capita solid waste generation was 0.779?±?0.019 kg per person per day within a 98 % confidence interval. Waste composition is composed mainly of food scraps at 36.25 %, followed by paper and cardboard at 21.85 %, plastic at 12.30 %, disposable diapers at 6.26 %, and textiles at 6.28 %. The maximum capacity for power generation is projected to be 1.90 MW in 2019. Waste generated could be used as an intermediate in different processes such as recycling (41.04 %) and energy recovery (46.63 %). The electrical energy that could be obtained using the biogas generated at the Ensenada sanitary landfill would provide roughly 60 % of the energy needed for street lighting.     

Municipal solid waste management in Thailand and disposal emission inventory

The increasing municipal solid waste (MSW) generation along with the high fraction of organic waste and a common disposal of open dumping is the current scenario in many areas in Thailand. As a response to this problem, the country’s Pollution Control Department (PCD) aims to reduce the MSW generation rate to less than 1 kg/capita/day, increase the collection efficiency, and improve the recovery of recyclables. For many years, more than 60% of the solid waste disposal system in Thailand has been carried out by open dumping. According to the survey conducted by this study, in 2004 there were 425 disposal sites (95 landfills; 330 open dumps) in Thailand and an estimated methane emission of 115.4 Gg/year was generated based on this practice. It has been estimated that the anticipated methane emission in Thailand will rise from 115.4 Gg/year to 118.5 Gg/year if the largest open dumpsites in provinces with no existing landfill are upgraded to sanitary landfill; and it will increase to 193.5 Gg/year if the existing sanitary landfill is upgraded to integrated waste management facilities. Moreover, Bangkok metropolitan have the highest methane emission (54.83 Gg/year) among all the regions in Thailand. The methane emission forecast of 339 Gg/year by 2020 (based on LandGEM methodology) provides a stimulus to create a comprehensive plan to capture and utilize methane as an energy source.     

Municipal solid waste generation in growing urban areas in Africa: current practices and relation to socioeconomic factors in Jimma, Ethiopia

As one of cities in the developing countries, a rapid population growth and industrial activities pose many environmental challenges for Jimma city, Ethiopia. One aspect of urban growth posing a threat on sustainable development is poor solid waste management, which results in environmental pollution. The purpose of this study is to evaluate the quantity, composition, sources of waste generated, their current disposal practices, and to recommend appropriate management technologies. The total waste generated daily in Jimma city was ca. 88,000 kg, and the average per capita generation rate was 0.55?±?0.17 kg/capita/day. Eighty-seven percent of the waste was produced by households and 13% by institutions, and a negligible fraction (0.1%) was generated by street sweepings. During the rainy season, 40% more waste was generated than in the dry season because of the increased availability of agricultural food product. Further analysis showed that biodegradable organic waste constitutes 54% by weight with an average moisture content of 60% that falls within the required limits for composting. The nonbiodegradable components constitute 46% of which 30% of it was nonrecyclable material. Only 25% of the community uses municipal containers for disposal at the selected landfill site. Fifty-one percent of the households disposed their waste in individually chosen spots, whereas 22% burned their waste. Finally 2% of households use private waste collectors. The socioeconomic analysis showed that higher family income and educational status is associated more with private or municipal waste collection and less with the application of backyard or open dumping. These insights into generated waste and management practice in Jimma city allow making suggestions for improved collection, treatment, and disposal methods. A primary conclusion is that the biodegradable waste is a major fraction having suitable properties for recycling. As such an economic benefit can be obtained from this waste while avoiding the need for disposal.     

Analysis of multi-temporal landsat satellite images for monitoring land surface temperature of municipal solid waste disposal sites

This studypresents a remote sensing application of using time series Landsat satellite images for monitoring the Trail Road and Nepean municipal solid waste (MSW) disposal sites in Ottawa, Ontario, Canada. Currently, the Trail Road landfill is in operation; however, during the 1960s and 1980s, the city relied heavily on the Nepean landfill. More than 400 Landsat satellite images were acquired from the US Geological Survey (USGS) data archive between 1984 and 2011. Atmospheric correction was conducted on the Landsat images in order to derive the landfill sites’ land surface temperature (LST). The findings unveil that the average LST of the landfill was always higher than the immediate surrounding vegetation and air temperature by 4 to 10 °C and 5 to 11.5 °C, respectively. During the summer, higher differences of LST between the landfill and its immediate surrounding vegetation were apparent, while minima were mostly found in fall. Furthermore, there was no significant temperature difference between the Nepean landfill (closed) and the Trail Road landfill (active) from 1984 to 2007. Nevertheless, the LST of the Trail Road landfill was much higher than the Nepean by 15 to 20 °C after 2007. This is mainly due to the construction and dumping activities (which were found to be active within the past few years) associated with the expansion of the Trail Road landfill. The study demonstrates that the use of the Landsat data archive can provide additional and viable information for the aid of MSW disposal site monitoring.     

Monitoring of flow field based on stable isotope geochemical characteristics in deep groundwater

As circumstances of operating and maintenance activities for landfilling and composting in Tehran metropolis differ from those of cities in developed countries, it was concluded to have an environmental impact comparison between the current solid waste management (MSW) strategies: (1) landfill, and (2) composting plus landfill. Life cycle assessment (LCA) was used to compare these scenarios for MSW in Tehran, Iran. The Eco-Indicator 99 is applied as an impact assessment method considering surplus energy, climate change, acidification, respiratory effect, carcinogenesis, ecotoxicity and ozone layer depletion points of aspects. One ton of municipal solid waste of Tehran was selected as the functional unit. According to the comparisons, the composting plus landfill scenario causes less damage to human health in comparison to landfill scenario. However, its damages to both mineral and fossil resources as well as ecosystem quality are higher than the landfill scenario. Thus, the composting plus landfill scenario had a higher environmental impact than landfill scenario. However, an integrated waste management will ultimately be the most efficient approach in terms of both environmental and economic benefits. In this paper, a cost evaluation shows that the unit cost per ton of waste for the scenarios is 15.28 and 26.40 US$, respectively. Results show landfill scenario as the preferable option both in environmental and economic aspects for Tehran in the current situation.     

Evaluation of old landfills--a thermoanalytical and spectroscopic approach

Abandoned landfills and dumps, where untreated waste materials were deposited in the past, are a main anthropogenic source of relevant gaseous emissions. The determination of stability is a crucial target in the context of landfill risk assessment. FTIR spectroscopy and simultaneous thermal analysis in association with multivariate statistical methods were applied to landfill materials in order to get information on the kind of waste and its reactivity. The spectral and thermal patterns are fingerprints of the material. Industrial waste and the material from a 5-year-old reactor landfill were distinguished from the defined classes of mechanically-biologically treated ("MBT") waste and 30 to 40-year-old stable landfills containing municipal solid waste and construction waste ("LF") by a classification model based on soft independent modeling of class analogy (SIMCA). Degradation experiments were carried out with the fresh material originating from one MBT plant that was subjected to aerobic and anaerobic conditions in lab-scale reactors. These samples were compared to samples of one reactor landfill and to the landfill fraction from the MBT plant to demonstrate the efficiency of the biological pretreatment before final disposal. Prediction models that are based on spectral or thermal characteristics and the corresponding reference analyses were calculated by means of a partial least squares regression (PLS-R). The developed models of the biological oxygen demand (BOD) and the dissolved organic carbon (DOC) were based on spectral data, the models of the total organic carbon (TOC) and total nitrogen (TN) were based on thermal data (heat flow profiles and mass spectra of combustion gases). Preliminary results are discussed. The enthalpy of the materials decreases with progressing mineralization, whereas the enthalpy of the remaining organic matter increases. The ratio of the enthalpies was used as an indicator of stability. Selected samples comprising old landfills, a recent reactor landfill, MBT landfills and MBT materials were classified according to the calculated ratios.