下吸式气化炉处理城市生活垃圾

下吸式气化炉具有原料适应性好，燃气中焦油含量少的特点。使用下吸式气化炉对广州城市生活垃圾进行了空气气化实验，并对燃气成分、焦油含量和灰渣重金属含量进行了分析。分析结果表明：燃气气体热值可达4600kJ／m^3，燃气焦油含量为2．0g／m^3。另外，对灰渣中的金属成分也进行了分析。试验结果表明：下吸式气化炉是处理复杂城市生活垃圾的一种有效手段。     

上吸式固定床生活垃圾气化炉气化特性研究

以福建某地区上吸式固定床生活垃圾气化炉(简称气化炉)为对象,分析垃圾在不同气化段温度(T)、空气当量比(ER)和料层高径比(H/D)条件下气化气成分和气化效率的影响。利用气相色谱分析垃圾气化产气特性,并设计正交试验分析气化炉最高气化效率的条件。结果表明:升高气化段温度可提高垃圾气化效率,但有一定局限;ER0.36后,风量超过气化炉自平衡能力,气化效率会迅速下降;H/D在3.0时气化效果最好。对于处理量为50t/d的气化炉(Φ3.0m×16.0m),在T为750℃、ER为0.36、H/D为3.0时,气化效率最高(79.3%);各影响因素中,ER的影响最大,T影响次之,H/D影响最小。气化气含焦油量为9.2~22.5g/m3,碳转化率为74.5%~85.9%。     

生活垃圾衍生燃料分段催化气化

利用下吸式分段催化固定床反应器对生活垃圾衍生燃料进行了气化实验。研究了气化温度、当量空气系数、气化介质和催化剂对气化产物的影响。结果表明,生活垃圾衍生燃料以塑料、纸类和厨余组分为主,热值在10 MJ·kg~(-1)以上,适合直接气化。随着气化温度升高,气化气中H_2和CO的含量、产气率、气化气热值、碳转化率和冷煤气效率升高,而焦油和CO_2含量明显降低;随着当量空气系数升高,CO_2含量、产气率和碳转化率升高,而焦油含量和气化气热值降低,在当量空气系数为0.33时冷煤气效率最高;当采用富氧空气作为气化介质时,N_2对于气化气的稀释作用减弱;添加催化剂能有效减少气化气中焦油的含量,提高H_2和CO的含量。采用下吸式分段催化气化,能有效提高气化气品质和冷煤气效率。     

生活垃圾高温空气气化处理的低污染特性分析

本文介绍了高温空气气化城市生活垃圾的工作原理及过程 ,分析了城市生活垃圾高温气化反应机理。通过对高温空气 /蒸汽发生器、高温气化炉及湿式除尘器等关键部件的分析发现 ,采用高温空气气化系统可实现城市生活垃圾低污染处理     

流化床生物质气化过程的中试研究

在流化床生物质气化炉内 ,用空气进行气化生物质 (花生壳 )的试验研究 ,分析的参数是ER(0 .2— 0 .45 ) ,气化床的温度 (75 0— 85 0℃ )。当当量比ER在 0 .2 5— 0 .33范围内 ,气化燃气热值为 6 .2— 6 .8MJ/Nm3,气体产量在 2 6 0—30 0Nm3/h。并对七种农、林废弃物进行了初步气化实验研究。生成的燃气成分 :CO在 14%— 17%之间 ,H2 含量一般低于10 % ,甲烷含量为 5 %— 10 %。燃气热值多数在 5 30 0— 6 5 0 0kJ/Nm3,气化效率 72 .6 %。实验结果表明 ,流化床生物质气化炉可用于生物质气化     

流化床生物质气化过程的中试研究

在流化床生物质气化炉内，用空气进行气化生物质（花生壳）的试验研究，分析了参数是ER（0.2-0.45)，气化床的温度750－850℃），当当量比ER在0.25-0.33范围内，气化燃气热值为6．2％－6.8MJ/Nm^3，气体产量在260－300Nm^3/h，并对七膛，林废弃物进行了初步实验研究，生成的燃气成分：CO在14％－17％之间，H2含量一般低于10％，甲烷含量为5％－10％，燃气热值多数在5300－6500kJ/Nm^3，气化效率72．6％，实验结果表明，流化床生物质气化炉可用于生物质气化。     

生物垃圾高温空气气化处理的低污染特性分析

本文介绍了高温空气气化城市生活垃圾的工作原理及过程,分析了城市生活垃圾高温气化反应机理。通过对高温空气／蒸汽发生器、高温气化炉及湿式除尘器等关键部件的分析发现,采用高温空气气化系统可实现城市生活垃圾低污染处理。     

医疗垃圾热解焚烧实验研究

医疗垃圾是一种对环境危害极大的危险废弃物.用一种固定炉排炉热解焚烧系统,对广州市部分医院的医疗垃圾进行了热解焚烧及尾气净化试验,并对焚烧工况、烟气中主要的污染物含量及灰渣的灼减率进行分析.分析结果表明:稳定运行时炉膛平均温度在850℃左右,二燃室平均温度在1000℃以上;尾气中CO、NOx、HCl和SO2浓度分别为:71mg/m3、125 mg/m3、27.8 mg/m3和21 mg/m3,灰渣的灼减率为2.7%.均远远低于标准限值.     

天然气全氧燃烧尾气生活垃圾气化热力学分析

基于Aspen Plus模拟平台,运用吉布斯能最小化原理,以天然气全氧燃烧尾气(后续称为烟气)作为气化剂,选取反应温度和烟气流量与生活垃圾量比(E/M)作为影响因素,气化炉温度变化范围为400~1 500℃,E/M范围0~3.0,对几种典型生活垃圾(木屑、纸屑、塑料、橡胶和厨余)气化进行模拟计算。模拟结果表明,以烟气作为生活垃圾气化剂,可制备富氢产品气,产品气为中热值燃气。温度在800℃左右时,H2的体积分数达到峰值46.75%,反应温度大于800℃时,反应温度的增加对提升产品气的热值、CO的含量有一定作用,但H2的含量和产品气产率有所下降,反应温度过高增加气化的能源投入,反应温度应控制在800~1 000℃范围。高温烟气的过量导致产品气热值和品质下降,E/M宜控制在0.4~1.0区间范围。     

回转窑式纯氧熔融焚烧垃圾技术研究

生活垃圾安全无害化处理是目前迫切需要解决的问题,直接气化熔融焚烧垃圾技术以降低二恶英排放方面巨大优势得到广泛关注,在此基础上提出纯氧熔融焚烧垃圾技术,几乎可以实现所有二次污染物近零排放。以350 t/d回转窑垃圾焚烧炉为例,对纯氧代替空气应用在回转窑上熔融焚烧垃圾系统进行了详细热力计算及分析。结果表明,纯氧熔融焚烧垃圾系统的锅炉效率可达90.56%,回转窑熔融焚烧系统还可以在垃圾焚烧后灰渣达到熔融温度的条件下,保持该系统热量平衡,稳定燃烧。并参考回转窑设计标准对该纯氧熔融焚烧城市生活垃圾的回转窑参数进行确定。     

Chloroaromatic pollutants in mussels incubated in two finnish watercourses polluted by industry

Concentrations of different chlorinated compounds were measured in mussels incubated in two polluted watercourses, a river (the River Kymijoki) and a lake (Lake Vanaja) for four weeks in summer 1995. The sum concentrations of polychlorinated phenols (PCP) and biphenyls (PCB) were both about 1 μg/g lipid weight (lw) in Lake Vanaja mussels, while in the River Kymijoki mussels PCPs were non-detectable and PCBs were measured 120 ng/g lIw. The concentrations of toxic polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners ranged between <17 and 370 pg/g Iw in Lake Vanaja mussels and between <38 and 11,000 pg/g lw in the River Kymijoki mussels. Polychlorinated diphenyl ethers (PCDE) were detected in the mussels incubated in the River Kymijoki (0.4–1.1 ng/g Iw), but not in those incubated in Lake Vanaja. Polychlorinated phenoxyanisoles (PCPA) were measured 33 ng/g lw and polychlorinated phenoxyphenols (PCPP) 300 ng/g lw in the mussels incubated in the River Kymijoki. PCPAs were also detected in reference samples, which were sediment and pike from the River Kymijoki and Baltic salmon, seal and white-tailed sea eagle.     

Book review

The Pesticide Manual ‐ A World Compendium, 8th Edition, C.R. Worthing, Editor and S.B. Walker, Assistant Editor, British Crop Protection Council, BCPC Publications Sales, Bear Farm, Binfield, Bracknell, Berkshire RG12 5QE, England. 1987, 1100 pp., UK £50; Overseas £56. ISBN 0–948404–01–9.     

Organochlorine compounds in a three-step terrestrial food chain

The concentrations of 15 organochlorine chemicals (PCBs and pesticides) were studied in a Central European oak wood food chain system: Great tit (Parus major), caterpillars (Tortrix viridana, Operophtera brumata, Erannis defoliaria), and oak-leaves (Quercus robur). Juvenile tits receive organochlorines from the mother via egg transfer and, eventually to a greater extent, from the caterpillar food source during nestling period. The concentrations of PCB 153 (2,2′,4,4′,5,5′-hexachlorobiphenyl, the most abundant in this study) was found in leaf material at ca. 1 ng/g, in caterpillars 10 ng/g, and in bird eggs 170 ng/g on an average and on a dry mass basis.     

The chemical stability of formulations of some hydrolyzable insecticides in aqueous mixtures with hydrolysis catalysts

Abstract

The active ingredients in commercial formulations of malathion, oxamyl, carbaryl, diazinon, and chlorpyrifos diluted to “spray tank”; concentrations with buffered distilled or natural water of pH 4–9 were stable for at least 24 hr. Formulations of trichlorfon were not stable at pH 7 or above but disappearance rates were slower than for the pure chemical in homogeneous solution. Cupric ion was observed to be an effective catalyst for the hydrolysis of a variety of pure organophosphorus insecticides but did not catalyze hydrolysis of the active ingredients of the formulations examined. Increasing the dilution of the formulation increased the susceptibility of malathion, oxamyl, and carbaryl to hydrolysis.     

Observations on the influence of water and soil pH on the persistence of insecticides

Abstract

The pH‐disappearance rate profiles were determined at ca. 25°C for 24 insecticides at 4 or 5 pH values over the range 4.5 to 8.0 in sterile phosphate buffers prepared in water‐ethanol (99: 1 v/v). Half‐lives measured at pH 8 were generally smaller than at lower pH values. Changes in half lives between pH 8.0 and 4.5 were largest (>1000x) for the aryl carbamates, carbofuran and carbaryl, the oxime carbamate, oxamyl, and the organophosphorus insecticide, trichlorfon. In contrast, half lives of phorate, terbufos, heptachlor, fensulfothion and aldicarb were affected only slightly by pH changes. Under the experimental conditions described half lives at pH8 varied from 1–2 days for trichlorfon and oxamyl to >1 year for fensulfothion and cyper‐methrin. Insecticide persistence on alumina (acid, neutral and basic), mineral soils amended with aluminum sulfate or calcium hydroxide to different pH values and four natural soils of different pH was examined. No correlation was observed between the measured pH of these solids and the rate of disappearance of selected insecticides applied to them. These observations demonstrate the difficulty of extrapolating the pH dependent disappearance behaviour observed in homogeneous solution to partially solid heterogeneous systems such as soil.     

Radionuclides in pinon pine (Pinus edulis) nuts from los alamos national laboratory lands and the dose from consumption

Abstract

One of the dominant tree species growing within and around the eastern portion of Los Alamos National Laboratory (LANL), Los Alamos, NM, lands is the pinon pine (Pinus edulis). Pinon pine is used for firewood, fence posts, and building materials and is a source of nuts for food—the seeds are consumed by a wide variety of animals and are also gathered by people in the area and eaten raw or roasted. This study investigated the (1) concentration of ³H, ¹³⁷Cs, ⁹⁰Sr, ^totU, ²³⁸Pu, ^{239, 240}Pu, and²⁴¹ Am in soils (0‐ to 12‐in. [31 cm] depth underneath the tree), pinon pine shoots (PPS), and pinon pine nuts (PPN) collected from LANL lands and regional background (BG) locations, (2) committed effective dose equivalent (CEDE) from the ingestion of nuts, and (3) soil to PPS to PPN concentration ratios (CRs). Most radionuclides, with the exception of ³H in soils, were not significantly higher (p < 0.10) in soils, PPS, and PPN collected from LANL as compared to BG locations, and concentrations of most radionuclides in PPN from LANL have decreased over time. The maximum net CEDE (the CEDE plus two sigma minus BG) at the most conservative ingestion rate (10 lb [4.5 kg]) was 0.0018 mrem (0.018 μSv); this is far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem (1000 μSv). Soil‐to‐nut CRs for most radionuclides were within the range of default values in the literature for common fruits and vegetables.     

Degradation and sorption of imidacloprid in dissimilar surface and subsurface soils

Degradation and sorption/desorption are important processes affecting the leaching of pesticides through soil. This research characterized the degradation and sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine) in Drummer (silty clay loam) and Exeter (sandy loam) surface soils and their corresponding subsurface soils using sequential extraction methods over 400 days. By the end of the incubation, approximately 55% of imidacloprid applied at a rate of 1.0 mg kg^?1 degraded in the Exeter sandy loam surface and subsurface soils, compared to 40% of applied imidacloprid within 300 days in Drummer surface and subsurface soils. At the 0.1 mg kg^?1 application rate, dissipation was slower for all four soils. Water-extractable imidacloprid in Exeter surface soil decreased from 98% of applied at day 1 to > 70% of the imidacloprid remaining after 400 d, as compared to 55% in the Drummer surface soil at day 1 and 12% at day 400. These data suggest that imidacloprid was bioavailable to degrading soil microorganisms and sorption/desorption was not the limiting factor for biodegradation. In subsurface soils > 40% of ¹⁴C-benzoic acid was mineralized over 21 days, demonstrating an active microbial community. In contrast, cumulative ¹⁴CO₂ was less than 1.5% of applied ¹⁴C-imidacloprid in all soils over 400 d. Qualitative differences in the microbial communities appear to limit the degradation of imidacloprid in the subsurface soils.     

Evaluation of trichloroethene recovery processes in heterogeneous aquifer cells flushed with biodegradable surfactants

The ability of two biodegradable surfactants, polyoxyethylene (20) sorbitan monooleate (Tween 80) and sodium dihexyl sulfosuccinate (Aerosol MA), to recover a representative dense non-aqueous-phase liquid (DNAPL), trichloroethene (TCE), from heterogeneous porous media was evaluated through a combination of batch and aquifer cell experiments. An aqueous solution containing 3.3% Aerosol MA, 8% 2-propanol and 6 g/l CaCl(2) yielded a weight solubilization ratio (WSR) of 1.21 g TCE/g surfactant, with a corresponding liquid-liquid interfacial tension (IFT) of 0.19 dyn/cm. Flushing of aquifer cells containing a TCE-DNAPL source zone with approximately two pore volumes of the AMA formulation resulted in substantial (>30%) mobilization of TCE-DNAPL. However, a TCE mass recovery of 81% was achieved when the aqueous-phase flow rate was sufficient to displace the mobile TCE-DNAPL toward the effluent well. Aqueous solutions of Tween 80 exhibited a greater capacity to solubilize TCE (WSR=1.74 g TCE/g surfactant) and exerted markedly less reduction in IFT (10.4 dyn/cm). These data contradict an accepted empirical correlation used to estimate IFT values from solubilization capacity, and indicate a unique capacity of T80 to form concentrated TCE emulsions. Flushing of aquifer cells with less than 2.5 pore volumes of a 4% T80 solution achieved TCE mass recoveries ranging from 66 to 85%, with only slight TCE-DNAPL mobilization (<5%) occurring when the total trapping number exceeded 2 x 10(-5). These findings demonstrate the ability of Tween 80 and Aerosol MA solutions to efficiently recover TCE from a heterogeneous DNAPL source zone, and the utility of the total trapping number as a design parameter for a priori prediction of DNAPL mobilization and bank angle formation when flushing with low-IFT solutions. Given their potential to stimulate microbial reductive dechlorination at low concentrations, these surfactants are well-suited for remedial action plans that couple aggressive mass removal followed by enhanced bioremediation to treat chlorinated solvent source zones.     

Biochemical interaction of six op delayed neurotoxicants with several neurotargets

Abstract

Five organophosphorous insecticides: Leptophos, EPN, Cyano‐fenphos, trichloronate and salithion proved to cause irreversible ataxia not only to chicken but also to mice and sheep. TOCP was included as a reference. Cyanofenphos blocked the catecholamine B‐receptor binding activity with ³H‐norepinephrine at a level similar to that of the specific inhibitor propranolol in the mouse heart preparation. In the lamb heart preparation, the B‐receptor was more sensitive to Leptophos, salithion and TOCP than to propranolol. The six compounds and their oxons were screened for their in‐vitro inhibition to monamine oxidase (MAO), acetyl cholinesterase (AChE) and neurotoxic esterase (NTE) in the brain of either mouse, lamb or chicken. It is believed that their AChE inhibition stands for their acute toxicity, while NTE inhibition is responsible for their paralytic ataxia.     

Phytoextraction of lead-contaminated soil using vetivergrass (<Emphasis Type="Italic">Vetiveria zizanioides</Emphasis> L.), cogongrass (<Emphasis Type="Italic">Imperata cylindrica</Emphasis> L.) and carabaograss (<Emphasis Type="Italic">Paspalum conjugatum</Emphasis> L.)

Background, Aims and Scope The global problem concerning contamination of the environment as a consequence of human activities is increasing. Most of the environmental contaminants are chemical by-products and heavy metals such as lead (Pb). Lead released into the environment makes its way into the air, soil and water. Lead contributes to a variety of health effects such as decline in mental, cognitive and physical health of the individual. An alternative way of reducing Pb concentration from the soil is through phytoremediation. Phytoremediation is an alternative method that uses plants to clean up a contaminated area. The objectives of this study were: (1) to determine the survival rate and vegetative characteristics of three grass species such as vetivergrass, cogongrass and carabaograss grown in soils with different Pb levels; and (2) to determine and compare the ability of the three grass species as potential phytoremediators in terms of Pb accumulation by plants. Methods The three test plants: vetivergrass (Vetiveria zizanioides L.); cogongrass (Imperata cylindrica L.); and carabaograss (Paspalum conjugatum L.) were grown in individual plastic bags containing soils with 75 mg kg⁻¹ (37.5 kg ha⁻¹) and 150 mg kg⁻¹ (75 kg ha⁻¹) of Pb, respectively. The Pb contents of the test plants and the soil were analyzed before and after experimental treatments using an atomic absorption spectrophotometer. This study was laid out following a 3 × 2 factorial experiment in a completely randomized design. Results On the vegetative characteristics of the test plants, vetivergrass registered the highest whole plant dry matter weight (33.85–39.39 Mg ha⁻¹). Carabaograss had the lowest herbage mass production of 4.12 Mg ha⁻¹ and 5.72 Mg ha⁻¹ from soils added with 75 and 150 mg Pb kg⁻¹, respectively. Vetivergrass also had the highest percent plant survival which meant it best tolerated the Pb contamination in soils. Vetivergrass registered the highest rate of Pb absorption (10.16 ± 2.81 mg kg⁻¹). This was followed by cogongrass (2.34 ± 0.52 mg kg⁻¹) and carabaograss with a mean Pb level of 0.49 ± 0.56 mg kg⁻¹. Levels of Pb among the three grasses (shoots + roots) did not vary significantly with the amount of Pb added (75 and 150 mg kg⁻¹) to the soil. Discussion Vetivergrass yielded the highest biomass; it also has the greatest amount of Pb absorbed (roots + shoots). This can be attributed to the highly extensive root system of vetivergrass with the presence of an enormous amount of root hairs. Extensive root system denotes more contact to nutrients in soils, therefore more likelihood of nutrient absorption and Pb uptake. The efficiency of plants as phytoremediators could be correlated with the plants’ total biomass. This implies that the higher the biomass, the greater the Pb uptake. Plants characteristically exhibit remarkable capacity to absorb what they need and exclude what they do not need. Some plants utilize exclusion mechanisms, where there is a reduced uptake by the roots or a restricted transport of the metals from root to shoots. Combination of high metal accumulation and high biomass production results in the most metal removal from the soil. Conclusions The present study indicated that vetivergrass possessed many beneficial characteristics to uptake Pb from contaminated soil. It was the most tolerant and could grow in soil contaminated with high Pb concentration. Cogongrass and carabaograss are also potential phytoremediators since they can absorb small amount of Pb in soils, although cogongrass is more tolerant to Pb-contaminated soil compared with carabaograss. The important implication of our findings is that vetivergrass can be used for phytoextraction on sites contaminated with high levels of heavy metals; particularly Pb. Recommendations and Perspectives High levels of Pb in localized areas are still a concern especially in urban areas with high levels of traffic, near Pb smelters, battery plants, or industrial facilities that burn fuel ending up in water and soils. The grasses used in the study, and particularly vetivergrass, can be used to phytoremediate urban soil with various contaminations by planting these grasses in lawns and public parks. ESS-Submission Editor: Dr. Willie Peijnenburg (wjgm.peijnenburg@rivm.nl)