共查询到20条相似文献,搜索用时 62 毫秒
1.
污泥回流分离工艺(RSSP)除磷脱氮试验研究 总被引:1,自引:1,他引:0
介绍了一种新型的脱氮除磷工艺——回流污泥分离工艺(return sludge separate process),及其运行情况。该工艺在传统的厌氧缺氧好氧(A2/O)的模式下,针对硝酸盐对厌氧释磷的抑制问题进行改进,提出回流污泥的气浮浓缩分离方案,以提高系统的脱氮除磷效果。研究结果表明,在进水COD为250~400 mg/L,NH+4-N为30~45 mg/L,PO3-4-P为8~10 mg/L左右时,该工艺对NH+4-N和PO3-4-P的去除率分别可达79.3%和95%。该系统与A2/O的平行比较数据表明,该系统能够提高氮磷综合处理效率,解决A2/O处理工艺中存在无效释磷和硝酸根抑制问题。 相似文献
2.
A/O和A2/O工艺对膜生物反应器处理焦化废水影响的研究 总被引:3,自引:1,他引:2
为提高膜生物反应器对焦化废水的处理效果,采用A/O和A2/O两种工艺的膜生物反应器处理焦化废水,通过对比处理效果、分析膜污染情况,寻求膜生物反应处理焦化废水的最优工艺。实验结果表明:A2/O工艺系统对酚、NH3-N、COD的去除率分别为99%、90%和95%;A/O工艺系统对酚、NH3-N和COD的去除率分别为97%、75%和93%。A2/O膜生物反应器系统对焦化废水中NH3-N的去除效果明显优于A/O膜生物反应器系统,其反硝化率为50%~70%。对膜污染分析表明不同工艺对膜污染的影响不显著,A2/O工艺膜通量衰减59%,A/O工艺膜通量衰减56%。研究表明在膜生物反应器中,A2/O工艺对焦化废水的去除效果要优于A/O工艺。 相似文献
3.
为开发新型除磷脱氮工艺,研制了将MBR和A2/O工艺相结合的新型MB(A2/O)反应器。研究了MB(A2/O)反应器处理城市污水厌氧富磷上清液的化学除磷,并分析了过程机理及特性。结果表明:对于TP在30~45 mg/L的富磷上清液,采用含20% Ca(OH)2的工业石灰与P的最佳投加质量比为22.5;纯Ca(OH)2与P的最佳投加质量比为5.6(摩尔比为2.5);FeSO4·7H2O与P的最佳投加质量比为10.7(Fe2+与P的摩尔比为1.3);Al2(SO4)3·12H2O与P的最佳投加质量比为12(Al3+与P的摩尔比为1.3)时,均可使出水TP稳定在0.3 mg/L以下;以石灰、NaOH的联合投加方式可大幅减少石灰投加量。 相似文献
4.
超细粉煤灰基成型吸附剂的动态吸附实验 总被引:2,自引:1,他引:1
以粉煤灰为原料制备成型吸附剂,对水溶液中亚甲基蓝和Cr6+进行动态吸附研究,绘制穿透曲线,利用Origin软件对实验数据分析处理,得出穿透曲线的通式Ct=A1-A2〖〗1+(t/t0)p+A1。结果表明,初始浓度C0=25 mg/L,填料高度不同时,达到穿透点的时间随填料高度的增加而增加;填料高度h=200 mm,初始浓度不同时,达到穿透点的时间随初始浓度的增加而减小;该吸附剂对有机染料和重金属离子均有较好的吸附性能;穿透曲线通式的回归线性相关系数表明,该通式可很好地反映超细粉煤灰成型吸附剂的动态吸附过程。 相似文献
5.
SBR降解动力学研究 总被引:1,自引:0,他引:1
采用SBR工艺处理有机废水,在已有工艺条件下对生物降解动力学进行了研究,得出生物降解反应为一级反应。研究表明,用Monod公式能较好反映出有机物的降解规律,确定了其动力学参数Vmax=14.6306 d-1,Ks=83.2993 mg/L,得出SBR降解动力学模型为V=14.6306X·S/(83.2993+S)。利用以动力学为基础的动态模拟法优化SBR工艺,实验结果表明该方法合理可行,对SBR的设计与运行有一定的指导作用,可作为SBR反应器扩大实验和设计的依据。 相似文献
6.
7.
8.
针对厌氧氨氧化工艺需要提供充足的亚硝酸盐氮为电子受体的问题,利用培养基对SBR中具有一定短程硝化功能的污泥进行富集培养,得到氨氧化菌和亚硝酸盐氧化菌的数量之比为104︰1,并研究了工艺条件对短程硝化的影响,结果表明,适合氨氧化菌生长的最佳温度为30℃、pH为7.5、nHCO-3/nNH+4-N值为1。以适合氨氧化菌生长的最佳环境条件优化SBR,在进水氨氮浓度为250 mg/L时,氨氮的转化率达到90%以上,亚硝酸盐氮积累率维持在85%以上,反应器中氨氧化菌与亚硝酸盐氧化菌的数量之比为103∶1,亚硝酸盐的高效积累为厌氧氨氧化工艺处理高氨废水的过程提供了稳定的电子受体。 相似文献
9.
10.
碳酸根对磷酸钙沉淀反应回收磷的影响简 总被引:1,自引:0,他引:1
以模拟的厌氧消化液为处理对象,通过小试实验,考察不同初始磷浓度CP、Ca/P物质的量比、pH和温度下,碳酸根(CO32-)对磷酸钙沉淀反应回收磷的影响;利用扫描电镜(SEM)、X射线衍射仪(XRD)和傅里叶变换红外光谱(FTIR)对沉淀产物进行表征。结果表明,高浓度的CO32-对以磷酸钙沉淀反应去除和回收磷的效率影响较大;CP相同时,CO32-浓度(CCO32-)越大,P的去除率越低,低CP(20 mg/L)时尤为显著;当CCO32-相同时,随着CP的增大,反应速率加快,P的去除率逐渐升高,但升高幅度越来越小;增大Ca/P比和pH能提高P的去除率,降低CO32-对磷酸钙沉淀反应的抑制作用,综合考虑实际效果,应选择Ca/P比为3.33,pH为9.0作为适宜的反应条件;升高温度对降低CO32-对磷酸钙沉淀反应的抑制作用贡献不大。在CP为60 mg/L,Ca/P比为1.67,pH为9.0,温度为20℃的条件下,当C CO32-为0时,得到的沉淀产物主要为羟基磷灰石HAP;当C CO32-为30 mmol/L时,得到的沉淀产物为磷酸钙和碳酸合磷灰石的混合物。 相似文献
11.
造纸废水混凝处理中SFT助凝替代性研究 总被引:1,自引:0,他引:1
中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染 相似文献
12.
Janusz A. Pudykiewicz Anna S. Koziol 《Atmospheric environment (Oxford, England : 1994)》1998,32(24):5541
The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing. 相似文献
13.
Árpád Ambrus 《Journal of environmental science and health. Part. B》2013,48(3):435-442
Abstract A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits. 相似文献
14.
介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠 相似文献
15.
活性炭三维电极法对印染废水的处理研究 总被引:4,自引:0,他引:4
对三维电极方法处理印染废水进行了实验研究,初步探讨了活性炭三维电极法处理印染废水的机理,对影响处理效果的各种要素,如反应时间、槽电压和pH值等进行了条件实验,得出了活性炭三维电极法处理印染废水的最佳运行条件为:停留时间120-180 min,槽电压25~30 V,进水pH值6.5~7.5。结果表明,该反应器能有效地降低废水色度,有较高的COD去除效率,并能提高印染废水的可生化性。 相似文献
16.
不同泥源对厌氧氨氧化反应器启动的影响 总被引:2,自引:1,他引:1
采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。 相似文献
17.
18.
以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径<1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径. 相似文献
19.
Volker Berding Stefan Schwartz Michael Matthies 《Environmental science and pollution research international》1999,6(1):37-43
The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters
(inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation,
on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency.
The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity
was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters),
and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity
to 961, and the maximal dimension is 21. 相似文献