Explosibility of cork dust in methane/air mixtures

Explosibility studies of hybrid methane/air/cork dust mixtures were carried out in a near-spherical 22.7 L explosibility test chamber, using 2500 J pyrotechnic ignitors. The suspension dust burned as methane/air/dust clouds and the uniformity of the cork dust dispersion inside the chamber was evaluated through optical dust probes and during the explosion the pressure and the temperature evolution inside the reactor were measured. Tested dust particles had mass median diameter of 71.3 μm and the covered dust cloud concentration was up to 550 g/m³. Measured explosions parameters included minimum explosion concentration, maximum explosion pressures and maximum rate of pressure rise. The cork dust explosion behavior in hybrid methane/air mixtures was studied for atmospheres with 1.98 and 3.5% (v/v) of methane. The effect of methane content on the explosions characteristic parameters was evaluated. The conclusion is that the risk and explosion danger rises with the increase of methane concentration characterized by the reduction of the minimum dust explosion concentration, as methane content increases in the atmosphere. The maximum explosion pressure is not very much sensitive to the methane content and only for the system with 3.5% (v/v) of methane it was observed an increase of maximum rate of pressure rise, when compared with the value obtained for the air/dust system.     

Effect of spark duration on explosion parameters of methane/air mixtures in closed vessels

The paper outlines an experimental study on influence of the spark duration and the vessel volume on explosion parameters of premixed methane–air mixtures in the closed explosion vessels. The main findings from these experiments are: For the weaker ignition the spark durations in the range from 6.5 μs to 40.6 μs had little impact on explosion parameters for premixed methane–air mixtures in the 5 L vessel or 20 L vessel; For the same ignitions and volume fractions of methane in air the explosion pressures and the flame temperatures in both vessels of 5 L and 20 L were approximately the same, but the rates of pressure rises in both vessels of 5 L and 20 L were different; The explosion indexes obtained from the measured pressure time histories for both vessels of 5 L and 20 L were approximately equal; For the weaker ignition with the fixed spark duration 45 μs the ignition energies in the range from 54 mJ to 430 mJ had little impact on the explosion parameters; For the same ignition and the volume fractions of methane in air, the vessel volumes had a significant impact on the flame temperatures near the vessel wall; The flame temperatures near the vessel wall decreased as the vessel volumes increased.     

Methane/coal dust/air explosions and their suppression by solid particle suppressing agents in a large-scale experimental tube

Methane/coal dust/air explosions under strong ignition conditions have been studied in a 199 mm inner diameter and 30.8 m long horizontal tube. A fuel gas/air manifold assembly was used to introduce methane and air into the experimental tube, and an array of 44 equally spaced dust dispersion units was used to disperse coal dust particles into the tube. The methane/coal dust/air mixture was ignited by a 7 m long epoxypropane mist cloud explosion. A deflagration-to-detonation transition (DDT) was observed, and a self-sustained detonation wave characterized by the existence of a transverse wave was propagated in the methane/coal dust/air mixtures.The suppressing effects on methane/coal dust/air mixture explosions of three solid particle suppressing agents have been studied. Coal dust and the suppressing agent were injected into the experimental tube by the dust dispersion units. The length of the suppression was 14 m. The suppression agents examined in this study comprised ABC powder, SiO₂ powder, and rock dust powder (CaCO₃). Methane/coal dust/air explosions can be efficiently suppressed by the suppression agents characterized by the rapid decrease in overpressure and propagating velocity of the explosion waves.     

Effects of hydrogen addition on propagation characteristics of premixed methane/air flames

An experimental study has been conducted to investigate the effects of hydrogen addition on the fundamental propagation characteristics of methane/air premixed flames at different equivalence ratios in a venting duct. The hydrogen fraction in the methane–hydrogen mixture was varied from 0 to 1 at equivalence ratios of 0.8, 1.0 and 1.2. The results indicate that the tendency towards flame instability increased with the fraction of hydrogen, and the premixed hydrogen/methane flame underwent a complex shape change with the increasing hydrogen fraction. The tulip flame only formed when the fraction of hydrogen ranged from 0 to 50% at an equivalence ratio of 0.8. It was also found that the flame front speed and the overpressure increased significantly with the hydrogen fraction. For all equivalence ratios, the stoichiometric flame (Φ = 1.0) has the shortest time of flame propagation and the maximum overpressure.     

Experimental study on vented gas explosion in a cylindrical vessel with a vent duct

A study of vented explosions in a length over diameter (L/D) of 2 in cylindrical vessel connecting with a vent duct (L/D = 7) is reported. The influence of vent burst pressure and ignition locations on the maximum overpressure and flame speeds at constant vent coefficient, K of 16.4 were investigated to elucidate how these parameters affect the severity of a vented explosion. Propane and methane/air mixtures were studied with equivalence ratio, Φ ranges from 0.8 to 1.6. It is demonstrated that end ignition exhibited higher maximum overpressures and flame speeds in comparison to central ignition, contrary to what is reported in literature. There was a large acceleration of the flame toward the duct due to the development of cellular flames and end ignition demonstrated to have higher flame speeds prior to entry into the vent due to the larger flame distance. The higher vent flow velocities and subsequent flame speeds were responsible for the higher overpressures obtained. Rich mixtures for propane/air mixtures at Φ = 1.35 had the greatest flame acceleration and the highest overpressures. In addition, the results showed that Bartknecht's gas explosion venting correlation is grossly overestimated the overpressure for K = 16.4 and thus, misleading the impact of the vent burst pressure.     

开口钢管内甲烷爆炸火焰厚度和压力发展特征

通过搭建长为20m、截面为0.08m×0.08m的非绝热开口钢管,研究了甲烷与空气预混气体发生爆炸后的火焰和压力发展特征。实验结果表明:火焰信号最强的时刻对应于火焰前锋反应区内某时刻,而火焰信号起始上升时刻与火焰前锋预热区起始时刻接近,应选择某点火焰信号起始上升时刻作为该点的火焰到达时间。随着远离点火源距离的增加,火焰厚度呈现先变薄后变厚的变化趋势,最大超压呈现先减小、后增大、再减小的趋势,火焰传播速度则呈先增大后减小的变化过程。非绝热开口钢管的实验条件对爆炸超压和火焰传播速度的影响较大。研究成果可为甲烷爆炸致灾机制及防控的研究提供参考。     

Experiments on the influence of pre-ignition turbulence on vented gas and dust explosions

Experiments were performed on the influence of pre-ignition turbulence on the course of vented gas and dust explosions. A vertical cylindrical explosion chamber of approximately 100 l volume and a length-to-diameter ratio (l/d) of 4.7 consisting of a steel bottom segment and three glass sections connected by steel flanges was used to perform the experiments. Sixteen small fans evenly distributed within the chamber produced turbulent fluctuations from 0 to 0.45 m/s. A Laser-Doppler-anemometer (LDA) was used to measure the flow and turbulence fields. During the experiments the pressure and in the case of dust explosions the dust concentration were measured. In addition, the flame propagation was observed by a high-speed video camera. A propane/nitrogen/oxygen mixture was used for the gas explosion experiments, while the dust explosions were produced by a cornstarch/air mixture.It turned out that the reduced explosion pressure increased with increasing turbulence intensity. This effect was most pronounced for small vents with low activation pressures, e.g. for bursting disks made from polyethylene foil. In this case, the overpressure at an initial turbulence of 0.45 m/s was twice that for zero initial turbulence.     

Enhancement effects of methane/air explosion caused by water spraying in a sealed vessel

Experiments about the influence of ultrafine water mist on the methane/air explosion were carried out in a fully sealed visual vessel with methane concentrations of 8%, 9.5%, 11% and 12.5%. Water mists were generated by two nozzles and the droplets' Sauter Mean Diameters (SMD) were 28.2 μm and 43.3 μm respectively which were measured by Phase Doppler Particle Anemometer (PDPA). A high speed camera was used to record the flame propagation processes. The results show that the maximum explosion overpressure, pressure rising rate and flame propagation velocity of methane explosions in various concentrations increased significantly after spraying. Furthermore, the brightness of explosion flame got much higher after spraying. Besides, the mist with a larger diameter had a stronger turbulent effect and could lead to a more violent explosion reaction.     

Flame propagation in hybrid mixture of coal dust and methane

To investigate the flame propagation through hybrid mixture of coal dust and methane in a combustion chamber, a high-speed video camera with a microscopic lens and a Schlieren optical system were used to record the flame propagation process and to obtain the direct light emission photographs. Flame temperature was detected by a fine thermocouple. The suspended coal dust in the mixture of methane and air was ignited by an electric spark. The flame propagation speeds and maximum flame temperatures of the mixture were analyzed. The results show that the co-presence of coal dust and methane improves the flame propagation speed and maximum flame temperature notably, which become much higher than that of the single-coal dust flame. The flame front temperature varies with the coal dust concentration.     

Explosions and deflagration-to-detonation transitions in epoxy propane/air mixtures

The explosion and deflagration-to-detonation transition (DDT) in epoxy propane (E.P.) vapor/air mixture clouds under weak ignition conditions has been studied in an experimental tube of diameter 199 mm and length 29.6 m. E.P. vapor clouds were formed by injecting liquid E.P. into the experimental tube and evaporating of the fine E.P. droplets. The dimension and the evaporating process of the E.P. droplet were measured and analyzed. The E.P. vapor/air mixture clouds were ignited by an electric spark with an ignition energy of 40 J. The characteristics and the stages of the DDT process in the E.P. vapor/air mixtures have been studied and analyzed. A self-sustained detonation wave formed, as was evident from the existence of a transverse wave and a cellular structure. Moreover, a retonation wave formed during the DDT process in the E.P. vapor/air mixture. The influence of the E.P. vapor concentration on the DDT process has been studied. The minimum E.P. vapor concentration for the occurrence of the DDT in the E.P. vapor/air mixture has been evaluated and the variation of DDT distance with E.P. vapor concentration has been analyzed.     

Influence of coal particles on methane/air mixture ignition in a heated environment

The temperature at which coal dust glows is normally much lower than the auto-ignition temperature (AIT) of methane/air mixtures, and thus a better understanding is needed regarding methane/air ignition in a heated environment in the presence of coal particles. A horizontal tube apparatus was used to test the effect of brown coal and two kinds of bituminous and anthracite on methane/air combustibility. For the four coal samples tested, the presence of coal particles significantly reduced the minimum temperature for ignition of methane/air mixtures in a heated environment. No. 1 bituminous coal with 12 mm diameter decreased the ignition temperature value from 595 to 500 °C. It is thought that pre-ignition of low-AIT volatiles emitted from the heated coal particles ignited the methane/air mixtures. Volatiles, sulfur content, and large porosity of piled coal particles all enhanced ignition of methane/air mixtures in a hot environment, while water content and small particle size reduced ignition. For anthracite, no ignition occurred when temperatures of the heated environment were lower than the AIT of methane (595 °C), except for the 12-mm-diameter sample. Anthracite did not readily ignite methane/air mixtures and the ignition mechanism was somewhat similar to that of a burning cigarette.     

Effects of obstacles and deposited coal dust on characteristics of premixed methane–air explosions in a long closed pipe

An experimental system including pressure transducer, electric spark ignition device, data acquisition and control unit was set up to investigate methane–air explosions in a horizontal pipe closed at both ends with or without the presence of obstacles and deposited coal dust. The experimental results show that explosion characteristics depended on the methane content, on the layout of obstacles, and on the deposited coal dust. Pressure fluctuation with a frequency of 150 Hz appeared in its crest when the methane content was close to the stoichiometric ratio (9.5% methane percentage by volume). The pressure rise rate increased locally when a single obstacle was mounted in the pipe, but it had little effect on the pressure peak. Repeated obstacles mounted in the pipe caused the pressure to rise sharply, and the mean maximum explosion overpressure increased with the increase of the obstacle’s number. The amplitude of pressure fluctuation was reduced when deposited coal dust was paved in the bottom of the pipe. However, when repeated obstacles were arranged inside, the maximum overpressures were higher with coal dust deposited than pure gas explosions.     

Methane–air mixtures ignited by CW laser-heated targets on optical fiber tips: Comparison of targets,optical fibers,and ignition delays

Fiber optic systems are being deployed in locations where explosive gas atmospheres are normally present or are present under fault conditions. The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory (NIOSH, PRL) conducted a study of laser safety in potentially flammable environments. Researchers conducted experiments to estimate the mean and standard deviation of laser powers needed to ignite 6% methane–air atmospheres using single mode optical fiber tips covered by two types of iron oxide (Fe₃O₄ and (FeMn)₂O₃) mixed with a ceramic adhesive. The iron oxides, heated by a 1064 nm continuous wave laser, ignited the methane–air mixtures at similar powers. The minimum igniting power and maximum non-igniting power (10 tests) were 407 and 350 mW, respectively, using a 62.5 μm fiber. Laser beams guided by 125 and 80 μm diameter cladding single mode fibers produced similar methane–air igniting powers. Ignition was not observed using coal particles at powers that produced ignition with the iron oxides. Threshold ignition delays using the single mode fiber were approximately proportional to the inverse square of the igniting power. Ignition delays were significantly longer than the reported activation time for a commercial fiber optic power limiter. Comparisons are made with the results of other researchers.     

Numerical studies on minimum ignition energies in methane/air and iso-octane/air mixtures

In this study, the dependence of minimum ignition energies (MIE) on ignition geometry, ignition source radius and mixture composition is investigated numerically for methane/air and iso-octane/air mixtures. Methane and iso-octane are both important hydrocarbon fuels, but differ strongly with respect to their Lewis numbers. Lean iso-octane air mixtures have particularly large Lewis numbers. The results show that within the flammability limits, the MIE for both mixtures stays almost constant, and increases rapidly at the limits. The MIEs for both fuels are also similar within the flammability limits. Furthermore, the MIEs of iso-octane/air mixtures with a small spherical ignition source increase rapidly for lean mixtures. Here the Lewis number is above unity, and thus, the flame may quench because of flame curvature effects. The observations show a distinct difference between ignition and flame propagation for iso-octane. The minimum energy required for initiating a successful flame propagation can be considerably higher than that required for initiating an ignition in the ignition volume. For iso-octane with a small spherical ignition source, this effect was observed at all equivalence ratios. For iso-octane with cylindrical ignition sources, the phenomenon appeared at lower equivalence ratios only, where the mixture's Lewis number is large. For methane fuel, the effect was negligible. The results highlight the significance of molecular transport properties on the decision whether or not an ignitable mixture can evolve into a propagating flame.     

Large scale experiments to study fires following the rupture of high pressure pipelines conveying natural gas and natural gas/hydrogen mixtures

As part of the EC funded Naturalhy project, two large scale experiments were conducted to study the hazard presented by the rupture of high pressure transmission pipelines conveying natural gas or a natural gas/hydrogen mixture containing approximately 22% hydrogen by volume. The experiments involved complete rupture of a 150 mm diameter pipeline pressurised to nominally 70 bar. The released gas was ignited and formed a fireball which rose upwards and then burned out. It was followed by a jet fire which continued to increase in length, reaching a maximum of about 100 m before steadily declining as the pipeline depressurised. During the experiments, the flame length and the incident radiation field produced around the fire were measured. Measurements of the overpressure due to pipeline rupture and gas ignition were also recorded. The results showed that the addition of the hydrogen to the natural gas made little difference to radiative characteristics of the fires. However, the fraction of heat radiated by these pipeline fires was significantly higher than that observed for above ground high pressure jet fires (also conducted as part of the Naturalhy project) which achieved flame lengths up to 50 m. Due to the lower density, the natural gas/hydrogen mixture depressurised more quickly and also had a slightly reduced power. Hence, the pipeline conveying the natural gas/hydrogen mixture resulted in a slightly lower hazard in terms of thermal dose compared to the natural gas pipeline, when operating at the same pressure.     

Investigations of flame front propagation between interconnected process vessels. Development of a new flame front propagation time prediction model

For the case where a dust or gas explosion can occur in a connected process vessel, it would be useful, for the purpose of designing protection measures and also for assessing the existing protection measures such as the correct placement, to have a tool to estimate the time for flame front propagation along the connecting pipe. Measurements of data from large-scale explosion tests in industrially relevant process vessels are reported. To determine the flame front propagation time, either a 1 m³ or a 4.25 m³ primary process vessel was connected via a pipe to a mechanically or pneumatically fed 9.4 m³ secondary silo. The explosion propagation started after ignition of a maize starch/air mixture in the primary vessel. No additional dust was present along the connecting pipe. Systematic investigations of the explosion data have shown a relationship between the flame front propagating time and the reduced explosion over-pressure of the primary explosion vessel for both vessel volumes. Furthermore, it was possible to validate this theory by using explosion data from previous investigations. Using the data, a flame front propagation time prediction model was developed which is applicable for:

• •gas and dust explosions up to a K value of 100 and 200 bar m s⁻¹, respectively, and a maximum reduced explosion over-pressure of up to 7 bar;
• •explosion vessel volumes of 0.5, 1, 4.25 and 9.4 m³, independent of whether they are closed or vented;
• •connecting pipes of pneumatic systems with diameters of 100–200 mm and an air velocity up to 30 m s⁻¹;
• •open ended pipes and pipes of interconnected vessels with a diameter equal to or greater than 100 mm;
• •lengths of connecting pipe of at least 2.5–7 m.

     

Experimental research on methane/air explosion inhibition using ultrafine water mist containing methane oxidizing bacteria

In order to deeply understand the inhibitory effect of ultrafine water mist containing methane-oxidizing bacteria on methane explosion, a small-sized semi-closed visual experimental platform was built. Five different application mist amounts (0.7 mL, 2.1 mL, 3.5 mL, 4.9 mL, 6.3 mL) of ultrafine water mist containing methane-oxidizing bacteria on 9.5% methane explosion were studied experimentally. Ultrafine water mist was generated by the ultrasonic atomization generator, and mist size was measured by a winner319 laser particle size analyzer. During the methane explosion, a high-frequency pressure sensor collected pressure change data, and a high-speed camera recorded the flame development process. The results indicated that the maximum explosion overpressure (ΔP_max) decreased with time, and the arrival time of the maximum explosion overpressure (ΔP_max) delayed. The appearance time of the “tulip” shaped flame delayed, and the flame propagation speed decreased. The ultrafine water mist and deposition can effectively inhibit the methane explosion. The explosion suppression effect of the second step spraying water mist was better. The improvement of the explosion suppression effect of the ultrafine water mist containing methane-oxidizing bacteria was attributed to the degradation effect of the methane-oxidizing bacteria. Under long-term degradation, methane-oxidizing bacteria in water mist play a role in inhibiting methane explosion.     

A numerical modelling of an influence of CH4, N2, CO2 and steam on a laminar burning velocity of hydrogen in air

The influence of additives of various chemical natures (CH₄, N₂, CO₂, and steam) at a laminar burning velocity S_u of hydrogen in air has been studied by numerical modelling of a flat flame propagation in a gaseous mixture. It was found that the additives of methane to hydrogen–air mixtures cause as a rule monotonic reduction in the S_u value with the exception of very lean mixtures (fuel equivalence ratio ? = 0.4), for which a dependence of the laminar burning velocity on the additive's concentration has a maximum. In the case of the chemically inert additives (N₂, CO₂, H₂O) the laminar burning velocity of rich near-limit hydrogen–air flames drops monotonically with an increase in the additive's content, but no more than 1.5 times, and the adiabatic flame temperature changes slowly in this case. In the case of methane as the additive, the laminar burning velocity is diminished approximately 5 times with an increase in the adiabatic flame temperature from 1200 to 2100 K. Deviations from the known empirical rule of the approximate constancy of the laminar burning velocity for near-limit flames are shown.     

Effects of premixed methane concentration on distribution of flame region and hazard effects in a tube and a tunnel gas explosion

Study of flame distribution laws and the hazard effects in a tunnel gas explosion accident is of great importance for safety issue. However, it has not yet been fully explored. The object of present work is mainly to study the effects of premixed gas concentration on the distribution law of the flame region and the hazard effects involving methane-air explosion in a tube and a tunnel based on experimental and numerical results. The experiments were conducted in a tube with one end closed and the other open. The tube was partially filled with premixed methane-air mixture with six different premixed methane concentrations. Major simulation works were performed in a full-scale tunnel with a length of 1000 m. The first 56 m of the tunnel were occupied by methane–air mixture. Results show that the flame region is always longer than the original gas region in any case. Concentration has significant effects on the flame region distribution and the explosion behaviors. In the tube, peak overpressures and maximum rates of overpressure rise (dp/dt)_max for mixtures with lower and higher concentrations are great lower than that for mixtures close to stoichiometric concentration. Due to the gas diffusion effect, not the stoichiometric mixture but the mixture with a slightly higher concentration of 11% gets the highest peak overpressure and the shock wave speed along the tube. In the full-scale tunnel, for fuel lean and stoichiometric mixture, the maximum peak combustion rates is achieved before arriving at the boundary of the original methane accumulation region, while for fuel rich mixture, the maximum value appears beyond the region. It is also found that the flame region for the case of stoichiometric mixture is the shortest as 72 m since the higher explosion intensity shortens the gas diffusion time. The case for concentration of 13% can reach up to a longest value of 128 m for longer diffusion time and the abundant fuel. The “serious injury and death” zone caused by shock wave may reach up to 3–8 times of the length of the original methane occupied region, which is the widest damage region.     

Flame propagation in lycopodium/air mixtures below atmospheric pressure

Industrial processes are often operated at conditions deviating from atmospheric conditions. Safety relevant parameters normally used for hazard evaluation and classification of combustible dusts are only valid within a very narrow range of pressure, temperature and gas composition. The development of dust explosions and flame propagation under reduced pressure conditions is poorly investigated. Standard laboratory equipment like the 20 l Siwek chamber does not allow investigations at very low pressures. Therefore an experimental device was developed for the investigations on flame propagation and ignition under reduced pressure conditions. Flame propagation was analysed by a video analysis system the actual flame speed was measured by optical sensors. Experiments were carried out with lycopodium at dust concentrations of 100 g/m³, 200 g/m³ and 300 g/m³. It was found that both flame shapes and flame speeds were quite different from those obtained at atmospheric pressure. Effects like buoyancy of hot gases during ignition and flame propagation are less strong than at atmospheric conditions. For the investigated dust concentrations the flame reaches speeds that are nearly an order of a magnitude higher than at ambient conditions.