The efficiency of two standardized procedures for extracting mutagenic chemicals from soils

A major technical limitation to monitoring the fate of mutagenic compounds in soil is the lack of an established extraction procedure. This study was conducted to evaluate the efficiency of the blender extraction procedure for extracting benzo(a)pyrene (BAP) or 2-nitrofluorene (2NF) from a Weswood silt loam or a Bastrop clay loam soil. Extracted residues were evaluated using the Salmonella/microsome mutagenicity assay and high performance liquid chromatography (HPLC) to quantify recovery of the two chemicals from soil. In addition, a limited study using only the mutagenicity assay was conducted to compare the efficiency of the Blender and Soxhlet extraction procedures for recovering organic mutagens from both soils amended with a wood preserving bottom sediment waste.Extracted residues were dissolved in dimethylsulfoxide to concentrations that could be detected in the bioassay. Over all treatment levels and for both soils, the extraction efficiency of the blender procedure for BAP was greater than 80% for 12 of 16 treatments as measured using both bioassay and HPLC analysis; while, for 2NF the extraction efficiency was greater than 90% for all 15 treatments as measured by HPLC, and greater than 80% for twelve of 15 treatments as measured by bioassay. These results indicate that blender extraction provided efficient recovery of the pure compounds tested. When the efficiency of the blender and Soxhlet procedure for extracting the wood-preserving bottom sediment and waste amended soil were compared, significantly greater levels of mutagenic activity were detected in the fractions extracted using the blender extraction than were detected using the Soxhlet extraction.     

Adaptation and validation of QuEChERS method for the analysis of trifluralin in wind-eroded soil

This study was carried out to develop and validate a reliable analytical procedure for trifluralin analysis in wind-eroded sediments. Soil sediments trapped in BEST sediment traps were subjected to QuEChERS extraction method, incorporating a simple simultaneous cleanup step, followed by trifluralin analysis with GC-ECD. Results revealed that QuEChERS method offered a potential alternative technique for pesticide extraction from soil samples. The validity of analytical method was performed by the method-performance criteria such as, recovery, LOD, LOQ repeatability, precision, and all found to be within the required limits. It was also observed in this study that herbicide concentrations in the wind-eroded sediment did not vary with the time and trap height. Trifluralin concentrations of surface soil after four erosion events were higher (626.05 μg/kg) than wind-eroded soil (450.08 μg/kg).     

Optimisation of pressurised liquid extraction for elimination of sulphur interferences during determination of organotin compounds in sulphur-rich sediments by gas chromatography with flame photometric detection

A simple method for species-selective analysis of organotin compounds (OTCs) (butyl and phenyl) in sediments was developed. The sample preparation procedure was specifically optimised for sulphur-rich sediments to eliminate interferences from elemental sulphur and organosulphur compounds. Tin species were extracted from sediment samples using pressurised liquid extraction technique (PLE), ethylated - with simultaneous extraction to isooctane - in aqueous phase with sodium tetraethylborate (NaBEt(4)) and separated/detected by gas chromatography with flame photometric detection (GC-FPD). PLE operational variables (extraction temperature and pressure, solvent composition and number of static extraction steps) and extract handling routine were fine-tuned to minimise the amount of extracted interferents while keeping OTCs recovery at an acceptable level. Best results were obtained after extraction of sediment samples with methanol/water (75% v/v methanol) solution of acetic acid/sodium acetate with tropolone addition (0.6 g l(-1)). Derivatisation of low temperature, high-pressure (50 degrees C, 13.8 MPa) extracts gives isooctane extracts which are clean enough to be directly analysed by GC-FPD without any further cleanup. Interferences from elemental sulphur were completely eliminated while concentrations of other interferents were reduced to the level not impairing quantitation of OTCs under the study. No negative effects in terms of chromatographic column deterioration were observed after repeated injections of such extracts. Two certified reference materials, BCR646 and PACS-2, were analysed to assess performance of the method. Recoveries of all OTCs under the study, except MBT, were in the range of 91-114%. MBT extraction efficiency was low (34-47%) therefore the method is unsuitable for precise determinations of this compound.     

Persistent organic pollutants in water and surface sediments of Taihu Lake,China and risk assessment

Organic pollutants, especially persistent organic pollutants were examined in the water and surface sediments of Taihu Lake, China. Both 12 water and 12 sediment samples were collected over the lake. C-18 solid-phase extraction technique was applied to extract organic pollutants in collected water samples. Soxhlet extraction procedure was used to extract organic pollutants in sediment samples. The analysis was performed by GC-MS controlled by a Hewlett Packard chemstation. Two hundred and seventy-three kinds of organic chemicals in water were examined, 200 more than that detected in 1985; 188 kinds of chemicals in sediments were detected as well. Among them 21 kinds of chemicals belong to priority pollutants as well as 17 kinds to be the endocrine disruptors. The concentrations of the pollutants were more than 2 times higher than that in 1985. The possible source and relation to anthropogenic activity were discussed.     

Distribution and fractionation of heavy metals in the Tisa (Tisza) River sediments

Introduction In this work, sediments of the River Tisa (Tisza) are studied to assess their environmental pollution levels for some major heavy metals, as well as to predict the investigated elements’ mobility on the basis of their association type with the substrate. The Tisa River catchments area is a subbasin of the River Danube. Part of this river, 166 km long, belongs to the Serbian province of Vojvodina, before it flows into the Danube. It has been chosen for our investigation, because it has been exposed to intense pollution in the last decades. Materials and Methods The river sediment samples were collected at 32 locations. The proportions of sand, silt and clay fractions were determined. The sequential extraction procedure following a modified Tessier method was applied for speciation of the metal forms in the collected samples. The metal concentrations of Zn, Cd, Pb, Ni, Cu, Cr, Fe and Mn in extracts were determined by atomic absorption spectroscopy. Results and Discussion Granulometric analysis showed that some 50% of the Tisa River sediments were silt and clay, while the rest was sand with quartz, as the main constituent. The average metal content of the surface river sediment samples for every fraction of sequential extraction was presented and discussed in relation to pH, Eh and metal fractionation. The average metal content from the Tisa River sediments, obtained as an average of the metal’s concentration released in all five sequential extraction fractions was compared with: average metal contents of the Tisa River sediments in Hungary, metal content in soils formed on the Tisa River alluvium of Vojvodina, average metal content in soils of Vojvodina, and average metal content in soils of Hungary. An assessment of metal pollution levels in Tisa River sediments was made by comparing mean values for obtained results for the Tisa River sediments with the freshwater sediment’s Quality Guidelines as published by US EPA, Environment Canada and soil standards for Serbia. Conclusion According to US EPA and Canadian Quality Guidelines for freshwater sediments, the concentration of heavy metals in Tisa sediments were: (a) much higher than defined concentrations below which harmful effects on river biota are unlikely to be observed, (b) below defined concentrations above which harmful effects on river biota are likely to be observed. The concentration levels of Pb, Ni, Cu and Cr in Tisa River sediments are safe when compared with Serbian MAQ (Maximum Allowed Quantity) standards for soils, but they are unsafe in the case of Zn and Cd. Recommendations and Outlook The quality of sediments in the Tisa River was on the border line between potentially polluted and polluted. This line could very easily be exceeded since the quality of sediments in the Tisa River in Hungary was already worse than in Serbia. These results indicated the need for further monitoring of heavy metals in that locality.     

Extraction of organic contaminants from marine sediments and tissues using microwave energy.

In this study, we compared microwave solvent extraction (MSE) to conventional methods for extracting organic contaminants from marine sediments and tissues with high and varying moisture content. The organic contaminants measured were polychlorinated biphenyl (PCB) congeners, chlorinated pesticides, and polycyclic aromatic hydrocarbons (PAHs). Initial experiments were conducted on dry standard reference materials (SRMs) and field collected marine sediments. Moisture content in samples greatly influenced the recovery of the analytes of interest. When wet sediments were included in a sample batch, low recoveries were often encountered in other samples in the batch, including the dry SRM. Experiments were conducted to test the effect of standardizing the moisture content in all samples in a batch prior to extraction. SRM1941a (marine sediment). SRM1974a (mussel tissue), as well as QA96SED6 (marine sediment), and QA96TIS7 (marine tissue), both from 1996 NIST Intercalibration Exercise were extracted using microwave and conventional methods. Moisture levels were adjusted in SRMs to match those of marine sediment and tissue samples before microwave extraction. The results demonstrated that it is crucial to standardize the moisture content in all samples, including dry reference material to ensure good recovery of organic contaminants. MSE yielded equivalent or superior recoveries compared to conventional methods for the majority of the compounds evaluated. The advantages of MSE over conventional methods are reduced solvent usage, higher sample throughput and the elimination of halogenated solvent usage.     

Release of vanadium from oxidized sediments: insights from different extraction and leaching procedures

Although the attention for vanadium (V) as a potentially harmful element is growing and some countries adopted threshold values for V in soils, sediments, groundwater, or surface water, V is generally of little importance in environmental legislation and the knowledge about the behavior of V in the environment is still limited. In the present study, the release of V from oxidized sediments, sediment-derived soils, and certified reference materials was investigated by means of several types of leaching tests and extractions that are frequently used for soil and sediment characterization. The pH_stat leaching tests and single and sequential extractions applied in this study show that V generally displays a very limited actual and potential mobility in sediment. “Mobile” V concentrations, as estimated by the amount of V released by a single extraction with CaCl₂ 0.01 mol L^?1, were low, even in the most contaminated sediment samples. Only under strongly acidifying conditions (pH 2), such as in the case of ingestion of soil or sediment or in accidental spills, a substantial release of V can be expected.     

Comparative study of extraction methods for the determination of PAHs from contaminated soils and sediments

The following four methods were compared on the extraction efficiency of 16 EPA (US Environmental Protection Agency) polycyclic aromatic hydrocarbons (PAHs): German method of the Verband Deutscher Landwirtschaftlicher Untersuchungs und Forschungsanstalten (VDLUFA), two methods of the International Organization for Standardization using shaking (ISO A) and Soxhlet extraction (ISO B) and an ultrasonic method. Recovery rates of 16 PAHs were determined in two soils. Extraction efficiency was evaluated in five soils and three sediments. Effect of drying soils and sediments on extraction efficiency was tested using the VDLUFA and the ultrasonic methods. Our study shows that the number of aromatic rings, rather than extraction procedures, significantly influenced recovery rates of individual PAHs. No significant differences in extraction efficiency of the four methods were observed for less polluted samples. For highly polluted soils, extraction efficiency decreased in the following order: VDLUFA method > ISO A > ultrasonic method > ISO B. Influence of soil moisture on extraction efficiency depended to some extent on both solvent used and content of PAHs in samples. A mixture of dichloromethane/acetone (5:1) is recommended for PAH extraction from moist samples when the ultrasonic method is used.     

Evaluation of an extraction method for a mixture of endocrine disrupters in sediment using chemical and in vitro biological analyses

Aquatic sediments are contaminated by a wide diversity of organic pollutants such as endocrine-disrupting chemicals (EDCs) which encompass a broad range of chemical classes having natural and anthropogenic origins. The use of in vitro bioassays is now widely accepted as an alternative method for their detection in complex samples. However, based on the diversity of EDC chemical properties, their common extraction is difficult and comprehensive validation of extraction methods for a bioanalysis purpose is still weakly documented. In this study, we compared the performance of several organic solvents, i.e., acetone, methanol, dichloromethane, heptane, dichloromethane/acetone (50:50, v/v), dichloromethane/methanol (50:50, v/v), heptane/acetone (50:50, v/v), and heptane/methanol (50:50, v/v), to extract a diversity of active chemicals from a spiked sediment matrix using pressurized liquid extraction. For this purpose, we defined a mixture of 12 EDCs with a wide range of polarity (2?<?log Kow?<?8) (i.e., estrone, 17β-estradiol, bisphenol A, o,p′DDT, 4-tert-octylphenol, fenofibrate, triphenyl phosphate, clotrimazole, PCB-126, 2,3,7,8 TCDD, benzo[k]fluoranthene, and dibenzo[a,h]anthracene). Working concentrations of each individual compound in the mixture were determined as equipotent concentrations on the basis of the concentration-addition (CA) model applied to in vitro estrogenic, dioxin-like, and pregnane X receptor (PXR)-like activities. Extraction efficiencies based on both chemical and biological analyses were assessed in triplicate in artificial blank sediment spiked with this mixture and in natural sediment contaminated by native EDCs. In both spiked and natural sediment, MeOH/DCM yields the best recovery while heptane was the least efficient solvent. Our study provided the validation of a sediment extraction methodology for EDC bioanalysis purposes, which can be used for comprehensive environmental contamination characterization.     

Optimization of analytical methods to improve detection of erythromycin from water and sediment

Analytical methods to improve the detection of erythromycin in water and sediment were developed to optimize for erythromycin's recovery of extractable and bound residues from the aquatic environment. The objective of this study was to determine optimal recovery of erythromycin from water and sediment to improve its detection in environmental samples through solid-phase extraction (SPE) and sediment-extraction methods. SPE methods examined included previously reported methods for macrolide and sulfonamide antibiotics with erythromycin recoveries ranging from 75.5 % to 94.7 %. Extraction of erythromycin was performed from sand employing various solvents and buffers to determine the best method for extraction from two sandy loam pond sediments. Various extraction times were also examined, and all extraction procedures were performed in duplicate. The greatest recovery of ¹⁴C-erythromycin in the Iowa sediment was 84 % using 0.3 M ammonium acetate at pH 4.2: acetonitrile (15:85, v/v) solution. The Oklahoma sediment yielded the greatest recovery of ¹⁴C-erythromycin at 86.7 % with 0.3 M ammonium acetate at pH 7: acetonitrile (30:70, v/v) with a 60-minute shake time. The present results demonstrate improved extraction methods for enhancing the accuracy of erythromycin detection from environmental samples.     

Quantification of activated carbon contents in soils and sediments using chemothermal and wet oxidation methods

Activated carbon (AC) strongly sorbs organic pollutants and can be used for remediation of soils and sediments. A method for AC quantification is essential to monitor AC (re)distribution. Since AC is black carbon (BC), two methods for BC quantification were tested for AC mixed in different soils and sediments: i) chemothermal oxidation (CTO) at a range of temperatures and ii) wet-chemical oxidation with a potassium dichromate/sulfuric acid solution. For three soils, the amount of AC was accurately determined by CTO at 375 °C. For two sediments, however, much of the AC disappeared during combustion at 375 °C, which could probably be explained by catalytic effects by sediment constituents. CTO at lower temperatures (325-350 °C) was a feasible alternative for one of the sediments. Wet oxidation effectively functioned for AC quantification in sediments, with almost complete AC recovery (81-92%) and low remaining amounts of native organic carbon (5-16%).     

Dissolved organic matter in pore water of freshwater sediments: effects of separation procedure on quantity, quality and functionality

Pore water was separated either with or without water extraction prior to centrifugation (7600 or 20 000 × g) in order to investigate the effects of separation procedure on the amount and properties of dissolved organic matter (DOM i.e. the material passing through a 0.45-μm filter) in three freshwater sediments. On the basis of solubility in alkaline, organic matter was concluded to compose of humic substances in two (S1 and S3) and of humin (S2) in one of the sediments. DOM in the samples was quantified by total organic carbon measurement. Specific UV-absorption (SUVA) and high performance size exclusion chromatography (HPSEC) analyses were used to characterize DOM. Sorption of pyrene was used as a measure for functionality of DOM. Both water extraction and centrifugation speed were shown to affect the properties of DOM; however, the effects were sediment dependent. Water extraction increased the amount of DOM separated from the two sediments that had humic character (S1 and S3). In most cases water extraction increased SUVA and shifted the molecular size distribution of DOM towards larger sizes. The separation procedure had also an effect on the functionality of DOM. In water extracted samples of S2 and S3 the sorption of pyrene was higher than in the corresponding samples separated without water extraction, whereas in S1 similar effect was not found. Generally, centrifugation speed had smaller effects on the properties of DOM than water extraction. The fact that the effects of separation procedure on DOM depend on the sediment characteristics complicates the comparison between samples and evaluation of functionality in field conditions.     

Optimization of analytical methods to improve detection of erythromycin from water and sediment

Analytical methods to improve the detection of erythromycin in water and sediment were developed to optimize for erythromycin's recovery of extractable and bound residues from the aquatic environment. The objective of this study was to determine optimal recovery of erythromycin from water and sediment to improve its detection in environmental samples through solid-phase extraction (SPE) and sediment-extraction methods. SPE methods examined included previously reported methods for macrolide and sulfonamide antibiotics with erythromycin recoveries ranging from 75.5 % to 94.7 %. Extraction of erythromycin was performed from sand employing various solvents and buffers to determine the best method for extraction from two sandy loam pond sediments. Various extraction times were also examined, and all extraction procedures were performed in duplicate. The greatest recovery of (14)C-erythromycin in the Iowa sediment was 84 % using 0.3 M ammonium acetate at pH 4.2: acetonitrile (15:85, v/v) solution. The Oklahoma sediment yielded the greatest recovery of (14)C-erythromycin at 86.7 % with 0.3 M ammonium acetate at pH 7: acetonitrile (30:70, v/v) with a 60-minute shake time. The present results demonstrate improved extraction methods for enhancing the accuracy of erythromycin detection from environmental samples.     

Hydroxypropyl-β-cyclodextrin extractability and bioavailability of phenanthrene in humin and humic acid fractions from different soils and sediments

Organic matter (OM) plays a vital role in controlling polycyclic aromatic hydrocarbon (PAH) bioavailability in soils and sediments. In this study, both a hydroxypropyl-β-cyclodextrin (HPCD) extraction test and a biodegradation test were performed to evaluate the bioavailability of phenanthrene in seven different bulk soil/sediment samples and two OM components (humin fractions and humic acid (HA) fractions) separated from these soils/sediments. Results showed that both the extent of HPCD-extractable phenanthrene and the extent of biodegradable phenanthrene in humin fraction were lower than those in the respective HA fraction and source soil/sediment, demonstrating the limited bioavailability of phenanthrene in the humin fraction. For the source soils/sediments and the humin fractions, significant inverse relationships were observed between the sorption capacities for phenanthrene and the amounts of HPCD-extractable or biodegradable phenanthrene (p?<?0.05), suggesting the importance of the sorption capacity in affecting desorption and biodegradation of phenanthrene. Strong linear relationships were observed between the amount of HPCD-extractable phenanthrene and the amount degraded in both the bulk soils/sediments and the humin fractions, with both slopes close to 1. On the other hand, in the case of phenanthrene contained in HA, a poor relationship was observed between the amount of phenanthrene extracted by HPCD and the amount degraded, with the former being much less than the latter. The results revealed the importance of humin fraction in affecting the bioavailability of phenanthrene in the bulk soils/sediments, which would deepen our understanding of the organic matter fractions in affecting desorption and biodegradation of organic pollutants and provide theoretical support for remediation and risk assessment of contaminated soils and sediments.     

Concentration and fate of persistent organochlorine pesticides in estuarine sediments using headspace solid-phase microextraction

The concentration and fate of persistent organochlorine pesticides (OCPs) in estuarine surface sediments in Erh-jen and Lan-yang rivers, Taiwan were investigated using headspace solid-phase microextraction (HSSPME) method to evaluate the possible pollution potential and guideline for OCP concentrations in Taiwan. The HSSPME method exhibits a good analytical performance with low detection limits for OCP determination in sediment. In addition, results obtained using the developed HSSPME method were in good agreement with those obtained using Soxhlet extraction in a certified sample. The developed analytical method was further applied to the determination of concentrations of OCP residues in surface sediments from the estuaries of the selected rivers in Taiwan. A total of 20 surface sediments from each river was collected from 10 sampling stations. The total OCP concentrations in sediments from Erh-jen River ranged from 0.17 to 5.04 ng/g-dw with the mean values of 0.25–1.24 ng/g-dw for HCHs, 0.10–0.89 ng/g-dw for cyclodienes and 0.16–0.64 ng/g-dw for DDTs. The concentrations of OCPs in sediments from Lan-yang River were in the range 0.37–0.9 ng/g-dw with an average of lower than 0.5 ng/g-dw. HCHs and DDTs were abundant in the estuarine sediments from the selected rivers. Results obtained in this study show that the origin of OCPs in the surface sediments from Erh-jen River is a combination of erosion of the weathered soils and long-range atmospheric transport, while the OCP concentrations found in Lan-yang River could be regarded as the background levels of OCPs in Taiwan.     

Slow desorption of PCBs and chlorobenzenes from soils and sediments: relations with sorbent and sorbate characteristics

The kinetics of slow desorption were studied for four soils and four sediments with widely varying characteristics [organic carbon (OC) content 0.5-50%, organic matter (OM) aromatic content (7-37%)] for three chlorobenzenes and five polychlorinated biphenyls (PCBs). Slowly and very slowly desorbing fractions ranged from 1 to 50% (slow) and 3 to 40% (very slow) of the total amount sorbed, and were observed for all compounds and all soils and sediments. In spite of the wide variations in sorbate K(OW) (factor 1000) and sorbent characteristics, the rate constants of slow (k(slow), around 10(-3) h(-1)) and very slow (k(very slow), 10(-5)-10(-4) h(-1)) desorption appeared to be rather constant among the sorbates and sorbents (both within a factor of 5). There was a good correlation (r(2) above 0.9) between the distribution over the slow, very slow and rapid sediment fractions and log K(OC), indicating that sorbate hydrophobicity may be important for this distribution. No correlation could be found between sorbent characteristics [OC, N, and O in the organic matter, polarity index C/(N+O), OC aromaticity as determined by CP-MAS (13)C-NMR] and slow desorption parameters (slowly/very slowly desorbing fractions+corresponding rate constants). The absence of (1) a correlation between k(slow) and k(very slow), respectively, and OC content, and (2) the narrow range of k(slow) and k(very slow) values, indicates that intra-OM diffusion is not the mechanism of slow or very slow desorption, because on the basis of this mechanism it would be expected that increasing OC content would lead to longer diffusion pathlengths and, consequently, to smaller rate constants. In addition, it was tested whether differential scanning calorimetry would reveal a glass transition in the soils/sediments. In spite of the sensitivity of the equipment used (changes in heat flow in the micro-Watt range were measurable), a glass transition was not observed. This means that activation enthalpies of slow desorption can be calculated from desorption measurements at various temperatures. In the present study these values ranged from 60 to 100 kJ/mol among the various soils and sediments studied.     

Analysis of dioxins and furans in environmental samples by GC-ion-trap MS/MS

The work aims to characterise PCDDs/Fs in environmental matrices by high resolution gas chromatography coupled to low resolution quadrupole ion-trap mass spectrometry (GC-QITMS/MS). In particular, the study was mainly focused in different environmental samples such as sewage sludge, soils, and sediments and in combustion residues as fly ashes. Previous experiences have already detected and quantified PCDDs/PCDFs in all matrices studied. Moreover, isomer-specific analysis of 2,3,7,8-PCDDs/Fs compounds corroborated good correlation between GC-QITMS/MS and a well-established technique such as high resolution mass spectrometry (HRMS). Finally, QC measures included the participation in intercalibration exercises. Successful results were achieved using GC-QITMS/MS in the analysis of fly ashes, soils and sediment materials. In general, GC-QITMS/MS constitutes an interesting alternative for routine analysis of dioxins in such as matrices.     

The leachability, bioaccessibility, and speciation of Cu in the sediment of channel catfish ponds

There have been growing concerns about the environmental impact of Cu applied in the catfish pond aquaculture. In this paper, sediments taken from three commercial catfish ponds were studied for content, leachability, bioaccessibility, and speciation of sediment-bound Cu. Results showed that the Cu was concentrated in the top 10 cm of the sediments and the peak Cu concentrations ranged from the background level to about 200 mg/kg. Toxicity characteristic leaching procedure showed only 1-8% of sediment Cu was leachable while bioaccessible Cu, evaluated by physiological based extraction test, accounted for up to 40-85% of total Cu. Due to the high redox potential in the surface sediments, acid-volatile sulfide was not a significant binding phase. The sequential extraction results showed that the residual phase (forms in lattices of primary and secondary minerals) was the major Cu fraction in the first two pond sediments but carbonate-bound, Fe/Mn oxide-bound and organically bound Cu, as well as the residual fraction, seemed equally important in the third pond.     

Spatial distribution of mercury in the sediments and riparian environment of the River Yare, Norfolk, UK

Concentrations of total mercury (T-Hg) were determined in sediments and riparian (bankside) soils from the River Yare, Norfolk, UK to assess the current extent of contamination arising from a historical point source discharge. The results demonstrate that the spatial distribution pattern in surficial sediments and soils follows that of a distinct pollution plume with an initial increase 2-3 km downstream from the point source discharge at Whitlingham Sewage Treatment Works (STW) outfall. Average T-Hg concentrations in the surficial sediments ranged from 0.1 to 8.13 mg kg(-1); bankside soil concentrations ranged from 0.1 to 2.63 mg kg(-1). There has been a decline in downstream background sediment concentrations of Hg over time. This is likely to be the result of burial by fresh relatively uncontaminated sediments and possibly in the lower reach as a consequence of the influence of the freshwater-saline interface occurring near Cantley. Channel morphology was also shown to be an important factor in determining the large variations of Hg concentrations between sample points within transects. The predominant source of Hg to the soils appears to be due to dredging and the deposition of sediments during flooding.     

Development of a simple selective SFE method for the determination of desorption behaviour of PCBs in two Swedish sediments

A simple selective supercritical fluid extraction (SFE) method was developed for the determination of desorption behaviour of PCBs in sediments. This method was applied to determine the distribution of individual PCB congeners among sites of differing bonding strengths in two Swedish sediments (Lake J?rnsj?n and Baltic bay Orserumsviken). Four different PCB fractions were distinguished in each sediment by applying consecutively harsher supercritical fluid extraction conditions on the same sample. Even though the two sediments had completely different textures, they showed very similar extraction behaviour. It was shown that, in both sediments, a major part of the PCBs (58% and 65%, respectively) were located at "fast sites", from which they were extractable already with the mildest extraction conditions (60 min, 40 degrees C and 120 bar). Only a small fraction of the PCBs were so tightly bound to the sediments (located at "slow sites"), that they could be extracted only under the harshest conditions (60 min, 150 degrees C and 400 bar). Information of this kind should be of great value for the determination of bioavailability of pollutants in sediments and soils, and it is the author's belief that this technique has the potential to develop into a powerful tool in environmental risk assessment.