膜生物反应器次临界通量运行的膜污染特性研究

膜生物反应器（MBR）是将膜分离与生物反应相结合的污水处理新工艺,近年来已引起广泛的关注,但不可避免的膜污染限制其更广泛的应用。临界通量在膜污染控制中是个非常重要的概念。本试验研究平板膜生物反应器在次临界通量运行下的膜污染状况,并结合膜污染模型进一步表征膜表面的污染特性。试验结果表明。该平板膜生物反应器在次临界通量运行的情况下,膜污染可分为膜污染缓慢发展阶段（第Ⅰ阶段）和膜污染迅速发展阶段（第Ⅱ阶段）,可分别用膜孔堵塞模型和泥饼阻力模型表征膜阻力与时间的变化关系。同时,对运行后的膜阻力分布进行分析,表明泥饼阻力和孔道吸附堵塞阻力是膜污染的主要组成部分,分别占到总阻力的73％和24％,而膜本身阻力仅占3％。     

MBR在污水处理中的应用

膜生物反应器是生物降解与膜分离相互影响、共同作用的过程。综述了膜生物反应器在污水处理中的应用及发展方向。     

气升循环分体式膜生物反应器污水处理与回用技术

介绍了一种新型膜生物反应器——气升循环分体式膜生物反应器污水处理和再生回用技术。该技术膜单元和生物单元分置，生物单元和膜单元间的水力循环利用气升动力，无需循环水泵，系统具有维护方便、运行能耗低和建设投资省等特点。采用该技术处理生活污水和厕所污水，处理水质可达到建设部颁布的《生活杂用水水质标准》(CJ25．1-89)。给出了该技术处理生活污水和厕所污水的工程建设投资指标、水处理成本和水处理能耗指标，处理能耗0．6-0．8kWh／m^3。该新型膜生物反应器污水再生回用技术具有良好的市场应用前景，技术经济可行。     

中空纤维膜生物反应器处理造纸废水

膜生物反应器是将膜分离技术与生物处理工艺相结合而开发的新型系统,是近年来新发展起来的高效废水处理技术。本实验采用了中空纤维膜组件和活性污泥反应器组成的分置式膜生物反应器,研究其在造纸废水处理中的特性影响因素。     

膜—生物反应器在废水处理中的应用

膜分离技术与生物反应器的组合工艺已成为废水处理中的螈使用使废消息我加紧凑,且出水水质良好。膜－生物反应器已被成功地应用于城市污水及工业废水等废水处理中,阐述了膜－生物反应器的原理、特点、研究现状。     

气升循环分体式膜生物反应器污水处理与回用技术

介绍了一种新型膜生物反应器———气升循环分体式膜生物反应器污水处理和再生回用技术。该技术膜单元和生物单元分置 ,生物单元和膜单元间的水力循环利用气升动力 ,无需循环水泵 ,系统具有维护方便、运行能耗低和建设投资省等特点。采用该技术处理生活污水和厕所污水 ,处理水质可达到建设部颁布的《生活杂用水水质标准》(CJ2 5 1 89)。给出了该技术处理生活污水和厕所污水的工程建设投资指标、水处理成本和水处理能耗指标 ,处理能耗 0 6～ 0 8kWh/m3 。该新型膜生物反应器污水再生回用技术具有良好的市场应用前景 ,技术经济可行。     

微米级负载型TiO_2催化剂在光催化-膜分离反应器中的应用

基于光催化-膜分离三相流化床反应器的结构特点及膜分离特性,以微米级MCM-41分子筛为载体,采用原位生成法制备微米级负载型TiO2催化剂。针对微米级负载型TiO2催化剂在光催化-膜分离反应器中的分布特性、悬浮特性、分离特性及膜污染特性进行研究。结果表明,曝气量一定的情况下,微米级负载型TiO2催化剂在光催化-膜分离反应器中具有良好的悬浮特性,且优于纳米TiO2。随着催化剂投加量的增加,悬浮浓度也随之增加。光催化反应器底部曝气0.3m3/h、催化剂投加量为1 g/L时为宜。膜分离器中催化剂悬浮浓度明显低于光催化反应器;该微米级催化剂与纳米TiO2相比具有不粘附、不堵塞膜孔等优良特性,能够有效降低膜污染,延长分离膜使用寿命。膜底曝气为0.1 m3/h时,反应器连续运行5 h(未加反冲洗)后,微米级负载型TiO2催化剂和纳米TiO2对膜组件的污染程度分别为膜通量衰减率4.3%和37.4%。反应器连续运行72 h,膜组件依然具有很好的分离特性。     

膜生物反应器生物降解与膜分离共作用特性研究

膜生物反应器实质是生物降解与膜分离相互影响,共同作用的过程,污泥浓度与通量之间存在一定的相关关系,膜分离对生和性能尤其是细菌活性有着重要的影响,而生物反应器内细菌胞外聚合物,溶解性有机物及微细胶体可能成为形成凝胶层导致通量下降的主要因素。     

SMBR处理含油废水出水COD数学模型

根据微生物生长动力学特征以及膜分离特征,建立恒通量下运行的一体式膜生物反应器系统出水COD数学模型,提出膜生物反应器处理效率的数学模型。以实验及模型为基础,分别对进水COD浓度控制在300、400、500 mg/L附近时经过反应器后COD的去除效率进行了比较。通过公式计算的数据和实验数据分析可得:COD去除率的公式计算值与实验结果比较吻合,相对偏差仅为0.0223,为膜系统有机物的去除效果估算提供了基础,可为该类工艺的参数选择与优化提供参考。     

普通活性污泥膜生物反应器处理洗车废水的应用研究

膜生物反应器是近年来发展起来的一种新型高效水处理设备。它将分离工程中的膜技术应用于好氧活性污泥处理系统，由膜组件取代传统生化处理技术中的二次沉淀池和砂滤池，由膜分离技术代替传统方法中的重力式沉淀泥水分离技术方式，具有简洁、高效等优点。采用普通活性污泥膜生物反应器工艺对天津某一洗车点洗车废水进行处理，并将处理出水回用于洗车。     

A modeling study of fouling development in membrane bioreactors for wastewater treatment.

Membrane fouling is a primary concern in membrane bioreactors (MBRs) in wastewater treatment because it strongly affects both system stability and economic feasibility. A mathematical model was developed in this study for membrane fouling in submerged MBR systems for wastewater treatment, in which both reversible and irreversible fouling were quantified. While mixed liquor suspended solids are the major components of the reversible fouling layer, dissolved organic matter is thought to be the key foulant, in particular, responsible for the long-term irreversible fouling of the filtration unit. The model was calibrated (parameter identification) with a set of operational data from a pilot MBR and then verified with other independent operational data from the MBR. The good agreement between theoretical predictions and operational data demonstrates that the outlined modeling concept can be successfully applied to describe membrane fouling in submerged MBR systems.     

Comparison of sludge characteristics and PCR-DGGE based microbial diversity of nanofiltration and microfiltration membrane bioreactors

The objective of this study was to compare the sludge characteristics and microbial community diversity between the submerged nanofiltration membrane bioreactor (NF MBR) and microfiltration membrane bioreactor (MF MBR) treating the same municipal wastewater. The influence of a higher concentration of organic matter and salt was investigated. The results of water qualities showed that the dissolved organic carbon (DOC), total phosphorus (T-P) and salt concentrations of the supernatant in the NF MBR were three, four and two times as high as those in the MF MBR, respectively. The specific oxygen uptake rate of the NF MBR (2.9+/-0.4 mg O(2)g(-1)MLSSh(-1)) was lower than that of the MF MBR (4.3+/-1.1 mg O(2)g(-1)MLSS h(-1)). Result of extractable extracellular polymeric substances showed that the NF MBR sludge had more protein and less polysaccharide compared to the MF MBR sludge, whereas specific amount of total organic carbon were the same in both MBRs. The median floc diameters of the NF MBR and the MF MBR were 72+/-12 microm and 59+/-12 microm, respectively, which could be attributable to the different polysaccharide concentrations between both MBR mixed liquor. A higher concentration of materials (DOC, T-P and salt) in the bioreactor, determined by the high rejection rate of the NF membrane, did not significantly affect the microbial diversity under similar operation conditions.     

Performance investigation of membrane bioreactor systems during municipal wastewater reclamation.

Four commercially available membrane bioreactor (MBR) systems were operated at the pilot scale, to investigate performance during the reclamation of municipal wastewater. The MBR performance was evaluated under a variety of operating conditions, including two types of feed wastewater (raw and advanced primary effluent), hydraulic retention times (HRTs) ranging from 2 to 6 hours, and permeate fluxes between 20 and 41 lmh. Test results showed that MBR systems were capable of operating on advanced primary effluent, despite the possible presence of coagulant and/or polymer residual, with minimal membrane fouling. Membrane performance data generated during this study was also used to quantify the relationship between permeate flux and membrane fouling. Cleaning intervals at various flux conditions were estimated as follows: 69 days at 20 lmh, 58 days at 25 lmh, and 30 days for operation between 31 and 41 lmh. It was also demonstrated that the MBR process could be optimized to operate with minimal fouling under high hydraulic (flux = 37 lmh) and organic loading (HRT = 2 hours and food-to-microorganism ratio = 0.33 g COD/g VSS x d) conditions. Water quality monitoring conducted throughout the study showed that each MBR system consistently produced an oxidized (5-day biochemical oxygen demand < 2 mg/L) and nitrified (ammonia < 1 mg-N/L) effluent low in particulate matter (turbidity < 0.1 NTU), under all conditions tested.     

吸附-预沉淀MBR工艺处理生活污水及膜污染控制效果

膜污染是限制膜生物反应器（MBR）广泛应用的主要因素之一。针对MBR处理生活污水过程中存在的硝化效果不稳定与膜污染问题,提出了一种新型的MBR系统：通过吸附-预沉淀实现进水中碳氮的分离和单独处理,不仅提高了污染物去除效果,且能够有效控制膜污染。研究结果表明,吸附-预沉淀可以去除进水中约89.7%的有机物,系统出水COD、NH₄⁺-N平均浓度为24 mg/L、0.78 mg/L,去除率分别为95.9%和98.1%。MBR中碳氮比的降低和硝化细菌比例的增加大大降低了MBR内MLSS、EPS和SMP含量,平均浓度分别为5 185 mg/L、41 mg/g MLSS和2.62 mg/g MLSS。在膜通量为4 L/（m²·h）条件下,TMP可稳定保持在20 kPa左右。通过吸附-预沉淀过程可有效控制MBR中的膜污染。     

A/O+MBR工艺处理玉米深加工废水的中试研究

实验基于企业污水站的改造工程,研究了MBR对玉米深加工废水的处理效果并对工艺运行参数优化提出建议.结果表明,该工艺对COD的去除率可以达到90％以上,出水稳定在26 mg/L左右;出水NH4-N达到1 mg/L以下;TN去除率达到70％以上,出水TN达到10 mg/L以下,出水完全达到排放标准.通过4种工况的比较,说明在污泥浓度8 g/L左右,曝气池内DO在3 mg/L左右,MBR内DO＞4 mg/L,好氧段停留时间13.5 h,并保证3h以上的缺氧段水力停留段时间的条件下,A/O+ MBR工艺可以有效去除玉米深加工废水中的污染物.     

MBR-NF截留液中腐植酸的纳滤分离浓缩特性

MBR-NF截留液是一类难处理的高浓度有机废水,其所含有机物几乎都是腐植酸,可考虑资源利用。实验室内采用纳滤对其所含腐植酸进行分离浓缩。引入分离因子来表征纳滤的分离效果。实验结果表明,分离因子(SF)与体积浓缩倍数(CF)有很好的线性关系,浓缩倍数为5时,截留液中有机碳浓度为9 413 mg/L,重金属浓度处于mg/L水平,分离因子达到2.76,表明纳滤可有效地将MBR-NF截留液中的腐植酸与无机盐分离,并进行浓缩。     

机械清洗法对MBR膜泥饼层的影响

膜污染是制约MBR发展的瓶颈。考察投加ABS颗粒对MBR膜组件上膜泥饼层的影响,并设对照实验。结果表明,对照MBR膜通量下降速度快,膜污染严重,膜表面上累积厚厚的泥饼层,而在ABS MBR中膜通量下降速度则缓慢的多,且膜上泥饼层积累量则明显少于对照MBR;曝气量越大,颗粒运行的速度也越快,泥饼层被撞落量也越多;颗粒以碰撞角度为45°冲刷膜的情况下,泥饼层掉落效果明显增加;泥饼层包裹的膜丝根数越多,泥饼层的静摩擦力和保持泥饼层不被破坏的力也越大,泥饼层就越难被冲刷掉。SEM照片显示,ABS MBR的膜孔堵塞要严重于对照MBR,表面的褶皱要较对照MBR多。     

两级序批式MBR除磷特性实验研究

为解决常规MBR工艺中脱氮除磷矛盾问题,采用新的工艺形式——两级序批式MBR工艺(两级SBMBR),对该工艺的除磷特性进行了实验研究。研究结果表明,在系统稳定运行阶段,SBMBR1内聚磷菌优势生长,进水总磷得以高效去除,再通过SBMBR2内膜的进一步截留,系统TP平均值0.46 mg/L,满足城市景观环境用水水质要求;在沉淀期间,POAs的释磷作用对生物除磷系统的影响甚至超过了水中剩余悬浮富磷污泥颗粒本身的影响,所以在满足沉淀要求的前提下,生物除磷系统应注意尽量缩短沉淀时间。