Exposure to ultrafine particles and PM2.5 in four Sydney transport modes

Concentrations of ultrafine (<0.1 μm) particles (UFPs) and PM_2.5 (<2.5 μm) were measured whilst commuting along a similar route by train, bus, ferry and automobile in Sydney, Australia. One trip on each transport mode was undertaken during both morning and evening peak hours throughout a working week, for a total of 40 trips. Analyses comprised one-way ANOVA to compare overall (i.e. all trips combined) geometric mean concentrations of both particle fractions measured across transport modes, and assessment of both the correlation between wind speed and individual trip means of UFPs and PM_2.5, and the correlation between the two particle fractions. Overall geometric mean concentrations of UFPs and PM_2.5 ranged from 2.8 (train) to 8.4 (bus) × 10⁴ particles cm^?3 and 22.6 (automobile) to 29.6 (bus) μg m^?3, respectively, and a statistically significant difference (p < 0.001) between modes was found for both particle fractions. Individual trip geometric mean concentrations were between 9.7 × 10³ (train) and 2.2 × 10⁵ (bus) particles cm^?3 and 9.5 (train) to 78.7 (train) μg m^?3. Estimated commuter exposures were variable, and the highest return trip mean PM_2.5 exposure occurred in the ferry mode, whilst the highest UFP exposure occurred during bus trips. The correlation between fractions was generally poor, and in keeping with the duality of particle mass and number emissions in vehicle-dominated urban areas. Wind speed was negatively correlated with, and a generally poor determinant of, UFP and PM_2.5 concentrations, suggesting a more significant role for other factors in determining commuter exposure.     

Concentrations of ultrafine,fine and PM2.5 particles in three European cities

Total number concentrations, number concentrations of ultrafine (0.01–0.1 μm) and accumulation (0.1–0.5 μm) particles, as well as mass concentration of PM_2.5 particles and blackness of PM_2.5 filters, which is related to Black Smoke were simultaneously monitored in three European cities during the winter period for three and a half months. The purpose of the study was to describe the differences in concentration levels and daily and diurnal variations in particle number and mass concentrations between European cities. The results show statistically significant differences in the concentrations of PM_2.5 and the blackness of the PM_2.5 filters between the cities, but not in the concentrations of ultrafine particles. Daily PM_2.5 levels were found to be poorly correlated with the daily total and ultrafine number concentrations but better correlated with the number concentration of accumulation particles. According to the principal component analysis airborne particulate pollutants seem to be divided into two major source categories, one identified with particle number concentrations and the other related to mass-based information. The present results underline the importance of using both particle number and mass concentrations to evaluate urban air quality.     

Sources and chemical composition of atmospheric fine and coarse particles in the Helsinki area

During April 1996–June 1997 size-segregated atmospheric aerosol particles were collected at an urban and a rural site in the Helsinki area by utilising virtual impactors (VI) and Berner low-pressure impactors (BLPI). In addition, VI samples were collected at a semi-urban site during October 1996–May 1997. The average PM_2.3 (fine particle) concentrations at the urban and rural sites were 11.8 and 8.4 μg/m³, and the PM_2.3−15 (coarse particle) concentrations were 12.8 and about 5 μg/m³, respectively. The difference in fine particle mass concentrations suggests that on average, more than one third of the fine mass at the urban site is of local origin. Evaporation of fine particle nitrate from the VI Teflon filters during sampling varied similarly at the three sites, the average evaporation being about 50–60%.The average fine particle concentrations of the chemical components (25 elements and 13 ions) appeared to be fairly similar at the three sites for most components, which suggests that despite the long-range transport, the local emissions of these components were relatively evenly distributed in the Helsinki area. Exceptions were the average fine particles Ba, Fe, Sb and V concentrations that were clearly highest at the urban site pointing to traffic (Ba, Fe, Sb) and to combustion of heavy fuel oil (V) as the likely local sources. The average coarse particle concentrations for most components were highest at the urban site and lowest at the rural site.Average chemical composition of fine particles was fairly similar at the urban and rural sites: non-analysed fraction (mainly carbonaceous material and water) 43% and 37%, sulphate 21% and 25%, crustal matter 12% and 13%, nitrate 12% and 11%, ammonium 9% and 10% and sea-salt 2.5% and 3.2%, respectively. At the semi-urban site also, the average fine particle composition was similar. At the urban site, the year round average composition of coarse particles was dominated by crustal matter (59%) and the non-analysed components (28%, mainly carbonaceous material and water), while the other contributions were much lower: sea-salt 7%, nitrate 4% and sulphate 2%. At the rural site, the coarse samples were collected in spring and summer and the percentage was clearly lower for crustal matter (37%) and sea-salt (3%) but higher for the not-analysed fraction (51%). At the semi-urban site, the average composition of coarse particles was nearly identical to that at the urban site.Correlations between the chemical components were calculated separately for fine and coarse particles. In urban fine particles sulphate, ammonium, Tl, oxalate and PM_2.3 mass correlated with each other and originated mainly from long-range transport. The sea-salt ions Na⁺, Cl⁻ and Mg²⁺ formed another group and still another group was formed by the organic anions oxalate, malonate, succinate, glutarate and methane sulphonate. Ni and V correlated strongly pointing to combustion of heavy fuel oil as the likely source. In addition, some groups with lower correlations were detected. At the rural and semi-urban sites, the correlating components were rather similar to those at the urban site, although differences were also observed.     

Chemical composition and source apportionment of PM2.5 particles in the Sihwa area, Korea

To investigate the chemical characteristics of fine particles in the Sihwa area, Korea, atmospheric aerosol samples were collected using a dichotomous PM10 sampler and two URG PM2.5 cyclone samplers during five intensive sampling periods between February 1998 and February 1999. The Inductively Coupled Plasma (ICP)-Atomic Emission Spectrometry (AES)/ICP-Mass Spectrometry (MS), ion chromatograph (IC), and thermal manganese dioxide oxidation (TMO) methods were used to analyze the trace elements, ionic species, and carbonaceous species, respectively. Backward trajectory analysis, factor analysis, and a chemical mass balance (CMB) model were used to estimate quantitatively source contributions to PM2.5 particles collected in the Sihwa area. The results of PM2.5 source apportionment using the CMB7 receptor model showed that (NH4)2SO4 was, on average, the major contributor to PM2.5 particles, followed by nontraffic organic carbon (OC) emission, NH4NO3, agricultural waste burning, motor vehicle emission, road dust, waste incineration, marine aerosol, and others. Here, the nontraffic OC sources include primary anthropogenic OC emitted from the industrial complex zone, secondary OC, and organic species from distant sources. The source impact of waste incineration emission became significant when the dominant wind directions were from southwest and west sectors during the sampling periods. It was found that PM2.5 particles in the Sihwa area were influenced mainly by both anthropogenic local sources and long-range transport and transformation of air pollutants.     

Ionic composition of PM(10) in the area of Thessaloniki,Greece

Airborne particulate matter (PM(10)) was collected from July 1997 to July 1998 at three locations in the city of Thessaloniki. PM(10) samples were analyzed for Cl(-), NO3(-), SO4(2-), Ca(2+), Mg(2+), Na(+), K(+) and NH4(+). The average PM(10) concentrations were found similar in all three sites with higher values in cold period. The ionic content comprised the 17-23% of the PM(10) mass and sulfate made up the 35-38% of the PM(10) ionic content with an average concentration of 4.80-7.26 microg m(-3). Good correlation was found for SO4(2-) and NO3(-) with Ca(2+), Mg(2+) and Cl(-). Two factors were found to influence the variance of ionic constituents in PM(10) by using factor analysis. Data evaluation considering wind direction showed that higher PM(10) and other ionic concentrations are associated with calm conditions, suggesting influences of local sources.     

Characterization and sources assignation of PM2.5 organic aerosol in a rural area of Spain

The results from a year-long study of the organic composition of PM2.5 aerosol collected in a rural area influenced by a highway of Spain are reported. The lack of prior information related to the organic composition of PM2.5 aerosol in Spain, concretely in rural areas, led definition of the goals of this study. As a result, this work has been able to characterize the main organic components of atmospheric aerosols, including several compounds of SOA, and has conducted a multivariate analysis in order to assign sources of particulate matter. A total of 89 samples were taken between April 2004 and April 2005 using a high-volume sampler. Features and abundance of n-alkanes, polycyclic aromatic hydrocarbons (PAHs), alcohols and acids were separately determined using gas chromatography/mass spectrometry and high performance liquid chromatography analysis. The Σn-alkane and ΣPAHs ranged from 3 to 81 ng m^?3 and 0.1 to 6 ng m^?3 respectively, with higher concentrations during colder months. Ambient concentrations of Σalcohols and Σacids ranged from 21 to 184 ng m^?3 and 39 to 733 ng m^?3, respectively. Also, several components of secondary organic aerosol have been quantified, confirming the biogenic contribution to ambient aerosol. In addition, factor analysis was used to reveal origin of organic compounds associated to particulate matter. Eight factors were extracted accounting more than 83% of the variability in the original data. These factors were assigned to a typical high pollution episode by anthropogenic particles, crustal material, plant waxes, fossil fuel combustion, temperature, microbiological emissions, SOA and dispersion of pollutants by wind action. Finally, a cluster analysis was used to compare the organic composition between the four seasons.     

Vertical profiles of ultrafine to supermicron particles measured by aircraft over Osaka metropolitan area in Japan

Intensive aircraft- and ground-based measurements of ultrafine to supermicron particles in the Osaka metropolitan area, Japan, were carried out on 17–19 March 2003, in order to investigate vertical profiles of size-resolved particles in the urban atmosphere. Differently sized particles were observed at different altitudes on 19 March. Relatively higher concentrations of ultrafine particles (31 nm) and submicron particles (0.3–0.5 μm) were measured (100–200 cm⁻³) at altitudes of 300 and 600 m, whereas supermicron particles (2–5 μm) were present (300–600 cm⁻³) at higher altitudes (1300 m in the morning and 2200 m in the afternoon). The chemical composition analysis showed that supermicron particles evidently comprised mainly soil particles mixed internally with anthropogenic species such as carbonaceous components and sulfate. Numerical simulation using the Chemical weather FORecasting System (CFORS) suggested the long-range transport of soil dust and black carbon from the Asian continent. Total number concentrations of particles sized 10–875 nm ranged from 4.8×10³ to 3.0×10⁴ cm⁻³ at an altitude of 300 m and from 7.3×10² to 4.8×10³ cm⁻³ at an altitude of 1300 m. Total number concentrations of particles sized 10–875 nm correlated very well with NO_X concentrations, and, therefore, ultrafine and submicron particles were likely emitted from urban activities such as car traffic and vertically transported. Number size distributions at lower altitudes obtained by aircraft measurements were similar to those obtained by ground measurements, with modal diameters of 20–30 nm on 18 March and about 50 nm on 19 March.     

Severe air pollution and characteristics of light-absorbing particles in a typical rural area of the Indo-Gangetic Plain

Environmental Science and Pollution Research - Total suspended particles (TSP) were collected in Lumbini from April 2013 to March 2016 to better understand the characteristics of carbonaceous...     

Water-soluble ions in nano/ultrafine/fine/coarse particles collected near a busy road and at a rural site

This study investigated water-soluble ions in the sized particles (particularly nano (PM(0.01-0.056))/ultrafine (PM(0.01-0.1))) collected using MOUDI and Nano-MOUDI samplers near a busy road site and at a rural site. The analytical results demonstrate that nano and coarse particles exhibited the highest (16.3%) and lowest (8.37%) nitrate mass ratios, respectively. The mass ratio of NO(3)(-) was higher than that of SO(4)(2-) in all the sized particles at the traffic site. The secondary aerosols all displayed trimodal distributions. The aerosols in ultrafine particles collected at the roadside site exhibited Aitken mode distributions indicating they were of local origin. This finding was not observed for those ultrafine particles collected at the rural site. The mass median diameters (MMDs) of the nano, ultrafine, and fine particles were smaller at the traffic site than at the rural site, possibly related to the contribution of mobile engine emissions.     

大气超细颗粒物观测和扩散模拟研究进展

总结了近年来不同地区对不同环境下大气超细颗粒物的观测和扩散模拟研究进展。大量的观测研究结果表明,大气超细颗粒物的时空分布、组成特征、形成和成长的特性因观测地区的不同而存在很大差异,受气象因素和局部污染源的影响很大;其来源主要包括固定、移动燃烧源的直接排放和大气中颗粒成核现象,前一种来源一般是局部的,而后一种来源则是区域性的。目前,大多数关于大气超细颗粒物扩散的模拟研究都是针对其质量浓度的,对其数浓度扩散的模拟研究主要集中在小范围(机动车排放烟云的研究方面),在城市区域范围上的研究和应用还很少。最后,探讨和展望了大气超细颗粒物今后的主要研究方向和研究中面临的挑战。     

Characterization of lead,cadmium, arsenic and nickel in PM(2.5) particles in the Athens atmosphere,Greece

Concentrations of Pb, Cd, As and Ni in PM(2.5) particles were measured in samples collected, using low volume PM(2.5) samplers (Harvard Impactor system, HI) at two sites in Athens basin; Patission Street in Athens city center and Rentis, a semi-urban and industrial area, during March 1995-March 1996. Sample analysis for Pb, Cd, Ni and As was accomplished by electrothermal atomic absorption spectrometry after total digestion. Annual geometric mean values in 183 PM(2.5) particles samples were found to be: Pb: 143 nanogram(-3); Cd: 0.34 nanogram(-3); Ni: 4.55 nanogram(-3); As: 0.79 nanogram(-3). The geographical and temporal distribution patterns were investigated. Pb exhibited higher values during the winter period. For the other elements no significant seasonal variation was observed. Wind direction, air temperature and relative humidity affected element concentrations. Principal component analysis was applied on the data to enable source apportionment of toxic elements in PM(2.5) particles. It was found that Pb, As and Ni have common sources, which could be vehicles emissions/oil combustion and resuspended road dust. Cd and a portion of As originate from industrial activities.     

Elemental characterization of PM10, PM2.5 and PM1 in the town of Genoa (Italy)

The particulate matter (PM) concentration and composition, the PM10, PM2.5, PM1 fractions, were studied in the urban area of Genoa, a coastal town in the northwest of Italy. Two instruments, the continuous monitor TEOM and the sequential sampler PARTISOL, were operated almost continuously on the same site from July 2001 to September 2004. Samples collected by PARTISOL were weighted to obtain PM concentration and then analysed by PIXE (particle induced X-ray emission) and by ED-XRF (energy dispersion X-ray fluorescence), obtaining concentrations for elements from Na to Pb. Some of the filters used in the TEOM microbalance were analysed by ED-XRF to calculate Pb concentration values averaged over 7-30 d periods.     

Temporal and spatial variation of the chemical composition of PM10 at urban and rural sites in the Basel area,Switzerland

Particulate matter measurements of different size fractions (PM₄, PM₁₀, TSP) were performed in the Basel area (Switzerland) at seven urban sites throughout 1997 and at two urban and two rural sites during the following year (April 1998–May 1999). Based on a sample of filters which was chemically analyzed, we investigated the chemical composition of PM₁₀ both within the city of Basel and among urban and rural sites. The temporal and spatial variability of the chemical composition of PM₁₀ was evaluated taking into account additional data from meteorology and further air pollutants. The chemical analyses of PM₁₀ showed that carbonaceous substances (elemental carbon, organic matter) and inorganic substances of secondary origin such as sulfate, nitrate and ammonium were the most abundant component of PM₁₀ in the Basel area (approximately 60–70%). Difference in the PM₁₀ concentration between urban and rural sites was larger during the cold season than during the warm season. This was mainly due to the presence of an inversion layer between the city and the more elevated rural sites resulting in higher concentrations of nitrate, ammonium and organic matter in the city during the cold season. The higher PM₁₀ concentration on workdays compared to weekends was mostly a result of the temporal variation of the concentration of Ca, elemental carbon, Ti, Mn, and Fe, indicating that these compounds are for the most part caused by regional human activities. Although total PM₁₀ mass concentration was found to be in general uniformly distributed within the city of Basel, the chemical composition was more variable due to specific sources like road traffic and other anthropogenic emissions.     

Intake fraction distributions for benzene from vehicles in the Helsinki metropolitan area

The intake fraction (iF) gives a measure of the portion of a source's emissions that is inhaled by an exposed population over a defined period of time. This study examines spatial and population-based iF distributions of a known human carcinogen, benzene, from a ubiquitous urban source, local vehicular traffic, in the Helsinki Metropolitan Area using three computational methods. The first method uses the EXPAND model (EXPosure to Air pollution, especially to Nitrogen Dioxide and particulate matter), which incorporates spatial and temporal information on population activity patterns as well as urban-scale and street canyon dispersion models to predict spatial population exposure distributions. The second method uses data from the personal monitoring study EXPOLIS (Air Pollution Exposure Distributions of Adult Urban Populations in Europe) to estimate the intake fractions for individuals in the study. The third method, a one-compartment box model provides estimates within an order-of-magnitude or better for non-reactive agents in an urban area. Population intake fractions are higher using the personal monitoring data method (median iF 30 per million, mean iF 39 per million) compared with the spatial model (annual mean iF 10 per million) and the box model (median iF 4 per million, mean iF 7 per million). In particular, this study presents detailed intake fraction distributions on several different levels (spatial, individual, and generic) for the same urban area.     

Comparison of two estimation methods for surface area concentration using number concentration and mass concentration of combustion-related ultrafine particles

Recent research has suggested that the adverse health effects caused by nanoparticles are associated with their surface area (SA) concentrations. In this study, SA was estimated in two ways using number and mass concentrations and compared with SA (SA_meas) measured using a diffusion charger (DC). Aerosol measurements were made twice: once starting in October 2002 and again starting in December 2002 in Mysore, India in residences that used kerosene or liquefied petroleum gas (LPG) for cooking. Mass, number, and SA concentrations and size distributions by number were measured in each residence. The first estimation method (SA_PSD) used the size distribution by number to estimate SA. The second method (SA_INV) used a simple inversion scheme that incorporated number and mass concentrations while assuming a lognormal size distribution with a known geometrical standard deviation. SA_PSD was, on average, 2.4 times greater (range = 1.6–3.4) than SA_meas while SA_INV was, on average, 6.0 times greater (range = 4.6–7.7) than SA_meas. The logarithms of SA_PSD and SA_INV were found to be statistically significant predictors of the logarithm of SA_meas. The study showed that particle number and mass concentration measurements can be used to estimate SA with a correction factor that ranges between 2 and 6.     

Measurements of fine and ultrafine particles formation in photocopy centers in Taiwan

This study investigates the levels of particulate matter smaller than 2.5 μm (PM_2.5) and some selected volatile organic compounds (VOCs) at 12 photocopy centers in Taiwan from November 2004 to June 2005. The results of BTEXS (benzene, toluene, ethylbenzene, xylenes and styrene) measurements indicated that toluene had the highest concentration in all photocopy centers, while the concentration of the other four compounds varied among the 12 photocopy centers. The average background-corrected eight-hour PM_2.5 in the 12 photocopy centers ranged from 10 to 83 μg m⁻³ with an average of 40 μg m⁻³. The 24-h indoor PM_2.5 at the photocopy centers was estimated and at two photocopy centers exceeded 100 μg m⁻³, the 24-h indoor PM_2.5 guideline recommended by the Taiwan EPA. The ozone level and particle size distribution at another photocopy center were monitored and indicated that the ozone level increased when the photocopying started and the average ozone level at some photocopy centers during business hour may exceed the value (50 ppb) recommended by the Taiwan EPA. The particle size distribution monitored during photocopying indicated that the emitted particles were much smaller than the original toner powders. Additionally, the number concentration of particles that were smaller than 0.5 μm was found to increase during the first hour of photocopying and it increased as the particle size decreased. The ultrafine particle (UFP, <100 nm) dominated the number concentration and the peak concentration appeared at sizes of under 50 nm. A high number concentration of UFP was found with a peak value of 1E+8 particles cm⁻³ during photocopying. The decline of UFP concentration was observed after the first hour and the decline is likely attributable to the surface deposition of charged particles, which are charged primarily by the diffusion charging of corona devices in the photocopier. This study concludes that ozone and UFP concentrations in photocopy centers should be concerned in view of indoor air quality and human health. The corona devices in photocopiers and photocopier-emitted VOCs have the potential to initiate indoor air chemistry during photocopying and result in the formation of UFP.     

PM10 and PM2.5 source apportionment in the Barcelona Metropolitan area, Catalonia, Spain

Levels of total suspended particles, PM10, PM2.5 and PM1 were continuously monitored at an urban kerbside in the Metropolitan area of Barcelona from June 1999 to June 2000. The results show that hourly levels of PM2.5 and PM1 are consistent with the daily cycle of gaseous pollutants emitted by traffic, whereas TSP and PM10 do not follow the same trend, at least in the diurnal period. The PM2.5/PM10 ratio is dependent on the traffic emissions, whereas additional contribution sources for the >10 μm fraction must be taken into account in the diurnal period. Different PM10 and PM2.5 source apportionment techniques were compared. A methodology based on the chemical determination of 83% of both PM10 and PM2.5 masses allowed us to quantify the marine (4% in PM10 and <1% in PM2.5), crustal (26% in PM10 and 8% in PM2.5) and anthropogenic (54% in PM10 and 73% in PM2.5) loads. Peaks of crustal contribution to PM10 (up to 44% of the PM10 mass) were recorded under Saharan air mass intrusions. A different seasonal trend was observed for levels of sulphate and nitrate, probably as a consequence of the different thermodynamic behaviour of these PM species and the higher summer oxidation rate of SO₂.     

Source apportionment of fine particulate matter (PM2.5) at a rural Ohio River Valley site

Twenty four-hour averaged concentrations of fine particulate matter were collected at Athens, OH between March 2004 and November 2005 in an effort to characterize the nature of PM_2.5 and apportion its sources. PM_2.5 samples were chemically analyzed and positive matrix factorization was applied to this speciation data to identify the probable sources. PMF arrived at a 7-factor model to most accurately apportion sources of the PM_2.5 observed at Athens. Conditional probability function (CPF) and potential source contribution function (PSCF) were applied to the identified sources to investigate the geographical location of these sources. Secondary sulfate source dominated the contributions with a total contribution of 62.6% with the primary and secondary organic source following second with 19.9%. Secondary nitrate contributed a total of 6.5% with the steel production source and Pb- and Zn-source coming in at 3.1% and 2.9%, respectively. Crustal and mobile sources were small contributors (2.5% each) of PM_2.5 to the Athens region. The secondary sulfate, secondary organic and nitrate portrayed a clear seasonal nature with the sulfate and secondary organic peaking in the warm months and the nitrate reaching a high in the cold months. The high percentage of secondary sulfate observed at a rural site like Athens suggests the involvement of regional transport mechanisms.     

Anthropogenic and natural influence on the PM(10) and PM(2.5) aerosol in Madrid (Spain). Analysis of high concentration episodes

Non-mineral carbon is the main component of PM10 and PM2.5 at an urban roadside site in Madrid accounting for more than 50% of the total bulk mass in winter pollution episodes. In these cases a 70-80% of the particle mass is anthropogenic. Particles of crustal/mineral origin contribute significantly to the observed PM10 concentrations, especially in spring and summer. They have also been found in the PM2.5 fraction although secondary particles are the next most important contributor in this size. Long-range transport particle episodes of Saharan dust significantly contribute to exceedence of the new daily limiting PM10 value in the urban network and at nearby rural background stations. This type of long-range transport event also influences PM2.5 concentrations. The crustal contribution can account for up to 67 and 53% of the PM10 and PM2.5 bulk mass in such cases.     

Use of atmospheric elemental size distributions in estimating aerosol sources in the Helsinki area

In June 1996–June 1997 Berner impactors were used in the Helsinki area to measure size distributions of atmospheric aerosols simultaneously at an urban and at a rural site. Ten sample pairs were collected in the size range of 0.03–15.7 μm of equivalent aerodynamic diameter (EAD). Average size distributions at the two sites were calculated for 29 elements, particulate mass, and sulphate. At both sites especially sulphate, As, B, Bi, Cd, Ni, Tl, and V were enriched in fine particles (EAD<2.3 μm). In order to estimate local fine-particle sources of the various chemical components, the similarities and dissimilarities in the accumulation-mode parameters were studied separately for both sites. It was observed that often in different samples, different components had similar accumulation modes. At both sites, particulate mass, As, and Pb had similar accumulation modes to sulphate which suggests that long-range transport (LRT) is important for these components. V, Ni, Mo, and Co formed another group of similar accumulation modes at both sites suggesting that these elements largely originated from local and regional oil combustion. In addition, other groups of similar accumulation modes were observed but these groups were different between the sites. The meteorological parameters indicated that seven sample pairs formed a subset of the data in which the local emissions of the Helsinki area were transported to the urban site but not to the rural site. For this subset the rural fine-particle concentrations were considered to represent an upper limit estimate for the LRT. These upper limit LRT estimations were further improved by utilising the quantitative relative size distributions (QRSD) method at the rural site. The QRSD method supposes that in the fine-particle size range the LRT fractions of all chemical components have a similar shape in their size distributions. Fine-particle sulphate is typically long-range transported, and was therefore selected as the model component that represents the shape of LRT material. Sulphate size distribution was then scaled to give an estimation of the LRT contribution of each component at the rural site. These rural “sulphate scaled” LRT estimates were subtracted from the corresponding urban concentrations to give the local contributions (ng/m³) downwind of the Helsinki area. In particles with EAD below 2.3 μm, the highest absolute and relative downwind local contributions were observed for several common sea-salt and road-dust components. Also the combustion-related elements Ni and V showed fairly high downwind local contributions. Because of the limited number of samples, the local and LRT contributions were not estimated for different wind directions.