Measurement of the vertical profile of atmospheric SO2 during the heating period in Beijing on days of high air pollution

This paper reports altitude-resolved concentrations of sulfur dioxide (SO₂) and particulate matter up to 10 microns in diameter (PM₁₀) in the planetary boundary layer of major urban centers during extreme pollution episodes. The concentration of SO₂ was observed continuously from November 24, 2004, to December 4, 2004, in Beijing during the heating period. Fluorescence SO₂ analyzers were used to measure the atmospheric SO₂ concentrations. Four SO₂ analyzers were placed at 4 different levels (8 m, 47 m, 120 m, and 280 m) of the 325-m high meteorological observation tower of the Institute of Atmospheric Physics (IAP), Chinese Academy of Sciences. A maximal SO₂ concentration of 172.3 ppb was measured during this pollution episode, and SO₂ concentration increased with altitude and reached its maximal value at ～50 m. The study also analyzed the meteorological situation before, during, and after the pollution episode.     

Application of a Lagrangian particle model to assess the impact of harbour,industrial and urban activities on air quality in the Taranto area,Italy

This paper evaluates the relative impact on air quality of harbour emissions, with respect to other emission sources located in the same area. The impact assessment study was conducted in the city of Taranto, Italy. This area was considered as representative of a typical Mediterranean harbour region, where shipping, industries and urban activities co-exist at a short distance, producing an ideal case to study the interaction among these different sources. Chemical and meteorological field campaigns were carried out to provide data to this study. An emission inventory has been developed taking into account industrial sources, traffic, domestic heating, fugitive and harbour emissions. A 3D Lagrangian particle dispersion model (SPRAY) has then been applied to the study area using reconstructed meteorological fields calculated by the diagnostic meteorological model MINERVE. 3D short term hourly concentrations have been computed for both all and specific sources. Industrial activities are found to be the main contributor to SO₂. Industry and traffic emissions are mainly responsible for NO_x simulated concentrations. CO concentrations are found to be mainly related to traffic emissions, while primary PM₁₀ simulated concentrations tend to be linked to industrial and fugitive emissions. Contributions of harbour activities to the seasonal average concentrations of SO₂ and NO_x are predicted to be up to 5 and 30 μg m⁻³, respectively to be compared to a overall peak values of 60 μg m⁻³ for SO₂ and 70 μg m⁻³ for NO_x. At selected urban monitoring stations, SO₂ and NO_x average source contributions are predicted to be both of about 9% from harbour activities, while 87% and 41% respectively of total concentrations are predicted to be of industrial origin.     

A simple technique for measuring power station SO2 and NO2 emissions

Emissions of SO₂ and NO₂ from fossil fuel power stations can have serious environmental consequences via conversion to sulphuric and nitric acids and subsequent deposition. Consequently, there is considerable interest in techniques capable of monitoring these emissions, in order to ensure compliance with environmental legislation. Here we present a novel approach to measuring power station SO₂ and NO₂ emissions by traversing underneath the plume by car or on-foot or scanning the power station's plume from a fixed position with a compact and lightweight UV spectrometer. This work was performed at a power station in eastern England during January, February and June 2003, resulting in a SO₂ flux of 5.2 kg s⁻¹, which is in close correspondence with the in-stack measured value of 5.3 kg s⁻¹. This technique is considerably simpler and cheaper than other remote sensing approaches to monitoring these emissions.     

Dilution and aerosol dynamics within a diesel car exhaust plume—CFD simulations of on-road measurement conditions

Vehicle particle emissions are studied extensively because of their health effects, contribution to ambient PM levels and possible impact on climate. The aim of this work was to obtain a better understanding of secondary particle formation and growth in a diluting vehicle exhaust plume using 3-d information of simulations together with measurements. Detailed coupled computational fluid dynamics (CFD) and aerosol dynamics simulations have been conducted for H₂SO₄–H₂O and soot particles based on measurements within a vehicle exhaust plume under real conditions on public roads.Turbulent diffusion of soot and nucleation particles is responsible for the measured decrease of number concentrations within the diesel car exhaust plume and decreases coagulation rates. Particle size distribution measurements at 0.45 and 0.9 m distance to the tailpipe indicate a consistent soot mode (particle diameter D_p∼50 nm) at variable operating conditions. Soot mode number concentrations reached up to 10¹³ m⁻³ depending on operating conditions and mixing.For nucleation particles the simulations showed a strong sensitivity to the spatial dilution pattern, related cooling and exhaust H₂SO_4(g). The highest simulated nucleation rates were about 0.05–0.1 m from the axis of the plume. The simulated particle number concentration pattern is in approximate accordance with measured concentrations, along the jet centreline and 0.45 and 0.9 m from the tailpipe. Although the test car was run with ultralow sulphur fuel, high nucleation particle (D_p⩽15 nm) concentrations (>10¹³ m⁻³) were measured under driving conditions of strong acceleration or the combination of high vehicle speed (>140 km h⁻¹) and high engine rotational speed (>3800 revolutions per minute (rpm)).Strong mixing and cooling caused rapid nucleation immediately behind the tailpipe, so that the highest particle number concentrations were recorded at a distance, x=0.45 m behind the tailpipe. The simulated growth of H₂SO₄–H₂O nucleation particles was unrealistically low compared with measurements. The possible role of low and semi-volatile organic components on the growth processes is discussed. Simulations for simplified H₂SO₄–H₂O–octane–gasoil aerosol resulted in sufficient growth of nucleation particles.     

Regional dispersion of oxidized sulfur in Central Chile

Chile has a long tradition of exploiting mineral resources, particularly copper (Cu). One of the largest Cu smelters, Caletones, located some 150 km south of the country's capital, Santiago, in Central Chile, is responsible for about 0.4% of about 70 Tg S/yr oxidized sulfur (SO_x) emitted by anthropogenic sources worldwide. Santiago, a megacity with 5 million inhabitants, stands for about 5 Gg S/yr. The average meteorological conditions are unfavorable for the dispersion of pollutants in this area. All this poses risks for human health and vegetation. Also, downwind from these polluted areas there may be large-scale impacts on cloud properties and on oxidative cycles. Here, we present the first attempt to assess the regional distribution of SO_x in Central Chile using a dispersion model (MATCH) driven with data from a limited area weather forecast model (HIRLAM). Emphasis has been given to the impact of Cu smelters upon urban air quality, particularly that of Santiago. Six 1-month long periods were simulated for the years 1997, 1998 and 1999. These periods span over a broad range of typical meteorological conditions in the area including El Niño and La Niña years. Estimates of the regional dispersion and deposition patterns were calculated. The emissions from the large Cu smelters dominate the distribution of SO_x. A budget of SO_x over an area of 200×200 km² around Santiago is presented. There is too low a number of monitoring stations to perform a detailed evaluation of MATCH. Nevertheless, the model reproduces consistently all the regional-scale characteristics that can be derived from the available observations.     

NOy removal from the Cumberland Power Plant Plume

Airborne measurements were performed in the plume of the Cumberland Power Plant during August 1998 using a highly sensitive SO₂ instrument. The measurements confirmed previous suggestions that NO_y species are removed from the plume at a faster rate than SO₂. The differential removal rate (the difference between loss rate of NO_y and that of SO₂) was estimated to be 0.06 h⁻¹. This value implies that the NO_y loss rate is in the range of 0.09–0.14 h⁻¹. The application of a mathematical argument, based on the convolution integral, enabled improved synchronization of the data from the SO₂ and NO_y instruments. Examination of the synchronized data revealed that the concentration ratio of SO₂ and NO_y varies across the plume. Near the source it is higher at the wings of the plume, while in the core of the plume it is similar to the ratio at the release point. Two possible explanations of the observations are discussed: conversion to non-measurable NO_y species, and in-plume loss of NO_y (as HNO₃) via dry deposition.     

Identification and assessment of ship emissions and their effects in the harbour of Göteborg,Sweden

The effect of ship emissions in the urban environment of Göteborg has been studied by multivariate analysis. The simultaneous measurements of relevant gases and sub-micron particles make identification of ship plumes possible. Increased concentrations of these species due to ship emissions are quantified for ships entering the inner part of the harbour. Annual depositions of SO₂ and NO₂ are estimated to be 220 and 115 kg km⁻² yr⁻¹, respectively. Exposure of transient particles (less than 0.1 μm in diameter) to this part of the harbour increased by a factor of 3 in number concentration when a ship plume was recorded. Ni, Pb, V and Zn are shown to have positive correlation with NO emissions from ships.     

Ambient sulfur dioxide,nitrogen dioxide,and ammonia at ten background and rural sites in China during 2007–2008

We present two years (January 2007–December 2008) of atmospheric SO₂, NO₂ and NH₃ measurements from ten background or rural sites in nine provinces in China. The measurements were made on a monthly basis using passive samplers under careful quality control. The results show large geographical and seasonal variations in the concentrations of these gases. The mean SO₂ concentration varied from 0.7 ± 0.4 ppb at Waliguan on Qinghai Plateau to 67.3 ± 31.1 ppb at Kaili in Guizhou province. The mean NO₂ concentration ranged from 0.6 ± 0.4 ppb at Waliguan to 23.9 ± 6.9 ppb at Houma in southern Shanxi. The mean NH₃ concentration ranged from 2.8 ± 3.0 ppb at Shangdianzi in northeastern Beijing to 13.7 ± 8.4 ppb at Houma. At most sites, SO₂ and NO₂ peaked in winter and reached minima in summer, while NH₃ showed maximum values in summer and lower values in cold seasons. On the whole, the geographical distributions of the observed gas concentrations are consistent with those of emissions. The ground measurements of SO₂ and NO₂ are contrasted to the SCIAMACHY SO₂ and OMI NO₂ tropospheric columns, respectively. Although the satellite data can capture the main features of emissions and concentrations of SO₂, they do not reflect the variations of SO₂ in the surface layer. The situation is better for the case of NO₂. The OMI NO₂ columns capture the geographical differences in the ground NO₂ and correlate fairly well with the ground levels of NO₂ at six of the ten sites.     

Long-term measurements of SO2 dry deposition over Gansu Province,China

Potassium carbonate sulfation plates, monitored monthly for 11 years from 48 sites in 11 cities in Gansu Province, China, provide a crude estimate of cumulative SO₂ dry depositions. Measured SO₂ dry deposition rates were 1.6–472 mg m⁻² day⁻¹ and had seasonal variations with maxima in winter and minima mainly during summer as a result of higher winter and lower summer SO₂ concentrations. The 11-year monthly average SO₂ dry deposition rates are 23.2–248.97 and 11.7–175.6 mg m⁻² day⁻¹ in the eleven cities in winter and summer, respectively. A monthly average SO₂ deposition velocity was also estimated from 0.06 to 9.72 cm s⁻² in the 11 cities studied with a 11-year average maximum value of about 1.1–2.7 cm s⁻² in April and July and a 11-year average minimum value of about 0.2–1.0 cm s⁻¹ in January. The SO₂ dry deposition velocity also exhibits an increasing with wind speed in basins of less than 500 mm annual precipitation. In contrast, due to influences of the relative humidity in valleys of more than 500 mm annual precipitation, it shows a decreasing trend with wind speed increasing.     

Trace gas variations at Cape Point,South Africa,during May 1997 following a regional biomass burning episode

During the continuous monitoring of atmospheric parameters at the station Cape Point (34°S, 18°E), a smoke plume originating from a controlled fire of 30-yr-old fynbos was observed on 6 May 1997. For this episode, which was associated with a nocturnal inversion and offshore airflow, atmospheric parameters (solar radiation and meteorological data) were considered and the levels of various trace gases compared with those measured at Cape Point in maritime air. Concentration maxima in the morning of 6 May for CO₂, CO, CH₄ and O₃ amounted to 370.3 ppm, 491 ppb, 1730 ppb and 47 ppb, respectively, whilst the mixing ratios of several halocarbons (F-11, F-12, F-113, CCl₄ and CH₃CCl₃) remained at background levels. In the case of CO, the maritime background level for this period was exceeded by a factor of 9.8. Differences in ozone levels of up to 5 ppb between air intakes at 4 and 30 m above the station (located at 230 m above sea level) indicated stratification of the air advected to Cape Point during the plume event. Aerosols within the smoke plume caused the signal of global solar radiation and UV–A to be attenuated from 52.4 to 13.0 mW cm⁻² and from 2.3 to 1.3 mW cm⁻², respectively, 5 h after the trace gases had reached their maxima. Emission ratios (ERs) calculated for CO and CH₄ relative to CO₂ mixing ratios amounted to 0.042 and 0.0040, respectively, representing one of the first results for fires involving fynbos. The CO ER is somewhat lower than those given in the literature for African savanna fires (average ER=0.048), whilst for CH₄ the ER falls within the range of ERs reported for the flaming (0.0030) and smouldering phases (0.0055) of savanna fires. Non-methane hydrocarbon (NMHC) data obtained from a grab sample collected during the plume event were compared to background levels. The highest ERs (ΔNMHC/ΔCH₄) have been obtained for the C₂–C₃ hydrocarbons (e.g. ethene at 229.3 ppt ppb⁻¹), whilst the C₄–C₇ hydrocarbons were characterised by the lowest ERs (e.g. n-hexane at 1.0 and n-pentane at 0.8 ppt ppb⁻¹).     

Efflorescence relative humidity of airborne sodium chloride particles: A theoretical investigation

The previously developed theoretical model [Gao, Y., Chen, S.B., Yu, L.E., 2006. Efflorescence relative humidity for ammonium sulfate particles. Journal of Physical Chemistry A, 110, 7602–7608], which has successfully predicted the efflorescence relative humidity (ERH) of ammonium sulfate ((NH₄)₂SO₄) particles at room temperature, is employed to estimate the ERH of sodium chloride (NaCl) particles in sizes ranging from 6 nm to 20 μm. The theoretical predictions well agree with the reported experimental data in literatures. When the NaCl particles are larger than 70 nm, the ERH decreases with decreasing dry particle sizes, and reach a minimum around 44% RH, otherwise the ERH increases with decreasing dry particle sizes (<70 nm) because of the Kelvin effect. Compared with (NH₄)₂SO₄ particles, the Kelvin effect on ERH is stronger for NaCl particles smaller than 30 nm, while the dry particle size exerts weaker influence on NaCl particles larger than 70 nm.     

Photochemical oxidation and dispersion of gaseous sulfur compounds from natural and anthropogenic sources around a coastal location

The photochemical oxidation and dispersion of reduced sulfur compounds (RSCs: H₂S, CH₃SH, DMS, CS₂, and DMDS) emitted from anthropogenic (A) and natural (N) sources were evaluated based on a numerical modeling approach. The anthropogenic emission concentrations of RSCs were measured from several sampling sites at the Donghae landfill (D-LF) (i.e., source type A) in South Korea during a series of field campaigns (May through December 2004). The emissions of natural RSCs in a coastal study area near the D-LF (i.e., source type N) were estimated from sea surface DMS concentrations and transfer velocity during the same study period. These emission data were then used as input to the CALPUFF dispersion model, revised with 34 chemical reactions for RSCs. A significant fraction of sulfur dioxide (SO₂) was produced photochemically during the summer (about 34% of total SO₂ concentrations) followed by fall (21%), spring (15%), and winter (5%). Photochemical production of SO₂ was dominated by H₂S (about 55% of total contributions) and DMS (24%). The largest impact of RSCs from source type A on SO₂ concentrations occurred around the D-LF during summer. The total SO₂ concentrations produced from source type N around the D-LF during the summer (a mean SO₂ concentration of 7.4 ppbv) were significantly higher than those (≤0.3 ppbv) during the other seasons. This may be because of the high RSC and SO₂ emissions and their photochemistry along with the wind convergence.     

The impact of an 8 h ozone air quality standard on ROG and NOx controls in Southern California

The new National Ambient Air Quality Standard for ozone in the US uses 8 h averaging for the concentration. Based on the 1993 ambient data for Southern California, 8 h averaging has a moderate tendency to move the location of the peak ozone concentration east of the location of the peak 1 h ozone concentration. Reducing the area-wide peak 8 h ozone concentration to 80 ppb would require an effective reduction of the area-wide peak 1 h ozone concentration to around 90 ppb. The Urban Airshed Model with improved numerical solvers, meteorological input based on a mesoscale model and an adjusted emissions inventory was used to study the effect of reactive organic gases (ROG) and NO_x controls on daily-maximum and peak 8 h ozone concentrations under the 26–28 August 1987 ozone episodic conditions in Southern California. The NO_x disbenefit remains prominent for the case of 8 h ozone concentration but is somewhat less prominent, especially when areal ozone exposure is considered, than the case for 1 h ozone concentration. The role of two indicators – O₃/NO_y and H₂O₂/HNO₃ – for NO_x- and ROG-sensitivity for 1 and 8 h ozone concentrations were also studied. In general, the indicator trends are consistent with model predictions, but the discriminating power of the indicators is rather limited.     

Evaluation of SO2 dry deposition over short vegetation in Portugal

SO₂ dry deposition was studied over short vegetation, in Portugal, by means of the concentration gradient method. The experimental study involved one first phase of long-term measurements carried out in a grassland and, subsequently, a second period of several 1997 intensive field campaigns performed in three places representing different climate and surface conditions. Temporal and spatial patterns of dry deposition parameters show that downward fluxes of SO₂ are by some extent affected by surface processes. Median R_c varied from 140 s cm⁻¹ to values around 200 s cm⁻¹, in a wide range of environmental conditions. Stomatal uptake is an important sink when vegetation is biologically active, but its contribution is effectively low when compared with non-stomatal mechanisms, especially when the surface is wet. Under dry conditions R_c increases by a factor of two, but SO₂ deposition rates then still are significant. The parameterisation of the surface resistance for SO₂ proved to be difficult, but V_d derived with the Erisman parameterisation (Erisman et al., Atmos. Environ. 28 (16) (1994) 2595) compared best with measured values, at low time resolution scale and especially under moisture conditions.     

Distribution of seasonal SO2 emissions from fuel combustion and industrial activities in Shanxi province,China, with 1/6°×1/4° longitude/latitude resolution

Spatial distribution of SO₂ emission inventory for 1994 from fuel combustion and industrial activities in Shanxi province, the Peoples’ Republic of China, has been created with 1/6°×1/4° latitude/longitude resolution. Total annual SO₂ emissions in 1994 in the province were estimated to be 669 GgS, of which 180 GgS were emitted in winter, 170 GgS in spring, 156 GgS in summer, and 163 GgS in fall. For the first time this emission inventory includes SO₂ emissions from village and township enterprises. Although SO₂ emissions from major industries were under control, SO₂ emissions from village and township enterprises became the major threat to the environment in the province.     

Observations and modelling of aerosol growth in marine stratocumulus—case study

Airborne measurements of the growth of the marine accumulation mode after multiple cycles through stratocumulus cloud are presented. The nss-sulphate cloud residual mode was log-normal in spectral shape and it’s mode radius was observed to progressively increase in size from 0.78 to 0.94 μm over 155 min of air parcel evolution through the cloudy marine boundary layer. The primary reason for this observed growth was thought to result from aqueous phase oxidation of SO₂ to aerosol sulphate in activated cloud drops. An aqueous phase aerosol–cloud-chemistry model was used to simulate this case study of aerosol growth and was able to closely reproduce the observed growth. The model simulations illustrate that aqueous phase oxidation of SO₂ in cloud droplets was able to provide enough additional sulphate mass to increase the size of activated aerosol. During a typical cloud cycle simulation, ≈4.6 nmoles kg^-1_air (0.44 μg m^-3) of sulphate mass was produced with ≈70% of sulphate production occurring in cloud droplets activated upon sea-salt nuclei and ≈30% occurring upon nss-sulphate nuclei, even though sea-salt nuclei contributed less than 15% to the activated droplet population. The high fraction of nss-sulphate mass internally mixed with sea-salt aerosol suggests that aqueous phase oxidation of SO₂ in cloud droplets activated upon sea-salt nuclei is the dominant nss-sulphate formation mechanism and that sea-salt aerosol provides the primary chemical sink for SO₂ in the cloudy marine boundary layer.     

Assessment of air quality benefits from national air pollution control policies in China. Part II: Evaluation of air quality predictions and air quality benefits assessment

Following the meteorological evaluation in Part I, this Part II paper presents the statistical evaluation of air quality predictions by the U.S. Environmental Protection Agency (U.S. EPA)’s Community Multi-Scale Air Quality (Models-3/CMAQ) model for the four simulated months in the base year 2005. The surface predictions were evaluated using the Air Pollution Index (API) data published by the China Ministry of Environmental Protection (MEP) for 31 capital cities and daily fine particulate matter (PM_2.5, particles with aerodiameter less than or equal to 2.5 μm) observations of an individual site in Tsinghua University (THU). To overcome the shortage in surface observations, satellite data are used to assess the column predictions including tropospheric nitrogen dioxide (NO₂) column abundance and aerosol optical depth (AOD). The result shows that CMAQ gives reasonably good predictions for the air quality.The air quality improvement that would result from the targeted sulfur dioxide (SO₂) and nitrogen oxides (NO_x) emission controls in China were assessed for the objective year 2010. The results show that the emission controls can lead to significant air quality benefits. SO₂ concentrations in highly polluted areas of East China in 2010 are estimated to be decreased by 30–60% compared to the levels in the 2010 Business-As-Usual (BAU) case. The annual PM_2.5 can also decline by 3–15 μg m^?3 (4–25%) due to the lower SO₂ and sulfate concentrations. If similar controls are implemented for NO_x emissions, NO_x concentrations are estimated to decrease by 30–60% as compared with the 2010 BAU scenario. The annual mean PM_2.5 concentrations will also decline by 2–14 μg m^?3 (3–12%). In addition, the number of ozone (O₃) non-attainment areas in the northern China is projected to be much lower, with the maximum 1-h average O₃ concentrations in the summer reduced by 8–30 ppb.     

Aircraft measurements of O3, NOx,CO, VOCs,and SO2 in the Yangtze River Delta region

In this study, air pollutants, including ozone (O₃), nitrogen oxides (NO_x = NO + NO₂), carbon monoxides (CO), sulfur dioxide (SO₂), and volatile organic compounds (VOCs) measured in the Yangtze River Delta (YRD) region during several air flights between September/30 and October/11 are analyzed. This measurement provides horizontal and vertical distributions of air pollutants in the YRD region. The analysis of the result shows that the measured O₃ concentrations range from 20 to 60 ppbv. These values are generally below the US national standard (84 ppbv), suggesting that at the present, the O₃ pollutions are modest in this region. The NO_x concentrations have strong spatial and temporal variations, ranging from 3 to 40 ppbv. The SO₂ concentrations also have large spatial and temporal variations, ranging from 1 to 35 ppbv. The high concentrations of CO are measured with small variations, ranging from 3 to 7 ppmv. The concentrations of VOCs are relatively low, with the total VOC concentrations of less than 6 ppbv. The relative small VOC concentrations and the relative large NO_x concentrations suggest that the O₃ chemical formation is under a strong VOC-limited regime in the YRD region. The measured O₃ and NO_x concentrations are strongly anti-correlated, indicating that enhancement in NO_x concentrations leads to decrease in O₃ concentrations. Moreover, the O₃ concentrations are more sensitive to NO_x concentrations in the rural region than in the city region. The ratios of Δ[O₃]/Δ[NO_x] are ?2.3 and ?0.25 in the rural and in the city region, respectively. In addition, the measured NO_x and SO₂ concentrations are strongly correlated, highlighting that the NO_x and SO₂ are probably originated from same emission sources. Because SO₂ emissions are significantly originated from coal burnings, the strong correlation between SO₂ and NO_x concentrations suggests that the NO_x emission sources are mostly from coal burned sources. As a result, the future automobile increases could lead to rapid enhancements in O₃ concentrations in the YRD region.     

Estimation of wind blown dust emissions in Europe and its vicinity

The assessment of the wind blown dust emission for Europe and selected regions of North Africa and Southwest Asia was carried out using a mesoscale model. The mesoscale model was parameterized based on the current literature review. The model provides data on PM₁₀ emission from several dust reservoirs (anthropogenic, agriculture, semi- and natural) with spatial resolution of 10 × 10 km and temporal resolution of 1 h. The spatial variability of PM₁₀ emission depends on soil texture, land cover/land use as well as meteorological conditions. Lands covered with water or permanently wet were excluded from the model. The land covered with vegetation is treated as dust reservoir whose dust emission capacity depends on the type of vegetation and cover. The dust reservoirs are divided into reservoirs with stable and unstable surface. The changes of emission in time depend on meteorological parameters.The wind blown dust emission should be treated as a non-continuous spatio-temporal process. The emissions are estimated with high uncertainty. The estimated PM₁₀ yearly total load emitted by wind from the European territory is highly differentiated in space and time and is equal to 0.74 Tg. The total load of PM₁₀ emitted by wind from North African and Southwest Asian land surface located in the vicinity of European boundaries is assessed as nearly 50% (0.43 Tg) of the total load estimated for the whole Europe.The average yearly PM₁₀ emission factor for Europe was estimated at 0.139 Mg km^?2.The PM₁₀ emission from agricultural areas is estimated at 52% of the total wind blown emission from the domain of the European Union project “Improving and applying methods for the calculation of natural and biogenic emissions and assessment of impacts to the air quality” - NatAir.PM₁₀ emission factor for natural areas of Europe is estimated at 0.021 Mg km^?2. Appropriate factors for agricultural areas and anthropogenic areas are 0.157 Mg km^?2 and 0.118 Mg km^?2, respectively. The latter two factors are probably underestimated due to omitting in the model of other dust emission mechanisms than aeolian erosion.     

A study of the total atmospheric sulfur dioxide load using ground-based measurements and the satellite derived Sulfur Dioxide Index

We present characteristics of the sulfur dioxide (SO₂) loading over Thessaloniki, Greece, and seven other selected sites around the world using SO₂ total column measurements from Brewer spectrophotometers together with satellite estimates of the Version 8 TOMS Sulfur Dioxide Index (SOI) over the same locations, retrieved from Nimbus 7 TOMS (1979–1993), Earth Probe TOMS (1996–2003) and OMI/Aura (2004–2006). Traditionally, the SOI has been used to quantify the SO₂ quantities emitted during great volcanic eruptions. Here, we investigate whether the SOI can give an indication of the total SO₂ load for areas and periods away from eruptive volcanic activity by studying its relative changes as a correlative measure to the SO₂ total column. We examined time series from Thessaloniki and another seven urban and non-urban stations, five in the European Union (Arosa, De Bilt, Hohenpeissenberg, Madrid, Rome) and two in India (Kodaikanal, New Delhi). Based on the Brewer data, Thessaloniki shows high SO₂ total columns for a European Union city but values are still low if compared to highly affected regions like those in India. For the time period 1983–2006 the SO₂ levels above Thessaloniki have generally decreased with a rate of 0.028 Dobson Units (DU) per annum, presumably due to the European Union's strict sulfur control policies. The seasonal variability of the SO₂ total column exhibits a double peak structure with two maxima, one during winter and the second during summer. The winter peak can be attributed to central heating while the summer peak is due to synoptic transport from sources west of the city and sources in the north of Greece. A moderate correlation was found between the seasonal levels of Brewer total SO₂ and SOI for Thessaloniki, Greece (R = 0.710–0.763) and Madrid, Spain (R = 0.691) which shows that under specific conditions the SOI might act as an indicator of the SO₂ total load.