A tropical rainforest clearing experiment by biomass burning in the state of Pará, Brazil

Results are described of a forest clearing experiment conducted in Tomé Acu, located approximately 250 km south of Belém, the capital of the Brazilian northern state of Pará. An area of 3 ha of virgin forest was cut in July 1994 and left to dry until October of the same year, when fire was set. Post burning was also performed 30 days after the main fire. The test location biomass content per hectare was measured by indirect methods using formulas with parameters of forest inventories. The carbon content of the several biomass compartments was determined in a CHN analyzer. The combustion completeness was estimated by selecting ten 2+2 m² areas and 24 large trunks and examining their consumption rates by fire. The 2+2 m² areas were used to determine the completeness of small parts of biomass (those whose characteristic diameters were lower than 10 cm) and the trunks to determine the efficiency of the larger parts (characteristic diameters larger than 10 cm). The overall process combustion completeness was estimated to be 20.1%. Considering that the combustion gases of carbon in open fires contain approximately 90% of CO₂ and 10% of CO in volumetric basis, the emission rates of these gases by the burning process were estimated as 70.2 and 5.0 t ha^-1, respectively.     

Inventory of aerosol and sulphur dioxide emissions from India. Part II—biomass combustion

A spatially resolved biomass burning data set, and related emissions of sulphur dioxide and aerosol chemical constituents was constructed for India, for 1996–1997 and extrapolated to the INDOEX period (1998–1999). Sources include biofuels (wood, crop waste and dung-cake) and forest fires (accidental, shifting cultivation and controlled burning). Particulate matter (PM) emission factors were compiled from studies of Indian cooking stoves and from literature for open burning. Black carbon (BC) and organic matter (OM) emissions were estimated from these, accounting for combustion temperatures in cooking stoves. Sulphur dioxide emission factors were based on fuel sulphur content and reported literature measurements. Biofuels accounted 93% of total biomass consumption (577 MT yr⁻¹), with forest fires contributing only 7%. The national average biofuel mix was 56 : 21 : 23% of fuelwood, crop waste and dung-cake, respectively. Compared to fossil fuels, biomass combustion was a minor source of SO₂ (7% of total), with higher emissions from dung-cake because of its higher sulphur content. PM_2.5 emissions of 2.04 Tg yr⁻¹ with an “inorganic fraction” of 0.86 Tg yr⁻¹ were estimated. Biomass combustion was the major source of carbonaceous aerosols, accounting 0.25 Tg yr⁻¹ of BC (72% of total) and 0.94 Tg yr⁻¹ of OM (76% of total). Among biomass, fuelwood and crop waste were primary contributors to BC emissions, while dung-cake and forest fires were primary contributors to OM emissions. Northern and the east-coast India had high densities of biomass consumption and related emissions. Measurements of emission factors of SO₂, size resolved aerosols and their chemical constituents for Indian cooking stoves are needed to refine the present estimates.     

Fire and biofuel contributions to annual mean aerosol mass concentrations in the United States

We estimate the contributions from biomass burning (summer wildfires, other fires, residential biofuel, and industrial biofuel) to seasonal and annual aerosol concentrations in the United States. Our approach is to use total carbonaceous (TC) and non-soil potassium (ns-K) aerosol mass concentrations for 2001–2004 from the nationwide IMPROVE network of surface sites, together with satellite fire data. We find that summer wildfires largely drive the observed interannual variability of TC aerosol concentrations in the United States. TC/ns-K mass enhancement ratios from fires range from 10 for grassland and shrub fires in the south to 130 for forest fires in the north. The resulting summer wildfire contributions to annual TC aerosol concentrations for 2001–2004 are 0.26 μg C m⁻³ in the west and 0.14 μg C m⁻³ in the east; Canadian fires are a major contributor in the east. Non-summer wildfires and prescribed burns contribute on an annual mean basis 0.27 and 0.31 μg C m⁻³ in the west and the east, highest in the southeast because of prescribed burning. Residential biofuel is a large contributor in the northeast with annual mean concentration of up to 2.2 μg C m⁻³ in Maine. Industrial biofuel (mainly paper and pulp mills) contributes up to 0.3 μg C m⁻³ in the southeast. Total annual mean fine aerosol concentrations from biomass burning average 1.2 and 1.6 μg m⁻³ in the west and east, respectively, contributing about 50% of observed annual mean TC concentrations in both regions and accounting for 30% (west) and 20% (east) of total observed fine aerosol concentrations. Our analysis supports bottom-up source estimates for the contiguous United States of 0.7–0.9 Tg C yr⁻¹ from open fires (climatological) and 0.4 Tg C yr⁻¹ from biofuel use. Biomass burning is thus an important contributor to US air quality degradation, which is likely to grow in the future.     

Emission factors of PAHs,methoxyphenols, levoglucosan,elemental carbon and organic carbon from simulated wheat and Kentucky bluegrass stubble burns

Emission factors (EFs) of pollutants from post-harvest agricultural burning are required for predicting downwind impacts of smoke and inventorying emissions. EFs of polycyclic aromatic hydrocarbons (PAH), methoxyphenols (MP), levoglucosan (LG), elemental carbon (EC) and organic carbon (OC) from wheat and Kentucky bluegrass (KBG) stubble burning were quantified in a US EPA test burn facility. The PAH and MP EFs for combined solid+gas phases are 17±8.2 mg kg⁻¹ and 79±36 mg kg⁻¹, respectively, for wheat and 21±15 mg kg⁻¹ and 35±24 mg kg⁻¹, respectively, for KBG. LG, particulate EC and artifact-corrected OC EFs are 150±130 mg kg⁻¹, 0.35±0.16 g kg⁻¹ and 1.9±1.1 g kg⁻¹, respectively, for wheat and 350±510 mg kg⁻¹, 0.63±0.056 g kg⁻¹ and 6.9±0.85 g kg⁻¹, respectively, for KBG. Positive artifacts associated with OC sampling were evaluated and remedied with a two-filter system. EC and OC accounted for almost two-thirds of PM_2.5 mass, while LG accounted for just under 3% of the PM_2.5 mass. Since EFs of these pollutants generally decreased with increasing combustion efficiency (CE), identifying and implementing methods of increasing the CEs of burns would help reduce their emissions from agricultural field burning. PAH, OC and EC EFs are comparable to other similar studies reported in literature. MP EFs appear dependent on the stubble type and are lower than the EFs for hard and softwoods reported in literature, possibly due to the lower lignin content in wheat and KBG.     

Mercury deposition through litterfall in an Atlantic Forest at Ilha Grande,Southeast Brazil

Atmospheric Hg transfer to the forest soil through litterfall was investigated in a primary rainforest at Ilha Grande (Southeast Brazil) from January to December 1997. Litter mass deposition reached 10.0 t ha⁻¹ y⁻¹, with leaves composing 50–84% of the total litter mass. Concentrations of Hg in the total fallen litter varied from 20 to 244 ng g⁻¹, with higher concentrations during the dry season, between June and August (225 ± 17 ng g⁻¹), and lower concentrations during the rainy season (99 ± 54 ng g⁻¹). This seasonal variability was reflected in the Hg flux through litterfall, which corresponded to a Hg input to the forest floor of 122 μg m⁻² y⁻¹, with average Hg deposition of 16.5 ± 1.5 μg m⁻² month⁻¹ during and just after the dry season (June–September) and 7.0 ± 3.6 μg m⁻² month⁻¹ in the rest of the year. The variability in meteorological conditions (determining atmospheric Hg availability to foliar scavenging) may explain the pulsed pattern of Hg deposition, since litterfall temporal variability was generally unrelated with such deposition, except by a peak in litterfall production in September. Comparisons with regional data on Hg atmospheric deposition show that litterfall promotes Hg deposition at Ilha Grande two to three orders of magnitude higher than open rainfall deposition in non-industrialized areas and approximately two times higher than open rainfall deposition in industrialized areas in Rio de Janeiro State. The observed input suggests that atmospheric Hg transfer through litterfall may explain a larger fraction of the total Hg input to forest soils in Southeast Brazil than those recorded at higher latitudes.     

Inorganic,organic and macromolecular components of fine aerosol in different areas of Europe in relation to their water solubility

A chemical mass balance of fine aerosol (<1.5 μm AED) collected at three European sites was performed with reference to the water solubility of the different aerosol classes of components. The sampling sites are characterised by different pollution conditions and aerosol loading in the air. Aspvreten is a background site in central Sweden, K-puszta is a rural site in the Great Hungarian Plain and San Pietro Capofiume is located in the polluted Po Valley, northern Italy. The average fine aerosol mass concentration was 5.9 μg m^-3 at the background site Aspvreten, 24 μg m^-3 at the rural K-puszta and 38 μg m^-3 at the polluted site San Pietro Capofiume. However, a similarly high soluble fraction of the aerosol (65–75%) was measured at the three sites, while the percentage of water soluble organic species with respect to the total soluble mass was much higher at the background site (ca. 50%) than at the other two sites (ca. 25%). A very high fraction (over 70%) of organic compounds in the aerosol consisted of polar species. The presence of water soluble macromolecular compounds was revealed in the samples from K-puszta and San Pietro Capofiume. At both sites these species accounted for between ca. 20–50% of the water soluble organic fraction. The origin of the compounds was tentatively attributed to biomass combustion.     

Air concentrations and wet deposition of major inorganic ions at five non-urban sites in China, 2001–2003

Air and precipitation measurements at five sites were undertaken from 2001 to 2003 in four different provinces in China, as part of the acid rain monitoring program IMPACTS. The sites were located in Tie Shan Ping (TSP) in Chongqing, Cai Jia Tang (CJT) in Hunan, Lei Gong Shan (LGS) and Liu Chong Guan (LCG) in Guizhou and Li Xi He (LXH) in Guangdong. The site characteristics are quite varied with TSP and LCG located relatively near big cites while the three others are situated in more regionally representative areas. The distances to urban centres are reflected in the air pollution concentrations, with annual average concentrations of SO₂ ranging from 0.5 to above 40 μg S m⁻³. The main components in the airborne particles are (NH₄)₂SO₄ and CaSO₄. Reduced nitrogen has a considerably higher concentration level than oxidised nitrogen, reflecting the high ammonia emissions from agriculture. The gas/particle ratio for the nitrogen compounds is about 1:1 at all the three intensive measurement sites, while for sulphur it varies from 2.5 to 0.5 depending on the distance to the emission sources. As in air, the predominant ions in precipitation are sulphate, calcium and ammonium. The volume weighted annual concentration of sulphate ranges from about 70 μeq l⁻¹ at the most rural site (LGS) to about 200 μeq l⁻¹ at TSP and LCG. The calcium concentration ranges from 25 to 250 μeq l⁻¹, while the total nitrogen concentration is between 30 and 150 μeq l⁻¹; ammonium is generally twice as high as nitrate. China's acid rain research has traditionally been focused on urban sites, but these measurements show a significant influence of long range transported air pollutants to rural areas in China. The concentration levels are significantly higher than seen in most other parts of the world.     

Atmospheric bulk deposition of dioxin and furans to Danish background areas

Polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) were measured in bulk deposition at three Danish rural forest sites with a mutual maximum distance of 450 km. At one of the forest sites concentrations in the ambient atmosphere were sampled from a 12 m high tower. Sampling was carried out within a period of 3 years with sampling intervals of 1–2 months. Mean bulk deposition fluxes were 1 ng m⁻² yr⁻¹ I-TEQ and deviated less than 30% between the sites. Yearly average PCDD/F concentrations in the atmosphere were 24 fg m⁻³ I-TEQ with maximum values in the winter period. During winter months atmospheric concentrations of PCDD/F and oxidized sulphur compounds showed a positive correlation, furthermore seasonal bulk deposition showed correlation between PCDD/F and sulphate.     

Inventory of aerosol and sulphur dioxide emissions from India: I—Fossil fuel combustion

A comprehensive, spatially resolved (0.25°×0.25°) fossil fuel consumption database and emissions inventory was constructed, for India, for the first time. Emissions of sulphur dioxide and aerosol chemical constituents were estimated for 1996–1997 and extrapolated to the Indian Ocean Experiment (INDOEX) study period (1998–1999). District level consumption of coal/lignite, petroleum and natural gas in power plants, industrial, transportation and domestic sectors was 9411 PJ, with major contributions from coal (54%) followed by diesel (18%). Emission factors for various pollutants were derived using India specific fuel characteristics and information on combustion/air pollution control technologies for the power and industrial sectors. Domestic and transportation emission factors, appropriate for Indian source characteristics, were compiled from literature. SO₂ emissions from fossil fuel combustion for 1996–1997 were 4.0 Tg SO₂ yr⁻¹, with 756 large point sources (e.g. utilities, iron and steel, fertilisers, cement, refineries and petrochemicals and non-ferrous metals), accounting for 62%. PM_2.5 emitted was 0.5 and 2.0 Tg yr⁻¹ for the 100% and the 50% control scenario, respectively, applied to coal burning in the power and industrial sectors. Coal combustion was the major source of PM_2.5 (92%) primarily consisting of fly ash, accounting for 98% of the “inorganic fraction” emissions (difference between PM_2.5 and black carbon+organic matter) of 1.6 Tg yr⁻¹. Black carbon emissions were estimated at 0.1 Tg yr⁻¹, with 58% from diesel transport, and organic matter emissions at 0.3 Tg yr⁻¹, with 48% from brick-kilns. Fossil fuel consumption and emissions peaked at the large point industrial sources and 22 cities, with elevated area fluxes in northern and western India. The spatial resolution of this inventory makes it suitable for regional-scale aerosol-climate studies. These results are compared to previous studies and differences discussed. Measurements of emission factors for Indian sources are needed to further refine these estimates.     

Identification,abundance and seasonal variation of anthropogenic organic aerosols from a mega-city in China

PM_2.5 aerosols were collected in Nanjing, a typical mega-city in China, during summer and winter 2004 and were characterized for aromatic and cyclic compounds using a GC/MS technique to understand the air pollution problem. They include polycyclic aromatic hydrocarbons (PAHs), hopanes, phthalates and hydroxy-PAHs (OH-PAHs). PAHs, hopanes and OH-PAHs presented higher concentrations in winter (26–178, 3.0–18, and 0.013–0.421 ng m⁻³, respectively) than in summer (12–96, 1.6–11, and 0.029–0.171 ng m⁻³, respectively) due to an enhanced coal burning for house heating and atmospheric inversion layers developed in the cold season. In contrast, phthalates are more abundant in summer (109–368 ng m⁻³, average 230 ng m⁻³) than in winter (33–390 ng m⁻³, average 170 ng m⁻³) due to an enhanced evaporation from plastics during the hot season and the subsequent deposition on the pre-existing particles. Generally, all the identified compounds showed higher concentrations in nighttime than in daytime due to inversion layers and increased emissions from heavy-duty trucks at night. PAHs, hopanes and phthalates in Nanjing aerosols are 5–100 times more abundant than those in Los Angeles, USA, indicating a serious air pollution problem in the city. Concentrations of OH-PAHs are 1–3 orders of magnitude less than their parent PAHs and comparable to those reported from other international cities. Source identification using diagnostic ratios of the organic tracers suggests that PAHs in Nanjing urban area are mainly derived from coal burning, whereas hopanes are more attributable to traffic emissions.     

The use of receptor modelling and emission inventory data to explain the downward trend in UK PM10 concentrations

Statistically significant downward trends in measured UK annual mean PM₁₀ concentrations have been observed at eight out of the nine urban background monitoring sites between the start of monitoring in 1992 or 1993 and 2000.Site-specific projections of the individual components of measured PM₁₀ concentrations have been derived for the period 1992–2000 at three monitoring sites from receptor modelling results for 1999 monitoring data. Measured annual average PM₁₀ concentrations declined to between 71% and 66% of the 1992 values during this period at the sites studied. The largest contributions to the decline in total PM₁₀ are from secondary particles at London Bloomsbury (40%, 3.4 μg m⁻³, tapered element oscillating microbalance (TEOM)), stationary sources at Belfast Centre (53%, 4.6 μg m⁻³, TEOM) and roadside traffic emissions at Bury Roadside (49%, 5.0 μg m⁻³, TEOM). The good agreement between the projected total PM₁₀ concentrations and measured values for the years 1992–2000 indicate that the combination of the receptor model and the site-specific projections provide a suitably robust method for predicting future PM₁₀ concentrations and the quantification of the impact of possible future policy measures to reduce PM₁₀ concentrations. The good agreement between the projections and measured concentration also provides a useful verification of the trends in emissions inventory estimates for the 1990s.Projections of estimated PM₁₀ concentrations have also been calculated for the London Bloomsbury site for the period from 1970 to 1991. Annual mean concentrations are predicted to have been in the range from 30 to 35 μg m⁻³, TEOM from 1977 to 1991 but much higher at values between 39 and 46 μg m⁻³, TEOM in the early 1970s.     

Deposition and adsorption of the air pollutant HNO3 vapor to soil surfaces

Deposition of nitric acid (HNO₃) vapor to soils has been evaluated in three experimental settings: (1) continuously stirred tank reactors with the pollutant added to clean air, (2) open-top chambers at high ambient levels of pollution with and without filtration reducing particulate nitrate levels, (3) two field sites with high or low pollution loads in the coastal sage plant community of southern California. The results from experiment (1) indicated that the amount of extractable NO₃⁻ from isolated sand, silt and clay fractions increased with atmospheric concentration and duration of exposure. After 32 days, the highest absorption of HNO₃ was determined for clay, followed by silt and sand. While the sand and silt fractions showed a tendency to saturate, the clay samples did not after 32 days of exposure under highly polluted conditions. Absorption of HNO₃ occurred mainly in the top 1 mm layer of the soil samples and the presence of water increased HNO₃ absorption by about 2-fold. Experiment (2) indicated that the presence of coarse particulate NO₃⁻ could effectively block absorption sites of soils for HNO₃ vapor. Experiment (3) showed that soil samples collected from open sites had about 2.5 more extractable NO₃⁻ as compared to samples collected from beneath shrub canopies. The difference in NO₃⁻ occurred only in the upper 1–2 cm as no significant differences in NO₃⁻ concentrations were found in the 2–5 cm soil layers. Extractable NO₃⁻ from surface soils collected from a low-pollution site ranged between 1 and 8 μg NO₃–N g⁻¹, compared to a maximum of 42 μg NO₃–N g⁻¹ for soils collected from a highly polluted site. Highly significant relationship between HNO₃ vapor doses and its accumulation in the upper layers of soils indicates that carefully prepared soil samples (especially clay fraction) may be useful as passive samplers for evaluation of ambient concentrations of HNO₃ vapor.     

Laboratory studies on the uptake of aromatic hydrocarbons by ice crystals during vapor depositional crystal growth

Uptake of aromatic hydrocarbons (AH) by ice crystals during vapor deposit growth was investigated in a walk-in cold chamber at temperatures of 242, 251, and 260 K, respectively. Ice crystals were grown from ambient air in the presence of gaseous AH namely: benzene (C₆H₆), toluene (methylbenzene, C₇H₈), the C₈H₁₀ isomers ethylbenzene, o-, m-, p-xylene (dimethylbenzenes), the C₉H₁₂ isomers n-propylbenzene, 4-ethyltoluene, 1,3,5-trimethylbenzene (1,3,5-TMB), 1,2,4-trimethylbenzene (1,2,4-TMB), 1,2,3-trimethylbenzene (1,2,3-TMB), and the C₁₀H₁₄ compound tert.-butylbenzene. Gas-phase concentrations calculated at 295 K were 10.3–20.8 μg m⁻³. Uptake of AH was detected by analyzing vapor deposited ice with a very sensitive method composed of solid-phase micro-extraction (SPME), followed by gas chromatography/mass spectrometry (GC/MS).Ice crystal size was lower than 1 cm. At water vapor extents of 5.8, 6.0 and 8.1 g m⁻³, ice crystal shape changed with decreasing temperatures from a column at a temperature of 260 K, to a plate at 251 K, and to a dendrite at 242 K. Experimentally observed ice growth rates were between 3.3 and 13.3×10⁻³ g s⁻¹ m⁻² and decreased at lower temperatures and lower value of water vapor concentration. Predicted growth rates were mostly slightly higher.Benzene, toluene, ethylbenzene, and xylenes (BTEX) were not detected in ice above their detection limits (DLs) of 25 pg g_ice⁻¹ (toluene, ethylbenzene, xylenes) and 125 pg g_ice⁻¹ (benzene) over the entire temperature range. Median concentrations of n-propylbenzene, 4-ethyltoluene, 1,3,5-TMB, tert.-butylbenzene, 1,2,4-TMB, and 1,2,3-TMB were between 4 and 176 pg g_ice⁻¹ at gas concentrations of 10.3–10.7 μg m⁻³ calculated at 295 K. Uptake coefficients (K) defined as the product of concentration of AH in ice and density of ice related to the product of their concentration in the gas phase and ice mass varied between 0.40 and 10.23. K increased with decreasing temperatures. Values of Gibbs energy (ΔG) were between −4.5 and 2.4 kJ mol⁻¹ and decreased as temperatures were lowered. From the uptake experiments, the uptake enthalpy (ΔH) could be determined between −70.6 and −33.9 kJ mol⁻¹. The uptake entropy (ΔS) was between −281.3 and −126.8 J mol⁻¹ K⁻¹. Values of ΔH and ΔS were rather similar for 4-ethlytoluene, 1,3,5-TMB and tert.-butylbenzene, whereas 1,2,3-TMB showed much higher values.     

Comparative analysis of organic and elemental carbon concentrations in carbonaceous aerosols in three European cities

Sampling and analysis of carbonaceous compounds in particulate matter presents a number of difficulties related to artefacts during sampling and to the distinction between organic (OC) and elemental carbon (EC) during analysis. Our study reports on a comparative analysis of OC, EC and WSOC (water-soluble organic carbon) concentrations, as well as sampling artefacts, for PM2.5 aerosol in three European cities (Amsterdam, Barcelona and Ghent) representing Southern and Western European urban environments. Comparability of results was ensured by using a single system for sample analysis from the different sites. OC and EC concentrations were higher in the vicinity of roads, thus having higher levels in Amsterdam (3.9–6.7 and 1.7–1.9 μg m⁻³, respectively) and Barcelona (3.6–6.9 and 1.5–2.6 μg m⁻³) than in Ghent (2.7–5.4 and 0.8–1.2 μg m⁻³). A relatively larger influence of secondary organic aerosols (SOA), as deduced from a larger OC/EC ratio, was observed in Ghent. In absolute sense, WSOC concentrations were similar at the three sites (1.0–2.3 μg m⁻³). Positive artefacts were higher in Southern (11–16% of the OC concentration in Barcelona) than in Western Europe (5–12% in Amsterdam, 5–7% in Ghent). During special episodes, the contribution of carbonaceous aerosols from non-local sources accounted for 67–69% of the OC concentration in Western Europe, and for 44% in Southern Europe.     

Characterization of PM2.5-bound polycyclic aromatic hydrocarbons in Atlanta

Twenty-four hour PM_2.5 samples from a rural site, an urban site, and a suburban site (next to a major highway) in the metropolitan Atlanta area in December 2003 and June 2004 were analyzed for 19 polycyclic aromatic hydrocarbons (PAH). Extraction of the air samples was conducted using an accelerated solvent extraction method followed by isotope dilution gas chromatography/mass spectrometry determination. Distinct seasonal variations were observed in total PAH concentration (i.e. significantly higher concentrations in December than in June). Mean concentrations for total particulate PAHs in December were 3.16, 4.13, and 3.40 ng m^?3 for the urban, suburban and rural sites, respectively, compared with 0.60, 0.74, and 0.24 ng m^?3 in June. Overall, the suburban site, which is impacted by a nearby major highway, had higher PAH concentration than did the urban site. Total PAH concentrations were found to be well correlated with PM_2.5, organic carbon (OC), and elemental carbon (EC) in both months (r² = 0.36–0.78, p < 0.05), although the slopes from the two months were different. PAHs represented on average 0.006% of total PM_2.5 mass and 0.017% of OC in June, compared with 0.033% of total PM_2.5 and 0.14% of OC in December. Total PAH concentrations were also correlated with potassium ion (r² = 0.39, p = 0.014) in December, but not in June, suggesting that in winter biomass burning can potentially be an important source for particulate PAH. Retene was found at a higher median air concentration at the rural site than at the urban and suburban sites—unlike the rest of the PAHs, which were found at lower levels at the rural site. Retene also had a larger seasonal difference and had the weakest correlation with the rest of the PAHs measured, suggesting that retene, in particular, might be associated with biomass burning.     

Atmospheric distribution of polycyclic aromatic hydrocarbons and deposition to Galveston Bay,Texas, USA

Estimates of the atmospheric deposition to Galveston Bay of polycyclic aromatic hydrocarbons (PAHs) are made using precipitation and meteorological data that were collected continuously from 2 February 1995 to 6 August 1996 at Seabrook, TX, USA. Particulate and vapor phase PAHs in ambient air and particulate and dissolved phases in rain samples were collected and analyzed. More than 95% of atmospheric PAHs were in the vapor phase and about 73% of PAHs in the rain were in the dissolved phase. Phenanthrene and napthalene were the dominant compounds in air vapor and rain dissolved phases, respectively, while 5 and 6 ring PAH were predominant in the particulate phase of both air and rain samples. Total PAH concentrations ranged from 4 to 161 ng m⁻³ in air samples and from 50 to 312 ng l⁻¹ in rain samples. Temporal variability in total PAH air concentrations were observed, with lower concentrations in the spring and fall (4–34 ng m ⁻³) compared to the summer and winter (37–161 ng m⁻³). PAHs in the air near Galveston Bay are derived from both combustion and petroleum vaporization. Gas exchange from the atmosphere to the surface water is estimated to be the major deposition process for PAHs (1211 μg m^{− 2} yr^{− 1}), relative to wet deposition (130 μg m⁻² yr^{− 1}) and dry deposition (99 μg m⁻² yr^{− 1}). Annual deposition of PAHs directly to Galveston Bay from the atmosphere is estimated as 2  t yr⁻¹.     

Characterization of emissions from portable household combustion devices: particle size distributions,emission rates and factors,and potential exposures

A series of source tests were conducted to characterize emissions of particulate matter (PM), carbon monoxide (CO), carbon dioxide (CO₂), methane (CH₄), and total hydrocarbon (THC ) from five types of portable combustion devices. Tested combustion devices included a kerosene lamp, an oil lamp, a kerosene space heater, a portable gas range, and four unscented candles. All tests were conducted either in a well-mixed chamber or a well-mixed room, which enables us to determine emission rates and emission factors using a single-compartment mass balance model. Particle mass concentrations and number concentrations were measured using a nephelometric particle monitor and an eight-channel optical particle counter, respectively. Real-time CO concentrations were measured with an electrochemical sensor CO monitor. CO₂, CH₄, and THC were measured using a GC-FID technique. The results indicate that all particles emitted during steady burning in each of the tested devices were smaller than 1.0 μm in diameter with the vast majority in the range between 0.1 and 0.3 μm. The PM mass emission rates and emission factors for the tested devices ranged from 5.6±0.1 to 142.3±40.8 mg h⁻¹ and from 0.35±0.06 to 9.04±4.0 mg g⁻¹, respectively. The CO emission rates and emission factors ranged from 4.7±3.0 to 226.7±100 mg h⁻¹ and from 0.25±0.12 to 1.56±0.7 mg g⁻¹, respectively. The CO₂ emission rates and emission factors ranged from 5500±700 to 210,000±90,000 mg h⁻¹ and from 387±45 to 1689±640 mg g⁻¹, respectively. The contributions of CH₄ and THC to emission inventories are expected to be insignificant due both to the small emission factors and to the relatively small quantity of fuel consumed by these portable devices. An exposure scenario analysis indicates that every-day use of the kerosene lamp in a village house can generate fine PM exposures easily exceeding the US promulgated NAAQS for PM_2.5.     

Contribution of railway traffic to local PM10 concentrations in Switzerland

Field measurement campaigns of PM10 and its elemental composition (daily sampling on filters) covering different seasons were performed at two sites near the busiest railway station of Switzerland in Zurich (at a distance of 10 m from the tracks) and at a site near a very busy railway line with more than 700 trains per day. At this latter site parallel samples were taken at 10, 36 and 120 m distances from the tracks with the aim to study the distance dependence of the railway induced PM10 concentrations.To distinguish the relatively small railway emissions from the regional background (typically 20–25 μg m⁻³), simultaneous samples were also taken at an urban background site in Zurich. The differences in PM10 and elemental concentrations between the railway exposed sites and the background site were allocated to the railway contribution.Small, however, measurable PM10 concentration differences were found at all sites. The elemental composition of these differences revealed iron as the only quantitatively important constituent. As a long-term average it amounted to approximately 1 μg m⁻³ Fe at a distance of 10 m from the tracks at all three sites. Assuming that iron was at least partly oxidised (e.g. in the form of Fe₂O₃) the contribution can amount up to 1.5 μg m⁻³. Emissions of copper, manganese and chromium from trains were also clearly identified. However, compared to iron these, elements were emitted in very low quantities.No significant contribution from rock material (calcium, aluminium, magnesium, sodium) was observed as might have been expected from erosion, abrasion and resuspension from the gravel below the tracks. Particle emissions from diesel exhaust were not considered as trains in Switzerland are operated nearly exclusively by electric locomotives.The railway, induced contribution to ambient PM10 decreased rapidly with increasing distance from the tracks. At a distance of 120 m this contribution dropped to only 25% of the contribution observed at 10 m distance.     

Ambient air quality of two metropolitan cities of Pakistan and its health implications

The present study reports findings on TSP loading in the ambient air of two major cities in Pakistan – Karachi and Islamabad. Data for TSP were collected at one site in Karachi and two in Islamabad between 10 December 1998 and 08 January 1999. This article reports one of the highest TSP loadings recorded so far in any megacity of the world. During the study period, average daily TSP concentrations at the Karachi site ranged from 627 to 938 μg m⁻³ with a mean of 668 μg m⁻³. On four occasions TSP concentrations were >1000 μg m⁻³ (range 1031–1736 μg m⁻³). At the Islamabad sampling site in close proximity to the city's industrial sector, daily TSP concentrations varied in the range of 428–998 μg m⁻³ (mean 691 μg m⁻³). Even at a relatively remote site of the city (Saidpur), TSP loading was high (range 145–448 μg m⁻³; mean 275 μg m⁻³). By virtue of the WHO definition, the 24-h average TSP concentrations in a busy commercial site in Karachi and in the vicinity of an industrial sector in Islamabad were in “exceedance” by a factor of 4–8. At Saidpur, the remote site, the 24-h average TSP loading exceeded the WHO guideline of 120 μg m⁻³ by a factor of 1.2–3.7.     

Properties of organic matter in PM2.5 at Changdao Island,China—A rural site in the transport path of the Asian continental outflow

Fifty-five seasonal PM_2.5 samples were collected March 2003–January 2004 at Changdao, a resort island located at the demarcation line between Bohai Sea and Yellow Sea in Northern China. Changdao is in the transport path of the continental aerosols heading toward the Pacific Ocean in winter and spring due to the East Asia Monsoon. Solvent-extractable organic compounds (SEOC), organic carbon (OC), elemental carbon (EC) and water-soluble organic carbon (WSOC) were analyzed for source identification based on molecular markers. This data set provides useful information for the downstream site researchers of the Asian continental outflow. Total carbon (TC, OC+EC) was ∼18 μg m⁻³ in winter, ∼9 μg m⁻³ in spring and autumn and a large part of the TC was WSOC (33% in winter, >45% in the other seasons). Winter and spring were the high SEOC seasons with n-fatty acids the highest at ∼290 and ∼170 ng m⁻³, respectively, followed by n-alkanes at ∼210 and ∼90 ng m⁻³, and polycyclic aromatic hydrocarbons (PAHs) were also at high at ∼120 and ∼30 ng m⁻³. High WSOC/TC, low C_18:1/C₁₈ of fatty acids, and low concentrations of labile PAHs such as benzo(a)pyrene, together with back trajectory analysis suggested that the aerosols were aged and transported. PAHs, triterpane and sterane distributions provided evidence that coal burning was the main source of the continental outflow. The detection of levoglucosan and β-sitosterol in nearly all the samples showed the impact of biomass burning.