Quantifying the effect of urban tree planting on concentrations and depositions of PM10 in two UK conurbations

Trees are efficient scavengers of particulate matter and are characterised by higher rates of dry deposition than other land types. To estimate the potential of urban tree planting for the mitigation of urban PM₁₀ concentrations, an atmospheric transport model was used to simulate the transport and deposition of PM₁₀ across two UK conurbations (the West Midlands and Glasgow). Tree planting was simulated by modifying the land cover database, using GIS techniques and field surveys to estimate reasonable planting potentials. The model predicts that increasing total tree cover in West Midlands from 3.7% to 16.5% reduces average primary PM₁₀ concentrations by 10% from 2.3 to 2.1 μg m⁻³ removing 110 ton per year of primary PM₁₀ from the atmosphere. Increasing tree cover of the West Midlands to a theoretical maximum of 54% by planting all available green space would reduce the average PM₁₀ concentration by 26%, removing 200 ton of primary PM₁₀ per year. Similarly, for Glasgow, increasing tree cover from 3.6% to 8% reduces primary PM₁₀ concentrations by 2%, removing 4 ton of primary PM₁₀ per year. Increasing tree cover to 21% would reduce primary PM₁₀ air concentrations by 7%, removing 13 ton of primary PM₁₀ per year.     

Commuter exposure to particulate matter in public transportation modes in Hong Kong

This study examined commuter’s exposure to respirable suspended particulate matters while commuting in public transportation modes. The survey was conducted between October 1999 and January 2000 in Hong Kong. A total of eight public transportation modes, that are bus, tram, public light bus, taxi, ferry, Kowloon–Canton Railway, Mass Transit Railway and Light Rail Transit, were selected in the study. They were grouped into four categories: (T1) railway transport; (T2) non-air-conditioned roadway transport; (T3) air-conditioned roadway transport and (T4) marine transport. Both PM₁₀ and PM_2.5 levels were investigated. The results indicate that the particulate level is greatly affected by the mode of transport as well as the ventilation system of the transport. The overall average PM₁₀ concentration level in T2 (147 μg m⁻³) is the highest and is followed by T4 (81 μg m⁻³) and T3 (65 μg m⁻³). The PM₁₀ level in T1 (50 μg m⁻³) is the lowest. Notably, the commuter exposure in tram (175 μg m⁻³) is the highest among all the monitored commuting modes. Commuting modes such as railway and air-conditioned vehicle are recommended as a substitute for non-air-conditioned vehicle. The PM_2.5 to PM₁₀ ratio in transports ranged from 63% to 78%. Higher PM_2.5 to PM₁₀ ratio is found in vehicles with air-conditioning system. For the double deck vehicle, higher PM₁₀ level has resulted in the lower deck. The average upper-deck to lower-deck PM₁₀ ratio is 0.836, 0.751 and 0.738 in air-conditioned bus, non-air-conditioned bus and non-air-conditioned tram, respectively. Typical concentration profiles in different transports are also presented.     

Assessment of road users’ elemental carbon personal exposure levels,London, UK

Little is known about particulate elemental carbon (EC) personal exposure levels, a key component of diesel exhaust, specifically in transport microenvironments. A method utilizing the optical properties of EC particles has been applied to personal exposure measurement filter samples. In a series of field studies carried out in London, UK, during 1999–2000 over 400 fine particle (PM_2.5) personal exposure level measurements were taken for journeys in bicycle, bus, car and underground rail transport microenvironments, along three main fixed routes. The particulate EC contribution to the PM_2.5 personal exposure was assessed indirectly by means of an optical technique and with the development and use of a size fraction specific and site-specific calibration curve. In this first EC personal exposure study of transport users geometric mean exposure levels in the summer field campaign were 11.2 μg m⁻³ (GSD=2.7) for cyclists, 13.6 μg m⁻³ (GSD=1.9) for bus passengers and 21.6 μg m⁻³ (GSD=2.1) for car drivers; corresponding exposure levels in the winter were 16.4 μg m⁻³ (GSD=1.8), 18.6 μg m⁻³ (GSD=2.3) and 27.3 μg m⁻³ (GSD=2.0), respectively. EC/PM_2.5 ratios were approximately 0.5–0.6 for bicycle and bus modes and 0.7–0.8 for the car mode. EC/PM_2.5 ratios for different routes ranged from approximately 0.7 for Route 1 to 0.4 for Route 3. Cyclists had the lowest exposure to EC, and car occupants the highest exposure. A large difference in exposure levels between a central high traffic density route and the other less central routes was observed. Particulate EC was a very significant proportion of the total PM_2.5 personal exposure and EC personal exposure levels were considerably higher than reported fixed site monitor EC concentrations.     

PM10 and PM2.5 concentrations in Central and Eastern Europe:: results from the Cesar study

Between November 1995 and October 1996, particulate matter concentrations (PM₁₀ and PM_2.5) were measured in 25 study areas in six Central and Eastern European countries: Bulgaria, Czech Republic, Hungary, Poland, Romania and Slovak Republic. To assess annual mean concentration levels, 24-h averaged concentrations were measured every sixth day on a fixed urban background site using Harvard impactors with a 2.5 and 10 μm cut-point. The concentration of the coarse fraction of PM₁₀ (PM_10−2.5) was calculated as the difference between the PM₁₀ and the PM_2.5 concentration. Spatial variation within study areas was assessed by additional sampling on one or two urban background sites within each study area for two periods of 1 month. QA/QC procedures were implemented to ensure comparability of results between study areas. A two to threefold concentration range was found between study areas, ranging from an annual mean of 41 to 98 μg m⁻³ for PM₁₀, from 29 to 68 μg m⁻³ for PM_2.5 and from 12 to 40 μg m⁻³ for PM_10−2.5. The lowest concentrations were found in the Slovak Republic, the highest concentrations in Bulgaria and Poland. The variation in PM₁₀ and PM_2.5 concentrations between study areas was about 4 times greater than the spatial variation within study areas suggesting that measurements at a single sampling site sufficiently characterise the exposure of the population in the study areas. PM₁₀ concentrations increased considerably during the heating season, ranging from an average increase of 18 μg m⁻³ in the Slovak Republic to 45 μg m⁻³ in Poland. The increase of PM₁₀ was mainly driven by increases in PM_2.5; PM_10−2.5 concentrations changed only marginally or even decreased. Overall, the results indicate high levels of particulate air pollution in Central and Eastern Europe with large changes between seasons, likely caused by local heating.     

Spatial patterns of mobile source particulate matter emissions-to-exposure relationships across the United States

Assessing the public health benefits from air pollution control measures is assisted by understanding the relationship between mobile source emissions and subsequent fine particulate matter (PM_2.5) exposure. Since this relationship varies by location, we characterized its magnitude and geographic distribution using the intake fraction (iF) concept. We considered emissions of primary PM_2.5 as well as particle precursors SO₂ and NO_x from each of 3080 counties in the US. We modeled the relationship between these emissions and total US population exposure to PM_2.5, making use of a source–receptor matrix developed for health risk assessment. For primary PM_2.5, we found a median iF of 1.2 per million, with a range of 0.12–25. Half of the total exposure was reached by a median distance of 150 km from the county where mobile source emissions originated, though this spatial extent varied across counties from within the county borders to 1800 km away. For secondary ammonium sulfate from SO₂ emissions, the median iF was 0.41 per million (range: 0.050–10), versus 0.068 per million for secondary ammonium nitrate from NO_x emissions (range: 0.00092–1.3). The median distance to half of the total exposure was greater for secondary PM_2.5 (450 km for sulfate, 390 km for nitrate). Regression analyses using exhaustive population predictors explained much of the variation in primary PM_2.5 iF (R²=0.83) as well as secondary sulfate and nitrate iF (R²=0.74 and 0.60), with greater near-source contribution for primary than for secondary PM_2.5. We conclude that long-range dispersion models with coarse geographic resolution are appropriate for risk assessments of secondary PM_2.5 or primary PM_2.5 emitted from mobile sources in rural areas, but that more resolved dispersion models are warranted for primary PM_2.5 in urban areas due to the substantial contribution of near-source populations.     

Particulate matter and manganese exposures in Toronto,Canada

Methylcyclopentadienyl manganese tricarbonyl (MMT) is a manganese-based gasoline additive used to enhance automobile performance. MMT has been used in Canadian gasoline for about 20 yr. Because of the potential for increased levels of Mn in particulate matter resulting from automotive exhausts, a large-scale population-based exposure study (∼1000 participant periods) was conducted in Toronto, Canada, to estimate the distribution of 3-day average personal exposures to particulate matter (PM_2.5 and PM₁₀) and Mn. A stratified, three-stage, two-phase probability, longitudinal sample design of the metropolitan population was employed. Residential indoor and outdoor, and ambient levels (at a fixed site and on a roof) of PM_2.5, PM₁₀, and Mn were also measured. Supplementary data on traffic counts, meteorology, MMT levels in gasoline, personal occupations, and activities (e.g. amount of vehicular usage) were collected. Overall precision (%RSD) for analysis of duplicate co-located samples ranged from 2.5 to 5.0% for particulate matter and 3.1 to 5.5% for Mn. The detection limits were 1.47 and 3.45 μg m^-3 for the PM₁₀ and PM_2.5 fractions, respectively, and 5.50 and 1.83 ng m^-3 for Mn in PM₁₀ and PM_2.5, respectively. These low detection limits permitted the reporting of concentrations for >98% of the samples. For PM₁₀, the personal particulate matter levels (median 48.5 μg m^-3) were much higher than either indoor (23.1 μg m^-3) or outdoor levels (23.6 μg m^-3). The median levels for PM_2.5 for personal, indoor, and outdoor were 28.4, 15.4 and 13.2 μg m^-3, respectively. The correlation between PM_2.5 personal exposures and indoor concentrations was high (0.79), while correlations between personal and the outdoor, fixed site and roof site were low (0.16–0.27). Indoor Mn concentration distributions (in PM_2.5 and PM₁₀), unlike particulate matter, exhibited much lower and less variable levels that the corresponding outdoor data. The median personal exposure was 8.0 ng m^-3, compared with 4.7 and 8.6 ng m^-3, respectively, for the indoor and outdoor distributions. The highest correlations occurred for personal vs indoor data (0.56) and for outdoor vs roof site data (0.66), and vs fixed site data (0.56). The concentration of Mn in particulate matter, expressed in ppm (w/w), revealed that the fixed site was the highest, followed by the roof site, outdoor, indoor, and personal. The personal and indoor data showed a statistically significant correlation (0.68) while all other correlations between personal or indoor data and outdoor or fixed-site data were quite small. The low correlations of personal and indoor levels with outdoor levels suggest that different sources in the indoor and outdoor microenvironments produce particle matter with dissimilar composition. The correlation results indicate that neither the roof- nor fixed-site concentrations can adequately predict personal particulate matter or Mn exposures.     

Study of aluminium distribution and speciation in atmospheric particles of different diameters in Nanjing,China

Aluminium (Al) is one of the trace inorganic metals present in atmospheric particles. Al speciation study is essential to better evaluate the mobility, availability, and persistence of trace Al and Al species in the atmosphere. This paper reports Al distribution and speciation in atmospheric particles with aerodynamic diameters >10.0, 10.0–2.5 and <2.5 μm in the urban area of Nanjing, China. Urban particles were collected with a high-volume sampling system equipped with a cascade impactor, which effectively separates the particulate matter into three size ranges. Particulate Al was fractionated into five different forms (insoluble, oxide, organic, carbonate, and exchangeable species) by the modified five-step Tessier's sequential extraction procedure. The main points are as follows: (1) The average levels of Al in PM_2.5, PM_2.5–10 and PM_>10 are 2.02±0.35, 3.04±0.43 and 6.32±0.76 μg m⁻³, respectively, with PM_2.5, PM_2.5–10 and PM_>10 constituting respectively, 17.8±3.1%, 26.7±3.8% and 55.5±6.7% of suspended particulate matter (SPM) mass (11.38 μg m⁻³). (2) The vertical profile of airborne Al in the above three size fractions has been estimated. A significant increase in airborne Al concentrations was found for PM_2.5, PM_2.5–10 and PM_>10 as the sampling height above the ground increased from 2.5 to 17.5 m; however, there was an obvious decrease in airborne Al concentrations between 17.5 and 40.0 m. The maximum mean of total Al in PM_2.5, PM_2.5–10 and PM_>10 occurred between 12.5 and 20.0 m above the ground. (3) The distribution of Al speciation was studied. It was found that the size distribution of airborne Al species followed the order: insoluble species>oxide species>organic species>carbonate species>exchangeable species.     

Spatial variation of mass concentration of roadside suspended particulate matter in metropolitan Hong Kong

This study conducted roadside particulate sampling to measure the total suspended particulate (TSP), PM₁₀ (particles <10 μm in aerodynamic diameter) and PM_2.5 (particles <2.5 μm in aerodynamic diameter) mass concentration in 11 urbanized and densely populated districts in Hong Kong. One hundred and thirty-three samples were obtained to measure the mass concentrations of TSP, PM₁₀ and PM_2.5. According to these results, the TSP, PM₁₀ and PM_2.5 mass concentrations varied from 94.85 to 301.63 μg m⁻³, 67.67 to 142.68 μg m⁻³ and 50.01 to 125.12 μg m⁻³, respectively. The PM_2.5/PM₁₀ ratio of all samples was 0.82 which ranged from 0.62 to 0.95. The PM levels and PM ratios in metropolitan Hong Kong significantly fluctuated from site-to-site and over time. The PM_2.5 mass concentration in different districts corresponding to urban industrial, new town, urban residential and urban commercial were 77.64, 87.50, 106.96 and 88.54 μg m⁻³, respectively. The PM_2.5 level is high in Hong Kong, and for individual sampling, more than 60% daily measurements exceeded the NAAQS. The mass fraction of PM_2.5 in PM₁₀ and TSP is relatively high when compared with overseas studies.     

Secondary aerosol formation through photochemical reactions estimated by using air quality monitoring data in Taipei City from 1994 to 2003

Analyses of diurnal patterns of PM₁₀ in Taipei City have been performed in this study at different daily ozone maximum concentrations (O_3,max) from 1994 to 2003. In order to evaluate secondary aerosol formation at different ozone levels, CO was used as a tracer of primary aerosol, and O_3,max was used as an index of photochemical activity. Results show that when O_3,max exceeds 120 ppb, the highest photochemical formation of secondary aerosol can be found at 15:00 (local time). The produced secondary aerosol is estimated to contribute 30 μg m⁻³ (43%) of PM₁₀ concentration, and about 77% of the estimated secondary PM₁₀ is composed of PM_2.5. The estimated maximum concentration of secondary aerosol occurs 2–3 h later than the maximum ozone concentration. As revealed in an O₃ episode, PM₁₀ and PM_2.5 vary consistently with O₃ at daytime, which suggests that they are mostly secondary aerosols produced from photochemical reactions. Data collected from Taipei aerosol supersite in 2002 indicates that for all O₃ levels, summertime PM_2.5 is composed of 23%, 20%, 9%, and 7% of organic carbon, sulfate, nitrate, and elemental carbon, respectively. Aerosol number and volume size spectra are dominated by submicron particles either from pollution transport or photochemical reactions. Secondary PM₁₀ concentrations show increasing tendencies for the time between 15:00 and 19:00 from 1994–1996 to 2001–2003. This reveals that the abatement of secondary PM₁₀ becomes more important after pronounced primary PM₁₀ reduction in a metropolis.     

Characteristics of vertical profiles and sources of PM2.5, PM10 and carbonaceous species in Beijing

In August 2003 during the anticipated month of the 2008 Beijing Summer Olympic Games, we simultaneously collected PM₁₀ and PM_2.5 samples at 8, 100, 200 and 325 m heights up a meteorological tower and in an urban and a suburban site in Beijing. The samples were analysed for organic carbon (OC) and elemental carbon (EC) contents. Particulate matter (PM) and carbonaceous species pollution in the Beijing region were serious and widespread with 86% of PM_2.5 samples exceeding the daily National Ambient Air Quality Standard of the USA (65 μg m⁻³) and the overall daily average PM₁₀ concentrations of the three surface sites exceeding the Class II National Air Quality Standard of China (150 μg m⁻³). The maximum daily PM_2.5 and PM₁₀ concentrations reached 178.7 and 368.1 μg m⁻³, respectively, while those of OC and EC reached 22.2 and 9.1 μg m⁻³ in PM_2.5 and 30.0 and 13.0 μg m⁻³ in PM₁₀, respectively. PM, especially PM_2.5, OC and EC showed complex vertical distributions and distinct layered structures up the meteorological tower with elevated levels extending to the 100, 200 and 300 m heights. Meteorological evidence suggested that there exist fine atmospheric layers over urban Beijing. These layers were featured by strong temperature inversions close to the surface (<50 m) and more stable conditions aloft. They enhanced the accumulation of pollutants and probably caused the complex vertical distributions of PM and carbonaceous species over urban Beijing. The built-up of PM was accompanied by transport of industrial emissions from the southwest direction of the city. Emissions from road traffic and construction activities as well as secondary organic carbon (SOC) are important sources of PM. High OC/EC ratios (range of 1.8–5.1 for PM_2.5 and 2.0–4.3 for PM₁₀) were found, especially in the higher levels of the meteorological tower suggesting there were substantial productions of SOC in summer Beijing. SOC is estimated to account for at least 33.8% and 28.1% of OC in PM_2.5 and PM₁₀, respectively, with higher percentages at the higher levels of the tower.     

Estimation of wind blown dust emissions in Europe and its vicinity

The assessment of the wind blown dust emission for Europe and selected regions of North Africa and Southwest Asia was carried out using a mesoscale model. The mesoscale model was parameterized based on the current literature review. The model provides data on PM₁₀ emission from several dust reservoirs (anthropogenic, agriculture, semi- and natural) with spatial resolution of 10 × 10 km and temporal resolution of 1 h. The spatial variability of PM₁₀ emission depends on soil texture, land cover/land use as well as meteorological conditions. Lands covered with water or permanently wet were excluded from the model. The land covered with vegetation is treated as dust reservoir whose dust emission capacity depends on the type of vegetation and cover. The dust reservoirs are divided into reservoirs with stable and unstable surface. The changes of emission in time depend on meteorological parameters.The wind blown dust emission should be treated as a non-continuous spatio-temporal process. The emissions are estimated with high uncertainty. The estimated PM₁₀ yearly total load emitted by wind from the European territory is highly differentiated in space and time and is equal to 0.74 Tg. The total load of PM₁₀ emitted by wind from North African and Southwest Asian land surface located in the vicinity of European boundaries is assessed as nearly 50% (0.43 Tg) of the total load estimated for the whole Europe.The average yearly PM₁₀ emission factor for Europe was estimated at 0.139 Mg km^?2.The PM₁₀ emission from agricultural areas is estimated at 52% of the total wind blown emission from the domain of the European Union project “Improving and applying methods for the calculation of natural and biogenic emissions and assessment of impacts to the air quality” - NatAir.PM₁₀ emission factor for natural areas of Europe is estimated at 0.021 Mg km^?2. Appropriate factors for agricultural areas and anthropogenic areas are 0.157 Mg km^?2 and 0.118 Mg km^?2, respectively. The latter two factors are probably underestimated due to omitting in the model of other dust emission mechanisms than aeolian erosion.     

Seasonal and spatial trends in the sources of fine particle organic carbon in Israel,Jordan, and Palestine

A study of carbonaceous particulate matter (PM) was conducted in the Middle East at sites in Israel, Jordan, and Palestine. The sources and seasonal variation of organic carbon, as well as the contribution to fine aerosol (PM_2.5) mass, were determined. Of the 11 sites studied, Nablus had the highest contribution of organic carbon (OC), 29%, and elemental carbon (EC), 19%, to total PM_2.5 mass. The lowest concentrations of PM_2.5 mass, OC, and EC were measured at southern desert sites, located in Aqaba, Eilat, and Rachma. The OC contribution to PM_2.5 mass at these sites ranged between 9.4% and 16%, with mean annual PM_2.5 mass concentrations ranging from 21 to 25 ug m^?3. These sites were also observed to have the highest OC to EC ratios (4.1–5.0), indicative of smaller contributions from primary combustion sources and/or a higher contribution of secondary organic aerosol. Biomass burning and vehicular emissions were found to be important sources of carbonaceous PM in this region at the non-southern desert sites, which together accounted for 30%–55% of the fine particle organic carbon at these sites. The fraction of measured OC unapportioned to primary sources (1.4 μgC m^?3 to 4.9 μgC m^?3; 30%–74%), which has been shown to be largely from secondary organic aerosol, is relatively constant at the sites examined in this study. This suggests that secondary organic aerosol is important in the Middle East during all seasons of the year.     

Field performance of dichotomous sequential PM air samplers

For over one year, the Environmental Protection Commission of Hillsborough County (EPCHC) in Tampa, Florida, operated two dichotomous sequential particulate matter air samplers collocated with a manual Federal Reference Method (FRM) air sampler at a waterfront site on Tampa Bay. The FRM was alternately configured as a PM_2.5, then as a PM₁₀ sampler. For the dichotomous sampler measurements, daily 24-h integrated PM_2.5 and PM_10–2.5 ambient air samples were collected at a total flow rate of 16.7 l min⁻¹. A virtual impactor split the air into flow rates of 1.67 and 15.0 l min⁻¹ onto PM_10–2.5 and PM_2.5 47-mm diameter PTFE^® filters, respectively. Between the two dichotomous air samplers, the average concentration, relative bias and relative precision were 13.3 μg m⁻³, 0.02% and 5.2% for PM_2.5 concentrations (n=282), and 12.3 μg m⁻³, 3.9% and 7.7% for PM_10–2.5 concentrations (n=282). FRM measurements were alternate day 24-h integrated PM_2.5 or PM₁₀ ambient air samples collected onto 47-mm diameter PTFE^® filters at a flow rate of 16.7 l min⁻¹. Between a dichotomous and a PM_2.5 FRM air sampler, the average concentration, relative bias and relative precision were 12.4 μg m⁻³, −5.6% and 8.2% (n=43); and between a dichotomous and a PM₁₀ FRM air sampler, the average concentration, relative bias and relative precision were 25.7 μg m⁻³, −4.0% and 5.8% (n=102). The PM_2.5 concentration measurement standard errors were 0.95, 0.79 and 1.02 μg m⁻³; for PM₁₀ the standard errors were 1.06, 1.59, and 1.70 μg m⁻³ for two dichotomous and one FRM samplers, respectively, which indicate the dichotomous samplers have superior technical merit. These results reveal the potential for the dichotomous sequential air sampler to replace the combination of the PM_2.5 and PM₁₀ FRM air samplers, offering the capability of making simultaneous, self-consistent determinations of these particulate matter fractions in a routine ambient monitoring mode.     

Dispersion modelling of a wintertime particulate pollution episode in Christchurch,New Zealand

This paper examines the inter-suburb dispersion of particulate air pollution in Christchurch, New Zealand, during a wintertime particulate pollution episode. The dispersion is simulated using the RAMS/CALMET/CALPUFF modelling system, with data from a detailed emissions inventory of home heating, motor vehicles and industry. During the period 27 July–1 August 1995, peak 1 h and 24 h PM₁₀ concentrations of 368 and 107 μg m⁻³, respectively, were observed. Peak concentrations occurred at night, when particulate emissions from wood- and coal-burning domestic heating appliances were at a maximum and emitted into a stable boundary layer. The model is generally able to reproduce the observed PM₁₀ time series recorded at surface monitors located throughout the urban area. For this simulation, the fractional gross error ranges between 0.69 and 0.99, and the fractional bias ranges between −0.17 and 0.30. Strong horizontal concentration gradients of 100 μg m⁻³ km⁻¹, both in the observational record and model predictions, are apparent. Three emission reduction options, designed to reduce the severity of particulate pollution episodes in Christchurch, are simulated. When both domestic open-hearth fires and all coal burning are removed, the 24 h average peak concentration is reduced by 55%. The number of guideline exceedences of PM₁₀ in the modelled period is reduced from five to one. Removing open-hearth fires results in 42% reduction in PM₁₀ concentration, resulting in three exceedences of the guideline, and removing coal-burning fires yields a 32% reduction in PM₁₀, resulting in four exceedences of the guideline.     

Speciated mercury in size-fractionated particles in Shanghai ambient air

Size-fractionated particles were collected at two sites from July 2004 to April 2006 in Shanghai. The mercury in particles was extracted and divided operationally into four species: exchangeable particulate mercury (EXPM), HCl-soluble particulate mercury (HPM), elemental particulate mercury (EPM) and residual particulate mercury. The total particulate Hg concentration during the study period ranged from 0.07 ng m^?3 to 1.45 ng m^?3 with the average 0.56 ± 0.22 ng m^?3 at site 1, while 0.20 ng m^?3–0.47 ng m^?3 with the average 0.33 ± 0.09 ng m^?3 at site 2, which is far higher than some foreign cities and comparable to some cities with heavy air pollution in China. The Hg mass content also displayed evident size distribution, with higher value in PM_1.6–3.7, somewhat higher or lower than the source profile. EXAM was only found in the summer, HPM have higher percentage in summer and fall rather than in winter and spring. The different mercury species showed different correlation to temperature, relative humidity, wind speed. HPM positively depends on temperature at both sites which implies the importance of mercury transformation on particles. In foggy days TPM increased greatly, but HPM didn't vary greatly as anticipated. Instead, RPM gained a distinguished increase. It demonstrated that aqueous reaction and complex heterogenic reactions in droplet might happen in acidic environment. The correlation of mercury with other pollutants including SO₂, NO₂, CO and PM₁₀ varies with the different mercury forms. Hybrid single-particle lagrangian integrated trajectories (HYSPLIT) model was used to back trace air mass at different representative days and results indicated that transportation from Huabei Plain will increase mercury concentration in winter and fall to some extent. The possible existing compounds and their atmospheric behavior of HPM, EPM and RPM were calculated and the compared to analyze its implication on atmospheric mercury cycle.     

Source apportionment of ambient PM2.5 at five spanish centres of the european community respiratory health survey (ECRHS II)

Fine particulate matter (PM_2.5) was sampled at 5 Spanish locations during the European Community Respiratory Health Survey II (ECRHS II). In an attempt to identify and quantify PM_2.5 sources, source contribution analysis by principal component analysis (PCA) was performed on five datasets containing elemental composition of PM_2.5 analysed by ED-XRF. A total of 4–5 factors were identified at each site, three of them being common to all sites (interpreted as traffic, mineral and secondary aerosols) whereas industrial sources were site-specific. Sea-salt was identified as independent source at all coastal locations except for Barcelona (where it was clustered with secondary aerosols). Despite their typically dominant coarse grain-size distribution, mineral and marine aerosols were clearly observed in PM_2.5. Multi-linear regression analysis (MLRA) was applied to the data, showing that traffic was the main source of PM_2.5 at the five sites (39–53% of PM_2.5, 5.1–12.0 μg m⁻³), while regional-scale secondary aerosols accounted for 14–34% of PM_2.5 (2.6–4.5 μg m⁻³), mineral matter for 13–31% (2.4–4.6 μg m⁻³) and sea-salt made up 3–7% of the PM_2.5 mass (0.4–1.3 μg m⁻³). Consequently, despite regional and climatic variability throughout Spain, the same four main PM_2.5 emission sources were identified at all the study sites and the differences between the relative contributions of each of these sources varied at most 20%. This would corroborate PM_2.5 as a useful parameter for health studies and environmental policy-making, owing to the fact that it is not as subject to the influence of micro-sitting as other parameters such as PM₁₀. African dust inputs were observed in the mineral source, adding on average 4–11 μg m⁻³ to the PM_2.5 daily mean during dust outbreaks. On average, levels of Al, Si, Ti and Fe during African episodes were higher by a factor of 2–8 with respect to non-African days, whereas levels of local pollutants (absorption coefficient, S, Pb, Cl) showed smaller variations (factor of 0.5–2).     

Spatial representativeness and scales of transport during the 1995 integrated monitoring study in California's San Joaquin Valley

Daily measurements of PM₁₀ mass and chemical composition were obtained for the period 1–14 November 1995 from a saturation monitoring network around Corcoran, and for varying portions of the period 9 December 1995–6 January 1996 for three networks around Bakersfield, Fresno, and the Kern Wildlife Refuge, in California's San Joaquin Valley. During the latter period, monitoring locations were also operated along the boundaries and across the width of the Valley. The Corcoran, Bakersfield, and Fresno networks consisted of 12–25 sites, located in areas of about 300–800 km². Each network also included one core site, situated at a pre-existing monitoring location, with more extensive and more temporally resolved measurements. Mean concentrations of PM₁₀ and its constituents varied from core-site concentrations by 20% or more over distances ranging from 4 to 14 km. Local source influences were observed to affect sites over distances of less than 1 km, but primary particulate emissions were also transported over urban or sub-regional scales of approximately 10–30 km during the winter and greater than 30 km in the fall. During winter, gas-phase precursors of secondary aerosol may have been transported over distances of approximately 100 km, but little evidence was found for transport of primary PM on such a scale.     

Estimation and characterization of children’s ambient generated exposure to PM2.5 using sulphate and elemental carbon as tracers

Children’s exposures to ambient and non-ambient fine particulate matter (PM_2.5) were determined using the sulphate and elemental carbon components of the PM_2.5 mixture as tracers of the ambient contribution during a 6-week winter period in Prince George, British Columbia, Canada. Personal exposures to PM_2.5 were measured in children at 5 elementary schools located throughout the city and ambient samples were collected on school rooftops. Average ambient levels and personal exposures during this time period were 13.8 μg m^?3 and 16.4 μg m^?3 respectively. From the data pooled across individuals, use of the two different tracers indicated identical estimates of median exposure to ambient PM_2.5 (7.5 μg m^?3) and similar estimates of non-ambient generated exposure (6.4 and 5.0 μg m^?3) and infiltration (0.49 and 0.52) for the sulphate and elemental carbon approach, respectively. The median fraction of the ambient concentration resulting in exposure or exposure factors were 0.54 and 0.55 respectively, however lower values of 0.46 and 0.42 were determined from regression analysis. A strong association was found between exposure to ambient PM_2.5 and measured ambient concentrations at both the closest school monitor (median r = 0.92) and a central site (median r = 0.88) demonstrating that the central site monitor was suitable for assessing longitudinal ambient generated exposure throughout the city. These results support the use of elemental carbon as a tracer of ambient generated exposure and the use of ambient data as estimates of longitudinal changes in children’s exposure in this setting. The importance of both ambient and non-ambient sources of PM_2.5 is emphasized by their almost equal contribution to total personal exposures. Comparison with other studies suggests a limited influence of climate and the cold season in Prince George on exposure levels and found similar mean non-ambient generated exposures despite large variability across and within subjects in any given location.     

Characterization of size-fractionated particulate mercury in Shanghai ambient air

The size-fractionated particulate mercury in ambient air was collected at the top of a university campus building in Shanghai from March 2002 to September 2003. Wet digestion followed by cold vapor atom adsorption spectroscopy (CVAAS) was employed to analyze total particulate mercury concentration. Two-step extraction was performed to differentiate volatile particle-phase mercury (VPM), reactive particle-phase mercury (RPM) and inert particle-phase mercury (IPM). The average concentrations of mercury in PM_1.6, PM₈ and total suspended particle (TSP) were 0.058–0.252, 0.148–0.398 and 0.233–0.529 ng m⁻³, respectively. About 50%–60% of mercury in PM₈ was in PM_1.6, and about 60%–70% of mercury in TSP was in PM₈. Particulate mercury was mainly concentrated on fine particles. The mercury fraction in fine particulate matters (<1.6 μm) was over 4 μg g⁻¹ while 1–2 μg g⁻¹ in TSP. Both were much higher than background values, suggesting that anthropogenic sources are the predominant emission contributors. Seasonal variation indicated that the mercury in TSP in spring was higher than that in summer; however, the mercury in fine particles (<1.6 μm) varied little. The fact that fine particulate mercury (<1.6 μm) was well correlated with sulfate and elemental carbon, but not with fluoride, chloride, nitrate and organic carbon, demonstrates that fine particulate mercury is closely associated with stationary sources and gas–particle transformation. Speciation analysis of mercury showed that VPM fraction decreased with the decrease of particle size, while IPM fraction increased and occupied over 50% in particle <1.6 μm. The detailed species in VPM, RPM and IPM were discussed. Coal burning was estimated to contribute approximately 80% of total atmospheric mercury.     

Spatial and chemical patterns of PM10 in road dust deposited in urban environment

Recent research interest has been focused on road dust resuspension as one of the major sources of atmospheric particulate matter in an urban environment. Given the dearth of studies on the variability of the PM₁₀ fraction of road deposited sediments, our understanding of the main factors controlling this pollutant is incomplete. In the present study a new sampling methodology was devised and applied to collect PM₁₀ deposited mass from 1 m² of road pavement. PM₁₀ road dust fraction was sampled directly from active traffic lanes at 23 sampling sites during a campaign in Barcelona (Spain) in June 2007. The aim of the study was to gain more insight into the variability of mass and chemistry of road dust in different urban environments, such as the city centre, ring roads, and locations nearby demolition/construction sites. The city centre showed values of PM₁₀ road dust within a range of 3–23 mg m^?2, whereas levels reached 24–80 mg m^?2 in locations affected by transport of uncovered heavy trucks. The largest dust loads were measured in the proximity of demolition/construction sites and the harbor entry with values up to 328 mg m^?2.The city centre road dust profiles (%) were enriched in OC, EC, Fe, S, Cu, Zn, Mn, Cr, Sb, Sn, Mo, Zr, Hf, Ge, Ba, Pb, Bi, SO₄^2?, NO₃^?, Cl^? and NH₄⁺, but several crustal components such as Ca, Ti, Na, and Mg were also considerably concentrated. Locations affected by construction and demolition activities had high levels of crustal components such as Ca, Li, Sc, Sr, Rb and also As whereas ring roads, characterized by a higher load of uncovered heavy trucks showed an intermediate composition.Levels of PM₁₀ components per area were also evaluated to quantify the resuspendable amount of each element from 1 m². In the inner city environment mean values of 1363 μg Ca m^?2, 816 μg OC m^?2, 239 μg EC m^?2, 13 μg Cu m^?2, 12 μg Zn m^?2, 1.9 μg Sb m^?2 and 2.0 μg Pb m^?2, in PM₁₀ in all cases, were registered.Moreover the deposited PM load at demolition/construction sites acts as a reservoir or trap for traffic-related particles, which gives rise to large amounts of hazardous pollutants, available for resuspension.