Outdoor air particle-bound trace metals in four selected communities in Ibadan,Nigeria

Trace metal concentrations were determined in particulate matter (PM₁₀) in ambient air of four purposively selected residential areas in Ibadan, Nigeria namely Bodija market (BM), Ojo Park (OP), Oluyole Estate (OE) and University of Ibadan (UI). PM₁₀ was determined in the morning (7–10 a.m.) and afternoon (2–5 p.m.) for 12 weeks in the dry season months of January–March using a volumetric sampler following standard procedures and levels compared with WHO guideline limits. Glass-fibre filter papers exposed to the particulate matter were digested using appropriate acid mixtures, and the digest analysed for trace metals including Ni, Cr, Mn, Zn, and Pb using ICPMS method and levels compared with WHO limits. Data was analysed using ANOVA and Pearson correlation test at 5 % level of significance. The highest mean PM₁₀ concentrations 502.3 ± 39.9 μg/m³ were recorded in the afternoon period at BM, while the lowest concentration 220.6 ± 69.9 μg/m³ was observed in the morning hours at UI. There was a significant difference between the PM₁₀ levels across the various locations (p < 0.05), and all the levels were higher than WHO limit of 50 μg/m³. The highest levels of Ni, Zn and Pb were recorded at BM, which also had the highest PM₁₀ burden. The trend in Pb levels across the locations was BM > UI > OP > OE with the highest level 5.70 μg/m³ in BM nearly fourfolds WHO limits of 1.5 μg/m³. There was a significant correlation between PM₁₀ and Ni (p < 0.05).Urban communities with increased human activities especially motor traffic recorded both higher levels of PM₁₀ and toxic trace metals. There is need to carry out source apportionment to establish the origin of these trace metals in future studies.     

Airborne fine particulate matter (PM2.5) at industrial,high- and low-density residential sites in a Nigerian megacity

Abstract

Airborne particulate matter PM_2.5 was collected in an industrial, a low-density, and a high-density residential area of Lagos from December 2010 to November 2011, and elemental composition was determined by proton-induced X-ray emission. Across the months, mass concentrations ranged from 13 to 237?µg?m^?3, exceeding the World Health Organization guideline value of 10?µg?m^?3. Data on 24 elements were obtained, with maximum values during Harmattan season months; source identification and apportionment studies by positive matrix factorization suggested that petroleum oil combustion (70%) was the major source of PM_2.5 and could pose a great hazard to Lagos receptors.     

PIXE characterization of PM10 and PM2.5 particulates sizes collected in Ikoyi Lagos,Nigeria

Ambient concentrations of PM₁₀ (x?≤?10?µm) and PM_2.5 (x?≤?2.5?µm) particulate fractions collected from Ikoyi Lagos, Nigeria, as well as their elemental compositions are presented in this study. Both size-segregated fractions were collected using a double staged ‘Gent’ stack filter unit sampler. Elemental characterizations of dust laden filters were carried out using proton-induced X-ray emission (PIXE) technique. Twenty-two elements (Si, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Pb, Br, Rb, Sr, Zr, Ag, Cd, and Ta) were detected as well as their concentrations and correlations were determined for both particulate size fractions. Their correlation matrix result indicates that some of the trace elements detected could have common source origins or similar chemical properties. The results were similar to the levels observed in moderately polluted urban areas and there is need for source identification and apportionment using receptor models in future studies.     

High seasonal variation of atmospheric C and particle concentrations in Delhi,India

The highly populated Indian regions are currently in a phase of rapid economic growth resulting in high emissions of carbonaceous aerosols. This leads to poor air quality and impact on climate. The chemical composition of carbonaceous aerosols has rarely been studied in industrial areas of India. Here, we investigated carbonaceous aerosols in particulate matter (PM) monthly in the industrial area of Delhi in 2011. The concentrations of organic C and elemental C in PM₁₀ fraction were analyzed. Results show a clear seasonal variability of organic and elemental C. PM₁₀ ranged 95.9–453.5 μg m^?3, organic C ranged 28.8–159.4 μg m^?3, and elemental C ranged 7.5–44.0 μg m^?3; those values were higher than reported values. Organic and elemental C were correlated with each other in pre-monsoon and winter seasons, implying the existence of similar emission sources such as coal combustion, biomass burning and vehicular exhaust. The annual average contribution of total carbonaceous aerosols in PM₁₀ was estimated as 62 %.     

Trace elements in particulate matter of ambient air at petroleum filling stations

Size segregated suspended particulate matter (PM_2.5 and PM_10-2.5) in air at four major petroleum-filling stations in Ile-Ife, Nigeria, were monitored using double staged “Gent” stacked samplers to assess variations in mass loads and elemental concentrations of 25 elements. Na, Mg, Al, Si, P, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Br, Rb, Sr, Zr, Cs, Ta, W, and Pb were determined in both fractions by external ion beam proton-induced X-ray emission technique. Enrichment factors and pollution indices were calculated and results revealed that most elements were anthropogenic in both fractions with concentrations exceeding the World Health Organization guideline standards.     

PM<Subscript>2.5</Subscript> particulates and metallic elements (Ni,Cu, Zn,Cd and Pb) study in a mixed area of summer season in Shalu,Taiwan

PM_2.5 has become an important environmental issue in Taiwan during the past few years. Moreover, electricity increased significantly during the summertime and TTPP generated by coal burning base is the main electricity provider in central Taiwan. Therefore, summer season has become the main research target in this study. The ambient air concentrations of particulate matter PM_2.5 and PM₁₀ collected by using VAPS at a mixed characteristic sampling site were studied in central Taiwan. The results indicated that the average daytime PM_2.5 and PM₁₀ particulate concentrations were occurred in May and they were 44.75 and 57.77 µg/m³ in this study. The results also indicated that the average nighttime PM_2.5 and PM₁₀ particulate concentrations were occurred in June and they were 38.19 and 45.79 µg/m³ in this study. The average PM_2.5/PM₁₀ ratios were 0.7 for daytime, nighttime and 24-h sampling periods in the summer for this study. This value was ranked as the lowest ratios when compared to the other seasons in previous study. Noteworthy, the results further indicated that the metallic element Pb has the mean highest concentrations for 24-h, daytime and nighttime sampling periods when compared to those of the other metallic elements (Ni, Cu, Zn and Cd). The average mean highest metallic Pb concentrations in PM10 were 110.7, 203.0 and 207.2 ng/m³ for 24-h, daytime and nighttime sampling periods in this study. And there were 59.53, 105.2 and 106.6 ng/m³ for Pb in PM2.5 for 24-h, daytime and nighttime sampling periods, respectively. Moreover, the results further indicated that mean metallic element Pb concentrations on PM_2.5 and PM₁₀ were all higher than those of the other elements for 24 h, day and nighttime.     

Characteristics,sources and health risk assessment of toxic heavy metals in PM<Subscript>2.5</Subscript> at a megacity of southwest China

Twenty trace elements in fine particulate matters (i.e., PM_2.5) at urban Chengdu, a southwest megacity of China, were determined to study the characteristics, sources and human health risk of particulate toxic heavy metals. This work mainly focused on eight toxic heavy metal elements (As, Cd, Cr, Cu, Mn, Ni, Pb and Zn). The average concentration of PM_2.5 was 165.1 ± 84.7 µg m^?3 during the study period, significantly exceeding the National Ambient Air Quality Standard (35 µg m^?3 in annual average). The particulate heavy metal pollution was very serious in which Cd and As concentrations in PM_2.5 significantly surpassed the WHO standard. The enrichment factor values of heavy metals were typically higher than 10, suggesting that they were mainly influenced by anthropogenic sources. More specifically, the Cr, Mn and Ni were slightly enriched, Cu was highly enriched, while As, Cd, Pb and Zn were severely enriched. The results of correlation analysis showed that Cd may come from metallurgy and mechanical manufacturing emissions, and the other metals were predominately influenced by traffic emissions and coal combustion. The results of health risk assessment indicated that As, Mn and Cd would pose a significant non-carcinogenic health risk to both children and adults, while Cr would cause carcinogenic risk. Other toxic heavy metals were within a safe level.     

Air pollution below WHO levels decreases by 40 % the links of terrestrial microbial networks

Air pollution has a deleterious impact on public health and the environment. There is few knowledge on the effect of air pollution on terrestrial microbial communities, despite the major role of microbes in ecosystems. Here, we designed an in situ trial ecosystem to assess the impact of moderate atmospheric pollution, below World Health Organization (WHO) thresholds, on an indigenous microbial communities, including bacteria, fungi, ciliates, algae, cyanobacteria, testate amoebae, rotifers and nematodes, extracted from terrestrial bryophytes. These micro-ecosystems were placed at a rural, an urban and an industrial site in France and were thus exposed to various levels of nitrogen dioxide (NO₂), from 6.6–67.9 μg·m^?3, and particulate matter, from 0.7–7.9 μg·m^?3. Microbial analysis was performed by microscopy. We determined atmospheric temperature, relative humidity and particulate matter with diameter lower than 10 µm (PM₁₀), Cu, Cr, Fe, Ni, Pb, Zn in PM₁₀, and (NO₂). Results show a significant impact of chronic moderate exposure to NO₂ and copper Cu-associated particulate matter on the global microbial network complexity. This is evidenced by a loss of about 40 % of microbial co-occurrence links during incubation. Most lost microbial links are ecologically positive links. Moreover, most changes in community co-occurrence networks are related to testate amoebae, a major top predator of microbes. Overall, our findings demonstrate that air pollution can have strong deleterious effects on microbial interactions, even at levels below WHO thresholds.     

Air pollutant levels are 12 times higher than guidelines in Varanasi,India. Sources and transfer

Air quality in an urban atmosphere is regulated by both local and distant emission sources. For air quality management in urban areas, identification of sources and their relationships with local meteorology and air pollutants are essential. The critical condition of air quality in Indo-Gangetic plain is well known, but lack of data on both local and distant emission sources limits the scope of improving air quality in this region. Concentrations of particulate matter of size lower than 10 μm (PM₁₀) were assessed in the highly urbanized Varanasi city situated in middle Indo-Gangetic plain of India from 2014 to 2017, to identify the distant air pollution sources based on trajectory statistical models and local sources by conditional bivariate probability function. Modifying effects of meteorology and air pollutants on PM₁₀ were also explored. Mean PM₁₀ concentration for the study period was 244.8 ± 135.8 μg m^?3, which was 12 times higher than the WHO annual guideline. Several distinct sources of traffic as the major source of PM₁₀ were identified in the city. Trajectory statistical models like cluster analysis, potential source contribution function and concentration-weighted trajectory showed significant contributions from north-west and eastern directions in the transport of polluted air masses to the city. Dew point, wind speed, temperature and ventilation coefficient are the major factors in PM₁₀ formation and dispersion.     

The pollution characteristics of PM<Subscript>2.5</Subscript> and correlation analysis with meteorological parameters in Xinxiang during the Shanghai Cooperation Organization Prime Ministers’ Meeting

The pollution characteristics of PM_2.5 and correlation analysis with meteorological parameters in Xinxiang during the Shanghai Cooperation Organization Prime Ministers’ Meeting were investigated. During the whole meeting, nine PM_2.5 samples were collected at a suburban site of Xinxiang, and the average concentration of PM_2.5 was 122.28 μg m^?3. NO₃ ^?, NH₄ ⁺, SO₄ ^2? accounted for 56.8% of the total water-soluble ions. In addition, with an exception of Cl^?, all of water-soluble ions decreased during the meeting. Total concentrations of crustal elements ranged from 6.53 to 185.86 μg m^?3, with an average concentration of 52.51 μg m^?3, which accounted for 82.5% of total elements. The concentrations of organic carbon and elemental carbon were 7.71 and 1.52 μg m^?3, respectively, lower than those before and after the meeting. It is indicated that during the meeting, limiting motor vehicles is to reduce exhaust emissions, delay heating is to reduce the fossil fuel combustion, and other measures are to reduce the concentration of PM_2.5. The directly dispersing by mixing layerheight increase and the indirectly reducing the formation of secondary aerosol by low relative humidity, andthese are the only two key removing mechanisms of PM_2.5 in Xinxiang during the meeting.     

Exposure assessment,chemical characterization and source identification of PM2.5 for school children and industrial downwind residents in Guangzhou,China

To assess the exposure doses of PM_2.5 and to investigate its chemical components for the subpopulation (i.e., school children and industrial downwind residents), simultaneous sampling of indoor and outdoor PM_2.5 was conducted at an elementary school close to traffic arteries and a residence located in the downwind area of a steel plant in metropolitan Guangzhou in 2010. Chemical components, i.e., organic carbon, elemental carbon and 6 water soluble ions were analyzed in PM_2.5. A survey was also conducted to investigate the time-activity patterns of the school children and the industrial downwind residents. Indoor and outdoor PM_2.5 were 63.2 ± 20.1 and (76.7 ± 35.8) μg/m³ at the school, and 118.8 ± 44.7 and 125.7 ± 57.1 μg/m³ in the community, respectively. Indoor PM_2.5 was found to be highly related to outdoor sources, and stationary sources were the significant contributors to PM_2.5 at both sites. The daily average doses of PM_2.5 for the school children at the school (D _children) and the industrial downwind residents in the community (D _residents) were (7.6 ± 1.9) and (36.1 ± 36.8) μg/kg-day, respectively. The daily average doses of particulate organic mass and SO₄ ^2? were the two most abundant chemical components in PM_2.5. PM_2.5 exposure for the school children was contributed by indoor and outdoor environments by 48.8 and 51.2 %, respectively; for the industrial downwind residents, the contributions were 66.0 and 34.0 %, respectively. Age and body weight were significantly and negatively correlated with D _children, while age, body weight and education level were significantly and negatively correlated with D _residents; gender was not a significant factor at both cases.     

Oxidative potential (OP) and mineralogy of iron ore particulate matter at the Gol-E-Gohar Mining and Industrial Facility (Iran)

Concentrations of total suspended particulate matter, particulate matter with aerodynamic diameter <2.5 μm (PM_2.5), particulate matter <10 μm (PM₁₀), and fallout dust were measured at the Iranian Gol-E-Gohar Mining and Industrial Facility. Samples were characterized in terms of mineralogy, morphology, and oxidative potential. Results show that indoor samples exceeded the 24-h PM_2.5 and PM₁₀ mass concentration limits (35 and 150 µg m^?3, respectively) set by the US National Ambient Air Quality Standards. Calcite, magnetite, tremolite, pyrite, talc, and clay minerals such as kaolinite, vermiculite, and illite are the major phases of the iron ore PM. Accessory minerals are quartz, dolomite, hematite, actinolite, biotite, albite, nimite, laumontite, diopside, and muscovite. The scanning electron microscope structure of fibrous-elongated minerals revealed individual fibers in the range of 1.5 nm to 71.65 µm in length and 0.2 nm to 3.7 µm in diameter. The presence of minerals related to respiratory diseases, such as talc, crystalline silica, and needle-shaped minerals like amphibole asbestos (tremolite and actinolite), strongly suggests the need for detailed health-based studies in the region. The particulate samples show low to medium oxidative potential per unit of mass, in relation to an urban road side control, being more reactive with ascorbate than with glutathione or urate. However, the PM oxidative potential per volume of air is exceptionally high, confirming that the workers are exposed to a considerable oxidative environment. PM released by iron ore mining and processing activities should be considered a potential health risk to the mine workers and nearby employees, and strategies to combat the issue are suggested.     

Source identification of particulate matter and associated intake of elements through inhalation in an industrial area of Odisha,India

Particulate matter concentrations were measured in an industrial region in the Ganjam district of Odisha. The average levels of suspended particulate matter (SPM) were measured to be 142 ± 8 and PM₁₀ of particulate matter with a size of less than 10 micrometers (PM₁₀) to be 50 ± 15 μg m^?3. Out of the 14 elements determined, Ca, Na, Mg, Fe, and K contributed more than 95% of the total weight. In enrichment factors, the trace elements, i.e., Zn, Pb, Cd, and Hg were observed to be highly enriched in the SPM and PM₁₀. Factor analysis indicates that more than 75% of the variance was due to five component factors, which have eigenvalues greater than 1. Intake of elements through inhalation route to adults has been estimated.     

Trace element concentration in fine particulate matter (PM<Subscript>2.5</Subscript>) and their bioavailability in different microenvironments in Agra,India: a case study

Exposure to airborne particulate matter results in the deposition of millions of particle in the lung; consequently, there is need for monitoring them particularly in indoor environments. Case study was conducted in three different microenvironments, i.e., urban, rural and roadside to examine the elemental bioavailability in fine particulate matter and its potential health risk. The samples were collected on polytetrafluoroethylene filter paper with the help of fine particulate sampler during August–September, 2012. The average mass concentration of PM_2.5 was 71.23 µg m^?3 (rural), 45.33 µg m^?3 (urban) and 36.71 µg m^?3 (roadside). Elements in PM_2.5 were analyzed by inductively coupled plasma atomic emission spectroscopy. Percentage bioavailability was determined to know the amount of soluble fraction that is actually taken across the cell membrane through inhalation pathway. Cadmium and lead were found to have cancer risk in a risk evaluation using an Integrated Risk Information system.     

Modelling concentrations of airborne primary and secondary PM10 and PM2.5 with the BelEUROS-model in Belgium

The Eulerian Chemistry-Transport Model BelEUROS was used to calculate the concentrations of airborne PM₁₀ and PM_2.5 over Europe. Both primary as well as secondary particulate matter in the respirable size-range was taken into account. Especially PM_2.5 aerosols are often formed in the atmosphere from gaseous precursor compounds. Comprehensive computer codes for the calculation of gas phase chemical reactions and thermodynamic equilibria between compounds in the gas-phase and the particulate phase had been implemented into the BelEUROS-model. Calculated concentrations of PM₁₀ and PM_2.5 are compared to observations, including both the spatial and daily, temporal distribution of particulate matter in Belgium for certain monitoring locations and periods. The concentrations of the secondary compounds ammonium, nitrate and sulfate have also been compared to observed values. BelEUROS was found to reproduce the observed concentrations rather well. The model was applied to assess the contribution of emissions derived from the sector agriculture in Flanders, the northern part of Belgium, to PM₁₀- and PM_2.5-concentrations. The results demonstrate the importance of ammonia emissions in the formation of secondary particulate matter. Hence, future European emission abatement policy should consider more the role of ammonia in the formation of secondary particles.     

Dependency of polycyclic aromatic hydrocarbon concentrations on particle size distribution in Tehran atmosphere

In this work, the airborne particulate matter with an aerodynamic diameter less than 10 µm (PM₁₀) was fractionated in a six-stage high-volume cascade impactor to identify particulate size distribution in Tehran atmosphere. The study was conducted at 15 sites located in the north, south, east, west, and central parts of Tehran in 2005. Air samples were analyzed for 16 polycyclic aromatic hydrocarbons (PAHs) by HPLC. The daily PM₁₀ concentrations at the peak of traffic in roadside areas were found to be 106–560 µg m^?3. The cumulated concentration sum of PAHs, based on 16 species, was found to have an average concentration of 380 ng m^?3. Furthermore, it was found that more than 60% of PAHs belonged to the small particulate size range, having sizes of less than 0.49 µm, some containing benzo(ghi)perylene and indeno(123cd)pyrene (high molecular weight) with average concentrations of 8 and 6 ng m^?3 and fluorene, phenanthrene, and fluoranthene (low molecular weight) with average concentrations of 14, 13, and 19 ng m^?3, respectively. In addition, the results revealed that the lighter three- and four-ring PAH compounds were the most abundant pollutants in the air collected at all the sampling sites.     

Atmospheric particulates and human health: Potential occupational health implications of working in an archaeologically and economically important cave in southeast Asia

The Niah Great Cave contains important archaeological artefacts immersed in massive guano deposits. The exposure of such artefacts, together with general movement through the cave, results in an enhanced atmospheric particulate pollution. Values, as a consequence of disturbance, are as high as 1300?µg/m³; alarming PM₁₀ values of 1051?µg/m³ are reported and potential human health effects in terms of particulate lung penetration, enhanced asthma susceptibility, heart disease and mortality are reviewed and discussed.     

Platinum in PM2.5 of the metropolitan area of Mexico City

The increase in platinum (Pt) in the airborne particulate matter with size ≤2.5 µm (PM_2.5) in urban environments may be interpreted as result of the abrasion and deterioration of automobile catalyst. Nowadays, about four million vehicles in Mexico City use catalytic converters, which means that their impact should be considered. In order to evaluate the contribution of Pt to environmental pollution of the metropolitan area of Mexico City (MAMC), airborne PM_2.5 was collected at five different sites in the urban area (NW, NE, C, SW, SE) in 2011 during April (dry-warm season), August (rainy season) and December (dry-cold season). Analytical determinations were carried out using a ICP-MS with a collision cell and kinetic energy discrimination. The analytical and instrument performance was evaluated with standard road dust reference material (BCR-723). Median Pt concentration in the analyzed particulate was is 38.4 pg m^?3 (minimal value 1 pg m^?3 maximal value 79 pg m^?3). Obtained Pt concentrations are higher than those reported for other urban areas. Spatial variation shows that SW had Pt concentration significantly higher than NW and C only. Seasonal variation shows that Pt median was higher in rainy season than in both dry seasons. A comparison of these results with previously reported data of PM₁₀ from 1991 and 2003 in the same studied area shows a worrying increase in the concentration of Pt in the air environment of MAMC.     

Water-soluble inorganic ions in airborne particulates from the nano to coarse mode: a case study of aerosol episodes in southern region of Taiwan

In 2004, airborne particulate matter (PM) was collected for several aerosol episodes occurring in the southern region of Taiwan. The particulate samples were taken using both a MOUDI (Micro-orifice Uniform Deposit Impactor) and a nano-MOUDI sampler. These particulate samples were analyzed for major water-soluble ionic species with an emphasis to characterize the mass concentrations and distributions of these ions in the ambient ultrafine (PM_0.1, diameter <0.1 μm) and nano mode (PM_nano, diameter <0.056 μm) particles. Particles collected at the sampling site (the Da-Liao station) on the whole exhibited a typical tri-modal size distribution on mass concentration. The mass concentration ratios of PM_nano/PM_2.5, PM_0.1/PM_2.5, and PM₁/PM_2.5 on average were 1.8, 2.9, and 71.0%, respectively. The peak mass concentration appeared in the submicron particle mode (0.1 μm < diameter <1.0 μm). Mass fractions (percentages) of the three major water-soluble ions (nitrate, sulfate, and ammonium) as a group in PM_nano, PM_0.1, PM₁, and PM_2.5 were 18.4, 21.7, 50.0, and 50.7%, respectively. Overall, results from this study supported the notion that secondary aerosols played a significant role in the formation of ambient submicron particulates (PM_0.1−1). Particles smaller than 0.1 μm were essentially basic, whereas those greater than 2.5 μm were neutral or slightly acidic. The neutralization ratio (NR) was close to unity for airborne particles with diameters ranging from 0.18 to 1 μm. The NRs of these airborne particles were found strongly correlated with their sizes, at least for samples taken during the aerosol episodes under study. Insofar as this study is exploratory in nature, as only a small number of particulate samples were used, there appears to be a need for further research into the chemical composition, source contribution, and formation of the nano and ultrafine mode airborne particulates.     

电镀企业周边大气颗粒物PM_(2.5)、PM_(10)和TSP中重金属分布特征及健康风险评价

以东莞市5个镇区为研究对象,采集电镀企业周边大气样品,分析了样品中重金属(包括As、Co、Cd、Cr、Cu、Mn、Ni、Pb、Sb、V、Zn和Hg)的含量分布,使用富集因子(enrich factor)、地累积指数(index of geoaccumulation)、Hakanson法和美国国家环境保护局(US EPA)的人体暴露健康风险评价模型,对PM_(2.5)、PM_(10)、总悬浮颗粒物(TSP)中重金属进行人体健康风险评价。结果表明,PM_(2.5)、PM_(10)和TSP中As、Cd和Cr平均浓度皆超标。Cr、Ni和V元素在3种颗粒物中非富集,主要为自然源;As、Co、Cu、Pb和Zn,可能来源于自然源和叠加的工业污染。Cd、Hg和Sb浓度受人为污染影响严重。Cd、Sb、Cu、Zn、Pb为生物可利用元素(K>0.6),在环境中的可迁移性高且易于被生物体和人体吸收。Mn元素的非致癌风险值较其他重金属要高1~4个数量级,且儿童的非致癌暴露风险值HQ均高于成人的。3种颗粒物中重金属元素通过呼吸吸入途径产生的非致癌风险HI值均高于人体可接受的上限1.0,其主要贡献来源于Mn的影响,研究区非致癌风险较为严重。除PM_(10)中Co元素和TSP中Co、Cr的成人致癌风险CR值大于10-4之外,其余大部分重金属元素通过呼吸途径产生的致癌风险CR值均在可接受范围之内,此外,3种颗粒物中的成人的致癌暴露风险值CRT均高于儿童的CRT值,并且除了PM_(2.5)中儿童的重金属致癌暴露风险CRT值(4.70E-05)低于人体可接受范围的上限(10-4),其余CRT值均高于10-4,致癌风险较为严重。