Fume emissions during gas metal arc welding

The control of exposure to welding fumes is of increasing importance in promoting a healthy, safe and productive work environment. This article describes the effects of shielding gas composition on the amount and composition of welding fumes produced during gas metal arc welding (GMAW). The amount of fumes generated during welding was measured for steady current over a range of wire-feed speeds and arc voltages using the standard procedures contained in ANSI/AWS F1.2 [American Welding Society. ANSI/AWS F1.2. Laboratory method for measuring fume generation rates and total fume emission of welding and allied processes. Miami, Florida; 1992]. Results of these measurements show that the fume formation rates (FFRs) increase with CO₂ and O₂ in the shielding gas mixture. The lowest FFRs were obtained with the mixtures of Ar?+?2%CO₂ and Ar?+?3%CO₂?+?1%O₂. The highest FFRs were obtained with the mixtures of Ar?+?18%CO₂ and Ar?+?5%CO₂?+?4%O₂. The welding fumes contains mainly iron, manganese, silicon, titanium and sodium under oxide forms. The fume cluster particles have dimensions between 0.5 and 2?µm. The FFR was found to be governed by the transfer modes of molten metal, i.e. the current intensity and arc voltage, as well as by the shielding gas mixtures composition. Thus these parameters have to be taken into consideration before designing a welding process. Whenever possible, users of GMAW should use the lowest current intensity. However, when this is not possible, due to the constraints of process productivity, welders should use higher currents, but with Ar?+?2%CO₂ and Ar?+?3%CO₂?+?1%O₂ shielding mixtures, which will lead to smaller fume emissions.     

电炉烟尘治理方法的选择和经济比较

就电炉炼钢过程产生的烟尘污染特点进行了综述，并就各类方法的技术经济指标进行了比较。     

煤气发生炉在工业炉窑烟气治理中的应用

文章介绍了煤气发生炉在工业炉窑烟气治理中的应用,从减少环境污染和节能降耗两个方面客观实际地分析了不同的煤气发生炉在各种窑炉应用中的特点,对典型性和普遍性的内容予以概括,希望起到抛砖引玉的作用,以利用工业炉窑烟气治理工程的开展。     

A state of the science review of the potential health hazards associated with asbestos in shielded metal arc welding rods in the United States

Due to its unique chemical properties, chrysotile asbestos was historically incorporated into a wide variety of products, including the outer covering, or “flux” of certain classifications of general arc mild steel welding electrodes. The purpose of this analysis is to review the historical engineering, toxicology, regulatory, and epidemiology information relevant to asbestos in mild steel welding rods in order to assess whether mild steel welders are at increased risk of developing asbestos-related diseases as a result of welding rod use. We divided our analysis into four distinct time periods, based on what we perceived to be seminal events in welding technology or in the evolution of knowledge regarding asbestos and asbestos-related diseases. These time periods are as follows: late 1800s to 1929, 1930–1955, 1956–1970, and 1971–2006. We found that studies that attempted to measure airborne asbestos directly in welding rod fumes found no measurable fibers; this is likely due to the fact that the fibers degrade at high temperatures present in the welding arc. In addition, “worst-case” use simulation studies, specifically intended to generate airborne flux particles, reported that airborne asbestos concentrations were either undetectable or very low. The airborne concentrations generated were always below the current OSHA permissible exposure limit (0.1 f/cc TWA), and the lifetime doses associated with “worst-case” use were found to be far below the plausible thresholds for mesothelioma and lung cancer. The epidemiology of mild steel welders is difficult to interpret due to confounding exposures such as (1) possible exposure to nickel and hexavalent chromium in stainless steel welding fumes (lung cancer), (2) smoking (lung cancer), and (3) bystander exposure to amphibole asbestos (lung cancer and mesothelioma). None of the published welder studies controlled for all three factors, yet when any single source of bias was controlled for, the majority of the studies reported no significant risk in either asbestos-related disease. Furthermore, none of the investigators in any of the welder studies suggested that asbestos in welding rods might be a risk factor for lung cancer or mesothelioma, and there is not a single case report in the medical literature that attempts to link welding rod use to an asbestos-related disease. We conclude that the weight of evidence indicates that welders were not historically at risk of developing asbestos-related diseases as a result of welding rod use.     

Health risk assessment and oxidative stress in workers exposed to welding fumes

The aim of this study was designed to determine the influence of welding fumes on oxidative stress in humans and the role of metals. A questionnaire was designed to collect information regarding personal characteristics, including age, weight, height, and medical history; life style such as smoking status and exercise habits; and occupational history such as working history, working environment, employment duration, and use of protective equipment. Body mass index (BMI) in kg/m² was then calculated for each participant. Blood samples were also drawn to determine malondialdehyde (MDA) levels and various metals in plasma. Significantly higher plasma MDA (4.08 µg/L) was observed as compared to controls (1.61 µg/L). Blood metal analysis also showed elevated level of metals in welders for cadmium, chromium, lead,and nickel. Data indicated that workers occupationally exposed to welding fumes for prolong periods possessed higher metal levels associated with increased oxidative stress as evidenced by elevated MDA levels.     

Printed in great Britain Cr(VI) and other metallic mutagens in fly ash and welding fumes†

Particulate samples taken from both the indoor (working) and outdoor (community) environments contain a wide range of metallic trace elements most of which are mutagenic in at least one of the short term tests for genotoxicity currently in use. Because of the demonstrated presence of a short lived biologically active species (Cr(VI)), and the uncertainty with which the results of the screening of metallic compounds in short term tests can be interpreted in terms of human risk, great care must be taken to assure the appropriate collection, storage, and chemical and biological assay of such material. The sensitivity of the results for fly ash and welding fumes to variations in these protocols is demonstrated and discussed.     

Toxic responses of different organs following occupational exposure to sub-threshold limit value levels of paving asphalt fumes

The main purpose of this study was to ascertain whether occupational exposure to asphalt fumes, under normal working conditions, is associated with any hepatotoxic, nephrotoxic, or hematotoxic response. This was a cross-sectional study in which 210 subjects (80 exposed and 130 reference subjects) were investigated. Using standard methods, atmospheric concentrations of total particulate and benzene-soluble fractions of asphalt fumes were measured. Additionally, urine and blood samples were taken from subjects for complete blood count, white blood cell differential test, urinalysis, and routine biochemical tests of kidney and liver function. Both groups were similar as far as their demographic variables and smoking habits were concerned. The levels of exposure to total particulate and benzene-soluble fractions were estimated to be 0.9?±?0.2 and 0.32?±?0.09 mg m^?3, respectively (mean?±?SD), both of which being lower than the existing threshold limit values. Statistically, significant associations between exposure to asphalt fumes and changes in most liver and kidney function tests and complete blood count parameters provided circumstantial evidence in favor of the notion that exposure to sub-threshold limit value levels of total particulate and benzene-soluble fractions is associated with early liver and kidney dysfunction as well as hematological disorders.     

Carbon black-benzo(a)pyrene complex-induced apoptosis and autophagy blockage in rat alveolar macrophages

Abstract

Cooking of foods and the burning of biomass and fossil fuels in stoves are the main sources of cooking fumes, with carbon black and polycyclic aromatic hydrocarbons as main components. The toxicity of carbon black and polycyclic aromatic hydrocarbons has been well studied individually, but the combined toxicity is much less understood. Carbon black can adsorb benzo(a)pyrene to form a complex which displays an altered physical form which in this study has been constructed to simulate particles in the cooking fumes and explore the combined toxic effect on rat alveolar macrophages. The complex-induced cell apoptosis and blocked cell autophagy flux compared with both individually. The mechanism of toxicity may be by intracellular reactive oxygen species generation, impairing the mitochondrial membrane potential and activating apoptosis signaling pathways.     

Urinary 8-oxo-7, 8-dihydro-2′-deoxyguanosine concentrations after frying of bacon,a pilot study

Cooking fumes contain compounds that may give rise to oxidative stress and mutations when inhaled. The aim of this study was to evaluate if cooking fumes from frying of bacon induce oxidative stress by measurement of urinary 8-oxo-7,8-dihydro-2 deoxyguanosine, a marker of oxidatively damaged DNA. Three non-smoking women fried bacon for 3 h. Urine samples were taken as early morning void at the same time on four days; the morning before frying, the morning after first frying, the morning after three days of frying and one week after first urine sample. 8-Oxo-7,8-dihydro-2 deoxyguanosine, 1-hydroxypyrene and 2-hydroxyphenanthrene, metabolites of polycyclic aromatic hydrocarbons, were measured by liquid chromatography-mass spectrometry/mass spectrometry (LC-MS/MS). 8-Oxo-7,8-dihydro-2 deoxyguanosine correlated weakly with concentrations of 1-hydroxypyrene (r = 0.31, p = 0.042), but it did not correlate with 2-hydroxyphenanthrene (r = ?0.074; p = 0.64). Average urinary 8-oxo-7,8-dihydro-2 deoxyguanosine concentrations increased from the day before frying (16.3 ± 4.2 nmol/L) to the third day of frying (26.2 ± 10.2 nmol/L), although not statistically significantly. Our pilot study shows that frying of bacon may result in increased oxidative stress which further emphasises the possible carcinogenic potential of cooking fumes.     

Arsenic and fluoride in the groundwater of Mexico

Concentrations of arsenic and fluoride above Mexican drinking water standards have been detected in aquifers of various areas of Mexico. This contamination has been found to be mainly caused by natural sources. However, the specific processes releasing these toxic elements into groundwater have been determined in a few zones only. Many studies, focused on arsenic-related health effects, have been performed at Comarca Lagunera in northern México. High concentrations of fluoride in water were also found in this area. The origin of the arsenic there is still controversial. Groundwater in active mining areas has been polluted by both natural and anthropogenic sources. Arsenic-rich minerals contaminate the fractured limestone aquifer at Zimapán, Central México. Tailings and deposits smelter-rich fumes polluted the shallow granular aquifer. Arsenic contamination has also been reported in the San Antonio-El Triunfo mining zone, southern Baja California, and Santa María de la Paz, in San Luis Potosí state. Even in the absence of mining activities, hydrogeochemistry and statistical techniques showed that arsenopyrite oxidation may also contaminate water, as in the case of the Independencia aquifer in the Mexican Altiplano. High concentrations of arsenic have also been detected in geothermal areas like Los Azufres, Los Humeros, and Acoculco. Prevalence of dental fluorosis was revealed by epidemiological studies in Aguascalientes and San Luis Potosí states. Presence of fluoride in water results from dissolution of acid-volcanic rocks. In Mexico, groundwater supplies most drinking water. Current knowledge and the geology of Mexico indicate the need to include arsenic and fluoride determinations in groundwater on a routine basis, and to develop interdisciplinary studies to assess the contaminant's sources in all enriched areas.     

Mutagenic and carcinogenic effects of cadmium†

There is limited evidence to suggest that certain compounds of cadmium may be mildly mutagenic. Some compounds of cadmium have given rise to fibrosarcoma and rhabdomyosarcoma following subcutaneous or intramuscular injection in the rat and also to interstitial cell tumours of the testis as a sequel to cellular damage and testicular atrophy. Cadmium chloride aerosol inhalation has induced a high incidence of dose‐related lung cancer in the rat. Epidemiological observations suggest that mortality from prostatic and possibly from lung cancer has been increased in cadmium workers who had experienced the very high levels of cadmium, mainly as oxide dust or fume, which existed in the past. The more recent epidemiological studies have not added further evidence in support of the carcinogenic role of cadmium.     

Industries and lung cancer: A population-based case-control study in British Columbia

An investigation was conducted to identify high-risk industries for histological subtypes of lung cancer based on a large population-based case-control study in British Columbia, Canada. Occupational histories and information on smoking and relevant covariates were collected from 14,755 male incident cancer cases. Industrial risk factors for 2998 lung cancer cases, including histological subtypes were assessed by logistic regression using other cancer cases, excluding smoking-related cancers, as controls. An excess risk of lung cancer was found among workers in mining, metal manufacturing, and electric power systems for all histological-subtypes, and construction, water transport, health services for specific histological subtypes. Industrial associations that are unique to histological subtypes of lung cancer were identified. Future research needs to focus on confirming these histological associations, and identifying the risk from key exposures found within these industries (e.g. medical radiation, electromagnetic fields, and cooking fumes).     

循环流化床锅炉烟气脱硫除尘技术改造

对承德市热电厂CG35／3．82－MX型循环流化术锅炉的脱硫除尘系统进行了改造,解决了原水膜除尘器效率低,烟法排放严重超标的问题,取得了良好的环境效益,社会效益和经济效益。     

Low level inhalation experiments with four different cadmium compounds in rats†

This long‐term inhalation study was designed to describe the toxicity and the carcinogenic risk from Cd compounds because it had been shown from former long‐term inhalation studies that cadmium choloride induced primary lung tumors in Wistar rats. It was therefore logical to examine whether other cadmium compounds to which human beings are more frequently exposed have also carcinogenic potency. In a long‐term inhalation study cadmium aerosols consisting of cadmium chloride (CdCl₂), cadmium oxide (CdO) as dusts and fumes, cadmium sulfate (CdSO₄), cadmium sulfide (CdS) and a combination of cadmium oxide/zinc oxide were used. Wistar rats were continuously exposed in inhalation chambers for 18 months 22 hrs a day or for 40 hrs a week. The studies will be terminated at the mean survival life time of the species. The aerosols were generated by several different systems. The particles of the cadmium aerosols have the average mass medium diameters in the range from 0.2 to 0.5 μm.     

天津市大气主要污染物总量控制允许排放量实施方案

本文采用环境质量总量控制技术路线。在天津市建立了１８个总量控制区,利用箱扩散模型（Ａ值法）测算了各总控区二氧化硫的允许排放量。利用Ｐ值法将区域允排量分配到源。本文还将化学质量受体平衡（ＣＭＢ）模型纳入Ａ－Ｐ值模型,形成ＡＰ－ＣＭＢ模型,用以测算烟尘和工业粉尘的区域允排量将将分配到源。由此构成天津市大气主要污染物总量控制允排量实施方案。     

European Court of Justice ruling regarding new genetic engineering methods scientifically justified: a commentary on the biased reporting about the recent ruling

In July 2018, the European Court of Justice (Case C-528/16) ruled that organisms obtained by directed mutagenesis techniques are to be regarded as genetically modified organisms (GMOs) within the meaning of Directive 2001/18. The ruling marked the next round of the dispute around agricultural genetic engineering in Europe. Many of the pros and cons presented in this dispute are familiar from the debate around the first generation of genetic engineering techniques. The current wave of enthusiasm for the new genetic engineering methods, with its claim to make good on the failed promises of the previous wave, seems to point more to an admission of failure of the last generation of genetic engineering than to a true change of paradigm. Regulation is being portrayed as a ban on research and use, which is factually incorrect, and the judges of the European Court of Justice are being defamed as espousing “pseudoscience”. Furthermore, this highly polarised position dominates the media reporting of the new techniques and the court’s ruling. Advocates of the new genetic engineering techniques appear to believe that their benefits are so clear that furnishing reliable scientific evidence is unnecessary. Meanwhile, critics who believe that the institution of science is in a serious crisis are on the increase not just due to the cases of obvious documented scientific misconduct by companies and scientists, but also due to the approach of dividing the world into those categorically for or against genetic engineering. In this construct of irreconcilable opposites, differentiations fall by the wayside. This article is a response to this one-sided and biased reporting, which often has the appearance of spin and lacks journalistic ethics that require journalists to report on different positions in a balanced and factual manner instead of taking positions and becoming undeclared advocates themselves.     

Air quality and micro-meterological monitoring of gaseous pollutants/flame emissions from burning crude petroleum in poultry house

Air quality of gaseous emissions from crude petroleum flames and fumes were monitored in a poultry house at 10 min intervals; from 10.10am–11.10am daily for 14 days. The crude petroleum burning was simulated in a metal burner, 22.86 cm high with a diameter of 17.80 cm and a thickness of 1.27 cm designed for the purpose. The micro-climate (ambient temperature, relative humidity and light intensity) of the experimental environment (poultry houses) was recorded. Results showed that the mean gaseous pollutants emitted before and during the experiments varied within the poultry house. Gases such as sulphur dioxide (SO₂), hydrogen sulphide (H₂S), methane(CH₄) and carbon monoxide (CO) were higher in the brooding than finishing phase, while volatile organic carbon (VOC) and suspended particulate matter (SPM) levels were lower at the brooding than finishing phase. The values obtained in this study for 60 min (at 10 min intervals) are far higher than the values elucidated by the Federal Environmental Protection Agency, which are outdoor air quality measurements as compared to those in this study measured indoors.     

Lyme Disease and Conservation

Lyme disease is a tick-borne illness that is widespread in North America, especially in the northeastern and northcentral United States. This disease could negatively influence efforts to conserve natural populations in two ways: (1) the disease could directly affect wild animal health; and (2) tick control efforts could adversely affect natural populations and communities. Lyme disease affects several domestic animals, but symptoms have been reported in only a few wild species. Direct effects of Lyme disease on wild animal populations have not been reported, but the disease should be considered as a possible cause in cases of unexplained population declines in endemic areas. Methods available to manage ticks and Lyme disease include human self-protection techniques, manipulation of habitats and host species populations, biological control, and pesticide applications. The diversity of available techniques allows selection of approaches to minimize environmental effects by (1) emphasizing personal protection techniques, (2) carefully targeting management efforts to maximize efficiency, and (3) integrating environmentally benign techniques to improve management while avoiding broad-scale environmentally destructive approaches. The environmental effects of Lyme disease depend, to a large extent, on the methods chosen to minimize human exposure to infected ticks. Conservation biologists can help design tick management programs that effectively lower the incidence of human Lyme disease while simultaneously minimizing negative effects on natural populations.     

Hormonal responses of broiler chickens to simulated crude petroleum flame and fumes

Hormonal responses of broiler chickens exposed to crude petroleum flame and fumes at varying distances over a period of 16 h daily were evaluated for 56 days in a poultry house. The burning of crude petroleum was simulated in a designed burner. The measured distances were 4, 8, or 12 m from the flame point. The experimental design was a two-factor factorial in a completely randomized design (CRD) with factor A as distance from the crude petroleum flame and factor B was the age of birds in weeks. One hundred and eighty Anak day-old broiler chickens were divided into four groups of 45 birds each, replicated thrice at 15 birds per replicate. Control birds were located in a separate poultry building without the flame treatment. Gaseous emissions from the burning crude oil were monitored. Proprietary broiler starter and finisher diets were fed ad libitum. Blood samples were taken at the fourth and eighth week for hormone radioimmunoassay from each treatment. The hormones assayed were growth hormone (GH), thyroxine (T₄,), and adrenaline. Results indicated that treatments did not significantly alter hormonal levels. The age of birds significantly affected the levels of all three hormones measured.     

Biodegradation of crude petroleum and petroleum products by fungi isolated from two oil seeds (melon and soybean)

Crude petroleum oil degrading fungi were isolated from two oil seeds, Cucumeropsis mannii (melon) and Glycine max (soybean) seeds in the presence and absence of petroleum fumes. An assessment of the relative ability of each fungus to degrade crude petroleum, diesel and kerosene on minimum salt solution was done using change in optical density read on spectrophotometer. Twenty-one fungal species (14 genera) were isolated altogether during this experiment. These include eight species of Aspergillus; one species each of Botryodiplodia, Bipolaris, Cladosporium, Cunnighamella, Dreschlera, Fusarium, Helminthosporium, Macrophomina, Mucor, Paeciliomyces, Penicillium, Rhizopus and Talariomyces. It was evident that most of the fungi tested were able to biodegrade the crude petroleum oil, though at different rates. Bipolaris had a low rate of biodegradation of the petroleum oil of all the fungal species isolated Botryodiplodia theobromae had the highest degrading ability on the crude oil, while Aspergillus flavus had the least after 40 days of incubation. Aspergillus flavus had the highest ability to biodegrade diesel while A. niger had the least ability. In kerosene, Macrophomina phaseolina had the highest ability while A. niger had the least ability to biodegrade it. There was fluctuation in the growth pattern of the fungi in the petroleum oil medium. The implication of these are discussed.