Adsorptive removal of rhodamine B from textile wastewater using water chestnut (Trapa natans L.) peel: adsorption dynamics and kinetic studies

Water chestnut peel, an agricultural bio-waste, was used as a biosorbent for removal of rhodamine B (RhB), basic textile dye, from an aqueous solution. The effects of various experimental parameters were studied. The equilibrium data correlated well with a Freundlich isotherm (R² = 0.98–0.99) followed by a Halsey isotherm model (R² = 0.98–0.99) which indicated heterogeneity of the adsorbent surface and multilayer adsorption of RhB dye onto the water chestnut peel waste (WCPW). High correlation coefficients (R² = 0.99) together with close agreement between experimental q_e (0.4–1.7 mg g^?1) and calculated q_e (0.4–2.5 mg g^?1) suggested that the adsorption process followed pseudo-second-order kinetics, with k₂ values in the range of 52–3.4 × 10^?1 g mg^?1 min^?1 at different concentrations. The overall mechanism of adsorption was controlled by both liquid-film and intra-particle diffusions. The negative values of change in Gibb's free energy (?ΔG⁰ = 19.2–29.2 kJ mol^?1) and positive values of change in enthalpy (ΔH⁰ = 30.9–117.6 kJ mol^?1) revealed the process to be spontaneous and endothermic. WCPW was found to be an effective adsorbent for removal of RhB, a cationic dye, from an aqueous solution.     

Removal of cadmium(II), lead(II), and chromium(VI) ions from aqueous solution using clay

Removal of cadmium(II), lead(II), and chromium(VI) from aqueous solution using clay, a naturally occurring low-cost adsorbent, under various conditions, such as contact time, initial concentration, temperature, and pH has been investigated. The sorption of these metals follows both Langmuir and Freundlich adsorption isotherms. The magnitude of Langmuir and Freundlich constants at 30°C for cadmium, lead, and chromium indicate good adsorption capacity. The kinetic rate constants (K _ad) indicate that the adsorption follows first order. The thermodynamic parameters: free energy change (ΔG ^o), enthalpy change (ΔH ^o), and entropy change (ΔS ^o) show that adsorption is an endothermic process and that adsorption is favored at high temperature. The results reveal that clay is a good adsorbent for the removal of these metals from wastewater.     

Low-cost and efficient adsorbent derived from pyrolysis of Jatropha curcas seeds for the removal of Cu2+ from aqueous solutions

Biochar, is a low-cost material that can be used as an alternative adsorbent for the removal of heavy metals. In this study, a low-cost and efficient adsorbent synthesised from Jatropha curcas seeds was used for the uptake of Cu²⁺ from aqueous solutions. The as-prepared adsorbent was characterised by scanning electron microscopy and Brunauer–Emmett–Teller analysis post calcination at 500 °C, its BET surface area and total pore volume were 39.62?m²?g^?1 and 0.049?m³?g^?1, respectively. Subsequently, the effects of initial pH of the solution, contact time, and adsorbent material dosage on the adsorption of Cu²⁺ by the prepared adsorbent were investigated. The as-prepared adsorbent exhibited a high performance, with a maximum adsorption amount of 32.895?mg?g^?1 for Cu²⁺ at pH 5.0 and 25 °C, owing to the presence of ?OH, C=O, C–O, Si-O-Si, and O-Si-O on its surface. The predominant Cu²⁺ adsorption mechanism was assumed to be ion exchange. Notably, the Cu²⁺ adsorption could attain equilibrium within 90?min. In addition, the fact that the Langmuir model was a better fit than the Freundlich model for the isotherm data of Cu²⁺ adsorption by the as-prepared adsorbent suggested that the adsorption of Cu²⁺ was a monolayer adsorption process.     

Removal of selenite using ‘waste’ Fe(III)/Cr(III) hydroxide: Adsorption kinetics and isotherms

Removal of selenite [Se (IV)] from aqueous solution on to industrial solid ‘waste’ Fe(III)/Cr(III) hydroxide as adsorbent was investigated in the present article. Maximum adsorption was found to be at pH 4.0. Pretreated Fe(III)/Cr(III) hydroxide was found to be more efficient for the removal of selenite compared to untreated adsorbent. Langmuir and Freundlich isotherms have been studied. The Langmuir adsorption capacity (Q ₀) of the pretreated and untreated adsorbents was found to be 15.63 and 6.04?mg?g^?1, respectively. The adsorption process fit into the second-order kinetics. Thermodynamic parameters show that the adsorption process is spontaneous and endothermic in the temperature range 32 to 60°C. Coexisting anions vanadate and phosphate significantly affect the adsorption of selenite for both the pretreated and untreated adsorbents. Molybdate, thiocyanate, sulphate, nitrate and chloride do not significantly affect the removal of selenite for pretreated adsorbent.     

Removal of heavy metals from aqueous solutions using activated carbon prepared from Cicer arietinum

Removal of Cu²⁺, Cd²⁺, Pb²⁺, and Zn²⁺ from aqueous solutions by activated carbon prepared from stems and seed hulls of Cicer arietinum, an agricultural solid waste, has been studied. The influence of various parameters, such as pH, contact time, adsorbent dose, and initial concentration of metal ions on removal was evaluated. The activated carbon was characterized by FT-IR spectroscopy, X-ray diffraction, and elemental analysis. Sorption isotherms were studied using Langmuir and Freundlich isotherm models. All experimental sorption data were fitted to the sorption models using nonlinear least-squares regression. The maximum adsorption capacity values for activated carbon prepared from Cicer arietinum waste for metal ions were 18 mg g^?1 (Cu²⁺), 18 mg g^?1 (Cd²⁺), 20 mg g^?1 (Pb²⁺), and 20 mg g^?1 (Zn²⁺), respectively. The Freundlich isotherm model fit was best, followed by the pseudo-second-order kinetic model. Desorption studies were carried out with dilute hydrochloric acid for quantitative recovery of the metal ions and for regeneration of the adsorbent.     

Ackee apple (Blighia sapida) seeds: a novel adsorbent for the removal of Congo Red dye from aqueous solutions

The ability of ackee apple (AA) seeds to remove Congo Red (CR) dye from aqueous solution was investigated. AA was characterised using thermo gravimetric analyser, scanning electron microscopy, Braunauer Emmett Teller, pH_pzc, elemental analysis and Boehm titration. The effects of operational parameters such as adsorbent dosage, contact time, initial dye concentration and solution pH were studied in a batch system. pH has a profound influence on the adsorption process. Maximum dye adsorption was observed at pH 3.0. The reaction was fast, reaching equilibrium in 90 min. Adsorption data were best described by Langmuir isotherm and the pseudo-second-order kinetic model with a maximum monolayer coverage of 161.89 mg·g^?1. Both boundary layer and intraparticle diffusion mechanisms were found to govern the adsorption process. Thermodynamic parameters such as standard free energy change (Δ G ⁰), standard enthalpy change (Δ H ⁰), and standard entropy change (Δ S ⁰) were studied. Values of Δ G ⁰ varied between?30.94 and?36.56 kJ·mol^?1, Δ H ⁰ was 25.61 kJ·mol^?1, and Δ S ⁰ was 74.84 kJ·mol^?1·K^?1, indicating that the removal of CR from aqueous solution by AA was spontaneous and endothermic in nature. Regeneration and reusability studies were carried out using different eluents. AA gave the highest adsorption efficiency up to four cycles when treated with 0.3 M HCl. AA was found to be an effective adsorbent for the removal of CR dye from aqueous solution.     

Adsorptive features of banana (Musa paradisiaca) stalk-based activated carbon for malachite green dye removal

Chemically prepared activated carbon derived from banana stalk (BSAC) was used as an adsorbent to remove malachite green (MG) dye from aqueous solution. BSAC was characterised using thermogravimetric analyser, Brunauer Emmett Teller, Fourier transform infrared spectrometry, scanning electron microscopy, pH_pzc, elemental analysis and Boehm titration. The effectiveness of BSAC in adsorbing MG dye was studied as a function of pH, contact time, temperature, initial dye concentration and repeated desorption–adsorption processes. pH_pzc of BSAC was 4.5 and maximum dye adsorption occurred at pH 8.0. The rate of dye adsorption by BSAC was very fast initially, attaining equilibrium within 120 min following a pseudo-second-order kinetic model. Experimental data were analysed by Langmuir, Freundlich and Dubinin–Raduschevich isotherms. Equilibrium data fitted best into the Langmuir model, with a maximum adsorption capacity of 141.76 mg·g^?1. Δ G ⁰ values were negative, indicating that the process of MG dye adsorption onto BSAC was spontaneous. The positive values of Δ H ⁰ and Δ S ⁰ suggests that the process of dye adsorption was endothermic. The regeneration efficiency of spent BSAC was studied using 0.5 M HCl, and was found to be in the range of 90.22–95.16% after four cycles. This adsorbent was found to be both effective and viable for the removal of MG dye from aqueous solution.     

Immobilized Lentinus edodes residue as absorbent for the enhancement of cadmium adsorption performance

To investigate the potential use of Lentinus edodes (L. edodes) residue for Cd²⁺ adsorption, poly alcohol Na alginate (PVA) was applied to immobilize it. The parameters including contact time, pH, adsorbent dosages, and coexisting metal ions were studied. The suitable pH for immobilized L. edodes was 4?C7 wider than that for raw L. edodes (pH 6?C7). In the presence of Pb²⁺ concentration varying from 0 to 30 mg·L^?1, the Cd²⁺ adsorption ratios declined by 6.71% and 47.45% for immobilized and raw L. edodes, respectively. While, with the coexisting ion Cu²⁺ concentration varied from 0 to 30 mg·L^?1, the Cd²⁺ adsorption ratios declined by 12.97% and 50.56% for immobilized and raw L. edodes, respectively. The Cd²⁺ adsorption isotherms in single-metal and dual-metal solutions were analyzed by using Langmuir, Freundlich, and Dubinin-Radushkevich models. The Cd²⁺ adsorption capacities (q _m) in single-metal solution were 6.448 mg·L^?1 and 2.832 mg·L^?1 for immobilized and raw L. edodes, respectively. The q _m of immobilized L. edodes were 1.850 mg Cd·g^?1 in Cd²⁺ + Pb²⁺ solution and 3.961 mg Cd·g^?1 in Cd²⁺ + Cu²⁺ solution, respectively. The Cd²⁺ adsorption processes subjected to both adsorbents follow pseudo-second-order model. Mechanism study showed the functional group of L. edodes was -OH, -NH, -CO, and PVA played an important role in metal adsorbing. Mining wastewater treatment test showed that PVA-SA-immobilized L. edodes was effective in mixed pollutant treatment even for wastewater containing metal ions in very low concentration.     

Adsorption of phosphate ions from water using a novel cellulose-based adsorbent

A novel cellulose-based adsorbent, iron(III)-coordinated amino-functionalised poly(glycidylmethacrylate)-grafted cellulose [Fe(III)–AM-PGMACell] was developed for the removal of phosphate from water and wastewater. The scanning electron micrograph showed that AM-PGMACell has a rougher surface than cellulose and the adsorption of Fe(III) on AM-PGMACell made the surface even rougher. Infrared spectroscopy revealed that amino groups on the surface of AM-PGMACell complexed with Fe(III) played an important role in the removal of phosphate from solutions. X-Ray diffraction patterns showed a decrease in crystallinity after graft copolymerisation onto cellulose. The effects of contact time, initial sorbate concentration, pH, agitation speed, dose of adsorbent and temperature on the removal process were investigated. Maximum removal of 99.1% was observed for an initial concentration of 25 mg·L ^?1 at pH 6.0 and an adsorbent dose of 2.0 g·L ^?1. A two-step pseudo-first-order kinetic model and Sips isotherm model represented the measured data very well. Complete removal of 11.6 mg·L ^?1 phosphate from fertiliser industry wastewater was achieved by 1.6 g·L ^?1 Fe(III)–AM-PGMACell. The adsorbent exhibited very high reusability for several cycles. Overall, the study demonstrated that Fe(III)–AM-PGMACell can be used as an efficient adsorbent for the removal and recovery of phosphate from water and wastewater.     

Trichoderma harzianum: a green sorbent for Pb(II) uptake from aqueous solutions

This investigation describes the use of specially cultivated, nonliving biomass of Trichoderma harzianum as a biosorbent for the batch removal of Pb(II) from a stirred system under different experimental conditions. The metal removal depended upon pH, sorbent particle size, initial Pb(II) concentration, shaking speed, and sorption time. The optimal experimental conditions for the removal of Pb(II) by T. harzianum with an initial metal concentration of 100 mg L^?1 were obtained at a particle size of 53 μm, a pH of 4.5, a shaking speed of 200 rpm, and a contact time of 720 min. The results were analyzed in terms of adsorption isotherms and kinetic models. The Freundlich isotherm model and pseudo second-order model fitted well in the data. T. harzianum proved to be a good biomaterial for accumulating Pb(II) from aqueous solutions (q = 460 mg g^?1).     

Biosorption of cadmium and nickel ions using marine macrophyte,Cymodocea nodosa

ABSTRACT

Seagrass (Cymodocea nodosa) ability to remove cadmium and nickel ions from single metal solutions was investigated in the present study. Metal ions were measured in the solution using an atomic absorption spectrophotometer. Various operational parameters (initial pH, biomass dose, metal ion concentration, and contact time) were tested and found to affect the uptake capacity of Cd (II) and Ni (II). More than 70% of biosorption capacity occurred in the first few minutes for both metal ions. The pseudo-second-order kinetic model and the Langmuir model were found to best fit the experimental data of Cd (II) and Ni (II) biosorption. The maximum uptake capacity (q_max) was 11.6 and 16.7?mg.g^?1 for Cd (II) and Ni (II), respectively. The biosorbent was characterised using Fourier transform infrared spectrometry (FTIR), scanning electron microscope (SEM), and energy-dispersive X-ray spectroscopy (EDX). The infrared spectrum demonstrated that hydroxyl, carboxyl, and phenolic functional groups are the major binding sites for Cd (II) and Ni (II) metals. The ion exchange mechanism plays an important role during biosorption process as shown in EDX analysis. Our results conclude that marine macrophyte C. nodosa can be used as a low-cost biosorbent for the removal of Cd (II) and Ni (II) in wastewater.     

Preparation of magnetic nanocomposite beads and optimizing the conditions for effective removal of U(VI) from aqueous solutions

Magnetic ion-imprinted polymers (IIPs) were prepared by precipitate polymerization and leached with HCl to remove uranium. Their ability to remove hexavalent uranium from wastewater effluents was studied. Batch adsorption studies to determine the optimum conditions of U(VI) removal were conducted at different levels of sample pH, sorbent amount, agitation time, and initial uranium concentration. It was observed that, under optimum conditions (i.e. pH 4, adsorbent amount of 50 mg, 45 min agitation time, and initial U(VI) concentration of 2 mg L^?1), the maximum removal of U(VI) cations was >98% and 80% for the magnetic IIP and the corresponding magnetic non-imprinted polymers (NIP), respectively. Langmuir and Freundlich isotherms were used to describe the adsorption of U(VI) onto magnetic IIP and NIP. The adsorption capacity of U(VI) was determined to be 1.06 and 0.85 mg g^?1 for the two isotherms, respectively. The order of selectivity was found to be U(VI) > Fe(III) > Pb(II). For six cycles of regeneration and reuse, the magnetic polymers maintained their stabilities with only a 4% loss in the extraction efficiency. The average extraction efficiencies of the magnetic polymers for the spiked acid mine drainage and sewage wastewater effluents were 71% and 58% for the magnetic IIP and NIP, respectively. From powder X-ray diffraction analysis, application of the Scherrer equation yielded magnetic nanoparticles of an average mean diameter of 11.9 nm. Thermo-gravimetric analysis revealed that the HCl-leached magnetic polymers had a magnetite residual weight of 5%.     

Removal of C.I. acid brown 75 from aqueous solution by kaolinite

The adsorption of acid brown 75 onto kaolinite in aqueous solution was studied with respect to the pH, adsorbent dosage, contact time, initial concentration, and operating temperature. Desorption of dye from dye-saturated kaolinite was observed. Experimental data indicated that the adsorption capacity of kaolinite for the dye was higher in acidic rather than in basic solution. The maximum adsorption capacity of kaolinite towards the dye was found to be 96.5 mg g^?1 (pH 1.0). At the optimal adsorption condition, the dye removal ratio was 95.5%. Dye-saturated kaolinite could desorb at aqueous NaOH, the desorption ratio of dye was 78.8%. The linear Langmuir and Freundlich isotherm models are well fitting to represent the experimental data.     

Modelling the kinetics and equilibrium properties of cadmium biosorption by river green alga and water hyacinth weed

Cadmium biosorption properties of non-living, dried river green alga from a river source, and water hyacinth weed, Eichhornia crassipes from a lake in Zimbabwe have been investigated. The cadmium uptake was found to depend on initial pH, uptake being apparently minimal at low pH values and increasing with an increase in pH. Cadmium biosorption kinetics by both samples is fast, with 80% of total uptake occurring within 60?min. The effect of initial solution pH and initial cadmium concentration on cadmium biosorption from a cadmium solution has been studied. The data for algal biomass fitted the Langmuir monolayer adsorption isotherm, while the biosorption of the metal by water hyacinth weed fitted the Freundlich adsorption isotherm with 1/n values all less than 1. Maximum metal uptake capacities were recorded using 0.35?g of biomass and a 250?mg?L^?1 cadmium solution at pH 6.5 and at 25°C and these were about 85 and 50?mg?L^?1 for water hyacinth weed and green alga, respectively, showing that water hyacinth weed offered a greater potential for cadmium uptake. The absorption was described by pseudo-second order rate model and the rate constant and equilibrium sorption capacity are reported.     

Removal of Eu3+, Ce3+, Sr2+, and Cs+ ions from radioactive waste solutions by modified activated carbon prepared from coconut shells

As a biomass agricultural waste material, coconut shells were used for the preparation of high-quality modified activated carbon. Chemical modification of the surface of the prepared activated carbon is done by oxidation using H₂O₂ and HNO₃, respectively. The surface area and pore volume of the coconut shells activated carbon are increased by the chemical modification, and followingly the removal of the metals is improved. The structural morphology and composition of the modified activated carbon coconut shells (MACCS) were evaluated by Fourier transform infrared (FTIR) spectra, thermogravimetric analysis–differential thermal analysis (TGA-DTA), scanning electron microscope (SEM), X-ray diffraction (XRD), surface area analysis (SAA), X-ray fluorescence (XRF), and carbon, hydrogen, nitrogen, and sulfur (CHNS) elemental analysis. The prepared MACCS has reasonably good chemical stability. The influence of solution pH, contact time, adsorbent dosage, adsorption temperature, initial metal concentrations, and interfering ions on the adsorption performance of the investigated ions onto the prepared sorbent was examined by a batch method. The selectivity sequence for sorption of Eu³⁺, Ce³⁺, Sr²⁺, and Cs⁺ ions on MACCS was found to be Eu^3+?>?Ce^3+?>?Sr^2+?>?Cs⁺. The saturation capacities of MACCS for the studied metal ions were found to be 136.84, 85.55, 69.85, and 60.00?mg?g^?1 for Eu³⁺, Ce³⁺, Sr²⁺, and Cs⁺ ions, respectively. The thermodynamic parameters, ΔH°, ΔS°, and ΔG° were also evaluated.     

Suitability of various chemically prepared activated carbons for the removal of copper(II) ions

Studies on the suitability of various chemically prepared activated carbons (CPACs) like straw carbon (SC), sawdust carbon (SDC), dates nut carbon (DNC) and commercial activated carbon (CAC) for the removal of copper(II) ions by adsorption from simulated wastewater have been carried out under batch mode at 30?±?1°C and the results are compared. The percentage removal of Cu(II) ions increased with a decrease in initial concentration, particle size and added electrolytes (ionic strength) and increased with an increase in contact time, dose of adsorbent and initial pH of the solution. The adsorption data were fitted with the Langmuir isotherm. The applicability of the first order kinetic equation viz. Lagergren equation was tested by correlation analysis. The adsorption process is concluded to be a spontaneous, first order reaction, occurring with increased randomness at the solid–liquid interface. Studies on the desorption of Cu²⁺-loaded activated carbons (ACs) were carried out with nitric acid (0.2–1?N). The possibility of reuse of the regenerated ACs in cycle (in cue-one after another) was tested. SC was found to be a suitable adsorbent alternative to CAC among CPACs for the removal of metal ions, in general, and Cu²⁺ ions, in particular.     

Removal of chromium(VI) by ZnCl2 activated coir pith carbon

The adsorption of chromium(VI) onto ZnCl₂ activated carbon developed from coir pith was investigated to assess the possible use of this adsorbent. The influence of contact time, adsorbent dose, Cr(VI) concentration, pH and temperature were investigated. The two theoretical adsorption isotherms, namely, Langmuir and Freundlich were used to describe the experimental results. The Langmuir adsorption capacity (Q ₀) was found to be 120.5?mg Cr(VI) per g of the adsorbent. The adsorption followed the second-order kinetics and was found to be maximum at pH 2.0. The pH effect and the desorption studies showed that ion exchange mechanism might be involved in the adsorption process. The effects of foreign ions such as chloride, sulphate, phosphate, selenite, molybdate, nitrate and perchlorate on the removal of Cr(VI) have been investigated. The removal of Cr(VI) from synthetic ground water was also tested. The results show that ZnCl₂ activated coir pith carbon is effective for the removal of Cr(VI) from water.     

Removal of Janus Green dye from aqueous solutions using oxidized multi-walled carbon nanotubes

Multi-walled carbon nanotubes (MWCNTs) were oxidized and characterized by Fourier transform infrared spectroscopy. The adsorption characteristics of the oxidized MWCNT adsorbent were examined using Janus Green (JG) as adsorbate. In batch tests, the effects of pH, adsorbent dose, contact time, and temperature were studied. The maximum adsorption capacity was found to be 56 mg g^?1. The experimental data were fitted to the Langmuir, Freundlich, and Tempkin isotherm models, the first one being the most appropriate. Kinetic analysis showed that adsorption was most accurately represented by a pseudo-second-order model.     

Kinetic,equilibrium and thermodynamic studies for the sorption of metribuzin from aqueous solution using banana peels,an agro-based biomass

Banana peels were employed for the removal of metribuzin from aqueous solution. Sorption in the batch mode was optimized regarding pH, contact time, sorbent dose, initial pesticide concentrations, and temperature. The sorption data were fitted to pseudo-first-order, pseudo-second-order, intraparticle diffusion, Elovich, and liquid film diffusion model, the pseudo-second-order exhibiting best fit (R² = 0.9803). Of the four most common sorption isotherm models (Langmuir, Freundlich, Tempkin, and Dubinin–Radushkevich), the data followed the Langmuir isotherm with highest correlation. The maximum adsorption capacity was found to be 167 mg g^?1. Gibbs free energy, enthalpy, and entropy showed that the sorption was exothermic and spontaneous.     

Removal of Mo(VI) from aqueous solutions using sulfuric acid-modified cinder: kinetic and thermodynamic studies

Removal of Mo(VI) from aqueous solutions was investigated using cinder modified by sulfuric acid. Various parameters such as pH, agitation time, Mo(VI) concentration, and temperature have been studied. The maximum adsorption of Mo(VI) occurred at pH between 4.0 and 6.0. Kinetic studies showed that the adsorption generally obeyed a pseudo second-order model. The activation energy was 31.4?kJ?mol^?1, indicating that the adsorption process was governed mainly by interactions of physical nature. Furthermore, application of Langmuir and Freundlich isotherm models to the adsorption equilibrium data showed that the adsorption behavior obeyed the Langmuir model. The adsorption capacity was found to be 10.8?g Mo(VI)?kg^?1 adsorbent. Finally, thermodynamic parameters such as ΔH ⁰, ΔS ⁰, and ΔG ⁰ were also evaluated, which showed that the adsorption of Mo(VI) on the treated cinder was endothermic, entropy increasing, and spontaneous. In conclusion, the sulfuric acid-modified cinder was shown to be an inexpensive, effective, and simple adsorbent for the removal of Mo(VI) from water.