CNTs/TiO2/CS光降解苯的动力学

综合光催化氧化苯的动力学过程、光辐射场模型和质量守恒定律,采用平板型反应器建立了碳纳米管/二氧化钛/壳聚糖（CNTs/TiO2/CS）催化薄膜光催化氧化气相苯的数学模型;该模型考虑了光强、相对湿度、初始浓度与气体流速对气相苯光降解的影响。结果表明,建立的数学模型与实验结果吻合较好。     

碳纳米管/二氧化钛/壳聚糖催化薄膜光催化活性及苯降解机理

通过X-射线衍射仪(XRD)、扫描电镜(SEM)、透射电镜(TEM)和紫外可见光漫反射谱(UV-vis)对碳纳米管/二氧化钛/壳聚糖复合薄膜的晶体结构和形貌进行表征,以室内空气典型污染物气相苯为模型反应物,研究碳纳米管/二氧化钛/壳聚糖催化薄膜的光催化活性及其对苯的光降解机理。结果表明,制备的碳纳米管/二氧化钛/壳聚糖催化薄膜所具有的良好催化活性归功于碳纳米管、二氧化钛和壳聚糖三者的协调效应;气相苯光降解产生的主要中间产物是乙酸乙酯和十一烷,以及少量的丙烯醛、4-羰基-甲基-苯乙酮、十二烷烃、2,4,-二叔丁基苯酚、二十一烷烃。根据红外光谱分析与GC/MS分析结果,进一步提出了气相苯的降解机理过程。     

二氧化钛/碳纳米管/壳聚糖薄膜的制备及对苯的降解性能

研究了光催化降解挥发性有机化合物过程中催化剂二氧化钛/碳纳米管/壳聚糖薄膜的制备以及该催化剂对苯的光催化性能。首先采用溶胶-凝胶法制备纳米复合材料二氧化钛/碳纳米管,然后利用壳聚糖作为交联剂,制得二氧化钛/碳纳米管/壳聚糖复合材料催化薄膜。通过傅立叶红外光谱(FT-IR)、X射线衍射(XRD)透射电镜扫描(TEM)和紫外-可见光漫反射(UV-Vis)等技术分析了复合材料薄膜的组成、结构、形貌和对光的吸收性能,然后使用该催化剂对室内常见的污染物苯进行降解,并在同样的实验条件下,使用催化剂二氧化钛(P25)/壳聚糖对苯进行降解,对两者催化性能进行对比,结果表明,二氧化钛/碳纳米管/壳聚糖对苯有更强的吸附能力和更高的催化活性。     

TiO2纳米粒子气-固复相光催化氧化VOCs作用的研究进展

本文总结了90年代以来TiO2纳米粒子气-固复相光催化氧化气相有机污染物的影响因素、反应机理和动力学,阐述了几种特定有机污染物的光催化氧化过程,并对应用前景作出展望.     

Fe（Ⅲ）/H2O2体系光催化氧化在水处理中应用的研究进展

概述了Fe（Ⅲ）/H2O2体系光催化氧化反应的机理,对Fe（Ⅲ）/H2O2在光催化降解制药废水、染料废水、环境内分泌干扰物等方面的研究进展进行了综述。并对Fe（Ⅲ）/H2O2体系光催化氧化在水处理方面的应用前景进行了展望。     

UV/H_2O_2/TiO_2联合水解酸化+MBR工艺处理亚砜废水

二甲基亚砜(DMSO)废水因其COD高、可生化性差的特性而较难处理。本实验以采用硫酸二甲酯法生产DMSO的某化工厂废水为研究对象,设计并建立了组合式光催化氧化装置联合水解酸化+MBR工艺的中试系统,探讨了组合式光催化氧化装置、氧化剂投加量、pH、反应时间和水力停留时间对系统处理效果的影响。结果表明,组合式光催化氧化装置可有效提高DMSO废水的可生化性。最优工艺参数为:按H2O2与原水COD质量浓度比为2∶1投加H2O2,在pH值为4、反应时间为6 h、水力停留时间为4 h的条件下,该系统对原水COD(5 000 mg/L)去除率大于98%,出水COD达到《污水综合排放标准》(GB 8978-1996)一级要求。     

光反应器中UV/Fenton光降解湖水中微囊藻毒素的研究

在光催化反应器中,采用UV/Fenton光催化氧化技术,对湖水中微囊藻毒素的光催化降解过程中各影响因子分析表明:微囊藻毒素光催化氧化降解率受光照强度、氧化剂种类及浓度、溶液pH和不同光催化体系等多因素的影响.光促催化氧化体系对MC-LR藻毒素降解具有显著的作用,在紫外光与氧化剂的协同作用下,紫外光照强度越高,越易于促进MC-LR藻毒素快速降解,降解率可到达80%以上.     

纳米TiO2光催化氧化去除水中痕量双氯芬酸的研究

以TiCl4为前驱体,采用水解法经不同温度煅烧制备了具有不同理化性能的纳米TiO2光催化剂。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、物理吸附仪、紫外—可见光漫反射吸收光谱(UV-Vis DRS)等手段对纳米TiO2的晶相结构、粒径、孔径分布以及禁带宽度等进行了表征。以蒸馏水配制的双氯芬酸溶液为目标物,进行了纳米TiO2光催化氧化去除双氯芬酸的活性测试,研究了纳米TiO2的理化性能与光催化氧化活性之间的关系。结果表明,经400℃煅烧制得的纳米TiO2样品具有最高的光催化氧化活性,其在紫外光照射60min下对双氯芬酸的去除率为98%左右,比单独紫外光照射高出85百分点。纳米TiO2光催化氧化去除双氯芬酸的反应近似一级反应动力学模型,其中经400℃煅烧制得的纳米TiO2光催化氧化去除双氯芬酸的表观反应速率常数为0.054 54min-1,是普通商用TiO2的2倍左右,与德国Degussa P-25TiO2的光催化氧化活性最相近。     

TiO2纳米粒子气—固复相光催化氧化VOCs作用的研究进展

本文总结了９０年代以来ＴｉＯ２纳米粒子气－固复相光催化氧化气相有机污染物的影响因素,瓜是和动力学,阐述了几种特定有机污染物的光催化氧化过程,并对应用前景作出展望。     

光催化耦合常温催化氧化HCHO的Bi3+-TiO2/MnCeOx催化剂性能

常用净化室内挥发性有机物(VOCs)的方法主要有吸附、低温等离子体、光催化氧化、常温催化氧化等,而鲜有基于光催化耦合常温催化催化剂的报道。以具备常温催化氧化性能的MnCeO_x为载体,以具有可见光催化性能的Bi_<sup>3+-TiO₂为活性组分,考察负载量、煅烧温度、制备方法以及结构形态等对Bi_<sup>3+-TiO₂/MnCeO_x催化氧化甲醛(HCHO)性能的影响,并利用XRD、BET、SEM、TEM、UV-vis DRS和IR等技术对催化剂进行微观表征与分析。结果表明,催化剂表观结构形态、晶型、粒径、孔道、掺杂、可见光吸收及抗水性为Bi_<sup>3+-TiO₂/MnCeO_x氧化性能提升提供了必要条件,两者间的多重协同耦合作用是核心,其中采用浸渍法所制的负载量10.0%Bi_<sup>3+-TiO₂/M...     

Photocatalytic Degradation of the Herbicide Erioglaucine in the Presence of Nanosized Titanium Dioxide: Comparison and Modeling of Reaction Kinetics

The present work mainly deals with photocatalytic degradation of a herbicide, erioglaucine, in water in the presence of TiO₂ nanoparticles (Degussa P-25) under ultraviolet (UV) light illumination (30 W). The degradation rate of erioglaucine was not so high when the photolysis was carried out in the absence of TiO₂ and it was negligible in the absence of UV light. We have studied the influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO₂, irradiation time and initial concentration of erioglaucine on the photodegradation efficiency of erioglaucine. A kinetic model is applied for the photocatalytic oxidation by the UV/TiO₂ system. Experimental results indicated that the photocatalytic degradation process could be explained in terms of the Langmuir–Hinshelwood kinetic model. The values of the adsorption equilibrium constant, K, and the second order kinetic rate constant, k, were 0.116 ppm^{? 1} and 0.984 ppm min^{? 1}, respectively. In this work, we also compared the reactivity between the commercial TiO₂ Degussa P-25 and a rutile TiO₂. The photocatalytic activities of both photocatalysts were tested using the herbicide solution. We have noticed that photodegradation efficiency was different between both of them. The higher photoactivity of Degussa P-25 compared to that of rutile TiO₂ for the photodegradation of erioglaucine may be due to higher hydroxyl content, higher surface area, nano-size and crystallinity of the Degussa P-25. Our results also showed that the UV/TiO₂ process with Degussa P-25 as photocatalyst was appropriate as the effective treatment method for removal of erioglaucine from a real wastewater. The electrical energy consumption per order of magnitude for photocatalytic degradation of erioglaucine was lower with Degussa P-25 than in the presence of rutile TiO₂.     

Cu/La共掺杂TiO2光催化氧化水中的氨氮

采用水解-沉淀法制备了Cu/La共掺杂纳米TiO2催化剂,利用XRD、XPS和BET技术对其进行表征,并考察了在紫外灯下,共掺杂TiO2对氨氮的光催化氧化工艺条件。物相结构和比表面积测试结果表明,共掺杂催化剂具有较好的锐钛矿晶型,孔径分布为4～8 nm,Cu/La共掺杂TiO2La以La3+,Cu是以Cu2+、Cu+的形式掺杂进入TiO2的晶格。光催化实验表明:所得改性光催化剂对氨氮的去除及焦化废水的处理均具有较高的催化活性。     

Influence of palladium content dispersed in the TiO2 photocatalyst for degradation of volatile organic compounds in gas emission

Heterogeneous photocatalysis is highlighted to treat volatile organic compound (VOC) emission. Then, this work analysed the influence of palladium (Pd) content loaded in TiO₂ on n-octane and iso-octane photodegradation. For this, TiO₂ was loaded with Pd in different contents: 0.4%, 0.7%, and 1.0%. The samples were characterized, and the photodegradation experiments were conducted by Pd/TiO₂/UV process. The characterization analyses showed that the metal presence did not change the catalyst structure or its surface area; however, it reduced the bandgap energy. The photocatalytic results proved that palladium improved n-octane degradation from 62% (pure TiO₂) to 92.6% (0.4%Pd/TiO₂) and, iso-octane degradation enhanced from 59% (pure TiO₂) to 90.6% (0.7%Pd/TiO₂); all results were obtained in the space time of 39 s. Therefore, 0.4%Pd/TiO₂ and 0.7%Pd/TiO₂ showed better oxidation results to degradation n-octane and iso-octane, respectively. The kinetic model of pseudo-first order showed a good fit for the data of both VOCs. Heterogeneous photocatalysis with Pd/TiO₂ showed to be an adequate technique to reduce VOCs emission.

     

纳米Bi2O3/TiO2复合光催化剂的制备及性能研究

以光催化效果为评价标准,采用超声波作用下水解法制备Bi₂O₃/TiO₂复合光催化剂,考察了水解条件和Bi₂O₃掺入量等制备条件对复合光催化剂性能的影响。结果表明,与传统制备方法相比,该方法操作简单、快速;当水和乙醇的比例为4∶1时所得样品的光催化活性最好;Bi₂O₃的掺入拓宽了TiO₂对光的吸收范围,提高了TiO₂的光催化活性,掺入量(Bi₂O₃)为0.25%复合光催化剂催化活性最高;复合光催化剂对多种水溶性染料均具有较好的处理效果。     

Adsorption and photocatalytic decomposition of roxarsone by TiO2 and its mechanism

Roxarsone (3-nitro-4-hydroxyphenylarsonic acid) has been widely used as organic arsenic additive in animal industry. In this study, the adsorption of roxarsone on TiO₂ under dark conditions, the photocatalytic decomposition of roxarsone under UV/TiO₂, and the possible photocatalytic pathway were investigated. At the initial concentration of 5–35 mg/L, the adsorption of roxarsone fitted well with the pseudo-second-order kinetics. The isotherms analysis showed that the Langmuir model was better than the Freundlich and Dubinin–Radushkevich models for describing the adsorption process. After 7 h of photocatalytic decomposition, a complete disappearance of roxarsone was achieved. The pH value has a significant effect on both adsorption and photocatalytic decomposition of roxarsone. The results of high-performance liquid chromatography-hydride generation-atomic fluorescence spectrometry (HPLC-HG-AFS) and gas chromatography-mass spectrometry (GC/MS) analyses proved the cleavage of the As-C bond during the photocatalytic decomposition process by TiO₂ and the intermediates of the decomposition. Based on the results, a possible photocatalytic decomposition pathway was proposed.     

Enhanced photocatalytic activity using GO/TiO<Subscript>2</Subscript> catalyst for the removal of DCA solutions

This work aimed to optimize high-performance photocatalysts based on graphene oxide/titanium dioxide (GO/TiO₂) nanocomposites for the effective degradation of aqueous pollutants. The catalytic activity was tested against the degradation of dichloroacetic acid (DCA), a by-product of disinfection processes that is present in many industrial wastewaters and effluents. GO/TiO₂ photocatalysts were prepared using three different methods, hydrothermal, solvothermal, and mechanical, and varying the GO/TiO₂ ratio in the range of 1 to 10%. Several techniques were applied to characterize the catalysts, and better coupling of GO and TiO₂ was observed in the thermally synthesized composites. Although the results obtained for DCA degradation showed a coupled influence of the composite preparation method and its composition, promising results were obtained with the photocatalysts compared to the limited activity of conventional TiO₂. In the best case, corresponding to the composite synthesized via hydrothermal method with 5% of GO/TiO₂ weight ratio, an enhancement of 2.5 times of the photocatalytic degradation yield of DCA was obtained compared to bare TiO₂, thus opening more efficient ways to promote the application of photocatalytic remediation technologies.     

Relationship between Pd oxidation states on TiO2 and the photocatalytic oxidation behaviors of nitric oxide

This study has been undertaken to investigate the relationship between Pd oxidation states on TiO₂ photocatalysts and their photocatalytic oxidation behaviors of NO. Three types of Pd-modified TiO₂ with different Pd oxidation states were prepared by wet impregnation method, neutralization method and photodeposition method, respectively. And these Pd-modified photocatalysts were characterized by X-ray diffraction analysis, X-ray photoelectron spectrum analysis (XPS), UV–Vis diffuse reflectance spectra and temperature programmed desorption (TPD). It was found from XPS results that the dominant oxidation states of Pd on these Pd-modified TiO₂ catalysts were Pd²⁺, PdO, and Pd⁰, respectively. NO-TPD results showed that the NO adsorption capacity was improved greatly by the modification of Pd²⁺ ions. The activity tests showed that Pd-modified TiO₂ by a wet impregnation method increased photocatalytic activity compared to pure TiO₂ (Degussa P25). It was concluded that Pd²⁺ ions on as-prepared TiO₂ catalysts provided key contributions to the improvement of photocatalytic activity. However, Pd⁰ and PdO deposits on TiO₂ almost had no positive effect on NO oxidation. The mechanism of photocatalytic oxidation of NO in gas phase over Pd-modified TiO₂ was also proposed.     

Photocatalytic degradation of acetaminophen in modified TiO2 under visible irradiation

This study investigated the photocatalytic degradation of acetaminophen (ACT) in synthetic titanium dioxide (TiO₂) solution under a visible light (λ >440 nm). The TiO₂ photocatalyst used in this study was synthesized via sol–gel method and doped with potassium aluminum sulfate (KAl(SO₄)₂) and sodium aluminate (NaAlO₂). The influence of some parameters on the degradation of acetaminophen was examined, such as initial pH, photocatalyst dosage, and initial ACT concentration. The optimal operational conditions were also determined. Results showed that synthetic TiO₂ catalysts presented mainly as anatase phase and no rutile phase was observed. The results of photocatalytic degradation showed that LED alone degraded negligible amount of ACT but with the presence of TiO₂/KAl(SO₄)₂, 95 % removal of 0.10-mM acetaminophen in 540-min irradiation time was achieved. The synthetic TiO₂/KAl(SO₄)₂ presented better photocatalytic degradation of acetaminophen than commercially available Degussa P-25. The weak crystallinity of synthesized TiO₂/NaAlO₂ photocatalyst showed low photocatalytic degradation than TiO₂/KAl(SO₄)₂. The optimal operational conditions were obtained in pH 6.9 with a dose of 1.0 g/L TiO₂/KAl(SO₄)₂ at 30 °C. Kinetic study illustrated that photocatalytic degradation of acetaminophen fits well in the pseudo-first order model. Competitive reactions from intermediates affected the degradation rate of ACT, and were more obvious as the initial ACT concentration increased.