Oxidation and biotoxicity assessment of microcystin-LR using different AOPs based on UV,O3 and H2O2

MC-LR removal performances under different AOPs were compared systematically. Higher removal efficiency and synergistic effects were obtained by combined process. The acute biotoxicity raised in different degrees after oxidation. Microcystin-LR attracts attention due to its high toxicity, high concentration and high frequency. The removal characteristics of UV/H₂O₂ and O₃/H₂O₂ advanced oxidation processes and their individual process for MC-LR were investigated and compared in this study. Both the removal efficiencies and rates of MC-LR as well as the biotoxicity of degradation products was analyzed. Results showed that the UV/H₂O₂ process and O₃/H₂O₂ were effective methods to remove MC-LR from water, and they two performed better than UV-, O₃-, H₂O₂-alone processes under the same conditions. The effects of UV intensity, H₂O₂ concentration and O₃ concentration on the removal performance were explored. The synergistic effects between UV and H₂O₂, O₃ and H₂O₂ were observed. UV dosage of 1800 mJ·cm⁻² was required to remove 90% of 100 mg·L⁻¹ MC-LR, which amount significantly decreased to 500 mJ·cm⁻² when 1.7 mg·L⁻¹ H₂O₂ was added. 0.25 mg·L⁻¹ O₃, or 0.125 mg·L⁻¹ O₃ with 1.7 mg·L⁻¹ H₂O₂ was needed to reach 90% removal efficiency. Furthermore, the biotoxicity results about these UV/H₂O₂, O₃/H₂O₂ and O₃-alone processes all present rising trends with oxidation degree of MC-LR. Biotoxicity of solution, equivalent to 0.01 mg·L⁻¹ Zn²⁺, raised to 0.05 mg·L⁻¹ Zn²⁺ after UV/H₂O₂ or O₃/H₂O₂ reaction. This phenomenon may be attributed to the aldehydes and ketones with small molecular weight generated during reaction. Advice about the selection of MC-LR removal methods in real cases was provided.     

KMnO4/H2SO4引发制备淀粉改性絮凝剂的研究

以高锰酸钾为引发剂,制备淀粉-丙烯酰胺接枝共聚物.研究酸浓度、引发剂浓度、单体浓度、温度和加料方式对接枝反应的影响.结果表明,少量KMnO4(0.45mmol·l-1)和H2SO4(0.8mmol·l-1)可有效引发淀粉-丙烯酰胺接枝共聚反应,接枝效率达到90%以上,分子量大大提高,对高岭土的絮凝效果较好.     

大气CO2、CH4、CO高精度观测混合标气配制方法

高精度、高准确度的大气CO2、CH4、CO浓度观测需使用以干洁大气为底气的标气.标气中水汽含量及CO2的δ13C对基于光学原理的观测系统有不可忽视的影响.本研究利用自组装的混合标气配制系统,以环境大气为底气,并通过添加高浓度气体或利用吸附剂吸附,调节目标物种浓度.CO2和CO吸附效率分别达99.7%和99.8%,标气水汽含量小于3.7×10-6(物质的量分数,下同),可配制不同浓度范围的CO2、CH4、CO混合标气.在青海瓦里关全球大气本底站配制环境大气浓度范围的标气,CO2、CH4、CO实际配制浓度同目标浓度的偏差小于10×10-6、30×10-9、30×10-9,CO2中δ13C同实际大气接近.本方法配制的标气已应用于我国本底站大气CO2、CH4、CO高精度观测,符合世界气象组织/全球大气观测(WMO/GAW)质量要求.     

Decomposition of aqueous chlorinated contaminants by UV irradiation with H2O2

In the present study, the decomposition rates of carbon tetrachloride (CCl₄) and 2,4-dichlorophenol (2,4-DCP) in water by the ultraviolet (UV) light irradiation alone and H₂O₂/UV were experimentally investigated. The detailed experimental studies have been conducted for examining treatment capacities of the two different ultraviolet light sources (low and medium pressure Hg arc) in H₂O₂/UV processes. The low or medium UV lamp alone resulted in a 60%–90% decomposition of 2,4-DCP while a slight addition of H₂O₂ resulted in a drastic enhancement of the 2,4-DCP decomposition rate. The decomposition rate of 2,4-DCP with the medium pressure UV lamp alone was about 3–6 times greater than the low pressure UV lamp alone. In the direct photolysis of aqueous CCl₄, the medium pressure UV lamp had advantage over the low pressure UV lamp because the molar extinction coefficient of CCl₄ at shorter wavelength (210–220 nm) is about 20 to 50 times higher than that at 254 nm. However, adding H₂O₂ to the medium pressure UV lamp system rendered a negative oxidation rate because H₂O₂ acted as a UV absorber being competitive with CCl₄ due to negligible reaction between CCl₄ and OH radicals. The results from the present study indicated significant influence of the photochemical properties of the target contaminants on the photochemical treatment characteristics for designing cost-effective UV-based degradation of toxic contaminants.     

Catalytic oxidation of CO over Pt/Fe3O4 catalysts: Tuning O2 activation and CO adsorption

• Strong metal-support interaction exists on Pt/Fe₃O₄ catalysts. • Pt metal particles facilitate the formation of oxygen vacancies on Fe₃O₄. • Fe₃O₄ supports enhance the strength of CO adsorption on Pt metal particles. The self-inhibition behavior due to CO poisoning on Pt metal particles strongly impairs the performance of CO oxidation. It is an effective method to use reducible metal oxides for supporting Pt metal particles to avoid self-inhibition and to improve catalytic performance. In this work, we used in situ reductions of chloroplatinic acid on commercial Fe₃O₄ powder to prepare heterogeneous-structured Pt/Fe₃O₄ catalysts in the solution of ethylene glycol. The heterogeneous Pt/Fe₃O₄ catalysts achieved a better catalytic performance of CO oxidation compared with the Fe₃O₄ powder. The temperatures of 50% and 90% CO conversion were achieved above 260°C and 290°C at Pt/Fe₃O₄, respectively. However, they are accomplished on Fe₃O₄ at temperatures higher than 310°C. XRD, XPS, and H₂-TPR results confirmed that the metallic Pt atoms have a strong synergistic interaction with the Fe₃O₄ supports. TGA results and transient DRIFTS results proved that the Pt metal particles facilitate the release of lattice oxygen and the formation of oxygen vacancies on Fe₃O₄. The combined results of O₂-TPD and DRIFTS indicated that the activation step of oxygen molecules at surface oxygen vacancies could potentially be the rate-determining step of the catalytic CO oxidation at Pt/Fe₃O₄ catalysts. The reaction pathway involves a Pt-assisted Mars-van Krevelen (MvK) mechanism.     

Enhancing O2 electroreduction to H2O on Ag/MnO2-CHNTs by boosting a four-electron catalytic pathway

A fundamental question in the oxygen reduction reaction(ORR)is how to rationally control the electrocatalytic selectivity for opening a four-electron reaction pathway. However, it still lacks direct experimental evidence to understand the reaction mechanism. This work unravels that Ag nanoparticles and carbonizing halloysite nanotubes(CHNTs) can trigger the construction of oxygen defects in the MnO₂, which contribute to the generation of active sites. The Ag/MnO₂-CHNTs deli...     

Optimization of the O3/H2O2 process with response surface methodology for pretreatment of mother liquor of gas field wastewater

• Real ML-GFW with high salinity and high organics was degraded by O₃/H₂O₂ process. • Successful optimization of operation conditions was attained using RSM based on CCD. • Single-factor experiments in advance ensured optimal experimental conditions. • The satisfactory removal efficiency of TOC was achieved in spite of high salinity. • The initial pH plays the most significant role in the degradation of ML-GFW. The present study reports the use of the O₃/H₂O₂ process in the pretreatment of the mother liquor of gas field wastewater (ML-GFW), obtained from the multi-effect distillation treatment of the gas field wastewater. The range of optimal operation conditions was obtained by single-factor experiments. Response surface methodology (RSM) based on the central composite design (CCD) was used for the optimization procedure. A regression model with Total organic carbon (TOC) removal efficiency as the response value was established (R² = 0.9865). The three key factors were arranged according to their significance as: pH>H₂O₂ dosage>ozone flow rate. The model predicted that the best operation conditions could be obtained at a pH of 10.9, an ozone flow rate of 0.8 L/min, and H₂O₂ dosage of 6.2 mL. The dosing ratio of ozone was calculated to be 9.84 mg O₃/mg TOC. The maximum removal efficiency predicted was 75.9%, while the measured value was 72.3%. The relative deviation was found to be in an acceptable range. The ozone utilization and free radical quenching experiments showed that the addition of H₂O₂ promoted the decomposition of ozone to produce hydroxyl radicals (·OH). This also improved the ozone utilization efficiency. Gas chromatography-mass spectrometry (GC-MS) analysis showed that most of the organic matters in ML-GFW were degraded, while some residuals needed further treatment. This study provided the data and the necessary technical supports for further research on the treatment of ML-GFW.     

过氧化氢和一氧化氮在小球藻抗阿特拉津胁迫中的作用

过氧化氢(H_2O_2)和一氧化氮(NO)作为信号分子,可调节植物生长、发育以及应对外源性胁迫。利用过氧化氢酶(CAT)以及NO清除剂(PTIO),研究了除草剂阿特拉津(atrazine,100μg·L~(-1))影响小球藻生长的机理,并分析内源性H_2O_2和NO在小球藻抗除草剂胁迫中的作用。研究结果表明,阿特拉津在诱发小球藻细胞死亡的过程中,不同程度促发了H_2O_2和NO生成;外源CAT可通过清除H_2O_2和诱导NO来缓解阿特拉津对小球藻的生长抑制;PTIO与阿特拉津的联合实验进一步证实,小球藻体内的NO诱导与H_2O_2的爆发无关,它们之间的合成没有相关性。因此,除草剂阿特拉津主要通过诱导小球藻体内的H_2O_2爆发来破坏藻细胞,抑制其生长,与NO的信号传递无关。     

Heterostructuring noble-metal-free 1T' phase MoS2 with g-C3N4 hollow nanocages to improve the photocatalytic H2 evolution activity

In this work,we report the preparation of 1T’-MoS₂/g-C₃N₄ nanocage(NC) heterostructure by loading 2D semi-metal noble-metal-free 1T’-MoS₂ on the g-C₃N₄ nanocages(NCs).DFT calculation and experimental data have shown that the 1T’-MoS₂/g-C₃N₄ NC heterostructure has a stronger light absorption capacity and larger specific surface area than pure g-C₃N₄ NCs and g-C₃N     

A novel strategy for loading metal cocatalysts onto hollow nano-TiO2 inner surface with highly enhanced H2 production activity

The loading strategy of cocatalysts affects its activity exerting and atom utilization.Here,a novel strategy for loading precious metal(Pt)cocatalysts by means of ultrathin N-doped carbon layer is reported.The strategy is based on a pyrolysis process of predesigned N-containing polymers and Pt complexes on hard-template surface,during which Pt can be reduced by carbon from pyrolysis at high temperatures.Finally,the hollow TiO₂ composite with stable and dispersed Pt on its inner surfac...     

磷酸活化活性炭对Cu2+的吸附特征研究

寻求廉价而高效的吸附材料为目的,研究向日葵秸杆基活性炭对铜离子的吸附性能。以向日葵秸秆为原料,经H3PO4活化制备活性炭,通过静态实验研究了其对水溶液中Cu2+的吸附特性,考察了溶液pH值、吸附温度和离子强度对吸附的影响,探讨了吸附热力学、动力学和吸附机理。结果表明:溶液pH值为5～6时活性炭对Cu2+的去除效果最好;向50 mL 170 mg·L-1的溶液中加入0.5 g活性炭,温度为45℃、吸附时间为1 h时,对Cu2+的去除率可达98.3%;Langmuir方程能更好地描述Cu2+在活性炭上的等温吸附特征,静态吸附容量可达41.03 mg·g-1;吸附过程符合拟二级动力学过程,且为吸热的化学吸附过程,膜扩散为速率控制步骤,离子交换可能在吸附过程中起了重要作用。     

Sunlight-controlled CO2 separation resulting from a biomass-based CO2 absorber

Renewable solid sorbents for CO₂ capture and storage have shown great potentials for the sake of gaseous separation, tail gas treatment,environmental regulation and climate governance. However, current existed preparation and reusability of solid sorbents are generally subject to high energy consumption and complicated procedure. Herein, a light-controlled CO₂ separation system with high working temperature resulting from natural sawdust combined with polyethyleneimine is f...     

Hydroxyl radical intensified Cu2O NPs/H2O2 process in ceramic membrane reactor for degradation on DMAc wastewater from polymeric membrane manufacturer

• Cu₂O NPs/H₂O₂ Fenton process was intensified by membrane dispersion. • DMAc removal was enhanced to 98% for initial DMAc of 14000 mg/L. • Analyzed time-resolved degradation pathway of DMAc under ·OH attack. High-concentration industrial wastewater containing N,N-dimethylacetamide (DMAc) from polymeric membrane manufacturer was degraded in Cu₂O NPs/H₂O₂ Fenton process. In the membrane-assisted Fenton process DMAc removal rate was up to 98% with 120 min which was increased by 23% over the batch reactor. It was found that ·OH quench time was extended by 20 min and the maximum ·OH productivity was notably 88.7% higher at 40 min. The degradation reaction rate constant was enhanced by 2.2 times with membrane dispersion (k = 0.0349 min⁻¹). DMAc initial concentration (C₀) and H₂O₂ flux (J_p) had major influence on mass transfer and kinetics, meanwhile, membrane pore size (r_p) and length (L_m) also affected the reaction rate. The intensified radical yield, fast mass transfer and nanoparticles high activity all contributed to improve pollutant degradation efficiency. Time-resolved DMAc degradation pathway was analyzed as hydroxylation, demethylation and oxidation leading to the final products of CO₂, H₂O and NO₃⁻ (rather than NH₃ from biodegradation). Continuous process was operated in the dual-membrane configuration with in situ reaction and separation. After five cycling tests, DMAc removal was all above 95% for the initial [DMAc]₀ = 14,000 mg/L in wastewater and stability of the catalyst and the membrane maintained well.     

A Cu-modified active carbon fiber significantly promoted H2S and PH3 simultaneous removal at a low reaction temperature

• Cu_0.15-ACF performs the best for H₂S and PH₃ simultaneous removal. • 550°C and 90°C are separately calcination and reaction temperatures. • The reason why Cu_0.15/ACF shows better performance was found. • The accumulation of H₂PO₄⁻ and SO₄²⁻(H₂O)₆ is the deactivation cause of Cu_0.15/ACF. Poisonous gases, such as H₂S and PH₃, produced by industrial production harm humans and damage the environment. In this study, H₂S and PH₃ were simultaneously removed at low temperature by modified activated carbon fiber (ACF) catalysts. We have considered the active metal type, content, precursor, calcination, and reaction temperature. Experimental results exhibited that ACF could best perform by loading 15% Cu from nitrate. The optimized calcination temperature and reaction temperature separately were 550°C and 90°C. Under these conditions, the most removal capacity could reach 69.7 mg/g and 132.1 mg/g, respectively. Characterization results showed that moderate calcination temperature (550°C) is suitable for the formation of the copper element on the surface of ACF, lower or higher temperature will generate more cuprous oxide. Although both can exhibit catalytic activity, the role of the copper element is significantly greater. Due to the exceptional dispersibility of copper (oxide), the ACF can still maintain the advantages of larger specific surface area and pore volume after loading copper, which is the main reason for better performance of related catalysts. Finally, increasing the copper loading amount can significantly increase the crystallinity and particle size of copper (oxide) on the ACF, thereby improving its catalytic performance. In situ IR found that the reason for the deactivation of the catalyst should be the accumulation of generated H₂PO₄⁻ and SO₄²⁻(H₂O)₆ which could poison the catalyst.     

Influence of H2S and NH3 on biogas dry reforming using Ni catalyst: a study on single and synergetic effect

● NH₃ in biogas had a slight inhibitory effect on dry reforming. ● Coexistence of H₂S and NH₃ led to faster decline of biogas conversion. ● Regeneration was effective for catalysts deactivated under synergetic effect. Biogas is a renewable biomass energy source mainly composed of CH₄ and CO₂. Dry reforming is a promising technology for the high-value utilization of biogas. Some impurity gases in biogas can not be completely removed after pretreatment, which may affect the performance of dry reforming. In this study, the influence of typical impurities H₂S and NH₃ on dry reforming was studied using Ni/MgO catalyst. The results showed that low concentration of H₂S in biogas could cause serious deactivation of catalyst. Characterization results including EDS, XPS and TOF-SIMS confirmed the adsorption of sulfur on the catalyst surface, which was the cause of catalyst poisoning. We used air calcination method to regenerate the sulfur-poisoned catalysts and found that the regeneration temperature higher than 500 °C could help catalyst recover the original activity. NH₃ in the concentration range of 50–10000 ppm showed a slight inhibitory effect on biogas dry reforming. The decline rate of biogas conversion efficiency increased with the increase of NH₃ concentration. This was related to the reduction of oxygen activity on catalyst surface caused by NH₃. The synergetic effect of H₂S and NH₃ in biogas was investigated. The results showed that biogas conversion decreased faster under the coexistence of H₂S and NH₃ than under the effect of H₂S alone, so as the surface oxygen activity of catalyst. Air calcination regeneration could also recover the activity of the deactivated catalyst under the synergetic effect of H₂S and NH₃.     

H_2O_2致大鼠RTE细胞系氧化应激作用及GSH保护作用的体外研究

许多具有氧化作用的空气污染物,均能使细胞产生氧化损伤,使胸腺基质淋巴生成素(thymic stromal lymphopoietin,TSLP)含量上升。而TSLP是一种启动过敏性炎症的重要因子,会导致哮喘等疾病发生率的上升。在本研究中用过氧化氢(H_2O_2)模拟具有氧化作用的空气污染物进行染毒,研究细胞氧化应激水平的变化,并讨论还原型谷胱甘肽(GSH)对细胞受氧化损伤的保护作用。将大鼠支气管上皮细胞(RTE)分组培养,每组设置6个平行实验,分别用低、中、高剂量H_2O_2染毒3 h;高剂量设置1个重复,作为保护组,在染毒前用GSH保护2 h。结果显示,高剂量组H_2O_2(3.2 mmol·L~(~(-1)))染毒的细胞,其细胞活力下降(P0.01),丙二醛(MDA)水平上升(P0.01),TSLP水平上升(P0.05),与之相比,用GSH保护后的同剂量染毒组,上述指标得到全面缓解(P0.01)。这表明高浓度的H_2O_2会损伤细胞活力,并使MDA及TSLP水平上升,而GSH对TSLP及MDA的升高有极显著的抑制作用,即对细胞有一定的保护作用。     

Catalytic ozonation of organic compounds in water over the catalyst of RuO2/ZrO2-CeO2

This research investigates the performances of RuO₂/ZrO₂-CeO₂ in catalytic ozonation for water treatment. The results show that RuO₂/ZrO₂-CeO₂ was active for the catalytic ozonation of oxalic acid and possessed higher stability than RuO₂/Al₂O₃ and Ru/AC. In the catalytic ozonation of dimethyl phthalate (DMP), RuO₂/ZrO₂-CeO₂ did not enhance the DMP degradation rate but significantly improved the total organic carbon (TOC) removal rate. The TOC removal in catalytic ozonation was 56% more than that in noncatalytic ozonation. However this does not mean the catalyst was very active because the contribution of catalysis to the overall TOC removal was only 30%. The adsorption of the intermediates on RuO₂/ZrO₂-CeO₂ played an important role on the overall TOC removal while the adsorption of DMP on it was negligible. This adsorption difference was due to their different ozonation rates. In the catalytic ozonation of disinfection byproduct precursors with RuO₂/ZrO₂-CeO₂, the reductions of the haloacetic acid and trihalomethane formation potentials (HAAFPs and THMFPs) for the natural water samples were 38%–57% and 50%–64%, respectively. The catalyst significantly promoted the reduction of HAAFPs but insignificantly improved the reduction of THMFPs as ozone reacts fast with the THMs precursors. These results illustrate the good promise of RuO₂/ZrO₂-CeO₂ in catalytic ozonation for water treatment.     

Simultaneous removal of NOx and chlorobenzene on V2O5/TiO2 granular catalyst: Kinetic study and performance prediction

• A V₂O₅/TiO₂ granular catalyst for simultaneous removal of NO and chlorobenzene. • Catalyst synthesized by vanadyl acetylacetonate showed good activity and stability. • The kinetic model was established and the synergetic activity was predicted. • Both chlorobenzene oxidation and SCR of NO follow pseudo-first-order kinetics. • The work is of much value to design of multi-pollutants emission control system. The synergetic abatement of multi-pollutants is one of the development trends of flue gas pollution control technology, which is still in the initial stage and facing many challenges. We developed a V₂O₅/TiO₂ granular catalyst and established the kinetic model for the simultaneous removal of NO and chlorobenzene (i.e., an important precursor of dioxins). The granular catalyst synthesized using vanadyl acetylacetonate precursor showed good synergistic catalytic performance and stability. Although the SCR reaction of NO and the oxidation reaction of chlorobenzene mutually inhibited, the reaction order of each reaction was not considerably affected, and the pseudo-first-order reaction kinetics was still followed. The performance prediction of this work is of much value to the understanding and reasonable design of a catalytic system for multi-pollutants (i.e., NO and dioxins) emission control.     

Influence of MnOx deposition on TiO2 nanotube arrays for electrooxidation

TiO₂ has demonstrated outstanding performance in electrochemical advanced oxidation processes(EAOPs) due to its structural stability and high oxygen overpotential.However,there is still much room for improving its electrochemical activity.Herein,narrow bandgap manganese oxide(MnOx) was composited with TiO₂ nanotube arrays(TiO₂ NTAs) that in-situ oxidized on porous Ti sponge,forming the MnO_x-TiO₂ NTAs anode.XANES and XPS analysis further prov...     

Ultra-small UiO-66-NH2 nanoparticles immobilized on g-C3N4 nanosheets for enhanced catalytic activity

UiO-66-NH₂,an important metal-organic framework,is usually synthesized by solvothermal method and the particle size is generally larger than 200 nm,which limits its catalytic applications in chemical reactions.It is very meaningful to produce UiO-66-NH₂ nanoparticles with ultrasmall size,but remains challenging.Herein,we synthesized UiO-66-NH₂ nanoparticles in size of 8-15 nm that are immobilized on g-C₃N₄ nanosheets.Compared with the UiO-66...