Rapid detection of toxic metals in non-crushed oyster shells by portable X-ray fluorescence spectrometry

The aim of this study was the multi-elemental detection of toxic metals such as lead (Pb) in non-crushed oyster shells by using a portable X-ray fluorescence (XRF) spectrometer. A rapid, simultaneous multi-element analytical methodology for non-crushed oyster shells has been developed using a portable XRF which provides a quick, quantitative, non-destructive, and cost-effective mean for assessment of oyster shell contamination from Pb. Pb contamination in oyster shells was further confirmed by scanning electron microscopy with energy dispersive spectroscopy (SEM-EDS). The results indicated that Pb is distributed in-homogeneously in contaminated shells. Oyster shells have a lamellar structure that could contribute to the high accumulation of Pb on oyster shells.     

Particle emissions of a railway line determined by detailed single particle analysis

The goal of this study was to identify and quantify particles emitted from railway traffic. For that purpose PM10 samples were collected near a busy railway line using a wind direction and speed controlled sampling equipment consisting of five devices. Measurements taken perpendicular to the railway lines at 10, 36 and 120 m distance enable an identification and separation of particles caused by the railway traffic from background particles. Morphology and chemistry of more than 11,000 particles were analysed by computer controlled scanning electron microscopy (CCSEM). Based on chemical composition five particle classes are defined and assigned to their sources. The mass of the individual particles is determined by multiplying their volumes, calculated based on their morphology with a density assigned specifically to each particle class. The density of the particle classes is derived from their chemical composition. To estimate the PM10 contributions of the railway lines, the mass of PM10 at 120 m (background, not influenced by the railway lines) is subtracted from the mass of PM10 at 10 m. The emissions of the railway lines are dominated by ‘iron’ particles, which contribute 2.9 μg m⁻³ or 67% to the railway related PM10. In addition, ‘aluminium’ and ‘calcium’ particles contribute also to the railway related PM10 (1.0 μg m⁻³ or 23% for the ‘aluminium’ and 0.4 μg m⁻³ or 10% for the ‘calcium’ particles). These particles are assigned to abrasion of the gravel bed and re-suspension of mineral dust.Long-term gravimetric results of the contribution of iron to the mass of railway related PM10 from a study performed earlier at the same site are in good agreement with the data presented in this study.     

Source Apportionment of Particulate Matter (PM10) and Indoor Dust in a University Building

A study on source apportionment of indoor dust and particulate matter (PM₁₀) composition was conducted in a university building by using chemometrics. The objective of this study was to investigate the potential sources of selected heavy metals and ionic species in PM₁₀ and indoor dust. PM₁₀ samples were collected using a low-volume sampler (LVS) and indoor dust was collected using a soft brush. Inductively coupled plasma spectrometry (ICP-MS) was used to determine the concentration of heavy metals, while the concentration of cations and anions was determined by atomic absorption spectrometer (AAS) and ion chromatography (IC), respectively. The concentration of PM₁₀ recorded in the building throughout the sampling period ranged from 20 ± 10 μgm^?3 to 80 ± 33 μgm^?3. The composition of heavy metals in PM₁₀ and indoor dust were dominated by zinc (Zn), followed by lead (Pb), copper (Cu), and cadmium (Cd). Principle component analysis (PCA) and multiple linear regression (MLR) showed that the main sources of pollutants in PM₁₀ came from indoor renovations (73.83%), vehicle emissions (16.38%), earth crust sources (9.68%), and other outdoor sources (0.11%). For indoor dust, the pollutant source was mainly earth crust. This study suggests that chemometrics can be used for forensic investigation to determine the possible sources of indoor contaminants within a public building.     

Testing Re-entrained Aerosol Kinetic Emissions from Roads : a new approach to infer silt loading on roadways

PM₁₀ and PM_2.5 emissions from roadways are currently estimated using the silt loading on the road surface as a surrogate for the emissions potential of road dust. While the United States Environmental Protection Agency prescribes this method in AP-42, there is considerable cost associated with silt loading measurements; it is feasible to sample only a small portion of a roadway network. A new approach for measuring the concentration of suspendable PM₁₀ above road surfaces has been developed to obtain a more spatially representative estimate of a road's potential to emit dust. The Testing Re-entrained Aerosols Kinetic Emissions from Roads (TRAKER) system uses real-time aerosol sensors mounted on a vehicle to measure the concentration of dust suspended from the road while the vehicle is in motion. When coupled with a Global Positioning System (GPS) instrument, TRAKER can be used to efficiently survey the changes in suspendable particles due to varying road conditions over a large spatial domain.In a recent study on paved roads in Las Vegas, the TRAKER system was compared with collocated silt loading measurements. The TRAKER system was also used to survey the relative amounts of suspendable road dust on approximately 300 miles of paved roads. The system provides a unique perspective on road dust sources and their spatial distribution.Results of this study indicated that the difference of the PM₁₀ concentrations measured behind the tire and on the hood is exponentially related to vehicle speed. This was an interesting finding because current AP-42 road dust emissions estimation methods do not include vehicle speed as a factor in the emissions calculations. The experiment also demonstrated that the distribution of suspendable material on roadways is highly variable and that a large number of samples are needed to represent road dust emissions potential on an urban scale for a variety of road and activity conditions.     

一种新型国产高效除尘滤筒在船厂分段涂装车间的应用

国产除尘滤材是将聚酯纤维热轧成型 ,再涂敷高分子发泡制成。滤材硬挺、耐压、抗撕裂 ,内部结构稳定 ,粉尘过滤精度高 ,实现表面过滤 ,易清灰再生 ,使用寿命长 ,耐水、酸、碱 ,可广泛用于各工业领域的气体净化和粉尘处理。大连新船重工集团把国产除尘滤材制成的滤筒配置到厂内原有的除尘系统中 ,通过 1年多的使用 ,获得非常满意的除尘效果。从而证明国产滤料性能已达到国际先进水平。     

Application of neutral electrolyzed water spray for reducing dust levels in a layer breeding house

Reducing airborne dust is an essential process for improving hen housing environment. Dust reduction effects of neutral electrolyzed water (pH 8.2) spray were investigated in a commercial tunnel-ventilated layer breeding house during production in northern China. A multipoint sampler was used to measure airborne dust concentration to study the dust reduction effects and distribution in the house. Compared with the control treatment (without spray), airborne dust level was reduced 34% in the 3 hr after spraying 216 mL m^?2 neutral electrolyzed water in the breeding house. The dust concentration was significantly higher during the periods of feed distribution (1.13 ± 0.13 mg m^?3) and artificial insemination (0.72 ± 0.13 mg m^?3) compared with after spray (0.47 ± 0.09 mg m^?3) and during lights-off period (0.29 ± 0.08 mg m^?3) in the three consecutive testing days (P < 0.05). The experimental cage area was divided into four zones along the length of the house, with zone 1 nearest to the evaporative cooling pad and zone 4 nearest to the fans. The air temperature, relative humidity, airflow rate, and dust concentration were measured at the sampling points of the four zones in 3 consecutive days and mortality of the birds for the duration of a month were investigated. The results showed that the air temperature, airflow rate, dust concentration, and number of dead birds increase from zone 1 to zone 4 in the tunnel-ventilated layer breeding house.

Implications: It is difficult to effectively reduce hen house airborne dust levels and limited information is available on airborne dust distribution in tunnel-ventilated hen houses. This work investigates (i) the application of neutral electrolyzed water spray for reducing dust in a layer breeding houses; (ii) dust concentration variations in 24-hr house operation; as well as (iii) the effects of location on dust concentrations. It was demonstrated that neutral electrolyzed water spray can be efficiently used for dust reduction in poultry houses. Further, a better understanding of the dust concentration variations in 24-hr house operation and in different spatial zones can contribute to bird housing environment management and poultry house design so as to improve bird health.     

Dietary intake of hexabromocyclododecane diastereoisomers (α-, β-, and γ-HBCD) in the Belgian adult population

A study was performed to assess exposure of the Belgian population to HBCD diastereoisomers. Measurements of HBCD were performed by UPLC-MS/MS, on 45 composite samples from 5 major food groups: dairy (products), meat (products), eggs, fish (products) and a group of “other” products. The medium bound estimated average daily intake (EDI) of ΣHBCD in the Belgian population was 0.99 ng kg⁻¹ bw d⁻¹. The diastereoisomer contribution to the mean EDI showed a predominance of γ-HBCD at 67%, followed by α-HBCD at 25% and 8% for β-HBCD. These results are consistent with the pattern found in the two food groups contributing the most to the EDI: meat (products) and the group of “other” products. Anyway, it has to be noted that diastereomeric distribution of HBCD can change due to bioisomerisation in biological material. Levels of HBCD diastereoisomers found in Belgian food samples of animal origin were low in comparison with those found in other EU countries and the resulting EDI was substantially below the proposed thresholds.     

以废纸为原料制备煤尘抑制剂的合成及应用

采用碱化、醚化法制备了以废纸为原料的煤尘抑制剂,借助FTIR、SEM、TG-DTA及XRF等手段对合成物进行了表征,并将其用于抑制煤尘进行性能测试。结果表明,羧甲基纤维素的取代度为0.69;选用羧甲基纤维素含量为0.5g/mL的煤尘抑制剂进行应用实验,效果最佳。9 h内,喷洒含有羧甲基纤维素的煤尘抑制剂的煤样表面已经结壳,抗七级风,抑尘率在130 h都可保持在99%以上。在较高温燃烧条件下,煤尘抑制剂以H2O和CO2的形式失去,不会产生有害物质。     

钢棒去皮机除尘器设计

钢棒去皮机是通过砂轮磨削除去钢棒表面铁锈的一种设备，在去皮过程产生的大量金属粉尘，导致环境污染，为此设计喷淋塔式除尘器作为钢棒去皮机的除尘装置。通过选择和计算的运行参数，设计了喷淋塔的结构和尺寸。对设计的除尘器效率验算结果表明：该除尘器可以满足去皮机环保要求，除尘效率达99．7％。     

钢棒去皮机除尘器设计

钢棒去皮机是通过砂轮磨削除去钢棒表面铁锈的一种设备,在去皮过程产生的大量金属粉尘,导致环境污染,为此设计喷淋塔式除尘器作为钢棒去皮机的除尘装置。通过选择和计算的运行参数,设计了喷淋塔的结构和尺寸。对设计的除尘器效率验算结果表明:该除尘器可以满足去皮机环保要求,除尘效率达99.7%。     

Role of Chinese wind-blown dust in enhancing environmental pollution in Metropolitan Seoul

A suite of rock magnetic experiments and intensive microscopic observations were carried out on Asian dust deposits in Seoul, Korea, collected on 19 and 23 March 2002, 9 April 2002 and 12 April 2003. Desert-sand and loess from the dust source regions in China were also analyzed as a comparison. Asian dust showed a higher magnetic concentration than the source region samples, indicating a significant influx of magnetic particles into Asian dust had occurred during its transportation. Electron microscopy identified carbon-bearing iron-oxides as the added material. These iron-oxides were likely to have been produced by anthropogenic pollution (fossil fuel combustion) while the wind-blown dusts passing across the industrial areas of eastern China and western Korea. Such wind-paths were confirmed by a simulation of the air-mass trajectories. The magnetic technique appears to be useful for determining the anthropogenic pollution of Asian dust.     

Polybrominated diphenyl ethers in house dust in Singapore

The use of polybrominated diphenyl ethers (PBDEs) as flame retardants in Singapore is not strictly regulated; therefore these compounds can be readily found in furniture, electronic devices, and building materials. This study was the first of its kind to be conducted in Singapore to measure concentrations of PBDEs in house dust. Samples were collected from 31 homes in various locations across the island-state of Singapore, and a total eight PBDEs congeners were measured. PBDEs were detected in all 31 dust samples and the number of BDE congener detected per home ranged between 3 and 8. The most abundant BDE congeners found were BDE 47, 99 and 209, with a median value of 20 ng g(-1) dust, 24 ng g(-1) dust and 1000 ng g(-1) dust, respectively. BDE 209 contributed 88% to the median of all the congeners, and BDE 47 and 99 contributed 1.8% and 3.5%, respectively. Different congener profiles were observed between this and studies conducted elsewhere, which is consistent with the use of different commercial PBDE around the world. No significant correlations between PBDE dust levels and residential characteristics (number of TVs and computers, floor area or flooring material) were observed. The daily intake of PBDEs via the inhalation pathway was estimated. House dust may be regarded as the most important exposure route of PBDEs for children.     

Chamber studies on mass-transfer of di(2-ethylhexyl)phthalate (DEHP) and di-n-butylphthalate (DnBP) from emission sources into house dust

For a number of phthalates and especially for di(2-ethylhexyl)phthalate (DEHP), surprisingly high house dust concentrations are reported in the literature. Therefore, the uptake of the most prominent compounds DEHP and di-n-butylphthalate (DnBP) from plasticized indoor materials into house dust samples of different organic content has been experimentally determined. The experiments have been performed within 45 days which is sufficient for the more volatile phthalate (DnBP) to reach equilibrium conditions. DnBP reaches considerably higher concentrations in the chamber air compared to real room measurements and, thus, also elevated dust concentrations. In contrast, the mass transfer of DEHP in the dust via the gas phase was significantly lower. However, small chamber experiments showed elevated mass transfer of DEHP in case of direct contact between emission source and sink. This aspect is experimentally determined using an plasticized PVC polymer with and without direct contact to house dust. A transfer into the dust could be observed in dependence of the initial concentration in the material. However, the results do not allow the differentiation between the two uptake mechanisms via capillary forces and contact to the material’s boundary layer. The results illustrate that the reasons for elevated DEHP concentrations in dust indoors can be traced back to direct contact of source and sink, abrasion from the source, and transport via airborne particles.     

The Prediction of Overall Collection Efficiency of Air Pollution Control Devices from Fractional Efficiency Curves

The application of air pollution control devices requires the prediction of overall collection efficiency from the particle size distribution of the dust and the fractional efficiency of the air pollution control device. The cumulative particle size distribution of dust resulting from industrial processes can usually be represented by a straight line on logarithmic probability paper or a log normal function. The fractional efficiency curves of many air pollution control devices such as cyclones or wet scrubbers can also be adequately represented by a log normal function. Only two parameters are required to define a log normal function, a median diameter and a geometric standard deviation. Both of these can easily be obtained from a plot on logarithmic probability paper. The overall collection efficiency has been found to be Very simply related to the four parameters required to define the log normal functions representing the particle size distribution and the collector fractional efficiency. These four parameters are: the mass median diameter and the geometric standard deviation of the dust size distribution, the cut diameter (50% efficiency diameter), and geometric standard deviation of collector fractional efficiency curve. Using this relationship the prediction of overall collection efficiency is greatly simplified with no loss of accuracy.     

Identification of Pollution Source of Cadmium in Soil. Application of Material Flow Analysis and A Case Study in Taiwan (11 pp)

Background Since the 1970s, at least 200 hectares (ha) of farmland has been polluted by the heavy metal cadmium (Cd).Consequently, the Cd pollution has led to contaminate the rice production and caused acute social panic. According to the recent investigation results performed by the Taiwan Environmental Protection Administration (TEPA), it is indicated that most of the Cd pollution incidents in Taiwan resulted from the wastewater discharge of stearate Cd factories. To prevent the Cd pollution incidents from spreading, the TEPA has either forced these factories to close down or assisted them in improving their production processes since the 1980s. Unfortunately, accidental incidents of Cd pollution still emerge in an endless stream, despite the strict governmental controls placed on these questionable factories. Whether this pollution has resulted from undetected or hidden pollution sources stemming from two decades ago or comes from some new source, will be an outstanding issue. Therefore, this study attempts to identify the pollution sources of Cd in soil in Taiwan as well as to find the solution to the above-mentioned, outstanding issue by way of a methodology termed Material Flow Analysis (MFA). Method logy. The MFA has proved to be a useful tool on providing quantitative information of the flow of substances through an economic to an environmental system. Based upon the supply-and-demand theory of MFA, researchers have successfully conducted an overview of the use of materials in many industries, the construction industry being one of these. Therefore, this study tries to establish a set of analytical processes by way of MFA for identifying the pollution source of Cd in soil in Taiwan. In addition, the spirit of Life Cycle Analysis (LCA) technique was also employed to identify the materials, and products should be ignored as a crucial pollution source in this study. Results and Discussion According to the MFA methodology applied in this study and on the basis of related studies performed by Taiwanese governmental authorities, we arrive at the following analysis results: (1) the total amount of Cd from the economic perspective of material and product flow was approximately 441.2 tons; (2) the wastewater directly discharged into irrigation water can be concluded to be the major pollution route of Cd in farmland soil in Taiwan; (3) material plastic stabilizer (cadmium oxide, CdO), Zn-Pd compounds and Cu compounds should be the crucial pollution sources to contaminate environment through the route of wastewater in Cd flow analysis; (4) the crucial pollution sources to contaminate environment through the route of wastewater in Cd flow analysis were five factories, Coin, Jili, Taiwan Dye, Guangzheng and Mingguan, and they were all categorized as stearate Cd industries; (5) the typical source of the Cd pollution in soil in Changhua County through the pollution route of wastewater should be the metal surfacing process industries. Conclusions This study proved that MFA can be a good tool for identifying Cd flow as well as for recognizing the crux of the problem concerning incidents of Cd pollution. This study led to the conclusion that the causal relationship between farmland pollution caused by Cd and stearate Cd factories in Taiwan seemed quite close by way of MFA methodology. In addition, this study also found that the wastewater discharged from a single metal surfacing process factory will not cause remarkable farmland pollution. However, the wastewater simultaneously discharged from a group of pollution factories can result in a significant pollution incident. Recommendations and Outlook This case study is only a small contribution to the understanding of the toxic material flow related to Cd in the environment. This study recommends that Taiwanese governmental authorities should not deal with problems on an ad hoc basis, but should instead deal with Cd pollution problems overall employing control measures. Finally, the more accurate information or data we can collect, the more reliable results we can identify. Therefore, the quality and quantity of related data used in this MFA model should be closely scrutinized in order to ensure the most correct and comprehensive investigation on the toxic material flow.     

Chemical characterization and source identification/apportionment of fine and coarse air particles in Thessaloniki,Greece

The distribution of air particulate mass and selected particle components (trace elements and polycyclic aromatic hydrocarbons (PAHs)) in the fine and the coarse size fractions was investigated at a traffic-impacted urban site in Thessaloniki, Greece. 76±6% on average of the total ambient aerosol mass was distributed in the fine size fraction. Fine-sized trace elemental fractions ranged between 51% for Fe and 95% for Zn, while those of PAHs were between 95% and 99%. A significant seasonal effect was observed for the size distribution of aerosol mass, with a shift to larger fine fractions in winter. Similar seasonal trend was exhibited by PAHs, whereas larger fine fractions in summer were shown by trace elements. The compositional signatures of fine and coarse particle fractions were compared to that of local paved-road dust. A strong correlation was found between coarse particles and road dust suggesting strong contribution of resuspended road dust to the coarse particles. A multivariate receptor model (multiple regression on absolute principal component scores) was applied on separate fine and coarse aerosol data for source identification and apportionment. Results demonstrated that the largest contribution to fine-sized aerosol is traffic (38%) followed by road dust (28%), while road dust clearly dominated the coarse size fraction (57%).     

Spatial and Seasonal Variations of Disinfection Byproducts (DBPs) in Drinking Water Distribution Systems of Istanbul City,Turkey

This study presents the seasonal and spatial variations of trihalomethanes (THMs) and haloacetic acids (HAAs) in 30 sampling points within three water distribution systems of Istanbul City, Turkey. The effects of surface water quality, seasonal variation, and species differences were examined. The occurrence of chlorinated THMs and HAAs levels was considerably lower in the system in which raw water is subjected to pre-ozonation versus pre-chlorination. Seasonal analysis of the data indicated that the median concentration of four THMs (THM₄) was higher than nine HAAs (HAA₉) concentrations in all three distribution systems sampling points. For all distribution systems monitored, the highest median THM₄ and HAA₉ concentrations were observed in the spring and summer season, while the lowest concentrations of these disinfection byproduct (DBP) compounds were obtained in the fall and winter period. Due to the higher level of bromide in supplying waters of these two systems, moderate levels of brominated DBP species have been observed in the Kagithane and Buyukcekmece distribution systems districts. In fact, Spearman partial correlations (Spearman rank correlation coefficients [rs]) tend to be higher among analogues in terms of number and types of substituent, especially TCAA with TCM (rs 0.91), and DBAA with DBCM (rs 0.90). In contrast, the hydraulic (residence time and flow rate) and chemical mechanisms (hydrolysis, volatilization, and adsorption) affect the fate and transport of DBPs in distribution systems. Seasonal and spatial variations of DBPs presented in this study have important implications on regulatory issues and from an epidemiological point of view.     

Detection of Asian dust (Hwangsa) over the Yellow Sea by decomposition of unpolarized infrared reflectivity

The periodical occurrence of Asian dust (Hwangsa) in East Asia during every spring and winter is of great consequence to regional human health and visibility. One weakness of the previous methods based on the brightness temperature (BT) differences or optical depths is that they can not accurately detect the dust events over the Yellow Sea. This study proposes a unique technique of decomposing unpolarized reflectivities to distinguish between dust and clouds over the sea surface. Many current infrared (IR) satellite instruments such as MTSAT-1R measure the unpolarized radiance. In this process, an approximate relationship between vertically and horizontally polarized reflectivities is validated for the IR wavelengths of 3–12 μm. The radiances observed from an IR geostationary satellite and the simulated sea surface temperature (SST) are used for a case study of Asian dust events. The results show qualitatively the reasonable spatial agreements with MODIS true color images for these Asian dust events. The proposed method in this study can be utilized for the operational purpose to detect the signal of Asian dust over sea surface.     

粉尘对电除尘器气流分布影响仿真研究

为了更加精确地研究电除尘器入口气流分布特征, 论文采用欧拉-拉格朗日多相流模型,对电除尘器内部气流分布进行了数值仿真。由于在进入除尘器的气流中引入了粉尘粒子,不仅可获得粉尘及粉尘颗粒粒径大小对气流分布均匀性的影响,而且这种模拟更加接近除尘器的气流实际情况。提出的模拟方法为电除尘器的气流分析提供了一条新的途径。     

Emission of respirable dust from stone quarrying,potential health effects,and its management

Mining of minerals exerts adverse pressure on different compartments of environment directly or indirectly. Air is the worst affected environmental matrix, and it can carry the harmful effect of pollutants generated from mining activity even to distant places. The present study was undertaken to estimate the emission of particulate matter (PM_2.5 and PM₁₀) from different activities undertaken in stone quarrying in Mahendragarh, Haryana. The results obtained from the present study indicated that drilling, blasting, crushing, and transport of mined material are chiefly responsible for the generation of dust. Whereas drilling, blasting, and loading were responsible for emission of higher fraction of PM₁₀, crushing and re-suspension of roadside dust from movement of vehicles resulted in generation of relatively higher fraction of finer dust (PM_2.5). Modelling the transport of dust over the Hybrid Single-Particle Lagrangian Integrated Trajectory model revealed that the emitted particle may move up to the distance of about 40 km within 4 h of emission under average meteorological conditions. Fourier transform infrared (FTIR) spectroscopy analysis of dust confirmed the presence of calcite and gypsum, thus confirming the source as mining. The study concluded that generation of PM_2.5-sized particles may impose serious respiratory health effects over the workers engaged in mining, crushing, and transportation of sandstone. Apart from it, population residing downwind of the mining area is particularly vulnerable to the pulmonary effects due to inhalation of dust.