Environmental Monitoring Of Remedial Dredging At The New Bedford Harbor, Ma, Superfund Site

New Bedford Harbor (NBH), MA, is a Superfund site because of high polychlorinated biphenyl (PCB) concentrations in the sediment. From April 1994 to September 1995, a remedial dredging operation (termed the “Hot Spot”) removed the most contaminated sediments (PCB concentrations greater than 4000μg/g) from the upper harbor. During remediation, a monitoring program assessed the potential environmental impacts to NBH and adjacent Buzzards Bay. The monitoring program was developed with input from federal, state, and local authorities. Site-specific decision criteria were established to assess net PCB transport, water column toxicity, and PCB bioaccumulation in blue and ribbed mussels (Mytilus edulis and Geukensia demissa, respectively). The remediation was completed without exceeding PCB net transport or acute toxicity effects specified in the decision criteria. In addition, PCB bioaccumulation in mussels during this time period was not significantly greater than pre- or post-operational measurements. The results indicated that approximately 14000 cubic yards of highly PCB contaminated sediment were permanently removed with minimal environmental effects. The lessons learned during this operation, as well as previous pilot studies at the site, will be used to make full-scale remedial efforts in NBH more efficient and environmentally protective.     

Quantitative analyses of selected polychlorinated biphenyl (PCB) congeners in water,soil, and sediment during winter and spring seasons from Msunduzi River,South Africa

The lack of information and the need for knowledge on the organic pollutants within the area of KwaZulu-Natal together with the global problem of water supply have prompted our investigation into the analyses of eight polychlorinated biphenyl (PCB) congeners in the Msunduzi River of KwaZulu-Natal, South Africa. Soil, sediment, and water samples were collected at ten different sites along the river during winter and spring seasons. Soil and sediment samples were extracted using ultra sonication with dichloromethane while water samples were liquid-liquid extracted using dichloromethane. All sample extracts were cleaned-up using a multi-layer silica gel column and analyzed with gas chromatography-mass spectrometry. Quality assurance measures were also determined. The percentage recoveries for water were 53–128 for all the PCBs analyzed, while sediment recoveries ranged between 69 and 105%. The highest total concentrations of the PCBs in sediment were 214.21–610.45 ng/g dw at the Du Toit sampling site and 30.86–444.43 ng/g dw basis at the wastewater treatment inlet for winter and spring, respectively. Soil PCB concentrations were 76.53–397.75 ng/g dw at the Msunduzi Town sampling site and 20.84–443.49 ng/g (dry weight) at the Du Toit sampling site for winter and spring, respectively. In addition, high PCB concentrations were found in effluent of the wastewater treatment inlet compared to other sampling sites, which ranged between 0.68–22.37 and 2.53–35.69 ng/mL for winter and spring seasons, respectively. In all the sampling sites selected for this study, Du Toit afforded the highest PCB concentration levels and the lowest was after chlorination at the Darvill wastewater treatment plant. The results presented are new and it is the first study of organic pollutants such as PCBs that has been carried out on this river.     

Occurrence of PAHs and PCBs in the Alna River, Oslo (Norway)

Thirty two polychlorinated biphenyl congeners (PCBs), hexachlorobenzene (HCB) and pentachlorobenzene (PeCB) were analysed in passive sampler extracts from surface water-exposed semipermeable membrane devices (SPMDs) and in bed sediment samples from a small urban watercourse, the River Alna (Oslo, Norway). Performance reference compound-corrected data from the passive samplers deployed at three sites along the river were used to track PCB contamination in the overlying water. SPMDs were able to detect an increase in dissolved PCB concentrations at the site furthest downstream that was corroborated by bed sediment concentrations. In comparison, no major increase in concentration of HCB, PeCB or PAHs could be observed. Comparison of passive sampling-based overlying water concentrations with total concentrations measured in bed sediments supports the possibility of further PCB sources upstream of the study area. Diagnostic PAH ratios (from SPMDs) and PCB congener pattern (from sediments) were used in an attempt to identify possible contaminant sources to the Alna River. Selected PAH diagnostic ratios support a multiple emission source scenario and demonstrate the complexity of identifying specific sources of these compounds to surface waters. PCB congener patterns in sediments from all three sites tend to indicate a source of highly chlorinated PCBs (of the Archlor 1260 type) and either a source of lower chlorinated PCBs or the less-likely occurrence of dechlorination in sediment. Information collected during the present screening study also confirms the Alna River as a continuous source of PCBs to the Oslofjord.     

Chemical and bioassay monitoring of PCB-contaminated soil remediation using solvent extraction technology

Illegal dumping of polychlorinated biphenyl (PCB) capacitors was discovered in Kobe, Japan, in 2001, leaving about 68 m(3) (92 tons) of soil contaminated with approximately 6.6 kg of PCBs. Solvent extraction technology carried out in 2002-2003 using isopropyl alcohol remedied the affected soil at the site. Forty-seven batch treatments were conducted during full-scale treatment. On average, 8.4 extraction cycles per batch were needed to achieve the clean-up goal for PCBs (i.e., the Japanese environmental quality standard for soil). Analytical results showed that the average PCB concentration (88 microg g(-1)-dry soil) in untreated soil samples of all the batches was decreased to 1.2 microg g(-1)-dry soil in treated soil samples, yielding a removal efficiency of 98.6%. Dioxin responsive-chemical activated luciferase gene expression assay (DR-CALUX) and enzyme-linked immunosorbent assay (ELISA) adopting a monoclonal antibody against 2,3',4,4',5-pentachlorobiphenyl (PCB #118) were used to rapidly screen soil samples before and after solvent extraction. The DR-CALUX and ELISA results were in good agreement with World Health Organization toxicity equivalent values and analytically determined PCB concentrations, respectively. Regular monitoring during the treatment period confirmed that the applied technology met Japanese environmental and control regulations concerning treatment and disposal of contaminated soils and treatment residues. After full-scale treatment, the amount of PCBs recovered from the solvent purification system approximated the estimated amount of PCBs spilled.     

Sediment influence on congener-specific PCB bioaccumulation by Mytilus edulis: a case study from an intertidal hot spot, Clyde Estuary, UK

An intertidal site in the Clyde Estuary, UK, was selected to evaluate the role of sediment geochemistry on the bioaccumulation of polychlorinated biphenyls (PCBs) by mussels (Mytilus edulis). The area had previously been identified as showing anomalously high levels of PCB contamination (over 1,500 microg kg(-1) total PCB in sediment, 22 congeners). Samples of surface sediment and M. edulis were collected from two closely located sites, one within the anomalous area and another representing typical PCB contamination in the estuary. Sediment samples were separated into grain size fractions and analysed for a range of biomarker compounds, PCBs and sediment mineralogy. The anomalous site showed an atypical association of PCBs with sediment properties, despite both locations showing influence of both petrogenic and pyrogenic organic contamination. Interrogation of data using correlation and principal component analysis showed that sediment mineralogy as well as organic matter composition influenced PCB congener distribution. One sediment source was found to control the PCB concentration in mussels at both locations and clay mineralogy appears to control PCB uptake by biota with preference for higher molecular weight congeners. Overall bioavailability is determined by sediment TOC.     

土壤和沉积物中多氯联苯单体测定的净化方法研究

对浓硫酸净化、铜粉脱硫、氟罗里硅土柱、硅胶柱、石墨碳柱等净化方法在土壤和沉积物多氮联苯单体测定中的应用进行了研究.浓硫酸对多氯联苯单体的净化回收率达92.4％～109％;氟罗里硅土柱用正己烷/丙酮混合溶液淋洗,净化洗脱液体积为8 mL～10 mL时,回收率达85.7％ ～ 108％;硅胶柱用正己烷淋洗,净化洗脱液体积为...     

Dehalogenation of polychlorinated biphenyls and polybrominated diphenyl ethers using a hybrid bioinorganic catalyst

The environmentally prevalent polybrominated diphenyl ether (PBDE) #47 and polychlorinated biphenyls (PCBs) #28 and #118 were challenged for 24 hours with a novel biomass-supported Pd catalyst (Bio-Pd(0)). Analysis of the products via GC-MS revealed the Bio-Pd(0) to cause the challenged compounds to undergo stepwise dehalogenation with preferential loss of the least sterically hindered halogen atom. A mass balance for PCB #28 showed that it is degraded to three dichlorobiphenyls (33.9%), two monochlorobiphenyls (12%), and biphenyl (30.7%). The remaining mass was starting material. In contrast, while PCB #118 underwent degradation to yield five tetra- and five trichlorinated biphenyls, no less chlorinated products or biphenyl were detected, and the total mass of degraded products was 0.3%. Although the Bio-Pd(0) material was developed for treatment of PCBs, a mass balance for PBDE #47 showed that the biocatalyst could prove a potentially useful method for treatment of PBDEs. Specifically, 10% of PBDE #47 was converted to identifiable lower brominated congeners, predominantly the tribrominated PBDE #17 and the dibrominated PBDE #4, 75% remained intact, while 15% of the starting mass was unaccounted for.     

Catalytic hydrogenation of polyaromatic hydrocarbon (PAH) compounds in supercritical carbon dioxide over supported palladium

A series of supported palladium catalysts were evaluated for their ability to mediate the complete hydrogenation of polycyclic aromatic hydrocarbon (PAH) compounds. Benzo[a]pyrene (B[a]P) or phenanthrene (Phe) in hexane was merged with a hydrogen-carbon dioxide [5% (w/w) H(2)/CO(2)] stream and transferred to a flow through mini-reactor (capacity ca. 1 g) that was maintained at 90 degrees C under a back-pressure of 20.68 MPa. Effluent from the reactor trapped in hexane was monitored/quantified by gas chromatography-mass spectrometry. Catalyst formulations supported on iron powder, high density polyethylene (HDPE) or gamma-alumina were prepared and compared in terms of hydrogenation activity as measured by the quantity of substrate per unit time that could be perhydrogenated to toxicologically innocuous products. Both of the Pd preparations supported on gamma-alumina were more efficient than a commercial Pd(0) (5% w/w) on gamma-Al(2)O(3) formulation or preparations supported on HDPE or the iron powder. Bimetallic mixtures with Pd increased the hydrogenation activity when co-deposited with Cu or Ni but not with Ag or Co. However, increases in hydrogenation activity by increasing the loading of Pd (or bimetallic mixture) on this surface were limited. Despite using supercritical carbon dioxide (scCO(2)) to swell the surfaces of the polymer, the deposition of nanoparticles within the polyethylene formulation was appreciably less active than either the oxidic or the Fe(0) formulations.     

The effect of size and sex on PCB and PAH concentrations in crab Portunus pelagicus

Polychlorinated biphenyl and polycyclic aromatic hydrocarbon concentrations in the hepatopancreas of blue swimming crab (Portunus pelagicus) from the north Persian Gulf were measured. In addition, the relationships between crab size (carapace width) and polychlorinated biphenyl (PCB) and polycyclic aromatic hydrocarbon (PAH) levels in hepatopancreas were investigated by linear regression analysis. Among the PCBs, congeners 110 and 153 were the most frequent and abundant. The results showed that, except in a few cases, significant relationships between PCB and PAH levels and crab size were positive. Comparison between male and female indicated that the average PCB16, 44, 153, and acenaphthylene, acenaphthene, and anthracene concentrations in hepatopancreas of male crab were found to be significantly higher than those found in the female crab.     

吹扫捕集-气相色谱质谱法分析土壤和沉积物中挥发性有机物

采用吹扫捕集-气相色谱质谱法对土壤和沉积物中挥发性有机物进行分析,优化了实验条件,所有物质的相对标准偏差小于5.0％,土壤样回收率在78.2％ ～99.8％之间,沉积物样的回收率在55.2％～95.2％之间.     

Enantiomeric signatures of chiral polychlorinated biphenyl atropisomers in livers of harbour porpoises (Phocoena phocoena) from the southern North Sea

The enantiomeric composition of polychlorinated biphenyl (PCB) atropisomers, including PCB 95, PCB 149 and PCB 132, was measured in 11 livers of harbour porpoises (Phocoena phocoena) from the southern North Sea. Non-racemic enantiomeric ratios (ERs) were found in some samples. The value of ERs in three of the four juvenile porpoises was equal or almost equal to one, while the ERs in all adults differed from racemic and ranged from 1.31 to 2.54 for PCB 95; from 1.19 to 1.81 for PCB 149 and from 0.45 to 0.94 for PCB 132. There were no relationships between the total concentration of PCBs and ERs. To understand the phenomena, the relationships between the ER value of individual chiral congener with age, concentration of total PCBs and PCB congener pattern were discussed. A model of intake and elimination kinetics was set up and it was tested using the ratio between concentration of PCB 153 and PCB 101 in the liver samples. There was a clear trend between the enantiomeric ratios and the ratio between PCB 153 and PCB 101. Considering that PCB 153 is one of the most persistent PCB congeners in marine mammals and PCB 101 is a relatively easy metabolised congener, this trend means that the enantiomeric ratio most likely reflects the proportion of the metabolised congener. The exposure period in contaminated conditions has a strong impact on ERs, and it is suggested that ERs in wildlife, combined with information on their anthropometric data, health status, diet and habitat conditions, might be good indicators of pollution in coastal ecosystems.     

Polychlorinated biphenyls (PCBs) analysis using a miniaturized high-resolution time-of-flight mass spectrometer "MULTUM-S II"

In this study, we conducted polychlorinated biphenyls (PCBs) analysis using fast gas chromatography (GC)/high-resolution mass spectrometry (HRMS). Mass spectrometry (MS) was performed with a miniature multi-turn time-of-flight (TOF) analyzer called "MULTUM-S II". MULTUM-S II is truly a portable high resolution mass spectrometer. The mass spectrometer's high resolution capability is due to its theoretical infinite flight path utilizing perfect space and time focusing within a closed flight orbit. Mass resolution above 10?000 was easily achievable employing this portable system. This mass resolution is comparable to magnetic sector mass spectrometers, which have traditionally performed PCB analyses in the past. At a resolution of 10?000, a limit-of-detection of 1 ppb was determined using a heptachlorinated biphenyl standard sample. Using this fast GC/HRMS, 66 PCB congeners were analyzed within 5 min. In addition experiments aimed at confirming interference of PCB signal peaks and matrix peaks in diluted dielectric coolant fluids were performed. We found that the PCB signal peaks were detected without matrix interference via high mass resolution.     

Remediation of a nonachloro biphenyl congener with zero-valent iron in subcritical water

Dechlorination of a nonachloro biphenyl congener with zero-valent iron in water under high temperature and pressure was investigated over time. Temperature has the main influence on the speed of dechlorination. Determination of polychlorinated biphenyls (PCBs) according to the grade of chlorination was performed by gas chromatography with mass selective detection in single ion monitoring mode. Dechlorination results in a variety of lower chlorinated biphenyls. The level of chlorination decreases with time. The amount of PCB molecules decreases to one-third within 90 min at 250 degrees C and 100 atm. However, no increase of biphenyl could be detected over time. A first-order kinetic model fitted the data obtained.     

Trends in background levels of persistent organic pollutants at Kosetice observatory, Czech Republic.2) Part II. Aquatic and terrestrial environments 1996-2005

A multimedia sampling of ambient air, wet deposition, surface water, sediment, soil and biota has been performed at Kosetice background observatory in the southern Czech Republic since 1988. An integrated monitoring approach was applied to assess the current state, anthropogenic impacts, and possible future changes of terrestrial and freshwater environments. Average PCB concentrations in the individual matrices calculated from ten years of sampling on multiple sites varied between 2 ng g(-1) in sediment and 7 ng g(-1) in soil or moss. DDT concentrations were lower in moss and needles (2 ng g(-1) and 4 ng g(-1), respectively) than in sediment (11 ng g(-1)) and soil (20 ng g(-1)), while the HCH level was higher in moss and needles (5 ng g(-1) and 6 ng g(-1), respectively) than in soil or sediment (1 ng g(-1) and 2 ng g(-1), respectively). The highest average level of PAHs was found in soil (600 ng g(-1)), while it was lower in needles (230 ng g(-1)), moss (210 ng g(-1)) or sediment (210 ng g(-1)). Time related trends of concentration levels of persistent organic pollutants in all matrices were investigated. Moss and needle trend patterns resembled those of the ambient air, showing a slight concentration decrease of all compounds, except for hexachlorobenzene. The soil, water and sediment concentrations showed a similar decrease of PAHs, PCBs, and HCHs, but there was no clear trend for DDTs and HCB.     

Determinations of PCB within a project to develop cleanup methods for PCB-containing elastic sealant used in outdoor joints between concrete blocks in buildings

Determinations of PCB were carried out as part of a project aimed at developing cleanup methods for PCB-containing elastic sealant used in outdoor joints between concrete blocks. The goals of the project were to develop methods, which minimise the spread of PCB to the outdoor environment and to indoor air, and which keep the PCB levels as low as reasonably possible in the workplace environment whilst removing the elastic sealant. The following PCB determinations were carried out: (1) concentration in the elastic sealant; (2) concentration in the concrete close to the sealant; (3) concentration in soil; (4) concentration in the indoor air; and (5) concentration in the air in the workplace environment. The cleanup process consisted of a number of different steps: (1) cutting the elastic sealant with an oscillating knife; (2) grinding the concrete with a mechanical machine; (3) sawing the concrete with a mechanical saw and (4) cutting the concrete with a mechanical chisel. In all these different steps a high capacity vacuum cleaner connected to the machines was used. The elastic sealant contained 4.7 to 8.1% total PCB of a technical product with a composition most similar to Clophene A40. The concrete close to the sealant (first 2 mm) contained 0.12 and 1.7% total PCB at two different places. The pattern of the PCB in the concrete resembled that of the sealant. PCB concentrations in the soil from the ground close to the building were 0.1 and 0.3 ppm at two different places before the remedial action. The source of the PCB in the soil is most likely the sealant as the PCB pattern is similar for the two materials. The PCB levels in the workplace air at the beginning of the project, when the techniques were not fully developed, were generally above the occupational exposure limit of 10 micrograms m-3 (up to 120 micrograms m-3). Later when the techniques were optimised to better take care of dust and gases produced during the cutting and grinding etc., the levels were below or close to 10 micrograms m-3. The pattern of the PCB in the workplace air was different from that of the sealant and contained higher levels of lighter components. The PCB concentrations in the indoor air were measured before and during the remedial process. The levels were around 600 ng m-3 and there was no significant increase during the removal of the sealant. The PCB level after the remedial action will be measured later. The pattern of the PCB in the indoor air was different from that of the sealant as well as from that of the workplace air. Higher levels of the lighter PCB were present indoors compared to the composition in both workplace air and in sealant. Extracts of PCB were analysed by GC-MS with a SIM method (selected ion monitoring). Standard procedures were used for extraction of solid materials. For the air samples an OVS tube was used with XAD-2 as adsorbent. The filter and adsorbent were extracted with toluene. This work shows that it is important to perform remedial action of PCB-containing elastic sealant as: (1) there is a spread of PCB to the indoor air giving high enough concentrations to make this the main PCB load on humans living in the apartments studied in this project; (2) large amounts are spread to the soil from these sealants; and (3) many of the PCB-containing elastic sealants used need to be changed from a functional perspective.     

Remobilization of polychlorinated biphenyls from sediment and its consequences for their transport in river waters

A laboratory experiment was performed to examine the remobilization of indicator polychlorinated biphenyls (iPCBs) from sediments and its results were applied to the real-world data for explaining the transport of PCBs in river. Seven PCB concentrations were determined in three series of model water–sediment systems (3 g of river sediment, three different volumes of distilled water (0.5, 0.25, and 0.15 ml), and 5 mg of biocide) after 11 days of incubation. Solid-phase extraction was used for separation of analytes from the aqueous phase and solvent extraction for isolation of analytes from the sediments, respectively. The extracts were analyzed for individual iPCB congeners using gas chromatography–mass spectrometry method. For each series of the experiment, the concentrations of PCBs in aqueous phase were similar. The average sediment/water partition coefficient value was 10⁴?l/kg. The solubility of individual PCB congeners in water did not influence the desorption of PCBs from the sediment. Although the dominant form of PCBs in a water–sediment system occurs as suspended and colloidal fractions, these compounds are transported mostly in a dissolved form. Suspended and colloidal matter is a major sink for PCBs in low-energy aquatic environments. In contrast, the dissolved PCBs are readily transported in running waters. The mobilization of PCBs from sediments to aqueous phase, with respect to their solubility in water, seems to be limited, thus reducing the risk of secondary pollution.     

液相色谱-串联质谱法测定水体、沉积物及土壤中全氟化合物

建立了水、沉积物及土壤中13种全氟化合物(PFCs)的富集、净化、浓缩的前处理方法及快速液相色谱三重四级杆串联质谱的分析方法。9种全氟羧酸、2种典型全氟磺酸、2种磺酰铵衍生前体物的响应因子与质量浓度的线性关系良好。添加回收实验表明,13种全氟化合物在水、土壤和沉积物中的回收率为52.3%~119.3%,变异系数为2.3%~19.4%,方法检出限分别为0.015~0.472 ng/L、0.012~0.875 ng/g、0.004~0.743 ng/g。该法成功应用于实际样品的测定,沉积物和土壤中分别检测到3种和10种全氟化合物。     

PAH and PCB in soils of Switzerland--status and critical review

The surface soil concentrations (0-20 cm) of the Swiss soil monitoring network (NABO) with 105 observation sites representing all major land use types ranged for the sum of 16 EPA PAH (PAH(16)) from 32 to 8465 microg kg(-1) (median 163 microg kg(-1)), for benzo[a]pyrene (BaP) from 0.5 to 1129 microg kg(-1) (median 13 microg kg(-1)) and for the sum of seven IRMM PCB (PCB(7)) from 0.5 to 12 microg kg(-1) (median 1.6 microg kg(-1)). The legal guide values of Switzerland were exceeded for PAH(16) at only three and for BaP at two sites. The PCB(7) concentrations were clearly below any assessment value. The concentration ranges were overlapping between all land use types. Tendencies for higher concentrations were observed at urban and viticulture sites. The overall measurement precision at repeatability conditions ranged from 1 to 37% RSD for PAH(16), BaP and PCB(7). The median bias for the chemical analysis was around zero for PAH(16), +5% for BaP and -5% for PCB(7) with spreads ranging from less than -20% up to more than +30%. The PAH profiles were clearly dominated by phenanthrene. Stratification by land use revealed a prevalence of benzo[a]pyrene at urban and naphthalene at conservation sites. For PCB, the general congener rank order was PCB no. 153 > 138 > 101 > 180. From a broad correlation screening only PAH(16)/BaP (r = 0.88**) were relevant for practical soil protection. The extensive comparison with other studies was severely biased by the lack of harmonisation, especially concerning sampling depth, sampling support, analytical method and the sum calculation procedure.     

Development and application of microwave assisted extraction (MAE) for the extraction of five polycyclic aromatic hydrocarbons in sediment samples in Johannesburg area, South Africa

A microwave-assisted extraction (MAE) method was verified and applied for the extraction of polycyclic aromatic hydrocarbons (PAHs) in sediment samples. Soxhlet extraction was used as the reference method. The optimum MAE was carried out with 20 mL of hexane/acetone (1:1, v/v) mixture in a 1-g sample at 250 W for 20 min. Soxhlet extraction was carried out with 250 mL of dichloromethane:hexane (1:1, v/v) mixture in a 15-g sample for 24 h in a water bath maintained at 60 °C. The collected extracts were both cleaned up, reduced to 1 mL under nitrogen and then injected into an HPLC fluorescence. To increase the sample throughput, simultaneous MAE was performed. The obtained percentage recoveries ranged from 61 to 93 and 88–98 for MAE and SE, respectively. The optimised MAE method was validated using certified reference material. It was then applied to real sediment samples from in and around the greater Johannesburg area. The sediments from Jukskei River were found to be the most polluted while Hartbeespoort Dam sediments were found to be least polluted. The overall order of concentrations for the studied PAHs per site was as follows: Jukskei River?>?Kempton Park?>?Centurion Dams?>?Natalspruit River (PIT)?>?Hartbeespoort Dam.     

Congener profiles of polychlorinated biphenyls in core sediments of Sunderban mangrove wetland (N.E. India) and their ecotoxicological significance

The paper presents the first comprehensive survey of congener profiles of polychlorinated biphenyls (PCBs) in core sediment samples (<63 microm particle size) covering seven sites in Sunderban mangrove Wetland, north-eastern part of the Bay of Bengal. Results pointed out a non-homogenous contamination of the wetland with Sigma23PCB values ranging from 0.5 to 26.9 ng g(-1) dry weight, reflecting very low to moderate contamination closely in conformity to other Asian coastal environment. The general decreasing order of the dominant congeners to the total load was: CB138 > 153 > 149 > 101, indicating the predominance of hexa-chlorinated congeners. The spatial distribution revealed significant differences in concentration related to local urbanization with industrial and land-based sources. No uniform temporal trend on PCB levels was recorded probably due to particular hydrological characteristics of the wetland and/or non-homogenous inputs from point sources. Strong positive correlations between the seven dominant congeners suggest their common sources and similar environmental behaviors. These results were also used for a risk assessment evaluation in the Sunderban wetland, showing that the present PCB levels were exceeding in few cases the lower limit of sediment quality guidelines of Environmental Protection Agency and Canadian Council of Ministers of the Environment.