Virtual phosphorus ore requirement of Japanese economy

Phosphorus is indispensable for agricultural production. Hence, the consumption of imported food indirectly implies the import of phosphorus resources. The global consumption of agricultural products depends on a small number of ore-producing countries. For sustainable management of phosphorus resources, the global supply and demand network should be clarified. In this study, we propose the virtual phosphorus ore requirement as a new indicator of the direct and indirect phosphorus requirements for our society. The virtual phosphorus ore requirement indicates the direct and indirect demands for phosphorus ore transformed into agricultural products and fertilizer. In this study, the virtual phosphorus ore requirement was evaluated for the Japanese economy in 2005. Importantly, the results show that our society requires twice as much phosphorus ore as the domestic demand for fertilizer production. The phosphorus contained in “eaten” agricultural products was only 12% of virtual phosphorus ore requirement.     

软锰矿电化学协同作用对活性嫩黄模拟废水脱色率的研究

以活性嫩黄K 4G模拟废水为处理对象 ,采用软锰矿与电化学协同法 ,分别在不同软锰矿加入量、电流密度、pH值、电解时间、染料初始浓度条件下进行电解实验 ,考察了各种因素对脱色率的影响。结果表明 ,增加软锰矿的用量、增大电流密度、降低pH值、延长电解时间都能提高脱色率 ,染料初始浓度对脱色率影响不显著。溶液中溶解态锰的浓度的变化表明 ,Mn(II)在处理过程中表现出催化作用 ,外加电压可强化软锰矿的氧化作用     

Biogeometallurgical pre-mining characterization of ore deposits: an approach to increase sustainability in the mining process

Based on the knowledge obtained from acid mine drainage formation in mine waste environments (tailings impoundments and waste rock dumps), a new methodology is applied to characterize new ore deposits before exploitation starts. This gives the opportunity to design optimized processes for metal recovery of the different mineral assemblages in an ore deposit and at the same time to minimize the environmental impact and costs downstream for mine waste management. Additionally, the whole economic potential is evaluated including strategic elements. The methodology integrates high-resolution geochemistry by sequential extractions and quantitative mineralogy in combination with kinetic bioleach tests. The produced data set allows to define biogeometallurgical units in the ore deposit and to predict the behavior of each element, economically or environmentally relevant, along the mining process.     

高碱度钢渣添加铁尾矿消解f-CaO的机理研究

高碱度钢渣掺唐山石人沟铁尾矿重构,两者在高温环境下熔融反应消解高碱度钢渣中f-CaO。采用正交实验法设计实验方案,考察了铁尾矿掺入量(分别为3%、5%和9%)、反应温度(分别为1 500℃,1 550℃和1 580℃)及恒温反应时间(分别为10 min、20 min和30 min)对消解高碱度钢渣中f-CaO的效果。实验结果表明,铁尾矿能有效消解钢渣中f-CaO,重构渣中f-CaO含量平均值为1.17%,消解率为76.27%。且由正交方法测出了铁尾矿掺入量对f-CaO的消解影响较大,极差值为0.41%;反应温度次之,极差值为0.32%;恒温反应时间影响较小,极差值为0.06%。利用X射线衍射方法测定重构渣中矿物组成,主要为磁铁矿、钙镁橄榄石、硅酸二钙、硅酸三钙、镁铁尖晶石、铁酸钙及铁铝酸钙。     

天然锰矿催化臭氧氧化降解水中4-氯酚的研究

以天然锰矿为金属催化剂,研究了锰矿催化臭氧氧化水中4-氯酚的降解效果。采用毛细管电泳方法及色质联用技术．分别对反应的中间产物和终产物进行了分析。推测了锰矿催化臭氧氧化水中4-氯酚的降解反应机理可能为：锰矿的吸附氧化与锰矿生成的Mn^2 催化臭氧分解．产生更多高活性的羟基自由基．从而提高了臭氧的氧化能力。     

Natural manganese ore catalyst for low-temperature selective catalytic reduction of NO with NH3 in coke-oven flue gas

Environmental Science and Pollution Research - Different types of manganese ore raw materials were prepared for use as catalysts, and the effects of different manganese ore raw materials and...     

Assessment of 222Rn emanation from ore body and backfill tailings in low-grade underground uranium mine

This paper presents a comparative study of ²²²Rn emanation from the ore and backfill tailings in an underground uranium mine located at Jaduguda, India. The effects of surface area, porosity, ²²⁶Ra and moisture contents on ²²²Rn emanation rate were examined. The study revealed that the bulk porosity of backfill tailings is more than two orders of magnitude than that of the ore. The geometric mean radon emanation rates from the ore body and backfill tailings were found to be 10.01?×?10^?3 and 1.03 Bq m^?2 s^?1, respectively. Significant positive linear correlations between ²²²Rn emanation rate and the ²²⁶Ra content of ore and tailings were observed. For normalised ²²⁶Ra content, the ²²²Rn emanation rate from tailings was found to be 283 times higher than the ore due to higher bulk porosity and surface area. The relative radon emanation from the tailings with moisture fraction of 0.14 was found to be 2.4 times higher than the oven-dried tailings. The study suggested that the mill tailings used as a backfill material significantly contributes to radon emanation as compared to the ore body itself and the ²²⁶Ra content and bulk porosity are the dominant factors for radon emanation into the mine atmosphere.     

选矿废水的回用处理研究与实践

铅锌矿泡沫浮选废水含有大量Pb2 + 离子和有机硫化物 ,经过混凝沉淀和活性炭吸附 ,去除其中的悬浮物、重金属离子和部分COD、降低其起泡性 ,然后回用生产。回用实践证明 ,选矿废水经过上述工艺处理后 ,其浮选选别指标与洁净水基本一致     

Atmospheric emission of polychlorinated naphthalenes from iron ore sintering processes

Iron ore sintering processes constitute significant sources of dioxins, and studies have confirmed a close correlation between polychlorinated naphthalenes (PCNs) and dioxin formation. Thus, iron ore sintering processes are thought to be a potential source of PCNs, although intensive investigations on PCN emissions from sintering processes have not been carried out. Therefore, the aim of the present study was to qualify and quantify PCN emissions from nine sintering plants operating on different industrial scales. PCN concentrations ranged from 3 to 983 ng m⁻³ (0.4-23.3 pg TEQ_PCN m⁻³) and emission factors ranged from 14 to 1749 μg t⁻¹ (0.5-41.5 ng TEQ_PCN t⁻¹), with a geometric mean of 84 μg t⁻¹ (2.1 ng TEQ_PCN t⁻¹). The estimated annual emission of PCNs from sintering processes in China was 1390 mg TEQ_PCN. These figures will assist in the development of a PCN emissions inventory. Regarding emission characteristics, PCNs mainly comprised low-chlorinated homologs. The ratios of several characteristic PCN congeners were also measured and compared with those from other sources. Taken together, these results may provide useful information for identifying the sources of PCNs produced by iron ore sintering processes.     

Study on the mechanism and kinetics of manganese release from waste manganese ore waste rock under rainfall leaching

Environmental Science and Pollution Research - Manganese released from the piled manganese ore wastes is a great threat to the local ecosystem and human health. The mechanism and dynamic...     

非定态SO2制酸工艺在铅精矿烧结烟气治理中的应用

介绍了非定态SO2制酸工艺的特点、流程及其在铅精矿烧结烟气治理中的应用效果.该工艺具有良好的社会效益、环境效益和较好的经济效益,具有较高的推广应用价值.     

PCDD/F and "Dioxin-like" PCB emissions from iron ore sintering plants in the UK

Investigations have been carried out at the three Corus UK sinter plants over the period 2002-2004 to characterise the emissions of both 2,3,7,8-PCDD/Fs and WHO-12 PCBs, to estimate annual mass releases of these organic micro-pollutants using the I-TEF and WHO-TEF schemes, and to investigate the formation of PCBs in the iron ore sintering process. Results showed that the sintering of iron ore produces a characteristic WHO-12 PCB and PCDD/F congener pattern that is substantially the same for all UK sinter plants. With regard to WHO-12 PCBs, the most abundant congeners were typically PCBs 118 (6-9 ngNm(-3)), 105 (2-4 ngNm(-3)) and 77 (2-3 ngNm(-3)). All other WHO-12 PCBs were also detected at concentrations around 1 ngNm(-3). All sinter plants investigated exhibited very similar TEQ concentrations. WHO-12 PCB emissions were in the range 0.042-0.111 ngWHO-TEQNm(-3), whereas PCDD/F emissions ranged from 0.39 to 1.62 ngWHO-TEQNm(-3). PCDF congeners were the main contributors to the overall TEQ in sintering emissions (ca. 85%). Amongst WHO-12 PCBs, PCB 126 was the only noteworthy contributor to total TEQ (ca. 5-7%), a similar contribution to that from PCDDs. Based on the measurements that Corus UK has undertaken at these three sinter plants, annual mass releases of WHO-12 PCBs and PCDD/Fs have been calculated. For UK sinter plants, a total mass release of 29.5 g WHO-TEQ per annum [WHO-12 PCBs+PCDD/Fs] has been estimated, representing 9% of the total PCDD/F emissions to the UK atmosphere. Measurements were also carried out at a UK sinter plant to determine the windleg emission profile of WHO-12 PCBs. Results showed that WHO-12 PCBs were formed in the same regions of the sinter strand as 2,3,7,8-PCDD/Fs, indicating that there was a strong correlation between the formation of WHO-12 PCBs and PCDD/Fs in the iron ore sintering process.     

Enhanced activated persulfate oxidation of ciprofloxacin using a low-grade titanium ore under sunlight: influence of the irradiation source on its transformation products

Environmental Science and Pollution Research - In this work, the activated persulfate oxidation of ciprofloxacin (CIP) using a low-grade titanium ore under sunlight or simulated sunlight were...     

<Emphasis Type="Bold">Tracing lead contamination in foods in the city of Kolkata,India</Emphasis>

Lead isotopic ratios (LIR) of eight common food items, street dust, coal, diesel, sediments, lead ore and rainwater from India have been reported for the first time in this paper. This study characterized the source and extent of lead pollution in the different foodstuff consumed in Kolkata, a major metropolis of eastern India. The atmospheric lead input to the food items, sold openly in busy roadside markets of the city, has been quantified. The mean 207/206 and 208/206 LIRs of the eight food items ranged from 0.8847 to 0.8924 and 2.145 to 2.167, respectively. Diesel had the highest mean 207/206 and 208/206 values of 0.9015 and 2.1869, respectively, apart from the lead ore. The food items had a mean lead concentration between 3.78 and 43.35 mg kg^?1. The two ratio scatter plots of all the different environmental matrices were spread linearly between the uncontaminated Ichapur sediment and diesel. The 207/206 LIRs of the coal with a mean of 0.8777 did not fall in the linear trend, while the street dust and food samples overlapped strongly. The rainwater sample had a 207/206 LIR of 0.9007. Contaminated sediments in Dhapa, the repository of the city’s municipal garbage, had a mean 207/206 LIR of 0.8658. The corresponding value obtained from the sewage-fed vegetable grown there was 0.8058. The present study indicated that diesel was one of the main contributor to Pb pollution. The atmospheric lead contribution to the food items was in the range of 68.48–86.66 %.     

Assessment of metal availability to vegetation (Betula pendula) in Pb-Zn ore concentrate residues with different features

In this work, characterisation of several ore concentrate remains from an abandoned Pb-Zn mining factory was performed determining chemical and physical properties such as pH, organic carbon content, particle size distribution, total heavy metal content (Pb, Zn, Cu, As and Cd) as well as mineralogical composition which showed, in most cases, the oxidization of the parent ore material (mostly galena: PbS and sphalerite: ZnS) to more mobile fractions as anglesite (PbSO(4)) and goslarite (ZnSO(4)). Moreover, two operational defined extraction procedures commonly used in soil and sediment studies (first and second steps of BCR procedure and DTPA extraction protocol) were applied in the different mining wastes in order to study Pb and Zn mobility and likely bioavailability to Betula pendula growing on the same mining spoils, which presents lead and zinc contents in leaves over ten times background values.     

碳酰肼对烧结过程二噁英生成的抑制作用

研究了碳酰肼对钢铁厂烧结工序产生的二噁英的抑制效果。结果表明,添加了0.01%(质量分数,下同)、0.02%、0.05%、0.10%的碳酰肼之后,二噁英的排放质量浓度降为0.560、0.506、0.270、0.174ng-TEQ/m3,相对于基准值(0.821ng-TEQ/m3)大幅减少。碳酰肼对二噁英的从头合成以及前驱物生成都能起到一定的抑制效果。碳酰肼与Cu2+结合生成稳定的氮化物,削弱Cu2+的催化活性;与HCl反应,减少了生成二噁英的氯源;对FeCl3、CuCl2的催化活性也会产生影响。碳酰肼添加后,对多氯代二苯并呋喃(PCDFs)生成中高氯代二噁英的脱氯行为也有明显的抑制。     

Dioxins from thermal and metallurgical processes: recent studies for the iron and steel industry

In thermal metallurgical processes such as iron ore sintering and metal smelting operations, large flows of off-gases are generated. Mainly due to residue recycling in such processes, chlorine and volatile organics are always present in the feed. As a consequence of "de novo" formation, the off-gases from such processes typically contain dioxins in the range 0.3-30 ng I-TEQ/Nm3. So far there are only very few studies about the mechanisms of dioxin formation and destruction in these metallurgical processes. In an European Union (EU) research project "Minimization of dioxins in thermal industrial processes: mechanisms, monitoring and abatement (MINIDIP)", integrated iron and steel plant has been selected as one of the industrial sectors for further investigation. A large number of particulate samples (feed, belt siftings, electrofilter) were collected from the iron ore sintering installations from various steel plants and analyzed for their organochlorocompound contents. Measurable amounts of PCDD/F, PCBz, PCB were found for all samples. The various parameters influencing their de novo synthesis activity were also evaluated in laboratory experiments, and such activity was found to be moderate for samples from the ore sinter belt, but extremely high for some ESP dusts. Fine dust is active in a wide range of temperatures starting at 200 degrees C and declining above 450 degrees C; the optimal temperature for de novo synthesis was found to be around 350 degrees C; some inhibitors, such as triethanolamine, may reduce de novo activity by 50%, and lowering the O2 concentration in the gas stream leads to a much lower amount of PCDD/F formation. On the basis of their relative mass, typical operating conditions and specific activity of the different samples, the regions in the sintering plant where de novo synthesis may take place were tentatively established.     

Variation of dust layer height in the northern Taklimakan Desert in April 2002

LIDAR observations were conducted in the northern Taklimakan Desert to investigate the vertical distribution of dust in April 2002. During the observation period, a dust outbreak occurred on 13 April, remaining over the desert for several days. Despite only slight variations being observed in dust layer height before the dust event, marked diurnal variation in dust layer height was observed after the dust event. In this study, we conducted two numerical simulations to investigate differences in the variation exhibited by the dust layer heights before and after the dust event, and assessed the influence of meteorological conditions on this variation. The simulated results show that the clearly diurnal variation in dust layer height is strongly influenced by local circulation which is affected by the characteristic topography and synoptic conditions of the Tarim Basin.     

Chemical mass balance source apportionment for combined PM2.5 measurements from U.S. non-urban and urban long-term networks

The Minnesota Particulate Matter 2.5 (PM_2.5) Source Apportionment Study was undertaken to explore the utility of PM_2.5 mass, element, ion, and carbon measurements from long-term speciation networks for pollution source attribution. Ambient monitoring data at eight sites across the state were retrieved from the archives of the Interagency Monitoring of Protected Visual Environments (IMPROVE) and the Speciation Trends Network (STN; part of the Chemical Speciation Network [CSN]) and analyzed by an Effective Variance – Chemical Mass Balance (EV-CMB) receptor model with region-specific geological source profiles developed in this study. PM_2.5 was apportioned into contributions of fugitive soil dust, calcium-rich dust, taconite (low grade iron ore) dust, road salt, motor vehicle exhaust, biomass burning, coal-fired utility, and secondary aerosol. Secondary sulfate and nitrate contributed strongly (49–71% of PM_2.5) across all sites and was dominant (≥60%) at IMPROVE sites. Vehicle exhausts accounted for 20–70% of the primary PM_2.5 contribution, largely exceeding the proportion in the primary PM_2.5 emission inventory. The diesel exhaust contribution was separable from the gasoline engine exhaust contribution at the STN sites. Higher detection limits for several marker elements in the STN resulted in non-detectable coal-fired boiler contributions which were detected in the IMPROVE data. Despite the different measured variables, analytical methods, and detection limits, EV-CMB results from a nearby IMPROVE-STN non-urban/urban sites showed similar contributions from regional sources – including fugitive dust and secondary aerosol. Seasonal variations of source contributions were examined and extreme PM_2.5 episodes were explained by both local and regional pollution events.     

Mineral dust is a sink for chlorine in the marine boundary layer

Dust particles affect the budgets of important traces gases by providing a surface on which heterogeneous reactions can occur. The uptake of soluble species on dust alters the physical, chemical, and optical properties and the overall ability of dust to act as cloud condensation and ice nuclei. It is commonly assumed that all measured chloride in particulate filter samples is associated with sea-salt particles and any chloride in dust occurs as the result of internal mixtures of sea-salt and dust particles, formed by cloud processing. Here we show high temporal resolution data demonstrating the direct uptake of chlorine by dust via heterogeneous reaction with HCl(g). This reaction added significant amounts of chlorine to the dust particles during a major dust storm, representing 4–9% of the individual dust particle mass. Up to 65±4% of the dust particles contained chlorine due to this heterogeneous reaction during the dust front. Ignoring this process leads to an overestimation of sea-salt concentrations from bulk measurements, and an underestimation of the degree of sea-salt aging. The uptake of chloride will change the pH and hygroscopic properties of the dust and thus can influence the budgets of other reactive gases. Including this heterogeneous process in atmospheric measurements and chemical transport models will improve our ability to predict the atmosphere's composition and radiation budget with greater accuracy.