生活垃圾分选线上柔性破袋机的原理与设计

通过设计高速柔性破袋机并在垃圾分选生产线上进行实验,系统探索了整机构造、鞭具、转辊以及安装位置等重要因素对破袋效果和稳定性的影响,得出了最优鞭型为直径ϕ3~6 mm的钢丝绳,在鞭具根部固定方式保持不小于30°的环向自由度时,可消除疲劳,鞭具最优线速度为10~20 m·s-1。柔性破袋机结构轻简、能耗低,其破袋效果可满足生活垃圾分选线的要求。在防缠方面,相对于鞭具静止的辊子壁面防缠效果更明显。柔性破袋机可以骑跨在输送设备上,在分选线上多点布置,达到破袋率累积的效果。柔性破袋机布置在水平料流面上方时,要比布置在直立料流面一侧防缠效果更好。     

城市生活垃圾与园林废弃物的共热解特性

为实现城市生活垃圾减量化、无害化和资源化,采用热重分析天平和实验室固定床热解反应器进行城市生活垃圾（MSW）与园林废弃物共热解实验,研究了不同热解终温、松树枝和柳树枝添加比例对热解产物产率影响,并利用气质联用色谱分析仪（GC-MS）对热解油进行表征分析。实验结果表明：MSW、松树枝和柳树枝的热解过程均可以分为3个阶段,主要包括脱水、热解、炭化;MSW、松树枝和柳树枝单独热解时最大失重速率分别出现在321.48、358.23和377.83℃;MSW与松树枝共热解DTG曲线在热解反应第2阶段有2个析出峰,分别在342.32℃和471.48℃,比MSW单独热解时,失重率增加了7.29%。当城市生活垃圾与松树枝、柳树枝的添加量分别为3：1时,热解液体产物产率明显升高,热解油中醇类、羧酸类、醛类等含氧有机物的含量降低,热值增加,热解油中氧含量降低,且松树枝对共热解焦油的脱氧效果更为显著,热解油品质得到提升。     

Composting of municipal solid waste by different methods improved the growth of vegetables and reduced the health risks of cadmium and lead

Environmental Science and Pollution Research - Reutilization of putrescible municipal solid wastes (MSW) in agriculture can provide valuable plant nutrients. However, it may pose serious...     

市政污泥与生活垃圾混烧技术验证简

对市政污泥与生活垃圾混烧进行了验证研究。结果表明,与生活垃圾单独焚烧相比,污泥与生活垃圾混烧后烟气中NO_x、CO和HCl的浓度没有出现明显变化,而SO₂浓度出现了下降（从82~93 mg/m³下降至41~70 mg/m³）;Hg、Pb、Sn、Cr和Zn的浓度均表现为不同程度的上升,但仍然符合GB18485;二恶英从0.0087 ng TEQ/m³降至0.0047 ng TEQ/m³。掺烧半干污泥比例为10%、12%和15%时,吨物质的发电量分别为311.8 kWh/t、306.7 kWh/t和296.1 kWh/t。混烧污泥在一定程度上降低了系统的发电量,因此建议混烧污泥的比例不应大于15%。测算的污泥混烧成本约209元/t（80%含水率）。     

市政污泥与生活垃圾混烧技术验证

对市政污泥与生活垃圾混烧进行了验证研究。结果表明,与生活垃圾单独焚烧相比,污泥与生活垃圾混烧后烟气中NOx、CO和HCl的浓度没有出现明显变化,而SO2浓度出现了下降（从82～93mg／m3下降至41～70mg／m3）;Hg、Pb、Sn、Cr和Zn的浓度均表现为不同程度的上升,但仍然符合GB[g485;二恶英从0．0087μgTEQ／m3降至O．0047μgTEQ／m3。掺烧半干污泥比例为10％、12％和15％时,吨物质的发电量分别为311．8kWh／t、306．7kWh／t和296．1kwh／t。混烧污泥在一定程度上降低了系统的发电量,因此建议混烧污泥的比例不应大于15％。测算的污泥混烧成本约209元／t（80％含水率）。     

Evaluating the dual porosity of landfilled municipal solid waste

Environmental Science and Pollution Research - The objective of this paper was to study the pore-size distribution of municipal solid waste (MSW) and provide a basis for understanding the mechanism...     

生活垃圾堆肥工艺条件及其反应动力学研究

为了改善堆肥微环境 ,提高生活垃圾堆肥速率 ,研究堆肥工艺条件及其反应动力学是非常必要的。通过控制堆肥工艺条件 ,如初始温度、含水率、C/N比及堆料颗粒大小 ,研究生活垃圾堆肥过程中生物、化学及物理因素的变化。试验结果表明 ,生活垃圾堆肥反应符合一级反应动力学 ;合理控制堆肥初始反应条件 ,能明显提高堆肥效率。     

广州李坑生活垃圾填埋场周围植被现状调查与影响分析

为对垃圾填埋场封场后如何进行生态恢复研究提供基础资料，对超负荷运转中的广州市李坑生活垃圾填埋场周围的植被现状进行了调查，测算了物种量、覆盖度、污染状况等。同时运用植被覆盖度、结构、物种量和相对物种量等级评价以及对Zn、Cd等6种污染物的质量指数进行了评价。结果表明，所调查填埋场场区及灌区内有轻度污染，而场外与灌区外则相对较轻或无污染。     

Comparison of aerobic and anaerobic biotreatment of municipal solid waste

To increase the operating lifetime of landfills and to lower leachate treatment costs, an increasing number of municipal solid waste (MSW) landfills are being managed as either aerobic or anaerobic bioreactors. Landfill gas composition, respiration rates, and subsidence were measured for 400 days in 200-L tanks filled with fresh waste materials to compare the relative effectiveness of the two treatments. Tanks were prepared to provide the following conditions: (1) air injection and leachate recirculation (aerobic), (2) leachate recirculation (anaerobic), and (3) no treatment (anaerobic). Respiration tests on the aerobic wet tank showed a steady decrease in oxygen consumption rates from 1.3 mol/day at 20 days to 0.1 mol/day at 400 days. Aerobic wet tanks produced, on average, 6 mol of carbon dioxide (CO2)/kg of MSW as compared with anaerobic wet tanks, which produced 2.2 mol methane/kg of MSW and 2.0 mol CO2/kg methane. Over the test period, the aerobic tanks settled on average 35%, anaerobic tanks settled 21.7%, and the no-treatment tank settled 7.5%, equivalent to overall mass loss in the corresponding reactors. Aerobic tanks reduced stabilization time and produced negligible odor compared with anaerobic tanks, possibly because of the 2 orders of magnitude lower leachate ammonia levels in the aerobic tank. Both treatment regimes provide the opportunity for disposal and remediation of liquid waste.     

Characterization of municipal solid waste incineration and flue gas emission under anoxic environment in Tibet Plateau

Environmental Science and Pollution Research - Waste incineration is a process of full combustion reaction between waste and oxygen at high temperature. It is a new problem whether the special...     

Desorption of PCDD/PCDF from municipal solid waste incinerator flyash under post-combustion plant conditions

The influence of temperature on the levels of PCDD and PCDF remaining in, and desorbed from, a municipal solid waste incinerator flyash was investigated by heating the ash to between 200 and 400 degrees C under a simulated flue gas for four days reaction time. Considerable desorption of PCDD/PCDF from the flyash was seen at 275 degrees C and above. Maximum desorption occurred at 350 degrees C, with the equivalent of nearly eight times the total PCDD/PCDF concentration of the original flyash being lost to the vapour phase per unit mass of initial flyash. The I-TEQ value of the desorbed PCDD/PCDF was considerable, being over fourteen times that of the original flyash at 325 degrees C. The results indicate that formation of PCDD/PCDF on flyash deposits in the post-combustion plant of incinerators can result in the release of significant amounts of PCDD/PCDF to the flue gas stream.     

COVID-19 and municipal solid waste (MSW) management: a review

Environmental Science and Pollution Research - Municipal solid waste (MSW) represents an inevitable by-product of human activity and a major crisis for communities across the globe. In recent...     

Experimental study on the pore and solid structures of municipal solid waste under compression based on computed tomography (CT) scans

Environmental Science and Pollution Research - Municipal solid waste (MSW) is a highly heterogeneous porous medium that contains a variety of components and has complex pores and solid structures....     

滚筒筛筛分生活垃圾的理论研究

滚筒筛是生活垃圾分选中常用的工具,但筛分理论目前还不够清楚,导致滚筒筛的设计多依靠经验进行。从生活垃圾在滚筒筛内的受力分析着手,考虑了物料与滚筒筛筛壁间的摩擦力,其为一有限值,推导出物料的提升角与滚筒筛转速的关系,且物料提升角的大小取决于物料静摩擦角的大小;认为无论滚筒筛的转速多大,物料的最大提升角都是固定不变的。经过一系列分析得出与已有的垃圾滚筒筛理论不同的结论：滚筒筛是否存在临界转速,取决于被筛分的物料：物料的静摩擦角≥90°,滚筒筛存在临界转速;否则,滚筒筛不存在临界转速。这一结论对滚筒筛的设计具有理论上的指导意义。     

Sources and fates of lead and cadmium in municipal solid waste

Lead and cadmium enter the municipal solid waste stream as components of a variety of consumer products. Average empirical data from several resource recovery plants were analyzed to obtain an estimate of the source and fate of the subject elements. The total amounts of lead and cadmium found in municipal solid waste, determined from empirical data sources, were found to agree closely with those based on materials flow data. It was determined that most of the cadmium enters the waste stream in the combustible fraction and can account for a major share of the cadmium observed in fly ash and in atmospheric particulates. The most likely sources of cadmium are plastics and pigments. The lead emissions appeared to be derived from both combustible and noncombustible discards of batteries, plastics, and pigments. The data suggests that it would be useful to perform mass balance studies to provide primary data for the determination of the most effective methods for managing discards containing lead and cadmium. The purpose of the suggested research is the reduction of lead and cadmium emissions into the environment from resource recovery plants.     

季节性城市生活垃圾成分分析及厌氧消化特性研究

城市生活垃圾的成分及特性随着季节和人类在不同季节的生活习惯而变化,针对我国北方城市研究了一年中不同季节的城市生活垃圾成分特点,对影响厌氧发酵过程的相关成分如总有机碳（TOC）、总氮（TN）、蛋白质、脂肪和还原糖等进行了测定分析。通过厌氧消化实验,测得不同季节城市生活垃圾pH值、日产气量、沼气甲烷含量、甲烷累积量、挥发性脂肪酸（VFAs）和氧化还原电位（ORP）等参数的变化规律,分析相应变化的影响因素。结果表明,二、三季度的含水率分别为64．81％和67．50％,高于一、四季度,一季度发酵原料中蛋白质和脂肪含量分别为12．56％和8．86％,明显高于其他3个季度。一季度甲烷累积量最高,达到17616mL,单位发酵原料的产气量为204．8mL／g,也是4个季度中最高的,说明蛋白质、脂肪等有机成分含量对厌氧发酵过程及结果影响比较明显。为进一步的城市生活垃圾厌氧消化制取生物燃气的工艺条件提供依据。     

垃圾填埋场甲烷氧化菌及甲烷通量的研究

采用静态箱法、滚管计数法和气相色谱法,对6个不同封场时间填埋区的甲烷通量、覆土层甲烷氧化菌数量和甲烷氧化速率的变化趋势进行了测定,并分析了它们与封场时间、植被覆盖率等因素之间的相关性。结果发现6个填埋区甲烷通量的变化范围在-0.34～5.31 mg/(m2.h)之间;覆土层甲烷氧化菌的数量范围为3.10×107～20.77×107 cfu/g干土,甲烷氧化速率在1.65×10-8～4.34×10-8mol/(h.g)之间。覆土层甲烷氧化菌的数量与甲烷氧化速率呈正相关,但前者并不是后者的决定性因素;甲烷通量高时可刺激甲烷氧化菌数量及氧化速率的提高,且三者均与封场时间呈显著负相关,与植被覆盖率呈负相关;当含水率大于15%时,随着覆土层含水率的增加,甲烷氧化速率呈下降趋势;覆土pH、有机质和铵态氮与甲烷氧化速率等无明显相关性。提高覆土层的甲烷氧化速率可有效减少垃圾填埋场的甲烷排放。     

Classification and comparison of municipal solid waste based on thermochemical characteristics

Municipal solid waste (MSW) has been normally sorted into six categories, namely, food residue, wood waste, paper, textiles, plastics, and rubber. In each category, materials could be classified further into subgroups. Based on proximate and ultimate analysis and heating value, statistical methods such as analysis of variance (ANOVA) and cluster analysis were applied to analyze the characteristics of MSW in every subgroup and to try to distinguish their relative properties. The chemical characteristics analysis of MSW showed that polyethylene (PE), polypropylene (PP), and polystyrene (PS) had the highest volatile matter content, with almost no ash and fixed carbon, while polyethylene terephthalate (PET) had high carbon content but low hydrogen content. Bones and vegetables had the highest ash content, while nutshells and rubber had the highest fixed carbon content. Paper and starch food had the highest oxygen content, and wool and bones had the highest nitrogen and sulfur content. Polyvinyl chloride (PVC) had the highest chlorine content at about 55%. PE, PP, and PS had the highest heating value, followed by chemical products such as rubber and chemical fiber. Conversely, paper, vegetables and bones had the lowest heating value. The results of cluster analysis of MSW components showed that fruit peel, weeds, wood, bamboo, leaves and nutshells could be classified as the lignocellulose category; starch food, cotton, toilet paper, printing paper and cardboard could be classified as the glucose monomer category; wood and chemical fiber could be classified as the high nitrogen and sulfur category; and PE, PP, and PS could be cluster as the polyolefin category.

Implications: The yield of municipal solid waste (MSW) is constantly increasing and waste to energy (WTE) has been used extensively all over the world. During the processes of incineration, pyrolysis, or gasification, the impact of physical and chemical properties of MSW is of great significance. However, the traditional classification of MSW is too general to provide more detailed information in many investigations. It is necessary to perform the investigation of characteristics of combustible MSW to distinguish different categories of MSW and find out their subclassification.     

台北市生活垃圾管理经验及启示

台北市生活垃圾管理效果显著,人均生活垃圾日清运量年均减量7.3%、资源回收率年均增长28.3%并带动资源回收产业发展、居民负担仅为1998年的22.0%、社会成本较1998年减少30.7%。主要经验包括:明确的生活垃圾减量与资源回收目标;系统的管理模式设计,包括政府(环保局、地方清洁队、资源回收管理基金)、生产商、回收商、处理商、居民、垃圾焚烧厂和填埋场以及第三方等主要干系人。采取的主要政策手段包括强制源头分类、随袋征收垃圾处理费、建立资源回收管理基金、对资源回收行业的政策扶持以及信息公开与公众参与等。台北市先进的生活垃圾管理经验对中国大陆城市开展垃圾分类与资源化管理具有重要的参考价值。