Chlorination of dibenzofuran and dibenzo-p-dioxin vapor by copper (II) chloride

Dibenzofuran (DF) is formed from phenol and benzene in combustion gas exhaust streams prior to particle collection equipment. Subsequent chlorination at lower temperatures on particle surfaces is a potential source of chlorinated dibenzofuran (CDF). Gas streams containing 8% O₂ and approximately 0.1% DF vapor were passed through particle beds containing copper (II) chloride (0.5% Cu, mass) at temperatures ranging from 200 to 400 °C to investigate the potential for CDF formation during particle collection. Experiment duration was sufficient to provide an excess amount of DF (DF/Cu=3). The efficiency of DF chlorination by CuCl₂ and the distribution of CDF products were measured, with effects of temperature, gas velocity, and experiment duration assessed. Results of a more limited investigation of dibenzo-p-dioxin (DD) chlorination by CuCl₂ to form chlorinated DD (CDD) products are also presented.

The efficiency of DF/DD chlorination by CuCl₂ was high, both in terms of CuCl₂ utilization and DF/DD conversion. Total yields of Cl on CDF/CDD products of up to 0.5 mole Cl per mole CuCl₂ were observed between 200 and 300 °C; this suggests that nearly 100% CuCl₂ was utilized, assuming a conversion of two moles of CuCl₂ to CuCl per mole Cl added to DD/DF. In a short duration experiment (DF/Cu=0.3), nearly 100% DF adsorption and conversion to CDF was achieved. The degree of CDF chlorination was strongly dependent on gas velocity. At high gas velocity, corresponding to a gas–particle contact time of 0.3 s, mono-CDF (MCDF) yield was largest, with yields decreasing with increasing CDF chlorination. At low gas velocity, corresponding to a gas–particle contact time of 5 s, octa-CDF yield was largest. DF/DD chlorination was strongly favored at lateral sites, with the predominant CDF/CDD isomers within each homologue group those containing Cl substituents at only the 2,3,7,8 positions. At the higher temperatures and lower gas velocities studied, however, broader isomer distributions, particularly of the less CDD/CDF products, were observed, likely due to preferential destruction of the 2,3,7,8 congeners.     

Reductive dechlorination of polychlorinated dibenzo-p-dioxins by zerovalent iron in subcritical water

A new method for reductive dechlorination of polychlorinated dibenzo-p-dioxins (PCDDs) and remediation of contaminated soils is described that uses zerovalent iron as the dechlorination agent and subcritical water as reaction medium and extractive solvent. It is found that the zerovalent iron can be applied for stepwise dechlorination of octachlorinated dibenzo-p-dioxin (OCDD) on various matrixes in subcritical water. By using iron powder as matrix higher chlorinated congeners were practically completely reduced to less than tetra-substituted homologues. A significant part of residual OCDD, when it was spiked in to soils, and formed less chlorinated congeners are extracted with water in the given conditions. The solubility of OCDD was increased by a 4–6 orders over its solubility at ambient conditions. The new method of contentious-flow extraction is described.     

Effects of copper chloride on formation of polychlorinated dibenzo-p-dioxins in model waste incineration

Combustion experiments in a laboratory-scale fluidized-bed reactor were conducted to elucidate the effects of copper chloride as a catalyst on polychlorinated dibenzo-p-dioxins (PCDDs) formation in municipal waste incineration. We used model wastes with and without copper chloride (CuCl₂ · 2H₂O), both of which contained polyvinyl chloride as a chlorine source. Combustion temperature was set to 900 °C, and the amount of air supplied was twice the stoichiometric ratio. The experimental setup was carefully planned to suppress the influences of experimental conditions except the waste composition. Results of these experiments showed that copper chloride in the waste increased the amount of PCDDs formed and made the homologue profile to shift towards the highly chlorinated species. Copper chloride contributes to the PCDDs formation by promoting chlorination, whereby the reaction is important in that organic matter is chlorinated directly by copper compounds. Copper chloride did not exert a great influence on the isomer distribution patterns of PCDDs, while there appeared a significant difference in the case of PCDFs. This points out the difference of the major formation mechanisms between PCDDs and PCDFs. PCDDs are less formed by the catalytic reactions from carbon/polycyclic aromatic hydrocarbons than PCDFs in our experimental conditions.     

Polychlorinated dibenzo-p-dioxins and related compounds: The blood levels of young Japanese women

We investigated PCDDs and related compounds in the blood of young Japanese women, approximately 20 years of age, who had not yet had children, and discussed how the TEQ level of PCDDs and related compounds in their blood may affect the next generation. Means of total TEQ levels were 0.063 pg/g for whole blood basis and 21 pg/g for lipid basis. TEQ of PCDDs, PCDFs and coplanar PCBs accounted for about 43, 34 and 23% of the total TEQ in the whole blood basis, respectively. In the lipid basis, their values were about 44, 34 and 22%, respectively. Previously, we investigated PCDDs and related compounds levels in mother's breast milk, lymphocyte subpopulation and thyroid function of their children, and found negative correlations between the TEQ level of PCDDs and related compounds and CD4+/CD8+, and/or the TEQ level of PCDDs and related compounds and the T₄ level in 36 mothers and children. Of these cases, the average age was approximately 28 years. PCDDs and related compounds may be related to immunopathy, such as atopic dermatitis. The effects of PCDDs and related compounds on babies of young Japanese women are important and must be further evaluated.     

Atmospheric oxidation mechanisms of polychlorinated dibenzo-p-dioxins are different from those of benzene and dibenzofuran: a theoretical prediction

The reaction mechanisms of dibenzo-p-dioxin (DD) and 2,3,7,8-TCDD with OH radical have been studied using density functional theory calculations. Under the atmospheric conditions, ca 42% of DD + OH reaction proceeds as formation of DD − OH-β adduct, which will react with O₂ slowly; while the rest will proceed as formation of DD − OH-γ adduct, which will decompose to the substituted phenoxy radical P1 by the fused-ring C-O bond cleavage. For 2,3,7,8-TCDD + OH, the reaction will predominantly form the substituted phenoxy radical P2. The reaction mechanisms are drastically different from the peroxy mechanism for the atmospheric oxidations of benzene and dibenzofuran.     

Effects of copper(II) and copper oxides on THMs formation in copper pipe

Little is known about how the growth of trihalomethanes (THMs) in drinking water is affected in copper pipe. The formation of THMs and chlorine consumption in copper pipe under stagnant flow conditions were investigated. Experiments for the same water held in glass bottles were performed for comparison. Results showed that although THMs levels firstly increased in the presence of chlorine in copper pipe, faster decay of chlorine as compared to the glass bottle affected the rate of THMs formation. The analysis of water phase was supplemented by surface analysis of corrosion scales using X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM) and energy dispersive spectroscopy (EDX). The results showed the scales on the pipe surface mainly consisted of Cu₂O, CuO and Cu(OH)₂ or CuCO₃. Designed experiments confirmed that the fast depletion of chlorine in copper pipe was mainly due to effect of Cu₂O, CuO in corrosion scales on copper pipe. Although copper(II) and copper oxides showed effect on THMs formation, the rapid consumption of chlorine due to copper oxide made THM levels lower than that in glass bottles after 4 h. The transformations of CF, DCBM and CDBM to BF were accelerated in the presence of copper(II), cupric oxide and cuprous oxide. The effect of pH on THMs formation was influenced by effect of pH on corrosion of copper pipe. When pH was below 7, THMs levels in copper pipe was higher as compared to glass bottle, but lower when pH was above 7.     

Particle size distributions and health-related exposures of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) of sinter plant workers

This study measured particle size distributions of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in two workplace atmospheres of the sintering grate and rough roll shredder in a sintering plant, and to assess their workers’ health-related exposures. We found that the PCDD/F concentration of the sintering grate (site A = 14.47 pg m⁻³) was lower than that of the rough roll shredder (site B = 17.20 pg m⁻³). Particle size distributions of PCDD/Fs were in the form of the unimodal with the mass median aerodynamic diameter (MMAD) of 4.74 μm and 5.23 μm, and geometric standard deviation (σ_g) of 3.15 and 2.15 for the site A and B, respectively. The above results suggest that the workplace of the site A had a less fraction of coarse particles than that of the site B. The estimated PCDD/F concentrations of the inhalable fraction (11.0 pg m⁻³) and thoracic fraction (8.89 pg m⁻³) of the site A were lower than those of the site B (12.4 and 9.39 pg m⁻³, respectively). But to the contrary the estimated respirable fraction of the site A (5.05 pg m⁻³) was slightly higher than that of the site B (4.93 pg m⁻³). Our results clearly indicate the importance to conduct particle size segregating samplings for assessing human PCDD/F exposures.     

Biosorption of copper(II) from aqueous solutions by pre-treated biomass of marine algae Padina sp

Biosorption of heavy metals can be an effective process for the removal and recovery of heavy metal ions from aqueous solutions. The biomass of marine algae has been reported to have high uptake capacities for a number of heavy metal ions. In this paper, the adsorption properties of a pre-treated biomass of marine algae Padina sp. for copper(II) were investigated. Equilibrium isotherms and kinetics were obtained from batch adsorption experiments. The biosorption capacities were solution pH dependent and the maximum capacity obtained was 0.80 mmol/g at a solution pH of about 5. The biosorption kinetics was found to be fast, with 90% of adsorption within 15 min and equilibrium reached at 30 min. The effects of light metal ions on copper(II) uptake were studied and the presence of light metal ions did not affect copper(II) uptake significantly. Fixed-bed breakthrough curves for copper(II) removal were also obtained. This study demonstrated that the pre-treated biomass of Padina sp. could be used as an effective biosorbent for the treatment of copper(II) containing wastewater streams.     

Colloid facilitated transport of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) to the groundwater at Ma Da Area, Vietnam

PCDD/Fs are hydrophobic organic substances and strongly sorbing to soil particles. Once adsorbed to soil particles they are believed to be virtually immobile. However, research in the last decades confirmed that strong sorbing contaminants may reach the groundwater via colloid-facilitated transport. This pathway has not been investigated before in Vietnam. Ma Da area, 100 km north of Ho Chi Minh City, was repeatedly sprayed during the Vietnam War (1962–1971) with herbicides like Agent Orange containing, beside others, the teratogenic contaminant 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD). 11 surface soil samples and 12 water samples were collected in Ma Da area for analysis of PCDD/Fs in solids. Soil TCDD concentrations ranged from 1–41 ppt with a mean of 8.8 ppt and a mean I-TEQ of 9.7 ppt. Two surface water samples showed colloid bound TCDD (7 and 19 ppt). Groundwater samples showed elevated colloid bound PCDD concentrations (mean 770 ng/kg), mainly octachlorodibenzo-p-dioxin. Groundwater colloids separated by filtration did not show any TCDD. The results support that TCDD/Fs can be relocated from the top soil to the groundwater by colloidal pathway. They did not provide evidence that the dioxins bound to groundwater colloids are leftovers from the Second Indochinese War. However, this study reinforces that the colloidal transport pathway has to be included investigating the relocation of strong sorbing organic contaminants.     

Monitoring of air pollution by polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans of pine needles in Korea

The atmospheric contamination levels of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) were evaluated from the analysis of pine needles in South Korea. Pine needles were collected from 30 sampling points at five main cities in South Korea (Busan, Daegu, Gwangju, Changwon and Jeju island). The highest concentrations of PCDDs/DFs (2.19–26.88 pg I-TEQ/g of dry weight) were measured at Busan, where is the city of the highest population density and traffic volume among five cities. The lowest concentration was detected at Jeju with 0.62 pg I-TEQ/g dry weight, suggesting Jeju could be an environmental background area in Korea. The dominant homologues of PCDDs/DFs in pine needles were the lower chlorine-substituted compounds such as tetra CDDs and CDFs, and the distribution ratios of PCDDs/DFs decreased with increase of the number of chlorine substituents. Homologue profiles of pine needle samples were similar to PCDDs/DFs profiles of the vapor phase in the ambient air, and thus the pine needles absorbed the vapor phase of PCDDs/DFs from air. Results suggested that pine needles could be used as an indicator of the atmospheric contamination for PCDDs/DFs in Korea.     

Biosorption of nickel(II) from aqueous solution by Aspergillus niger: Response surface methodology and isotherm study

In the present study, the effects of biosorbent Aspergillus niger dosage, initial solution pH and initial Ni(II) concentration on the uptake of Ni(II) by NaOH pretreated biomass of A. niger from aqueous solution were investigated. Batch experiments were carried out in order to model and optimize the biosorption process. The influence of three parameters on the uptake of Ni(II) was described using a response surface methodology (RSM) as well as Langmuir and Freundlich isotherm models. Optimum Ni(II) uptake of 4.82 mg Ni(II) g⁻¹ biomass (70.30%) was achieved at pH 6.25, biomass dosage of 2.98 g L⁻¹ and initial Ni(II) concentration of 30.00 mg L⁻¹ Ni(II). Langmuir and Freundlich were able to describe the biosorption isotherm fairly well. However, prediction of Ni(II) biosorption using Langmuir and Freundlich isotherms was relatively poor in comparison with RSM approaches. The biosorption mechanism was also investigated by using Fourier transfer infrared (FT-IR) analysis of untreated, NaOH pretreated, and Ni(II) loaded A. niger biomass.     

Immunotoxicity in ascidians: antifouling compounds alternative to organotins: III--the case of copper(I) and Irgarol 1051

After the widespread ban of TBT, due to its severe impact on coastal biocoenoses, mainly related to its immunosuppressive effects on both invertebrates and vertebrates, alternative biocides such as Cu(I) salts and the triazine Irgarol 1051, the latter previously used in agriculture as a herbicide, have been massively introduced in combined formulations for antifouling paints against a wide spectrum of fouling organisms. Using short-term (60 min) haemocyte cultures of the colonial ascidian Botryllus schlosseri exposed to various sublethal concentrations of copper(I) chloride (LC₅₀ = 281 μM, i.e., 17.8 mg Cu L⁻¹) and Irgarol 1051 (LC₅₀ > 500 μM, i.e., >127 mg L⁻¹), we evaluated their immunotoxic effects through a series of cytochemical assays previously used for organotin compounds. Both compounds can induce dose-dependent immunosuppression, acting on different cellular targets and altering many activities of immunocytes but, unlike TBT, did not have significant effects on cell morphology. Generally, Cu(I) appeared to be more toxic than Irgarol 1051: it significantly (p < 0.05) inhibited yeast phagocytosis at 0.1 μM (∼10 μg L⁻¹), and affected calcium homeostasis and mitochondrial cytochrome-c oxidase activity at 0.01 μM (∼1 μg L⁻¹). Both substances were able to change membrane permeability, induce apoptosis from concentrations of 0.1 μM (∼10 μg L⁻¹) and 200 μM (∼50 mg L⁻¹) for Cu(I) and Irgarol 1051, respectively, and alter the activity of hydrolases. Both Cu(I) and Irgarol 1051 inhibited the activity of phenoloxidase, but did not show any interactive effect when co-present in the exposure medium, suggesting different mechanisms of action.     

Effects of Mn(II) and Fe(II) on microbial removal of arsenic (III)

Goal, scope, and background  Arsenic contamination in groundwater creates severe health problems in the world. There are many physiochemical and biological methods available for remediation of arsenic from groundwater. Among them, microbial remediation could be taken as one of the least expensive methods, though it takes longer treatment time. The main objective of this research was to study the improvement on remediation by addition of some essential ion salts such as Mn and Fe. Materials and methods   Staphylococcus aureus, Bacillus subtilis, Klebsiella oxytoca, and Escherichia coli were taken as model microbes from Dhulikhel, 30 km east from Kathmandu, Nepal. Results and discussion  Microbes used in this study showed different abilities in their removal of As(III) with and without addition of Mn and Fe salts. The trend of remediation increased with time. S. aureus was found to be the best among the microbes used. It showed almost 100% removal after 48-h culture, both with and without Fe and Mn salts. Rate of removal of As increased with addition of Fe and Mn for all microbes. Removal efficiency was found to increase by about 32% on average after addition of salts in 24-h cultures of S. aureus.     

Chlorinated dibenzo-<Emphasis Type="Italic">p</Emphasis>-dioxins and dibenzofurans in the baltic herrinj and sprat of estonian coastal waters

BACKGROUND, AIMS AND SCOPE: The concentration of chlorinated dibenzo-p-dioxins and dibenzofurans in many fish from the Baltic requires monitoring, since it approaches or exceeds the European Union threshold limit value of 4 pg TEQ/g wet weight of fish for human consumption. The concentrations, expressed in TEQs, are important for toxicology and regulations, but hide the concentrations of the individual congeners, which are important for other environmental sciences, source allocation, and for the detection of measurement errors. This report evaluates the results of a survey reported earlier only in the terms of the TEQ concentrations. METHODS: Principal Component Analysis (PCA) was used to reduce the dimensions of the data (17 = 7 chlorinated dibenzo-p-dioxin and 10 chlorinated dibenzofuran congeners) to three principal components. This facilitated the interpretation of the congener profiles. Slopes of the congener concentrations as a function of age of the fish were estimated by least squares regression. The results were compared with a large set of data for lake trout from Lake Ontario. RESULTS AND DISCUSSION: The congener profiles of Baltic herring are less scattered than those of sprat. The profiles of herring from the central Baltic differ from those of herring from the Gulf of Riga and both appear to be affected relatively minimally by the age of the fish. The congener profiles of herring from the western Gulf of Finland are similar to those from the central Baltic, those from middle Gulf of Finland are similar to those from the Gulf of Riga. Both seem to be more affected by age of the fish than the profiles of the first two groups. The concentrations of several pentachloro- and hexachloro-dibenzo-p-dioxins and dibenzofurans increase with the age of the fish CONCLUSION: PCA is a good technique for the evaluation of the congener profiles. The resulting loading and score plots provide a good graphic summary of the multidimensional data. Additional analyses are needed to confirm the observed profile patterns. A comparison with the results of a long-term monitoring from another area shows that the age of the fish is a more important factor than the year of capture. RECOMMENDATION AND OUTLOOK: The surveys should continue for a number of years and the results should be presented and evaluated both in terms of the TEQs as well as in terms of weight concentrations. Since the concentrations do not appear to change very much from year to year, it would be better to carry out surveys only every 3-4 years and, instead, stratify the sampling according to age and gender of the fish, and to analyze replicate extracts by replicate measurements. The inclusion of unmarked replicate samples would be a good quality assurance measure. It would be desirable to analyze additional parts of the food chain in order to understand the fate of the compounds in the ecosystem.     

The impact of production type and region on polychlorinated biphenyl (PCB), polychlorinated dibenzo-p-dioxin and dibenzofuran (PCDD/F) concentrations in Canadian chicken egg yolks

Chicken eggs from five different production types (conventional, omega-3 enriched, free range, organic and free run) were collected, when available, from three regions (west, central and east) of Canada to determine persistent organic pollutant (POP) concentrations. Total polychlorinated biphenyl (PCB) concentrations (∑37 congeners) in yolks from the eggs ranged from 0.162 ng g⁻¹ lipid to 24.8 ng g⁻¹ lipid (median 1.25 ng g⁻¹ lipid) while the concentration of the sum of the 6 indicator PCBs ranged from 0.100 ng g⁻¹ lipid to 9.33 ng g⁻¹ lipid (median 0.495 ng g⁻¹ lipid). Total polychlorinated dibenzo-p-dioxin/dibenzofuran (PCDD/F) concentrations ranged from 2.37 pg g⁻¹ lipid to 382 pg g⁻¹ lipid (median 9.53 pg g⁻¹ lipid). The 2005 WHO toxic equivalency (TEQ) ranged from 0.089 pg TEQ_{PCDD/F+dioxin-like[DL]-PCB} g⁻¹ lipid to 12.8 pg TEQ_{PCDD/F+DL-PCB} g⁻¹ lipid (median 0.342 pg TEQ_{PCDD/F+DL-PCB} g⁻¹ lipid). PCB and PCDD/F concentrations were significantly different (p < 0.001) in egg yolks from different regions of collection. In contrast to observations in Europe, PCB and PCDD/F concentrations in Canadian egg yolks were not impacted solely by the production type (e.g., conventional, free range, organic, etc.) used to maintain the laying chickens. Additionally, only one Canadian free range yolk from western Canada (12.8 pg TEQ_{PCDD/F+DL-PCB} g⁻¹ lipid) exceeded the European toxic equivalent concentration limits for eggs (5 pg TEQ_{PCDD/F+DL-PCB} g⁻¹ lipid). This differs from observations in Europe where free range/home produced eggs frequently have higher POP concentrations than eggs from other production types. Median PCB dietary intake estimates based on consumption of eggs were less than 10 ng d⁻¹ while median PCDD/F intakes were less than 45 pg d⁻¹.     

氢自养生物还原去除地下水中对硝基氯苯(p-NCB)的实验研究

采用批式实验讨论了氢自养还原菌在厌氧条件下,利用氢气作为电子供体还原地下水中对硝基氯苯的可行性及其影响因素.结果表明,氢自养菌能利用氢气生物还原对硝基氯苯,并产生中间产物对氯苯胺,继而进一步还原脱氯产生苯胺,该过程可提高对硝基氯苯的可生化性.对硝基氯苯在初始阶段还原速率较快,最高去除速率达到610μg/(L·d),随后...     

Clearance and recovery of Cd(II) from aqueous solution by magnetic separation technology

An effective method to actualize the recycling use of Cd(II) in industrial wastewater was developed by using the magnetic beads, which was modified with ethylenediamine. When the industrial wastewater was treated with these magnetic beads, the Cd(II) concentration in the solution was sharply reduced to the governmental standard (0.1 μg mL⁻¹) of China. Based on the monolayer adsorption of Cd(II) on the surface of these magnetic beads, the saturation capacity for Cd(II) reached to 68 mg g⁻¹ dried magnetic beads. On the other hand, the binding Cd(II) could be easily recovered in acid conditions and the recovery efficiency exceeded 99%. Thus, in the process of the wastewater purification, the recycling utilization of Cd(II) was realized. Additionally, the excellent capability of regeneration and recycling utilization of these magnetic beads made this technology much suitable for the large-scale application. Compared with the conventional purification methods, the rapid process, simple equipments, easy operation and high efficiency, brought this technology with great potentialities in the treatment of industrial wastewater.     

Removal of Ni(II) and Cu(II) ions using native and acid treated Ni-hyperaccumulator plant Alyssum discolor from Turkish serpentine soil

Alyssum discolor biomass was collected from serpentine soil and was used for removal of metal ions. The plant species grown on serpentine soils are known to be rich with metals ions and thus have more capability for accumulating heavy metals. Native and acid-treated biomass of A. discolor (A. discolor) were utilized for the removal of Ni(II) and Cu(II) ions from aqueous solutions. The effects of contact time, initial concentration, and pH on the biosorption of Ni(II) and Cu(II) ions were investigated. Biosorption equilibrium was established in about 60 min. The surface properties of the biomass preparations were varied with pH, and the maximum amounts of Ni(II) and Cu(II) ions on both A. discolor biomass preparations were adsorbed at pH 5.0. The maximum biosorption capacities of the native, and acid-treated biomass preparations for Ni(II) were 13.1 and 34.7 mg g⁻¹ and for Cu(II) 6.15 and 17.8 mg g⁻¹ dry biomass, respectively. The biosorption of Ni(II) and Cu(II) ions from single and binary component systems can be successfully described by Langmuir and Freundlich isotherms. When the heavy metal ions were in competition, the amounts of biosorbed metal ions on the acid treated plant biomass were found to be 0.542 mmol g⁻¹ for Ni(II) and 0.162 mmol g⁻¹ for Cu(II), the A. discolor biomass was significantly selective for Ni(II) ions. The information gained from these studies was expected to indicate whether the native, and acid-treated forms can have the potential to be used for the removal and recovery of Ni(II) ions from wastewaters.     

Arsenic(III) and iron(II) co-oxidation by oxygen and hydrogen peroxide: Divergent reactions in the presence of organic ligands

Iron-catalyzed oxidation of As(III) to As(V) can be highly effective for toxic arsenic removal via Fenton reaction and Fe(II) oxygenation. However, the contribution of ubiquitous organic ligands is poorly understood, despite its significant role in redox chemistry of arsenic in natural and engineered systems. In this work, selected naturally occurring organic ligands and synthetic ligands in co-oxidation of Fe(II) and As(III) were examined as a function of pH, Fe(II), H₂O₂, and radical scavengers (methanol and 2-propanol) concentration. As(III) was not measurably oxidised in the presence of excess ethylenediaminetetraacetic acid (EDTA) (i.e. Fe(II):EDTA < 1:1), contrasting with the rapid oxidation of Fe(II) by O₂ and H₂O₂ at neutral pH under the same conditions. However, partial oxidation of As(III) was observed at a 2:1 ratio of Fe(II):EDTA. Rapid Fe(II) oxidation in the presence of organic ligands did not necessarily result in the coupled As(III) oxidation. Organic ligands act as both iron speciation regulators and radicals scavengers. Further quenching experiments suggested both hydroxyl radicals and high-valent Fe species contributed to As(III) oxidation. The present findings are significant for the better understanding of aquatic redox chemistry of iron and arsenic in the environment and for optimization of iron-catalyzed arsenic remediation technology.     

The complexation of Cu(II) by anthropogenic fulvic acids extracted from composted urban and livestock wastes

Abstract

The fulvic acid (fua) fractions of two samples of composted solid wastes [urban (urfua) and livestock (lsfua) wastes], commercialized to be used in agriculture as organic correctives or fertilizers, were analyzed for their affinity towards Cu(II) at pH=6. Molecular fluorescence spectroscopy (synchronous mode) was used to monitor the quenching caused by the complexation upon addition of Cu(II) to fua. Spectral data were preprocessed by a chemometric self‐modeling mixture analysis method (SIMPLISMA) to detect the number of different types of fluorescent binding sites that exist in each fua, their spectra and the corresponding quenching profiles [fluorescence intensity as function of the total Cu(II) concentration]. From the analysis of the quenching profiles, the amount of binding sites (Cl) and the corresponding conditional stability constants (K') were calculated. Both fua samples have approximately Cl = 0.21 mmol/g and the logarithms of K’ are 4.21(3) and 4.51(8), respectively for urfua and lsfua. The differences detected between these fua samples and those extracted from natural soils can be attributed mainly to the relatively small humification extent of the present anthropogenic fua samples.